GPUs and the corresponding NVLink bridges get different PEs as they
have separate translation validation entries (TVEs). We put these PEs
to the same IOMMU group so they cannot be passed through separately.
So the iommu_table_group_ops::set_window/unset_window for GPUs do set
tables to the NPU PEs as well which means that iommu_table's list of
attached PEs (iommu_table_group_link) has both GPU and NPU PEs linked.
This list is used for TCE cache invalidation.
The problem is that NPU PE has just a single TVE and can be programmed
to point to 32bit or 64bit windows while GPU PE has two (as any other
PCI device). So we end up having an 32bit iommu_table struct linked to
both PEs even though only the 64bit TCE table cache can be invalidated
on NPU. And a relatively recent skiboot detects this and prints
errors.
This changes GPU's iommu_table_group_ops::set_window/unset_window to
make sure that NPU PE is only linked to the table actually used by the
hardware. If there are two tables used by an IOMMU group, the NPU PE
will use the last programmed one which with the current use scenarios
is expected to be a 64bit one.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With enabled DEBUG, there is a compile error:
"error: ‘flags’ is used uninitialized in this function".
This moves pr_devel() little further where @flags are initialized.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the pseries kernel advertises radix MMU support even if
the actual support is disabled via the CONFIG_PPC_RADIX_MMU option.
This adds a check for CONFIG_PPC_RADIX_MMU to avoid advertising radix
to the hypervisor.
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix the warning messages for stop_machine_change_mapping(), and a number
of other affected functions in its call chain.
All modified functions are under CONFIG_MEMORY_HOTPLUG, so __meminit
is okay (keeps them / does not discard them).
Boot-tested on powernv/power9/radix-mmu and pseries/power8/hash-mmu.
$ make -j$(nproc) CONFIG_DEBUG_SECTION_MISMATCH=y vmlinux
...
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x6b130): Section mismatch in reference from the function stop_machine_change_mapping() to the function .meminit.text:create_physical_mapping()
The function stop_machine_change_mapping() references
the function __meminit create_physical_mapping().
This is often because stop_machine_change_mapping lacks a __meminit
annotation or the annotation of create_physical_mapping is wrong.
WARNING: vmlinux.o(.text+0x6b13c): Section mismatch in reference from the function stop_machine_change_mapping() to the function .meminit.text:create_physical_mapping()
The function stop_machine_change_mapping() references
the function __meminit create_physical_mapping().
This is often because stop_machine_change_mapping lacks a __meminit
annotation or the annotation of create_physical_mapping is wrong.
...
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a definition for cpu_show_spectre_v2() to override the generic
version. This has several permuations, though in practice some may not
occur we cater for any combination.
The most verbose is:
Mitigation: Indirect branch serialisation (kernel only), Indirect
branch cache disabled, ori31 speculation barrier enabled
We don't treat the ori31 speculation barrier as a mitigation on its
own, because it has to be *used* by code in order to be a mitigation
and we don't know if userspace is doing that. So if that's all we see
we say:
Vulnerable, ori31 speculation barrier enabled
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a definition for cpu_show_spectre_v1() to override the generic
version. Currently this just prints "Not affected" or "Vulnerable"
based on the firmware flag.
Although the kernel does have array_index_nospec() in a few places, we
haven't yet audited all the powerpc code to see where it's necessary,
so for now we don't list that as a mitigation.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have the security flags we can simplify the code in
pseries_setup_rfi_flush() because the security flags have pessimistic
defaults.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have the security flags we can significantly simplify the
code in pnv_setup_rfi_flush(), because we can use the flags instead of
checking device tree properties and because the security flags have
pessimistic defaults.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have the security feature flags we can make the
information displayed in the "meltdown" file more informative.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This landed in setup_64.c for no good reason other than we had nowhere
else to put it. Now that we have a security-related file, that is a
better place for it so move it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have feature flags for security related things, set or
clear them based on what we see in the device tree provided by
firmware.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have feature flags for security related things, set or
clear them based on what we receive from the hypercall.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This commit adds security feature flags to reflect the settings we
receive from firmware regarding Spectre/Meltdown mitigations.
The feature names reflect the names we are given by firmware on bare
metal machines. See the hostboot source for details.
Arguably these could be firmware features, but that then requires them
to be read early in boot so they're available prior to asm feature
patching, but we don't actually want to use them for patching. We may
also want to dynamically update them in future, which would be
incompatible with the way firmware features work (at the moment at
least). So for now just make them separate flags.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix the topology kcontrol string handling so that string pointer
references are strdup()ed instead of being copied. This fixes issues
with kcontrol templates on the stack or ones that are freed. Remember
and free the strings too when topology is unloaded.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
gpio-fan cooling device is found by referring to the
"gpio-fan,speed-map" instead.
Remove the unused properties from the gpio-fan node.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
gpio-fan cooling device is found by referring to the
"gpio-fan,speed-map" instead.
Remove the unused properties from the gpio-fan node.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
define the VGA and panel connectors in preparation for DRM.
-----BEGIN PGP SIGNATURE-----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=0XCD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-versatile-drm-dts' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
Pull "DTS changes for RealView+Versatile" from Linus Walleij:
This augments the RealView and Versatile device trees to properly
define the VGA and panel connectors in preparation for DRM.
* tag 'armsoc-versatile-drm-dts' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Augment panel setting for Versatile
ARM: dts: Add Versatile IB2 device tree
ARM: dts: Augment VGA connector bridge on Realview PBX
ARM: dts: Augment VGA connector bridge on Realview EB
ARM: dts: Augment VGA connector bridge on PB1176
ARM: dts: Augment VGA connector bridge on PB11MPcore
- Add registers clock for all the peripheral nodes that had been yet
converted for CP110 (Armada 7K/8K)
- Document URL for schematic for the EspressoBin (Armada 3720)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWq/qJAAKCRALBhiOFHI7
1fG4AJ9sIUoukzIpcerurjS2ycxKHRRMzgCffTzrL1NpcFVahmKpWH0ZVQJTzgc=
=DTZp
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.17-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.17 (part 2)" from Gregory CLEMENT:
- Add registers clock for all the peripheral nodes that had been yet
converted for CP110 (Armada 7K/8K)
- Document URL for schematic for the EspressoBin (Armada 3720)
* tag 'mvebu-dt64-4.17-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: armada-3720-espressobin: Document URL for schematic
ARM64: dts: marvell: armada-cp110: Add registers clock for the PCIe nodes
ARM64: dts: marvell: armada-cp110: Add registers clock for the NAND node
ARM64: dts: marvell: armada-cp110: Add registers clock for the crypto node
ARM64: dts: marvell: armada-cp110: Add registers clock for the trng node
ARM64: dts: marvell: armada-cp110: Add registers clock for XOR engine nodes
ARM64: dts: marvell: armada-cp110: Add registers clock for USB host nodes
We need linux/compiler.h for unreachable(), so #include it here.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We want to avoid pulling linux/preempt.h into cmpxchg.h, since that can
introduce a circular dependency on linux/bitops.h. linux/preempt.h is
only needed by the per-cpu cmpxchg implementation, which is better off
alongside the per-cpu xchg implementation in percpu.h, so move it there
and add the missing #include.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Having asm/cmpxchg.h pull in linux/bug.h is problematic because this
ends up pulling in the atomic bitops which themselves may be built on
top of atomic.h and cmpxchg.h.
Instead, just include build_bug.h for the definition of BUILD_BUG.
Signed-off-by: Will Deacon <will.deacon@arm.com>
When the LL/SC atomics are moved out-of-line, they are annotated as
notrace and exported to modules. Ensure we pull in the relevant include
files so that these macros are defined when we need them.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
fpsimd.h uses the __init annotation, so pull in linux/init.h
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Trivial fix to spelling mistake in dev_err error message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the allocation fails then disable the memcpy support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If there is exactly one CPU present, there is no ambiguity: do not warn
that PMU setup would need to guess IRQ affinity.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On linux-next, I get a build failure in some configurations:
drivers/perf/arm_spe_pmu.c: In function 'arm_spe_pmu_setup_aux':
drivers/perf/arm_spe_pmu.c:857:14: error: implicit declaration of function 'vmap'; did you mean 'swap'? [-Werror=implicit-function-declaration]
buf->base = vmap(pglist, nr_pages, VM_MAP, PAGE_KERNEL);
^~~~
swap
drivers/perf/arm_spe_pmu.c:857:37: error: 'VM_MAP' undeclared (first use in this function); did you mean 'VM_MPX'?
buf->base = vmap(pglist, nr_pages, VM_MAP, PAGE_KERNEL);
^~~~~~
VM_MPX
drivers/perf/arm_spe_pmu.c:857:37: note: each undeclared identifier is reported only once for each function it appears in
drivers/perf/arm_spe_pmu.c: In function 'arm_spe_pmu_free_aux':
drivers/perf/arm_spe_pmu.c:878:2: error: implicit declaration of function 'vunmap'; did you mean 'iounmap'? [-Werror=implicit-function-declaration]
vmap() is declared in linux/vmalloc.h, so we should include that header file.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[will: add additional missing #includes reported by Mark]
Signed-off-by: Will Deacon <will.deacon@arm.com>
platform_driver does not need to set the owner field, as this will
be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Despite the efforts made to correctly read the NDA and CUBC registers,
the order in which the registers are read could sometimes lead to an
inconsistent state.
Re-using the timeline from the comments, this following timing of
registers reads could lead to reading NDA with value "@desc2" and
CUBC with value "MAX desc1":
INITD -------- ------------
|____________________|
_______________________ _______________
NDA @desc2 \/ @desc3
_______________________/\_______________
__________ ___________ _______________
CUBC 0 \/ MAX desc1 \/ MAX desc2
__________/\___________/\_______________
| | | |
Events:(1)(2) (3)(4)
(1) check_nda = @desc2
(2) initd = 1
(3) cur_ubc = MAX desc1
(4) cur_nda = @desc2
This is allowed by the condition ((check_nda == cur_nda) && initd),
despite cur_ubc and cur_nda being in the precise state we don't want.
This error leads to incorrect residue computation.
Fix it by inversing the order in which CUBC and INITD are read. This
makes sure that NDA and CUBC are always read together either _before_
INITD goes to 0 or _after_ it is back at 1.
The case where NDA is read before INITD is at 0 and CUBC is read after
INITD is back at 1 will be rejected by check_nda and cur_nda being
different.
Fixes: 53398f4888 ("dmaengine: at_xdmac: fix residue corruption")
Cc: stable@vger.kernel.org
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* Silk board with R-Car E2 (r8a7794) SoC
- Add r1ex24002 EEPROM to DT
Magnus Damm says "Extend the Silk board support to include U14 which is
an I2C based EEPROM hooked up to the I2C1 bus."
- Add GPIO keys to DT
Magnus Damm says "Extend the Silk board support to include SW3, SW4,
SW6 and SW12. They are all connected via GPIO lines and handled by the
gpio-keys driver"
* Marzen board with R-Car H1 (r7a7779) SoC
- Add SDHI0 VCCQ Regulator
Magnus Damm says "Add support for the on-board voltage regulator hooked
up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
OUT goes to the pull-ups for the data pins of SDHI0."
* Porter board with R-Car M3W (r8a7791) SoC
- Fix HDMI output routing
Laurent Pinchart says "The HDMI encoder is connected to the RGB output
of the DU, which is port@0, not port@1."
* iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
- Enable cmt0
* Stout board with R-Car H2 (r8a7790) SoC
- Initial support
* Lager board with R-Car H2 (r8a7790) SoC
- Add CEC clock for HDMI transmitter
Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
fixed clock for the CEC block. Specify this in the dts to enable CEC
support."
- Move cec_clock to root node
By definition nodes without a bus address do not belong on the bus
* kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
- Fix "debounce-interval" property misspelling
* RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
- Add IPMMU DT nodes
- Add VSP support
* R-Car Gen2 boards
- Use I2C demuxer for
This allows run-time switching between alternate I2C IP blocks
* R-Car Gen2 and RZ/G1 SoCs
- Clean up DT files to ease future maintenance
+ add soc node for IP attached to the bus
+ sort subnodes of soc and root node
+ consistently use single space after =
* R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
- Reduce size of thermal registers
According to the "User's Manual: Hardware" v2.00 the registers at base
0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
case on the r8a73a4 (R-Mobile APE6).
This should not have any runtime affect as mapping granularity is
PAGE_SIZE.
-----BEGIN PGP SIGNATURE-----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=dZnw
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.17" from Simon Horman:
* Silk board with R-Car E2 (r8a7794) SoC
- Add r1ex24002 EEPROM to DT
Magnus Damm says "Extend the Silk board support to include U14 which is
an I2C based EEPROM hooked up to the I2C1 bus."
- Add GPIO keys to DT
Magnus Damm says "Extend the Silk board support to include SW3, SW4,
SW6 and SW12. They are all connected via GPIO lines and handled by the
gpio-keys driver"
* Marzen board with R-Car H1 (r7a7779) SoC
- Add SDHI0 VCCQ Regulator
Magnus Damm says "Add support for the on-board voltage regulator hooked
up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
OUT goes to the pull-ups for the data pins of SDHI0."
* Porter board with R-Car M3W (r8a7791) SoC
- Fix HDMI output routing
Laurent Pinchart says "The HDMI encoder is connected to the RGB output
of the DU, which is port@0, not port@1."
* iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
- Enable cmt0
* Stout board with R-Car H2 (r8a7790) SoC
- Initial support
* Lager board with R-Car H2 (r8a7790) SoC
- Add CEC clock for HDMI transmitter
Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
fixed clock for the CEC block. Specify this in the dts to enable CEC
support."
- Move cec_clock to root node
By definition nodes without a bus address do not belong on the bus
* kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
- Fix "debounce-interval" property misspelling
* RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
- Add IPMMU DT nodes
- Add VSP support
* R-Car Gen2 boards
- Use I2C demuxer for
This allows run-time switching between alternate I2C IP blocks
* R-Car Gen2 and RZ/G1 SoCs
- Clean up DT files to ease future maintenance
+ add soc node for IP attached to the bus
+ sort subnodes of soc and root node
+ consistently use single space after =
* R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
- Reduce size of thermal registers
According to the "User's Manual: Hardware" v2.00 the registers at base
0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
case on the r8a73a4 (R-Mobile APE6).
This should not have any runtime affect as mapping granularity is
PAGE_SIZE.
* tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (47 commits)
ARM: dts: silk: Add GPIO keys to DT
ARM: dts: silk: Add r1ex24002 EEPROM to DT
ARM: dts: marzen: Add SDHI0 VCCQ Regulator
ARM: dts: stout: Initial r8a7790 Stout board support
ARM: dts: lager: Move cec_clock to root node
ARM: dts: kzm9d: Fix "debounce-interval" property misspelling
ARM: dts: gose: use demuxer for I2C4
ARM: dts: gose: use demuxer for I2C2
ARM: dts: silk: use demuxer for I2C1
ARM: dts: alt: use demuxer for I2C1
ARM: dts: porter: use demuxer for I2C2
ARM: dts: koelsch: use demuxer for I2C4
ARM: dts: koelsch: use demuxer for I2C2
ARM: dts: lager: use demuxer for IIC3/I2C3
ARM: dts: lager: use demuxer for IIC2/I2C2
ARM: dts: r8a7745: Add VSP support
ARM: dts: r8a7743: Add VSP support
ARM: dts: r8a7745: Add IPMMU DT nodes
ARM: dts: r8a7743: Add IPMMU DT nodes
ARM: dts: r8a7745: sort subnodes of soc node
...
* R-Car Gen3 boards and SoCs
- Make phy-mode of EtherAVB a board-specific property.
The SoC DTs file now uses "rgmii" and boards override this with
"rgmii-txid" as appropriate. Previously "rgmii-txid" was used
in SoC DTs but this did not describe that more sophiticated
functionality is a board rather than SoC property.
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* R-Car D3 (r8a77995)
- Add I2C nodes and then describing the PCA9654 I/O expander connected to
the I2C0 bus.
* Eagle board with R-Car V3M (r8a77970) SoC
- Enable PFC support for configuring SCIF0 pins
This uses PFC support added to the V3M DT
- Describe EtherAVB PHY IRQ
This uses support for GPIO added to the V3M DT
- Enable I2C0 support
Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor
PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but
we're only describing the former chip now)."
* R-Car V3M (r8a77970) SoCs
- Add PFC support
- Describe GPIO devices
- Describe I2C devices
- Srt subnodes of root node alphabetically to eas future maintence overhead
* Draak board with R-Car D3 (r8a77995) SoC
- Enable SDHI2
Wolfram Sang says "The single SDHI controller is connected to eMMC."
- Enable DU
Kieran Bingham says "Enable the DU, providing only the VGA output for
now."
* R-Car D3 (r8a77995) and V3M (r8a77970) SoCs
- Move nodes which have no reg property out of bus
By deffinition the bus only has hardware with an address on the bus
- Remove non-existing STBE region from EtherAVB
Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs
* R-Car D3 (r8a77995) SoC
- Add FCPV, VSP and DU support
Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances.
One VSPBS can be used as a dual-input image blender, while two VSPD
instances can be utilised as part of a display (DU) pipeline.
Add support for these, along with their required FCPV nodes."
* Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs
- Add GPIO extender
This is a basis for follow-up work to configure the GPIOs of the extender
* Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC
- Initial upstream support
* R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
- Add OPPs table for cpu devices
This, along with recently upstreamed Z and Z2 clock support allows
use of CPUFreq with both A57 and A53 CPUs.
- Add thermal cooling management
Allows the use of CPUFreq as a cooling device on A57 CPUs
- Correct register size of thermal node
Niklas Söderlund says "To be able to read fused calibration values from
hardware the size of the register resource of TSC1 needs to be
incremented to cover one more register which holds the information if
the calibration values have been fused or not.
Instead of increasing TSC1 size to the value from the datasheet update
all TSC's size to the smallest granularity of the address decoder
circuitry"
- Fix register mappings on VSPs
Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the
register space is mapped correctly to support this."
* R-Car H3 (r8a7795) SoC
- Move SCIF node into alphabetical order to ease future maintenance overhead
- Add IPMMU-PV1 device node
This resolves an oversight when IPMMU nodes were added to the H3 DT.
All IPMMU devices should now be described in DT.
- Add missing SYS-DMAC2 dmas
Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that
can make use of DMA are wired to either SYS-DMAC0 only, or to both
SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has
been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25,
2016)."
-----BEGIN PGP SIGNATURE-----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=wu1f
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM64 Based SoC DT Updates for v4.17" from Simon Horman:
* R-Car Gen3 boards and SoCs
- Make phy-mode of EtherAVB a board-specific property.
The SoC DTs file now uses "rgmii" and boards override this with
"rgmii-txid" as appropriate. Previously "rgmii-txid" was used
in SoC DTs but this did not describe that more sophiticated
functionality is a board rather than SoC property.
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* R-Car D3 (r8a77995)
- Add I2C nodes and then describing the PCA9654 I/O expander connected to
the I2C0 bus.
* Eagle board with R-Car V3M (r8a77970) SoC
- Enable PFC support for configuring SCIF0 pins
This uses PFC support added to the V3M DT
- Describe EtherAVB PHY IRQ
This uses support for GPIO added to the V3M DT
- Enable I2C0 support
Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor
PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but
we're only describing the former chip now)."
* R-Car V3M (r8a77970) SoCs
- Add PFC support
- Describe GPIO devices
- Describe I2C devices
- Srt subnodes of root node alphabetically to eas future maintence overhead
* Draak board with R-Car D3 (r8a77995) SoC
- Enable SDHI2
Wolfram Sang says "The single SDHI controller is connected to eMMC."
- Enable DU
Kieran Bingham says "Enable the DU, providing only the VGA output for
now."
* R-Car D3 (r8a77995) and V3M (r8a77970) SoCs
- Move nodes which have no reg property out of bus
By deffinition the bus only has hardware with an address on the bus
- Remove non-existing STBE region from EtherAVB
Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs
* R-Car D3 (r8a77995) SoC
- Add FCPV, VSP and DU support
Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances.
One VSPBS can be used as a dual-input image blender, while two VSPD
instances can be utilised as part of a display (DU) pipeline.
Add support for these, along with their required FCPV nodes."
* Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs
- Add GPIO extender
This is a basis for follow-up work to configure the GPIOs of the extender
* Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC
- Initial upstream support
* R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
- Add OPPs table for cpu devices
This, along with recently upstreamed Z and Z2 clock support allows
use of CPUFreq with both A57 and A53 CPUs.
- Add thermal cooling management
Allows the use of CPUFreq as a cooling device on A57 CPUs
- Correct register size of thermal node
Niklas Söderlund says "To be able to read fused calibration values from
hardware the size of the register resource of TSC1 needs to be
incremented to cover one more register which holds the information if
the calibration values have been fused or not.
Instead of increasing TSC1 size to the value from the datasheet update
all TSC's size to the smallest granularity of the address decoder
circuitry"
- Fix register mappings on VSPs
Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the
register space is mapped correctly to support this."
* R-Car H3 (r8a7795) SoC
- Move SCIF node into alphabetical order to ease future maintenance overhead
- Add IPMMU-PV1 device node
This resolves an oversight when IPMMU nodes were added to the H3 DT.
All IPMMU devices should now be described in DT.
- Add missing SYS-DMAC2 dmas
Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that
can make use of DMA are wired to either SYS-DMAC0 only, or to both
SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has
been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25,
2016)."
* tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (69 commits)
arm64: dts: renesas: v3msk: add SCIF0 pins
arm64: dts: renesas: r8a7795: Add missing SYS-DMAC2 dmas
arm64: dts: renesas: r8a7795: Add IPMMU-PV1 device node
arm64: dts: renesas: r8a77970: sort subnodes of root node alphabetically
arm64: dts: renesas: eagle: add I2C0 support
arm64: dts: renesas: r8a77970: add I2C support
arm64: dts: renesas: r8a77965-salvator-xs: Add SoC name to file header
arm64: dts: renesas: r8a77965: Add EtherAVB device node
arm64: dts: renesas: r8a77970: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: r8a77995: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: r8a7795: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: r8a7796: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: v3msk: Override EtherAVB phy-mode
arm64: dts: renesas: eagle: Override EtherAVB phy-mode
arm64: dts: renesas: draak: Override EtherAVB phy-mode
arm64: dts: renesas: ulcb: Override EtherAVB phy-mode
arm64: dts: renesas: salvator-common: Override EtherAVB phy-mode
arm64: dts: renesas: r8a77965: Add INTC-EX device node
arm64: dts: renesas: r8a77965: Add IIC-DVFS device node
arm64: dts: renesas: Add support for Salvator-XS with R-Car M3-N
...
Adds initial support for the P2972-0000 development board based on
Tegra194 and enables the AHCI controller on Jetson TX1.
-----BEGIN PGP SIGNATURE-----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=u8uZ
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.17-arm64-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "arm64: tegra: Device tree changes for v4.17-rc1" from Thierry Reding:
Adds initial support for the P2972-0000 development board based on
Tegra194 and enables the AHCI controller on Jetson TX1.
* tag 'tegra-for-4.17-arm64-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable AHCI on Jetson TX1
arm64: tegra: Add SATA node for Tegra210
arm64: tegra: Add device tree for the Tegra194 P2972-0000 board
arm64: tegra: Add Tegra194 chip device tree
Support for the VDE is added on Tegra30 along with some general cleanup
and some improvements to the various Toradex boards.
-----BEGIN PGP SIGNATURE-----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=Dqxp
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.17-arm-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "ARM: tegra: Device tree changes for v4.17-rc1" from Thierry Reding:
Support for the VDE is added on Tegra30 along with some general cleanup
and some improvements to the various Toradex boards.
* tag 'tegra-for-4.17-arm-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: apalis-tk1: Support v1.2 hardware revision
ARM: tegra: apalis-tk1: Copyright period, spurious newlines
ARM: tegra: apalis-tk1: Hog group for ethernet, PCIe, reset GPIOs
ARM: tegra: apalis-tk1: Add missing as3722 gpio0 configuration
ARM: tegra: apalis-tk1: Activate PWM pin muxing for pwm3
ARM: tegra: apalis-tk1: Set critical trips
ARM: tegra: apalis/colibri: Remove unneeded reg property
ARM: tegra: apalis/colibri: Use correct compatible for RTC
ARM: tegra: Fix I2C bus frequencies on Apalis/Colibri
ARM: tegra: venice2: Remove duplicate pcie-1 node
ARM: tegra: beaver: Remove invalid uses of rsvd1
ARM: tegra: Use proper IRQ type definitions
ARM: tegra: Fix ULPI regression on Tegra20
ARM: tegra: Add unit address to VDE IRAM area
ARM: tegra: Add video decoder node on Tegra30
ARM: tegra: Add IRAM node on Tegra30
Mostly cleanup of existing bindings and initial support for Tegra194.
-----BEGIN PGP SIGNATURE-----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=7+yt
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.17-dt-bindings' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "dt-bindings: Tegra changes for v4.17-rc1" from Thierry Reding:
Mostly cleanup of existing bindings and initial support for Tegra194.
* tag 'tegra-for-4.17-dt-bindings' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt/bindings: Fix binding examples for Tegra GMI controller
dt-bindings: phy: Clarify ULPI PHY source clock
dt-bindings: tegra: Add documentation for nvidia,tegra194-pmc
dt-bindings: tegra: Add missing chips and NVIDIA boards
The first and second patches fix the regulator support for the Bananapi M2
board.
The last one updates my email address in MAINTAINERS.
-----BEGIN PGP SIGNATURE-----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=GQc4
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner Fixes for 4.16" from Maxime Ripard:
The first and second patches fix the regulator support for the Bananapi M2
board.
The last one updates my email address in MAINTAINERS.
* tag 'sunxi-fixes-for-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
MAINTAINERS: update email address for Maxime Ripard
ARM: dts: sun6i: a31s: bpi-m2: add missing regulators
ARM: dts: sun6i: a31s: bpi-m2: improve pmic properties
Fix insecure W+X mapping warning for SRAM for omaps that
don't yet use drivers/misc/*sram*.c code. An earlier attempt
at fixing this turned out to cause problems with PM on omap3,
this version works with PM on omap3.
Also fix dmtimer probe for omap16xx devices that was noticed
with the pending dmtimer move to drivers. It seems this has
been broken for a while and is a non-critical for booting.
It is needed for PM on omap16xx though.
-----BEGIN PGP SIGNATURE-----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=/ZXy
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/sram-fix-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "Two fixes for omap variants for v4.16-rc cycle" from Tony Lindgren:
Fix insecure W+X mapping warning for SRAM for omaps that
don't yet use drivers/misc/*sram*.c code. An earlier attempt
at fixing this turned out to cause problems with PM on omap3,
this version works with PM on omap3.
Also fix dmtimer probe for omap16xx devices that was noticed
with the pending dmtimer move to drivers. It seems this has
been broken for a while and is a non-critical for booting.
It is needed for PM on omap16xx though.
* tag 'omap-for-v4.16/sram-fix-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Fix SRAM W+X mapping
ARM: OMAP: Fix dmtimer init for omap1