Core & protocols
----------------
- A few steps lowering rtnl_lock dependence:
- per-netns netdev unregistration for select SW drivers
(e.g. veth, ipvlan, tunnels)
- rtnl_lock-less FIB rule changes (RTM_NEWRULE and RTM_DELRULE)
- prepare software drivers and TC qdiscs for rtnl_lock-less GET
- Support BIG TCP (>64kB TSO) in UDP tunnels (vxlan, geneve).
- Support buffers larger than PAGE_SIZE in devmem zero-copy API.
- Improve MPTCP handling of extreme memory pressure handling,
when out-of-order queue had to be pruned.
- Report the per-group user count via RTM_GETMULTICAST.
- Expose the route deletion reason in RTM_DELROUTE.
- Add a SO_RIGHTS_NOTRUNC option to UNIX sockets to enable more useful
handling of LSM denials when receiving SCM_RIGHTS messages: instead
of truncating the message at the first blocked fd, keep every fd slot
and store the LSM errno in the blocked slot.
- IPv6 Segment Routing - support looking up the post-encap SID
(address) in a different/specified routing table.
- Support PRP RedBox (interlink) creation.
- Support per-nexthop UDP dst port in VXLAN.
- Continue converting getsockopt callbacks in a number of protocols
to iov_iter.
Ethernet
--------
- Marge initial CXL support for AMD/Solarflare NICs (shared branch
with the CXL tree).
- New drivers:
- ADIN1140 10BASE-T1S MACPHY
- Initial skeleton of Intel iXD and ZTE Dinghai drivers.
- High-speed NICs:
- AMD/Pensando:
- support firmware flashing
- Cisco (enic):
- SR-IOV V2 admin channel and MBOX protocol
- Huawei (hns3):
- support for ethtool pfc_prevention_tout
- nVidia/Mellanox:
- support sharing bandwidth control across interfaces of
the same device
- Marvell (octeontx2-pf):
- link RQ page pools to netdev for Netlink stats
- Google vNIC:
- XDP metadata support for DQ RDA
- Microsoft vNIC:
- support forcing full-page RX buffers
- Other NICs:
- Synopsys IP:
- eic7700: support for eth1
- Microchip (lan743x):
- support for RMII interface
- Wangxun:
- support for ethtool -G and -C for VFs
- add Tx timeout and PCIe error handling
- Intel (igb/igc):
- RSS key get/set support
- support for forcing link speed without auto-negotiation
- Switches:
- NXP (dpaa2):
- support bonding/LAG offload
- Mediatek:
- mt7530: EN7528 support
- initial support for MT7628
- Micrel (ksz8/9):
- refactoring work to move towards library model
- PTP support for KSZ8463
- nVidia/Mellanox:
- support rtnl-lock-less ethtool callbacks
- Realtek:
- rtl8366rb: use generic RTL83xx code
- support SGMII and HSGMII for RTL8367S
- PHYs:
- Airoha:
- EcoNet EN7528 PHY support
- DAPU Telecom
- DAPU Telecom DAP8211R(I) Gigabit PHY support
- Realtek:
- support RTL8261C_CG
- support RTL8261D
Wireless
--------
- nl80211: per-link statistics support for multi-link operation
- mac80211: AQL/airtime-fairness support for multicast
- Merge Peripheral Authentication Service (PAS) / TEE support
for ath12k (shared branch with the firmware/qcom tree).
- New drivers:
- mm81x for Morse Micro Long-Range S1G devices
- nxpwifi for NXP devices (mostly forked off from mwifiex)
- Driver changes:
- Broadcom (brcmfmac):
- DPP support, some Cypress part update
- MediaTek (mt76):
- mt7928 support
- mt7925 NAN support
- mt7996 AP powersave improvements
- Qualcomm (ath12k):
- much kernel infrastructure integration work
- AHB platform MultiPD support
- Realtek (rt89):
- LED support
- RTL8922DE support
- dual-BT coex for RTL8922D
- Intel:
- new FW version support
Bluetooth
---------
- HCI: add support for Shorter Connection Interval (SCI) feature.
- af_bluetooth: add minimal context analysis annotations.
- Driver changes:
- Intel:
- add Bluetooth SAR revision 2 support
- add vendor_reset PCI sysfs for PLDR
- Mediatek:
- add USB IDs for MT7902 and MT7922 devices
- Realtek:
- add USB IDs for 8761CU and 8852BE devices
- NXP:
- add M.2 Bluetooth device support using pwrseq
Misc
----
- DPLL support for manual/numerical oscillator control (NCO)
(implement in zl3073x).
- MCTP support for MCTP over USB v1.1 (DMTF DSP0283).
- Power-over-Ethernet: support Realtek PSE controllers.
- Remove the IBM EHEA driver.
- Remove tulip/xircom_cb driver.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=zDto
-----END PGP SIGNATURE-----
Merge tag 'net-next-7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"One of the 'small improvements all over the place' releases for us.
It's hard to draw any direct comparisons because summer vacations
disrupted our patch processing (and presumably - generation) quite a
bit.
Quick and dirty count suggests we (Paolo and I) merged a very similar
number of net (632) and net-next (648) patches. This is not telling
the full story either because 1/3 to 1/2 of the net-next patches also
*seem* like AI-driven low priority fixes, cleanups and clarifications.
We are completely overwhelmed, of course. The glimmer of hope is that
we secured sufficient LLM budget and access (thank you Meta!) to run
reviews with multiple frontier models on each patch. This eliminates
some hallucinations. That said, in terms of review, the LLMs can only
do so much.
The sad truth is that our APIs (especially for rare events like PCIe
errors, timeouts etc) have always been racy, and now LLMs don't let us
ignore that. I expect our direction for the next release will be to
tweak the reviews a little bit more, but start shifting focus to
letting the LLMs take care of the busy work - managing patchwork,
automating common process complaints, editing commit messages, and
maybe applying patches which already got "reviewed-by" tags from
people we trust...
Core & protocols:
- A few steps lowering rtnl_lock dependence:
- per-netns netdev unregistration for select SW drivers (e.g.
veth, ipvlan, tunnels)
- rtnl_lock-less FIB rule changes (RTM_NEWRULE and RTM_DELRULE)
- prepare software drivers and TC qdiscs for rtnl_lock-less GET
- Support BIG TCP (>64kB TSO) in UDP tunnels (vxlan, geneve)
- Support buffers larger than PAGE_SIZE in devmem zero-copy API
- Improve MPTCP handling of extreme memory pressure handling, when
out-of-order queue had to be pruned
- Report the per-group user count via RTM_GETMULTICAST
- Expose the route deletion reason in RTM_DELROUTE
- Add a SO_RIGHTS_NOTRUNC option to UNIX sockets to enable more
useful handling of LSM denials when receiving SCM_RIGHTS messages:
instead of truncating the message at the first blocked fd, keep
every fd slot and store the LSM errno in the blocked slot
- IPv6 Segment Routing - support looking up the post-encap SID
(address) in a different/specified routing table
- Support PRP RedBox (interlink) creation
- Support per-nexthop UDP dst port in VXLAN
- Continue converting getsockopt callbacks in a number of protocols
to iov_iter
Ethernet:
- Merge initial CXL support for AMD/Solarflare NICs (shared branch
with the CXL tree)
- New drivers:
- ADIN1140 10BASE-T1S MACPHY
- Initial skeleton of Intel iXD and ZTE Dinghai drivers
- High-speed NICs:
- AMD/Pensando:
- support firmware flashing
- Cisco (enic):
- SR-IOV V2 admin channel and MBOX protocol
- Huawei (hns3):
- support for ethtool pfc_prevention_tout
- nVidia/Mellanox:
- support sharing bandwidth control across interfaces
of the same device
- Marvell (octeontx2-pf):
- link RQ page pools to netdev for Netlink stats
- Google vNIC:
- XDP metadata support for DQ RDA
- Microsoft vNIC:
- support forcing full-page RX buffers
- Other NICs:
- Synopsys IP:
- eic7700: support for eth1
- Microchip (lan743x):
- support for RMII interface
- Wangxun:
- support for ethtool -G and -C for VFs
- add Tx timeout and PCIe error handling
- Intel (igb/igc):
- RSS key get/set support
- support for forcing link speed without auto-negotiation
- Switches:
- NXP (dpaa2):
- support bonding/LAG offload
- Mediatek:
- mt7530: EN7528 support
- initial support for MT7628
- Micrel (ksz8/9):
- refactoring work to move towards library model
- PTP support for KSZ8463
- nVidia/Mellanox:
- support rtnl-lock-less ethtool callbacks
- Realtek:
- rtl8366rb: use generic RTL83xx code
- support SGMII and HSGMII for RTL8367S
- PHYs:
- Airoha:
- EcoNet EN7528 PHY support
- DAPU Telecom
- DAPU Telecom DAP8211R(I) Gigabit PHY support
- Realtek:
- support RTL8261C_CG
- support RTL8261D
Wireless:
- nl80211: per-link statistics support for multi-link operation
- mac80211: AQL/airtime-fairness support for multicast
- Merge Peripheral Authentication Service (PAS) / TEE support for
ath12k (shared branch with the firmware/qcom tree)
- New drivers:
- mm81x for Morse Micro Long-Range S1G devices
- nxpwifi for NXP devices (mostly forked off from mwifiex)
- Driver changes:
- Broadcom (brcmfmac):
- DPP support, some Cypress part update
- MediaTek (mt76):
- mt7928 support
- mt7925 NAN support
- mt7996 AP powersave improvements
- Qualcomm (ath12k):
- much kernel infrastructure integration work
- AHB platform MultiPD support
- Realtek (rt89):
- LED support
- RTL8922DE support
- dual-BT coex for RTL8922D
- Intel:
- new FW version support
Bluetooth:
- HCI: add support for Shorter Connection Interval (SCI) feature
- af_bluetooth: add minimal context analysis annotations
- Driver changes:
- Intel:
- add Bluetooth SAR revision 2 support
- add vendor_reset PCI sysfs for PLDR
- Mediatek:
- add USB IDs for MT7902 and MT7922 devices
- Realtek:
- add USB IDs for 8761CU and 8852BE devices
- NXP:
- add M.2 Bluetooth device support using pwrseq
Misc:
- DPLL support for manual/numerical oscillator control (NCO)
(implement in zl3073x)
- MCTP support for MCTP over USB v1.1 (DMTF DSP0283)
- Power-over-Ethernet: support Realtek PSE controllers
- Remove the IBM EHEA driver
- Remove tulip/xircom_cb driver"
* tag 'net-next-7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1433 commits)
net/mlx5e: do not HW-GRO coalesce small frames
net: openvswitch: fix nf_connlabels leak in ovs_ct_init
net: add missing ref_tracker_dir_exit() to alloc_netdev_mqs()
net: openvswitch: fix flow mask use-after-free on flow deletion
sctp: stop processing a packet once its association is deleted
dpll: zl3073x: add PTP clock support
dpll: zl3073x: add channel ToD, phase step and TIE operations
dpll: zl3073x: scale poll interval proportionally to timeout
ptp: vmclock: prevent read-only mappings from becoming writable
ipv4: reject undersized MTUs in ip_do_fragment()
bonding: initialize err for empty target lists
net: dsa: initial support for MT7628 embedded switch
net: dsa: initial MT7628 tagging driver
net: phy: mediatek: add phy driver for MT7628 built-in Fast Ethernet PHYs
dt-bindings: net: dsa: add MT7628 ESW
net: pse-pd: realtek-pse-mcu: add UART transport
net: pse-pd: realtek-pse-mcu: add I2C transport
net: pse-pd: add Realtek PSE MCU core
dt-bindings: net: pse-pd: add bindings for Realtek PSE MCU
vsock: use sock_error() to consume sk_err after a failed connect
...
-----BEGIN PGP SIGNATURE-----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=8fcn
-----END PGP SIGNATURE-----
Merge tag 'media/v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- v4l2-core: added ISP statistics support and per-block validation
- v4l2-core: Allow unknown HDR10 white point and luminance
- New camera sensors: Sony IMX678 and IMX471m, Himax HM1092 IR sensor
- New codec: Milos: VPU v2.0 codec support
- isp driver: gained support for Dreamchip RPPX1 ISP framework
- vsp1 driver: gained support for RZ/T2H and RZ/N2H
- Novalake driver: gained CVS support for new NVL hardware
- dvb-core: fix feed leak on failed DMX_ADD_PID
- several driver fixes, cleanups and minor improvements
* tag 'media/v7.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (308 commits)
media: ipu-bridge: check all DMI entries when overriding sensor rotation
media: v4l2-async: avoid deleting unlinked ASC entry on link error
media: rzg2l-cru: Align bytesperline to hardware DMA stride requirement
media: intel/ipu6: fix async notifier cleanup leak on parse error
media: staging/ipu7: fix async notifier UAF on probe error path
media: amd: isp4: fix self-deadlock in isp4sd_pwron_and_init() error path
media: amd: isp4: release partial allocations in isp4if_alloc_fw_gpumem()
media: rcar-isp: Fix VSPX reference leaks
media: rcar-isp: Release ISPCORE resources
media: i2c: imx415: Release runtime PM reference on VBLANK error
media: i2c: imx415: Return test pattern write errors
media: renesas: vsp1: Declare index variables in for loop statement
media: renesas: vsp1: Make reset control optional to support platforms without a reset line
media: dt-bindings: media: renesas,vsp1: Document RZ/T2H and RZ/N2H SoCs
media: dt-bindings: media: renesas,fcp: Document RZ/T2H and RZ/N2H SoCs
media: nxp: imx8-isi: Add additional 32-bit RGB format support
media: nxp: imx8-isi: Add 16-bit raw Bayer format support
media: nxp: imx8-isi: Implement per-stream reference counting for multiplexed streams
media: nxp: imx8-isi: Use BIT_ULL() for 64-bit stream masks
media: nxp: imx8-isi: Correct color map between V4L2 and ISI
...
isys_register_devices() registers the V4L2 async notifier via
isys_notifier_init(). If a subsequent probe step such as
isys_fw_log_init() fails, isys_probe() jumps to the out_cleanup label
which only calls isys_unregister_devices(). That helper tears down the
video devices, subdevices, V4L2 device and media device, but never
unregisters or cleans up the async notifier.
As a result the notifier stays chained in the global notifier_list while
the enclosing struct ipu7_isys is freed by devres, leading to list
corruption and a use-after-free the next time the list is walked.
The remove path already does the right thing by calling
isys_notifier_cleanup() before isys_unregister_devices(). Mirror that on
the probe error path so the notifier is unregistered and cleaned up
before the device is torn down.
Fixes: a516d36bdc ("media: staging/ipu7: add IPU7 input system device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Cong Nguyen <congnt264@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
- iwlwifi: new FW version support
- mt76:
- mt7928 support
- mt7925 NAN support
- mt7996 AP powersave improvements
- rtw89:
- LED support
- RTL8922DE support
- dual-BT coex for RTL8922D
- ath12k: AHB platform MultiPD support
- cfg80211: pre-assign cookies for operations
- mac80211: AQL support for multicast
-----BEGIN PGP SIGNATURE-----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=L5q1
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2026-08-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Quite a bunch more work, of note:
- iwlwifi: new FW version support
- mt76:
- mt7928 support
- mt7925 NAN support
- mt7996 AP powersave improvements
- rtw89:
- LED support
- RTL8922DE support
- dual-BT coex for RTL8922D
- ath12k: AHB platform MultiPD support
- cfg80211: pre-assign cookies for operations
- mac80211: AQL support for multicast
* tag 'wireless-next-2026-08-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (403 commits)
wifi: nxpwifi: bound uAP association event IEs to the event buffer
wifi: nxpwifi: detach sync command buffer on interrupted wait
wifi: brcmfmac: Fix memory leak in brcmf_sdio_read_control()
wifi: rsi: Fix types to appease CFI
wifi: mac80211: skip default WMM setup for AP_VLAN links
wifi: nxpwifi: fix multiple static analysis errors and warnings
wifi: morsemicro: MM81X should be invisible and selected by its users
wifi: nxp: NXPWIFI should be invisible and selected by its users
wifi: cfg80211: stop PMSR before P2P and NAN teardown
wifi: mac80211: disconnect on CSA to channel 0
wifi: brcmfmac: fix P2P action frame handling without device vif
wifi: brcmfmac: Set DMA direction for msgbuf packet IDs
wifi: brcmfmac: validate msgbuf flowring IDs before use
wifi: mac80211: fix RCU usage in peer probing
wifi: mac80211: fix RCU dereference in throughput estimate
wifi: wilc1000: validate monitor transmit frame headers
wifi: mac80211: skip unused probe response countdown offsets
wifi: zd1211rw: reject secondary interfaces to prevent conflicts
wifi: nl80211: clean up color-change beacon data on errors
wifi: mac80211: send TWT teardown to peer after setup TX failure
...
====================
Link: https://patch.msgid.link/20260806121304.190084-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The remain_on_channel, mgmt_tx, and probe_peer ops previously used
a u64 *cookie output parameter. Now that cfg80211 pre-assigns the
cookie value before invoking drivers, the parameter conveys a value
from caller to driver, not the other way around. Convert it to a
plain u64 input parameter across the ops struct (cfg80211.h),
rdev-ops.h wrappers, nl80211.c/mlme.c call sites, mac80211, and
all driver implementations.
The tx_control_port op is excluded: its cookie pointer is nullable
(passed as NULL when dont_wait_for_ack is set), so the nullable
pointer semantics are still required.
Internal mac80211 helpers ieee80211_start_roc_work() and
ieee80211_attach_ack_skb() still take u64 *cookie because they
assign to the pointee; their callers now pass &cookie to take the
address of the local value parameter.
wil6210's internal wil_p2p_listen() is also updated to take u64
cookie since it is called directly from the remain_on_channel
callback.
Assisted-by: Claude:claude-sonnet-4-6
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260731123509.1975281-12-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stop using params->buf address as cookie value and simply pass the
pre-assigned cookie in frame tx status. This implementation seems
to fire-and-forget the transmitted frame as the cookie is not used
in any other way.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260731123509.1975281-11-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
isys_notifier_init() initialises a v4l2 async notifier and then, for
each CSI-2 port, adds a remote sensor subdev to the notifier's
waiting_list via v4l2_async_nf_add_fwnode_remote(), which allocates a
sensor_async_sd descriptor and takes a fwnode reference.
If parsing or adding a later port fails, the code jumps to the
"err_parse" label, which only drops the current endpoint fwnode
reference and returns, without calling v4l2_async_nf_cleanup(). Any
descriptors already added to the notifier for earlier ports are
therefore leaked, and the caller's error path does not clean up the
notifier either.
Call v4l2_async_nf_cleanup() on the error path, matching the cleanup
already performed when v4l2_async_nf_register() fails. This is safe as
the notifier is always initialised before the loop is entered.
Fixes: a516d36bdc ("media: staging/ipu7: add IPU7 input system device driver")
Signed-off-by: Cong Nguyen <congnt264@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Wrap long function arguments under the starting
parentheses because of line length style warning
reported by checkpatch.pl
Signed-off-by: Faisal Mukhtar <mukhtarfaisal03@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
rtw_cfg80211_monitor_if_xmit_entry() removes the radiotap header and
then reads the 802.11 frame control field without checking that a base
802.11 header remains.
The data path also pulls the calculated 802.11, QoS and SNAP header
span before confirming that the skb contains it. A truncated frame can
therefore cause out-of-bounds reads or leave insufficient data for the
Ethernet address writes.
Reject frames that do not contain the base 802.11 header and data
frames that do not contain their complete calculated header span.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Mariano Baragiola <mbaragiola@linux.com>
Link: https://patch.msgid.link/20260727160859.1917096-1-mbaragiola@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WEP shared-key authentication handler uses the challenge-text
element's attacker-controlled length without checking it against the
fixed 128-byte chg_txt buffer.
In OnAuthClient() the length from rtw_get_ie() - up to 255 - is used
to perform memcpy() into the 128-byte pmlmeinfo->chg_txt, so a
malicious AP sending a malformed WLAN_EID_CHALLENGE element can
overflow/underfill chg_txt by up to 127 bytes. It is reachable over the
air, before association, during shared-key authentication. In the case
of an overflow, the driver can write out of bounds. In the case of an
underfill, the driver can echo stale buffer memory.
The challenge text is defined to be exactly 128 octets, which is
already provided as the WLAN_AUTH_CHALLENGE_LEN define; require the
element to be exactly that length before use.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Panagiotis Petrakopoulos <npetrakopoulos2003@gmail.com>
Link: https://patch.msgid.link/20260720082409.168379-1-npetrakopoulos2003@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WMM_param_handler() copies a fixed-size WMM parameter element out of a
received information element without checking that the element is long
enough, causing an out-of-bounds read for a short WMM IE.
The handler reads sizeof(struct WMM_para_element) (18) bytes at
pIE->data + 6, so it requires pIE->length to be at least 24
(WLAN_WMM_LEN), but it never validates the length. Two of its three
callers reach it after matching only the WMM OUI: OnAssocRsp() in
rtw_mlme_ext.c matches a 6-byte OUI, and join_cmd_hdl() matches a
4-byte OUI, before calling the handler. A vendor-specific IE carrying
the WMM OUI but a length between 6 and 23, placed in an association
response or in the IE blob handed to join_cmd_hdl(), passes the OUI
check and then makes the memcmp() and memcpy() at pIE->data + 6 read
past the end of the element. OnAssocRsp() parses a frame received from
the AP, so this is reachable from a remote peer.
The remaining caller in rtw_wlan_util.c already guards the handler with
"pIE->length == WLAN_WMM_LEN". Move the equivalent check into the
handler itself so every caller is covered; the sibling IE handlers in
the same parsing loop (HT_caps_handler(), HT_info_handler(),
ERP_IE_handler()) likewise bound their accesses by pIE->length.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable@vger.kernel.org
Signed-off-by: Muhammad Bilal <meatuni001@gmail.com>
Link: https://patch.msgid.link/20260719041509.97894-1-meatuni001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtw_get_wpa_ie() reads bytes at fixed offsets into a vendor-specific
information element without checking that the element is long enough,
causing an out-of-bounds read for a short trailing IE.
The function locates a vendor-specific IE (EID 221) with rtw_get_ie()
and then compares a 4-byte OUI+type at pbuf + 2 and reads a 2-byte
version word at pbuf + 6. Those accesses require the IE body to be at
least 6 bytes, but rtw_get_ie() only guarantees that the element fits
within the buffer; it does not enforce a minimum body length. A
vendor-specific IE whose length byte is 0 to 5, placed at the end of
the buffer, therefore makes these reads run past the end of the IE and
past the end of the buffer itself.
The buffer holds information elements taken from received management
frames and from the IE blob passed to rtw_cfg80211_set_wpa_ie(), which
is kmemdup'd to its exact length, so the read can run off the end of
the allocation.
The sibling helpers rtw_get_sec_ie(), rtw_get_wapi_ie() and
rtw_get_wps_ie() in this file already reject too-short vendor-specific
IEs before their OUI memcmp(); rtw_get_wpa_ie() was never brought in
line with them, and needs a minimum of 6 rather than 4 bytes because
of the version word. Add the missing length check.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Muhammad Bilal <meatuni001@gmail.com>
Link: https://patch.msgid.link/20260719030631.88254-1-meatuni001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtw_get_wps_ie() iterates over IE data from network frames without
validating that the IE header and payload fit within the remaining
buffer before reading them. Specifically:
- in_ie[cnt + 1] is read without checking cnt + 1 < in_len
- memcmp(&in_ie[cnt + 2], ...) accesses cnt + 2 without bounds check
- in_ie[cnt + 1] is used as length without verifying payload fits
Add bounds checks at the top of the loop body to break early if fewer
than 2 bytes remain for the IE header, or if the declared payload
extends past the end of the buffer. Also require at least 4 bytes of
payload before comparing the WPS OUI.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Moksh Panicker <mokshpanicker.7@gmail.com>
Link: https://patch.msgid.link/20260625202911.26782-1-mokshpanicker.7@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtw_get_chan_type() maps the driver's channel offset to nl80211 channel
types the wrong way around.
In this driver HAL_PRIME_CHNL_OFFSET_LOWER means the primary channel is
the lower 20 MHz half of the 40 MHz pair, i.e. the secondary channel is
above the primary one: rtw_get_center_ch() computes the center channel
as "channel + 2" for OFFSET_LOWER, and bwmode_update_check() sets
OFFSET_LOWER when the AP's HT operation IE announces SCA (secondary
channel above). In nl80211 terms that is NL80211_CHAN_HT40PLUS, not
HT40MINUS.
Because of the inversion, cfg80211_rtw_get_channel() reports an HT40+
association as HT40-. For an HT40+ AP on a low channel (e.g. channel 3)
the resulting chandef spans below the 2.4 GHz band edge and is invalid,
so the regulatory core tears the connection down 60 seconds
(REG_ENFORCE_GRACE_MS) after the AP's country IE triggers a regdomain
change: reg_check_chans_work() considers the reported chandef unusable
and calls cfg80211_leave(). The supplicant then reconnects, the country
IE changes the regdomain again, and the cycle repeats, causing a
disconnect/reconnect loop every ~65 seconds for as long as the link is
up.
Observed on a TECLAST X80 Power tablet (RTL8723BS) associated to an
HT40+ AP on channel 3 with a KR country IE; a kprobe trace showed
cfg80211_disconnect() being invoked from reg_check_chans_work(). With
the mapping fixed, "iw dev wlan0 info" reports the correct
"width: 40 MHz, center1: 2432 MHz" and the periodic disconnects stop.
Fixes: 5402cc178c ("staging: rtl8723bs: add get_channel cfg80211 implementation")
Cc: stable@vger.kernel.org
Assisted-by: Claude-Code:claude-fable-5 bpftrace
Signed-off-by: MinJea Kim <qndkdrnl@gmail.com>
Link: https://patch.msgid.link/20260714131421.3980-1-qndkdrnl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cedrus_init_ctrls(), the V4L2 control handler is initialized before
allocating memory for ctx->ctrls. If this allocation fails, the function
returns -ENOMEM without freeing the previously allocated handler
resources, leading to a memory leak.
Fix this by calling v4l2_ctrl_handler_free() on the ctx->ctrls allocation
failure path.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1.1.
An x86_64 allyesconfig build showed no new warnings. As we do not have an
Allwinner SoC or board with a Cedrus VPU available to test with, no
runtime testing was able to be performed.
Fixes: 50e761516f ("media: platform: Add Cedrus VPU decoder driver")
Cc: stable@vger.kernel.org
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
When VIDIOC_TRY_FMT is called with an unsupported pixel format on the
OUTPUT queue, vdec_try_fmt_common() falls back to V4L2_PIX_FMT_MPEG2.
However, if a distro has locally patched MPEG2 support out (as it has
been broken for some time) the platform format table does not contain
MPEG2 so find_format() returns NULL and the subsequent dereference of
fmt_out->max_width triggers a NULL pointer dereference.
Fix this by falling back to the first format in the platform's format
array instead of hardcoding V4L2_PIX_FMT_MPEG2. This is always valid
since every platform defines at least one format.
Fixes: 3e7f51bd96 ("media: meson: add v4l2 m2m video decoder driver")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The atomisp code has been very heavily annotated in doxygen format.
Unfortunately, both doxygen and kernel-doc use the same mark for signify
the beginning of a comment (/**).
As a result of this, kernel-doc gets confused when it parses atomisp and
throws tons of warnings, which made us completely disable atomisp
kernel-doc checks in Media-CI.
Demote all the broken comments so we can have 100% coverage.
Future patches can convert the doxygen annotations to kernel-doc if this
is deemed useful.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
tegra_vi_channels_alloc() iterates over port nodes and skips those
whose reg property cannot be read or whose remote endpoint fails
v4l2_fwnode_endpoint_parse(), leaving the negative result of the
failed call in ret. If that happens on the last port node, the loop
ends with ret still negative and tegra_vi_init() fails the whole VI
probe.
The same defective port earlier in the ports node is skipped silently,
so probing succeeds or fails depending on the order of the port nodes.
The CSI equivalent, tegra_csi_channels_alloc(), returns 0
unconditionally after its loop and does not have this problem.
Use a separate variable for the per-port checks so that only fatal
errors end up in ret.
Fixes: 1ebaeb0983 ("media: tegra-video: Add support for external sensor capture")
Fixes: 2ac4035a78 ("media: tegra-video: Add support for x8 captures with gang ports")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-fable-5
Signed-off-by: Hao-Qun Huang <alvinhuang0603@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
tegra_vip_channel_of_parse() initializes np from dev->of_node without
taking a reference, but its error paths drop one through the
err_node_put label. This underflows the refcount of the VIP device's
OF node when endpoint parsing fails on a malformed device tree.
The only reference the function takes on np is the success-path
of_node_get() stored in vip->chan.of_node, and that one is already
released by the tegra_vip_init() error path and by tegra_vip_exit().
Return errors directly instead of jumping to the bogus cleanup label.
Fixes: e740d199cf ("staging: media: tegra-video: add support for Tegra20 parallel input")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-fable-5
Signed-off-by: Hao-Qun Huang <alvinhuang0603@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The existing tegra_vi_graph_build function relies heavily on a one-to-one
match between Device Tree nodes and media pad links. While this works for
simpler configurations, it causes issues when Device Tree nodes do not
match media pad link logic (e.g., mt9m114). Switch to the
media_entity_get_fwnode_pad helper to verify and retrieve the correct pad
linked to an endpoint, rather than assuming the endpoint ID matches the
pad ID.
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # tegra20, parallel camera
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The av7110_start_feed function contains heavily nested if-statements,
causing excessive indentation and violating code style guidelines.
Refactor the logic inside the DMX_MEMORY_FE case by inverting the
conditional check to break early. Additionally, remove the inner
'if (feed->ts_type & TS_DECODER)' check, as it is redundant since
the outer block already validates this condition.
This reduces the indentation level and cleans up redundant checks
without altering the underlying driver behavior.
Signed-off-by: André Moreira <andrem.33333@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
ipu7_resume() calls pm_runtime_get_sync() before resuming the device.
If the runtime PM resume fails, the usage count remains incremented, but
the error path returns without dropping the reference.
Use pm_runtime_resume_and_get() instead, which balances the usage count
on failure and avoids the leak. Keep returning 0 on error, as resume
callbacks should not propagate failures to the PM core, matching the
behaviour of the ipu6 driver.
Fixes: b7fe4c0019 ("media: staging/ipu7: add Intel IPU7 PCI device driver")
Signed-off-by: Vidhu Sarwal <vidhu.linux@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
ipu7_init_fw_code_region_by_sys() calls pm_runtime_get_sync() before
accessing the firmware code region. If resuming the device fails,
pm_runtime_get_sync() leaves the runtime PM usage count incremented,
but the error path returns without dropping the reference.
Use pm_runtime_resume_and_get() instead, which balances the usage count
automatically on failure and avoids the leak.
The ipu6 driver uses pm_runtime_resume_and_get() in the equivalent
location.
Fixes: b7fe4c0019 ("media: staging/ipu7: add Intel IPU7 PCI device driver")
Signed-off-by: Vidhu Sarwal <vidhu.linux@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Three IE/attribute parsing functions have missing bounds checks.
rtw_get_sec_ie() and rtw_get_wapi_ie() iterate over a raw IE buffer
without verifying that the header bytes (tag + length) are within the
remaining buffer before reading them. Additionally, rtw_get_sec_ie()
compares the 4-byte WPA OUI at cnt+2 without checking that at least
6 bytes remain, and rtw_get_wapi_ie() compares a 4-byte WAPI OUI at
cnt+6 without checking that at least 10 bytes remain.
rtw_get_wps_attr() reads wps_ie[0] and wps_ie+2 unconditionally at
entry, before verifying that wps_ielen is large enough to contain
the 6-byte WPS IE header (element_id + length + 4-byte OUI). Inside
the attribute loop, get_unaligned_be16() is called on attr_ptr and
attr_ptr+2 without checking that 4 bytes remain in the buffer.
Add a cnt+2 bounds check before each loop body in rtw_get_sec_ie()
and rtw_get_wapi_ie(), guard each multi-byte comparison with a minimum
IE length requirement, add a wps_ielen < 6 early return in
rtw_get_wps_attr(), and add a 4-byte bounds check in its inner loop.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-8-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The loop in is_ap_in_tkip() iterates over IEs without verifying that
enough bytes remain before dereferencing the IE header or its payload:
- pIE->element_id and pIE->length are read without checking that
i + sizeof(*pIE) <= ie_length, so a truncated IE at the end of the
buffer causes an OOB read.
- For WLAN_EID_VENDOR_SPECIFIC the code compares pIE->data + 12,
which requires pIE->length >= 16. For WLAN_EID_RSN it compares
pIE->data + 8, requiring pIE->length >= 12. Neither requirement
is checked.
Add the missing IE header and payload bounds checks and guard each
data access with an explicit pIE->length minimum, matching the
pattern established in update_beacon_info().
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-7-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IE parsing loop in OnAssocRsp() advances by (pIE->length + 2) each
iteration but only guards on i < pkt_len. When a malicious AP sends an
AssocResponse whose last IE has only one byte remaining in the frame
(the element_id byte lands at pkt_len-1), the loop reads pIE->length
from pframe[pkt_len], which is one byte past the allocated receive buffer.
Additionally, even when the header bytes are in bounds, pIE->length
itself can extend the data window beyond pkt_len, silently passing a
truncated IE to the handler functions.
Add two guards at the top of the loop body:
1. Break if fewer than sizeof(*pIE) bytes remain (can't read header).
2. Break if the IE's declared data extends past pkt_len.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260522004531.1038924-6-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HT_caps_handler() iterates pIE->length bytes and writes into
HT_caps.u.HT_cap[], which is a fixed 26-byte array (sizeof struct
HT_caps_element). Because pIE->length is a raw u8 from an over-the-air
802.11 AssocResponse frame and is never validated, a malicious AP can
set it up to 255, causing up to 229 bytes of out-of-bounds writes into
adjacent fields of struct mlme_ext_info.
Truncate the iteration count to the size of HT_caps.u.HT_cap using
umin() so that data from a longer-than-expected IE is silently ignored
rather than written out of bounds, preserving interoperability with APs
that pad the element. An early return on oversized IEs was considered
but rejected: it would bypass the pmlmeinfo->HT_caps_enable = 1
assignment that precedes the loop, silently disabling HT mode for APs
that append extra bytes to the HT Capabilities IE.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Link: https://patch.msgid.link/20260522004531.1038924-5-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
supplicant_ie is a 256-byte array in struct security_priv. The WPA and
WPA2 IE copy paths use:
memcpy(padapter->securitypriv.supplicant_ie, &pwpa[0], wpa_ielen + 2);
where wpa_ielen is the raw IE length field (u8, 0-255). When a local user
supplies a connect request via nl80211 with a crafted WPA IE of length 255,
wpa_ielen + 2 equals 257, overflowing the 256-byte buffer by one byte into
the adjacent last_mic_err_time field.
rtw_parse_wpa_ie() does not prevent this: its length consistency check
compares *(wpa_ie+1) against (u8)(wpa_ie_len-2), which is (u8)(255) == 255
when wpa_ie_len = 257, so the check passes silently.
Add explicit bounds checks for both the WPA and WPA2 paths before the
memcpy, rejecting any IE whose total size (wpa_ielen + 2) exceeds the
supplicant_ie buffer.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-4-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two IE parsing loops are missing the header bounds checks before they
dereference pIE->length:
- issue_assocreq() walks pmlmeinfo->network.ies to build the
association request. If the stored IE data ends with only an
element_id byte and no length byte, pIE->length is read one byte
past the end of the buffer.
- join_cmd_hdl() walks pnetwork->ies during station join and has
the same problem under the same conditions.
Both buffers are filled from AP beacon and probe-response frames, so a
malicious AP that sends a truncated final IE can trigger the issue.
Apply the two-guard pattern established in update_beacon_info():
1. Break if fewer than sizeof(*pIE) bytes remain.
2. Break if the IE's declared data extends past the buffer end.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-3-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IE parsing loop in update_beacon_info() advances by
(pIE->length + 2) each iteration but only guards on i < len.
When a malicious AP sends a Beacon whose last IE has only one byte
remaining in the frame (the element_id byte lands at len-1), the loop
reads pIE->length from one byte past the allocated receive buffer.
Additionally, even when the header bytes are in bounds, pIE->length
itself can extend the data window beyond len, passing a truncated IE
to the handler functions.
Add two guards at the top of the loop body:
1. Break if fewer than sizeof(*pIE) bytes remain (can't read header).
2. Break if the IE's declared data extends past len.
Also replace i += (pIE->length + 2) with i += sizeof(*pIE) + pIE->length
for consistency with the sizeof(*pIE) guards added above.
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004531.1038924-2-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OnAuth() has two bugs in the shared-key authentication path.
When the Privacy bit is set, rtw_wep_decrypt() is called without
verifying that the frame is long enough to contain a valid WEP IV and
ICV. Inside rtw_wep_decrypt(), length is computed as:
length = len - WLAN_HDR_A3_LEN - iv_len
and then passed as (length - 4) to crc32_le(). If len is less than
WLAN_HDR_A3_LEN + iv_len + icv_len (32 bytes), length - 4 is negative
and, after the implicit cast to size_t, causes crc32_le() to read far
beyond the frame buffer. Add a minimum length check before accessing
the IV field and calling the decryption path.
When processing a seq=3 response, rtw_get_ie() stores the Challenge
Text IE length in ie_len, but the subsequent memcmp() always reads 128
bytes regardless of ie_len. IEEE 802.11 mandates a challenge text of
exactly 128 bytes; reject any IE whose length field differs, matching
the check already applied to OnAuthClient().
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260522004605.1039209-1-hossu.alexandru@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tsi148_probe() allocates a location monitor resource and links it into
tsi148_bridge->lm_resources. The probe error path frees this list, but
tsi148_remove() only frees the dma, slave and master resource lists, so
the location monitor resource is leaked on device unbind or module
unload.
Free the lm_resources list in tsi148_remove() as well, before
tsi148_bridge is freed.
Fixes: d22b8ed9a3 ("Staging: vme: add Tundra TSI148 VME-PCI Bridge driver")
Cc: stable <stable@kernel.org>
Cc: Martyn Welch <martyn@welchs.me.uk>
Assisted-by: Claude:claude-fable-5
Signed-off-by: Hao-Qun Huang <alvinhuang0603@gmail.com>
Link: https://patch.msgid.link/20260704065817.403111-2-alvinhuang0603@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fake_init() allocates a location monitor resource and links it into
fake_bridge->lm_resources. The init error path frees this list, but
fake_exit() only frees the slave and master resource lists. Loading
and unloading the module therefore triggers a kmemleak warning:
unreferenced object 0xffff8b8b82aebe40 (size 64):
comm "init", pid 1, jiffies 4294894572
backtrace (crc c1e013ef):
kmemleak_alloc+0x4e/0x90
__kmalloc_cache_noprof+0x338/0x430
0xffffffffc0602246
do_one_initcall+0x4f/0x320
do_init_module+0x68/0x270
load_module+0x2a3b/0x2d90
Free the lm_resources list in fake_exit() as well, before fake_bridge
is freed.
Fixes: 658bcdae9c ("vme: Adding Fake VME driver")
Cc: stable <stable@kernel.org>
Cc: Martyn Welch <martyn@welchs.me.uk>
Assisted-by: Claude:claude-fable-5
Signed-off-by: Hao-Qun Huang <alvinhuang0603@gmail.com>
Link: https://patch.msgid.link/20260704065817.403111-1-alvinhuang0603@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SLAVE-path helpers buffer_to_user() and buffer_from_user() copy
'count' bytes into/out of the fixed-size kern_buf (size_buf ==
PCI_BUF_SIZE == 0x20000, 128 KiB) using *ppos as the offset, without
bounding *ppos + count against size_buf.
vme_user_write()/vme_user_read() only clamp count to the VME window size
(image_size = vme_get_size(resource)), which VME_SET_SLAVE sets from the
user-supplied slave.size -- validated against the VME address space (up
to VME_A32_MAX = 4 GiB), not against PCI_BUF_SIZE. When the window
exceeds 128 KiB, a write()/read() copies past the kern_buf allocation.
Clamp count against size_buf in both helpers, with an early return when
*ppos is already at/after the buffer end. *ppos is >= 0 here (the caller
rejects negative offsets), so size_buf - *ppos cannot wrap. This mirrors
the existing clamp in the MASTER-path helpers resource_to_user() /
resource_from_user(), and matches the read()/write() convention of a
short transfer at end-of-buffer.
Found by static analysis (CodeQL taint tracking + CBMC bounded model
checking) and confirmed dynamically under KASAN with the vme_fake bridge:
BUG: KASAN: slab-out-of-bounds in _copy_from_user+0x2d/0x80
Write of size 262144 at addr ffff888004100000 by task trigger/68
_copy_from_user+0x2d/0x80
vme_user_write+0x13e/0x240 [vme_user]
vfs_write+0x1b8/0x7a0
ksys_write+0xb8/0x150
Fixes: f00a86d98a ("Staging: vme: add VME userspace driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Tautschnig <tautschn@amazon.com>
Link: https://patch.msgid.link/20260618114709.72499-1-tautschn@amazon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bc4df274dc ("staging: rtl8723bs: update _rtw_pktfile_read() to
return error codes") changed _rtw_pktfile_read() to fail when the caller
asks for more bytes than remain in the packet:
if (rtw_remainder_len(pfile) < rlen)
return -EINVAL;
That breaks the assumption made by the data TX path. In
rtw_xmitframe_coalesce() (core/rtw_xmit.c) the per-fragment copy is
issued with the full fragment length, mpdu_len, which is derived from
pxmitpriv->frag_len (~2300 bytes), and the code relies on the historical
behaviour of copying only what is left and returning the number of bytes
actually copied:
mem_sz = _rtw_pktfile_read(&pktfile, pframe, mpdu_len);
if (mem_sz < 0)
return mem_sz;
So for every outbound packet smaller than the fragmentation threshold -
i.e. essentially all normal traffic, including the EAPOL frames of the
WPA 4-way handshake and DHCP - rlen is larger than the bytes remaining,
_rtw_pktfile_read() returns -EINVAL, rtw_xmitframe_coalesce() aborts, and
the frame is dropped before it is queued to the hardware. The driver
floods the log with:
rtl8723bs ...: xmit_xmitframes: coalesce failed with error -22
Management frames (authentication/association) use a different path and
still go out, so the interface scans and associates, but no data frame is
ever transmitted. The 4-way handshake therefore never completes and
wpa_supplicant misreports it as:
WPA: 4-Way Handshake failed - pre-shared key may be incorrect
AP mode is unaffected. The net effect is that the chip is unusable in
station mode on any kernel carrying the offending commit.
This was confirmed with a wpa_supplicant -dd trace on an RTL8723BS SDIO
adapter (Bay Trail): message 1/4 is received and the PTK is derived, but
each "Sending EAPOL-Key 2/4" coincides 1:1 with a "coalesce failed with
error -22", so message 2/4 never reaches the AP, which keeps retrying
message 1/4 until the handshake times out.
Restore the original semantics: clamp the requested length to the bytes
remaining in the packet and return that length. The skb_copy_bits()
error path is kept, so genuine copy failures are still propagated.
Fixes: bc4df274dc ("staging: rtl8723bs: update _rtw_pktfile_read() to return error codes")
Cc: stable <stable@kernel.org>
Tested-by: Christopher Mackle <christophermackle01@gmail.com>
Signed-off-by: Christopher Mackle <christophermackle01@gmail.com>
Link: https://patch.msgid.link/20260620013916.7148-1-christophermackle01@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Here is the big set of staging driver updates for 7.2-rc1.
Nothing major in here, just constant grind of tiny cleanups and coding
style fixes and wrapper removals. Overall more code was removed than
added, always a nice sign that things are progressing forward.
Changes outside of drivers/staging/ was due to the octeon driver
changes, which for some reason also lives partially in the mips
subsystem, someday that all will be untangled and cleaned up, or just
removed entirely, it's hard to tell which is going to be its fate.
Other than octeon driver cleanups, in here are the usual:
- rtl8723bs driver reworking and cleanups, being the bulk of this
merge window given all of the issues and wrappers involved in that
beast of a driver.
- most driver cleanups
- sm750fb driver cleanups (which might be done, as this really should
be moved to the drm layer one of these days...)
- other tiny staging driver cleanups and fixes
All of these have been in linux-next for many weeks with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCajk7UA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymqGwCfTWeRfHlodxLtncg/2yLDpb+Z1oEAoMJml/AV
XAdQzdJVI1nOH6w9Qch/
=bqYI
-----END PGP SIGNATURE-----
Merge tag 'staging-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big set of staging driver updates for 7.2-rc1.
Nothing major in here, just constant grind of tiny cleanups and coding
style fixes and wrapper removals. Overall more code was removed than
added, always a nice sign that things are progressing forward.
Changes outside of drivers/staging/ was due to the octeon driver
changes, which for some reason also lives partially in the mips
subsystem, someday that all will be untangled and cleaned up, or just
removed entirely, it's hard to tell which is going to be its fate.
Other than octeon driver cleanups, in here are the usual:
- rtl8723bs driver reworking and cleanups, being the bulk of this
merge window given all of the issues and wrappers involved in that
beast of a driver
- most driver cleanups
- sm750fb driver cleanups (which might be done, as this really should
be moved to the drm layer one of these days...)
- other tiny staging driver cleanups and fixes
All of these have been in linux-next for many weeks with no reported
issues"
* tag 'staging-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (199 commits)
staging: most: video: avoid double free on video register failure
staging: sm750: rename CamelCase variable Bpp to bpp
staging: rtl8723bs: delete superfluous switch statement
staging: sm750fb: Mark g_noaccel, g_nomtrr and g_dualview as __ro_after_init
staging: rtl8723bs: propagate errno through hal xmit path
staging: rtl8723bs: propagate errno through xmit enqueue path
staging: rtl8723bs: convert rtw_xmit_classifier to return errno
staging: rtl8723bs: make rtw_xmit_classifier static
staging: rtl8723bs: simplify rtw_xmit_classifier control flow
staging: rtl8723bs: make _rtw_enqueue_cmd return 0 on success
staging: rtl8723bs: simplify rtw_enqueue_cmd control flow
staging: rtl8723bs: make _rtw_enqueue_cmd static
staging: rtl8723bs: simplify _rtw_enqueue_cmd control flow
staging: rtl8723bs: fix multiple blank lines in more hal/ files
staging: rtl8723bs: remove unused TXDESC_64_BYTES code
staging: rtl8723bs: remove unused DBG_XMIT_BUF and DBG_XMIT_BUF_EXT code
staging: rtl8723bs: fix multiple blank lines in hal/Hal* files
staging: rtl8723bs: fix multiple blank lines in hal/ files
staging: rtl8723bs: rtw_mlme: add blank line for readability
staging: rtl8723bs: rtw_mlme: wrap rtw_sitesurvey_cmd condition
...
Here is the big set of char, misc, iio, fpga, and other small driver
subsystems changes for 7.2-rc1.
Lots of little stuff in here, the majority being of course the IIO
driver updates, as a list they are:
- IIO driver updates and additions
- GPIB driver bugfixes and cleanups
- Android binder driver updates (rust and C version)
- counter driver updates
- MHI driver updates
- mei driver updates
- w1 driver updates
- interconnect driver updates
- Comedi driver fixes and updates
- some obsolete char drivers removed (applicom and dtlk)
- hwtracing driver updates
- other tiny driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCajk4Gg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl89wCdG1WBLsvKHZ3zaFWd4POE8G/gS1YAnRf0GcRB
0F1/iBXSZLaRF/p9dsGq
=fg13
-----END PGP SIGNATURE-----
Merge tag 'char-misc-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc driver updates from Greg KH:
"Here is the big set of char, misc, iio, fpga, and other small driver
subsystems changes for 7.2-rc1.
Lots of little stuff in here, the majority being of course the IIO
driver updates, as a list they are:
- IIO driver updates and additions
- GPIB driver bugfixes and cleanups
- Android binder driver updates (rust and C version)
- counter driver updates
- MHI driver updates
- mei driver updates
- w1 driver updates
- interconnect driver updates
- Comedi driver fixes and updates
- some obsolete char drivers removed (applicom and dtlk)
- hwtracing driver updates
- other tiny driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (406 commits)
w1: ds2482: Use named initializers for arrays of i2c_device_data
firmware: stratix10-svc: Add support to query Arm Trusted Firmware (ATF) version
firmware: stratix10-rsu: avoid blocking reboot_image sysfs when busy
coresight: ultrasoc-smb: Fix OOB write in smb_sync_perf_buffer()
iio: adc: nxp-sar-adc: harden buffer ISR against per-channel read failure
iio: chemical: scd30: Replace manual locking with RAII locking
iio: light: tsl2591: remove unneeded tsl2591_compatible_als_persist_cycle()
iio: dac: ad5686: create bus ops struct
iio: dac: ad5686: cleanup doc header of local structs
iio: dac: ad5686: add control_sync() for single-channel devices
iio: dac: ad5686: add helpers to handle powerdown masks
iio: dac: ad5686: add of_match table to the spi driver
iio: dac: ad5686: drop enum id
iio: dac: ad5686: remove redundant register definition
iio: dac: ad5686: refactor include headers
iio: adc: ad4080: fix AD4880 chip ID
iio: light: veml3328: add support for new device
dt-bindings: iio: light: veml6030: add veml3328
fpga: microchip-spi: fix zero header_size OOB read in mpf_ops_parse_header()
fpga: dfl-afu: validate DMA mapping length in afu_dma_map_region()
...
This has been quite a busy release, mainly due to the subsystem wide
work Johan Hovold has done to modernise resource allocation for the
subsystem on probe, the subsystem did some very clever allocation
management pre devm which didn't quite mesh comfortably with managed
allocations and made it far too easy to introduce error handling and
removal bugs.
- Cleanup and simplification of controller struct allocation, moving
everything over to devm and making the devm APIs more robust, from
Johan Hovold
- Support for spi-mem devices that don't assert chip select and support
for a secondary read command for memory mapped flashes, some commits
for this are shared with mtd.
- Support for SpacemiT K1.
There will be a simple add/add conflict with the i2c-host tree in the
x86 quirk data in drivers/acpi/acpi_apd.c.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmowLx0ACgkQJNaLcl1U
h9BiuAf/bSzTrdeSLpQyQh/UxCKnl4joFtpyb9SValB/32oSTx9YecNYLDxA2z1L
3dkEPBRGBcGjGCINDQldJM/WMMRT0JKG58aWluF3YNPshKN7qK18iNQxbeN9Dh8F
qykmyWZ7wnLks03UCVm7be9kl2UHs4JJ+oRoHq0+6ktS7o+BrIzgJweprmTBmyB4
rRigCbPSL2BNBZnNvWqrZSYeqWHnonGYabhogaSJnhmeJTkSfKE6mugE8qmGzi+O
ZGeWsTdq270WU1omDZRy/PQQ3YLoLU2lUCGuHWTrT/98sGIJjkYV7UfE58GJwzpi
d1N+y8unL0R5HgSkMM4B+f/4OL3VoA==
=1zbv
-----END PGP SIGNATURE-----
Merge tag 'spi-v7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This has been quite a busy release, mainly due to the subsystem wide
work Johan Hovold has done to modernise resource allocation for the
subsystem on probe, the subsystem did some very clever allocation
management pre devm which didn't quite mesh comfortably with managed
allocations and made it far too easy to introduce error handling and
removal bugs.
- Cleanup and simplification of controller struct allocation, moving
everything over to devm and making the devm APIs more robust, from
Johan Hovold
- Support for spi-mem devices that don't assert chip select and
support for a secondary read command for memory mapped flashes,
some commits for this are shared with mtd.
- Support for SpacemiT K1"
* tag 'spi-v7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (118 commits)
spi: Fix mismatched DT property access types
spi: xilinx: use FIFO occupancy register to determine buffer size
spi: spi-mem: Fix spi_controller_mem_ops kdoc
spi: xilinx: let transfers timeout in case of no IRQ
spi: dt-bindings: nuvoton,npcm750-fiu: Convert to DT schema
spi: meson-spifc: fix runtime PM leak on remove
spi: Use named initializers for platform_device_id arrays
spi: rzv2h-rspi: Add suspend/resume support
spi: dw-pci: remove redundant pci_free_irq_vectors() calls
spi: ep93xx: fix double-free of zeropage on DMA setup failure
spi: cadence-xspi: Revert COMPILE_TEST support
spi: cadence-xspi: Support 32bit and 64bit slave dma interface
spi: tegra210-quad: Allocate DMA memory for DMA engine
spi: imx: replace dmaengine_terminate_all() with dmaengine_terminate_sync()
spi: fsl-lpspi: terminate the RX channel on TX prepare failure path
spi: fsl-lpspi: replace dmaengine_terminate_all() with dmaengine_terminate_sync()
spi: atmel: fix DMA channel and bounce buffer leaks
spi: omap2-mcspi: Use of_device_get_match_data()
spi: Use named initializers for arrays of i2c_device_data
spi: aspeed: Replace VLA parameter with flat pointer in calibration helper
...
GPIO core:
- Add an initial set of kunit test cases for the GPIO subsystem
- Use the devres owner as the GPIO chip's parent in absence of any other
parent
- Fix const-correctness of GPIO chip SRCU guards
- Provide new GPIO consumer interfaces: gpiod_is_single_ended() and
fwnode_gpiod_get()
- Quarantine all legacy GPIO APIs in linux/gpio/legacy.h
- Use __ro_after_init where applicable
New drivers:
- Add driver for the GPIO controller on Waveshare DSI TOUCH panels
Removed drivers:
- Remove the obsolete ts5500 GPIO driver
Driver updates:
- Modernize gpio-timberdale: remove platform data support and use generic
device property accessors
- Extend test build coverage by enabling COMPILE_TEST for more GPIO
drivers
- Add some missing dependencies in Kconfig
- Add support for sparse fixed direction to gpio-regmap
- Remove dead code from gpio-nomadik
- use BIT() in gpio-mxc
- use bitmap_complement() in gpio-xilinx and gpio-pca953x
- Use more appropriate printing functions where applicable
- Use named initializers for platform_device_id and i2c_device_id arrays
- Convert gpio-altera to using the generic GPIO chip helper library
- Add support for new models to gpio-dwapb, gpio-zynq, gpio-usbio and
gpio-tegra186
- Unify the naming convention for Qualcomm in GPIO drivers
- Fix interrupt bank mapping to GPIO chips in gpio-mt7621
- Add support for the lines-initial-states property to gpio-74x164
- Switch to using dynamic GPIO base in gpio-ixp4xx
- Move the handling of an OF quirk from ASoC to gpiolib-of.c where other
such quirks live
- Use handle_bad_irq() in gpio-ep93xx
- Some other minor tweaks and refactorings
Devicetree bindings:
- Document the Waveshare GPIO controller for DSI TOUCH panels
- Document new models: Tegra238 in gpio-tegra186 and EIO GPIO in gpio-zynq
- Add new properties for gpio-dwapb and fairchild,74hc595
- Fix whitespace issues
- Sort compatibles alphabetically in gpio-zynq
Documentation:
- Fix kerneldoc warnings in gpio-realtek-otto
Misc:
- Attach software nodes representing GPIO chips to the actual struct
device objects associated with them in some legacy platforms enabling
real firmware node lookup instead of string matching
- Drop unneeded dependencies on OF_GPIO from bus and staging drivers
-----BEGIN PGP SIGNATURE-----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=MzJz
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There's one new driver, one legacy driver removed, a kunit test-suite
for the GPIO core, support for new models in existing drivers and a
slew of various changes in many places though I can't think of
anything controversial that would stand out - it's been a relatively
calm cycle.
GPIO core:
- Add an initial set of kunit test cases for the GPIO subsystem
- Use the devres owner as the GPIO chip's parent in absence of any
other parent
- Fix const-correctness of GPIO chip SRCU guards
- Provide new GPIO consumer interfaces: gpiod_is_single_ended() and
fwnode_gpiod_get()
- Quarantine all legacy GPIO APIs in linux/gpio/legacy.h
- Use __ro_after_init where applicable
New drivers:
- Add driver for the GPIO controller on Waveshare DSI TOUCH panels
Removed drivers:
- Remove the obsolete ts5500 GPIO driver
Driver updates:
- Modernize gpio-timberdale: remove platform data support and use
generic device property accessors
- Extend test build coverage by enabling COMPILE_TEST for more GPIO
drivers
- Add some missing dependencies in Kconfig
- Add support for sparse fixed direction to gpio-regmap
- Remove dead code from gpio-nomadik
- use BIT() in gpio-mxc
- use bitmap_complement() in gpio-xilinx and gpio-pca953x
- Use more appropriate printing functions where applicable
- Use named initializers for platform_device_id and i2c_device_id
arrays
- Convert gpio-altera to using the generic GPIO chip helper library
- Add support for new models to gpio-dwapb, gpio-zynq, gpio-usbio and
gpio-tegra186
- Unify the naming convention for Qualcomm in GPIO drivers
- Fix interrupt bank mapping to GPIO chips in gpio-mt7621
- Add support for the lines-initial-states property to gpio-74x164
- Switch to using dynamic GPIO base in gpio-ixp4xx
- Move the handling of an OF quirk from ASoC to gpiolib-of.c where
other such quirks live
- Use handle_bad_irq() in gpio-ep93xx
- Some other minor tweaks and refactorings
Devicetree bindings:
- Document the Waveshare GPIO controller for DSI TOUCH panels
- Document new models: Tegra238 in gpio-tegra186 and EIO GPIO in
gpio-zynq
- Add new properties for gpio-dwapb and fairchild,74hc595
- Fix whitespace issues
- Sort compatibles alphabetically in gpio-zynq
Documentation:
- Fix kerneldoc warnings in gpio-realtek-otto
Misc:
- Attach software nodes representing GPIO chips to the actual struct
device objects associated with them in some legacy platforms
enabling real firmware node lookup instead of string matching
- Drop unneeded dependencies on OF_GPIO from bus and staging drivers"
* tag 'gpio-updates-for-v7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (62 commits)
gpio: nomadik: remove dead DB8540 code from <gpio/gpio-nomadik.h>
gpio: mt7621: fix interrupt banks mapping on gpio chips
bus: ts-nbus: drop unneeded dependency on OF_GPIO
staging: media: max96712: drop unneeded dependency on OF_GPIO
gpiolib: Replace strcpy() with memcpy()
gpio: remove obsolete UAF FIXMEs from lookup paths
gpio: core: fix const-correctness of gpio_chip_guard
gpio: mxc: use BIT() macro
gpio: realtek-otto: fix kernel-doc warnings
gpio: max77620: Unify usage of space and comma in platform_device_id array
gpio: Use named initializers for platform_device_id arrays
gpio: cros-ec: Drop unused assignment of platform_device_id driver data
ARM: omap1: enable real software node lookup of GPIOs on Nokia 770
ARM: omap1: use platform_device_register_full() for GPIO devices on OMAP 16xx
ARM: omap1: drop unused variable from omap16xx_gpio_init()
gpio: gpiolib: use seq_puts() for plain strings
gpio: ts5500: remove obsolete driver
gpio: add kunit test cases for the GPIO subsystem
kunit: provide kunit_platform_device_unregister()
kunit: provide kunit_platform_device_register_full()
...
Here are two small bugfixes for a staging driver to fix a
much-reported issue. The fixes are for the rtl8723bs driver and it's
something that many scanning tools keep tripping over in convoluted ways
(and seems to be able to be triggered by network traffic.) These fixes
have been in linux-next for many weeks with no reported issues, sorry
for the delay in getting them to you.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaivZug8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykZ3gCfYVW4wCYm4ZpkkYly3bO75AMaFmIAoMfIB0qD
tUDe4wHd9gPN2JYTJfxf
=zdW9
-----END PGP SIGNATURE-----
Merge tag 'staging-7.1-final' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are two small bugfixes for a staging driver to fix a
much-reported issue.
The fixes are for the rtl8723bs driver and it's something that many
scanning tools keep tripping over in convoluted ways (and seems to be
able to be triggered by network traffic)
These fixes have been in linux-next for many weeks with no reported
issues, sorry for the delay in getting them to you"
* tag 'staging-7.1-final' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8723bs: rtw_mlme: add bounds checks before ie_length subtraction
staging: rtl8723bs: fix buffer over-read in rtw_update_protection
OF_GPIO is selected automatically on all OF systems. Any symbols it
controls also provide stubs and are private to GPIOLIB anyway so there's
really no reason to select it explicitly.
Link: https://patch.msgid.link/20260506082211.5624-1-bartosz.golaszewski@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Stepan Ionichev <sozdayvek@gmail.com>
Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The device powers up in I2C mode. Switching to SPI mode
requires sending a sequence of SPI writes as described in
the datasheet.
During this sequence, the device may still be in I2C mode,
so SPI transactions may not be recognized and can fail.
Such errors are therefore ignored.
Add a comment to clarify this behavior.
Datasheet: https://www.analog.com/en/products/adt7316.html
Reviewed-by: Maxwell Doose <m32285159@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Hungyu Lin <dennylin0707@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Two comments incorrectly refer to 'AD9843' instead of 'AD9834'.
Fix the copy-paste typo.
Signed-off-by: Angus Gardner <angusg778@gmail.com>
Reviewed-by: Maxwell Doose <m32285159@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace open-coded dev_err() + return sequences with dev_err_probe(),
which is the preferred pattern for probe error paths as it handles
deferred probing correctly and reduces boilerplate.
Convert all three remaining instances in ad9834_probe():
- master clock enable failure
- device init SPI sync failure
The avdd regulator path already used dev_err_probe().
Signed-off-by: Angus Gardner <angusg778@gmail.com>
Reviewed-by: Maxwell Doose <m32285159@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
