Use the triggered buffer helper functions to setup and tear down the buffer for
the adis16400 instead of doing this manually. This also means that we switch
away from the deprecated sw_ring buffer and use the kfifo buffer now instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the new adis library for the adis16400 driver. This allows us to completely
scrap the adis16400 trigger code and more than half of the core driver code. For
now we can not make use of the generic adis buffer implementation since the
adis16400 driver has special requirements due to its burst mode support. But
we will eventually get to this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The chip_info struct for contains a defaul_scan_mask field. But it is never
actually used in the code, so remove it from the chip_info struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The 3db divisors table is partially wrong and incomplete. Also the code rounds
up to the next higher frequency if the requested frequency would matches one of
the available frequencies. These two issues are fixed by this patch. The patch
also changes the driver to round down the filter frequency if it is larger than
the largest supported frequency instead of rejecting it as an invalid value.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ilog2 is not defined for 0, so we need to handle the case where the requested
frequency is larger than the base sampling rate. In this case we'll round down
and set the sampling rate to the base sampling rate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The tsl2x7x driver has a copy'n'pasted version of the iio_str_to_fixedpoint()
function from the IIO core. Replace this custom copy and use
iio_str_to_fixedpoint instead.
The patch also introduces a slight functional change in that it makes sure that
in case of a parsing error the error is reported back to userspace instead of
silently ignoring it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jon Brenner <jon.brenner@ams.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch implements support for sampling of a touchscreen into
the MXS LRADC driver. The LRADC block allows configuring some of
it's channels into special mode where they either output the drive
voltage or sample it, allowing it to operate a 4-wire or 5-wire
resistive touchscreen.
In case the touchscreen mode is enabled, the LRADC slot #7 is
reserved for touchscreen only, therefore it is not possible to
sample 8 LRADC channels at time, but only 7 channels.
The touchscreen controller is configured such that the PENDOWN event
disables touchscreen interrupts and triggers execution of worker
thread, which then polls the touchscreen controller for X, Y and
Pressure values. This reduces the overhead of interrupt-driven
operation. Upon the PENUP event, the worker thread re-enables the
PENDOWN detection interrupt and exits.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit a301d425e ("staging:iio:gyro remove adis16251 driver as now supported by
adis16260 driver") removed the adis16251, but left its Makefile entry intact.
This patch removes the unused Makefile entry.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ERROR: "iio_triggered_buffer_setup" [drivers/iio/adc/max1363.ko] undefined!
ERROR: "iio_triggered_buffer_cleanup" [drivers/iio/adc/max1363.ko] undefined!
add select IIO_TRIGGERED_BUFFER
IIO_TRIGGERED_BUFFER in turn selects IIO_TRIGGER and IIO_KFIFO_BUF, so drop those
MAX1363_RING_BUFFER is not used anymore
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch allows the board code to define SPI devices which needs to
toggle the chip select after every word send. This is needed to get a
better resolution reading e.g. an ADC data stream.
Apart from that, as in the normal code CS is controlled by software,
a transfer is done much faster.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes some indentation errors.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct value for minimal voltage for ldo10 output is 950000 uV. This
patch fixes the typo introduced by patch adf6178ad5
("regulator: max8998: Use uV in voltage_map_desc"), what solves broken
probe of max8998 in v3.8-rc4.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the HWMOD_BLOCK_WFI flag in the hwmod data to prevent the MPU from
entering WFI when the I2C devices are active. No idea why this is needed;
this could certainly bear further investigation if anyone is interested.
The objective here is to remove some custom code from the OMAP24xx PM
code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Apparently, on some OMAPs, the MPU can't be allowed to enter WFI while
certain peripherals are active. It's not clear why, and it's likely
that there is simply some other bug in the driver or integration code.
But since the likelihood that anyone will have the time to track these
problems down in the future seems quite small, we'll provide a
flag, HWMOD_BLOCK_WFI, to mark these issues in the hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Just a few small things:
- 2x workaround bits from Chris to fix up the new scanline waits enabled
in 3.8 on snb. People who've been struck by this on dual-screen also
need to upgrade the ddx.
- Dump the kernel version into i915_error_state, we've had a few mixups
there recently.
- Disable gfx DMAR on gen4 devices, acked by David Woodhouse.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: dump UTS_RELEASE into the error_state
iommu/intel: disable DMAR for g4x integrated gfx
drm/i915: GFX_MODE Flush TLB Invalidate Mode must be '1' for scanline waits
drm/i915: Disable AsyncFlip performance optimisations
The OMAP3xxx CPUIdle driver contains some code to place a lower bound
on the PER powerdomain's power state. Convert this code to a data-driven
implementation to remove branches and to improve readability.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Add the possible logic retention states for the 24xx CORE powerdomain.
Subsequent patches use this data to avoid returning incorrect data, by
skipping reads from register bitfields that don't actually exist.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove some clocks that don't appear to be used by anything
and which are not associated with any hardware registers.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Convert all DEFINE_OMAP_MUX_GATE() combinations that list MODULEMODE
registers in their gate arguments to DEFINE_OMAP_MUX(), dropping the
MODULEMODE data. This is possible because the MODULEMODE bits control
IP blocks, not clocks; and the hwmod code takes care of IP block
control. Rename these clocks to reflect the original multiplexer name
as specified in the comments. And convert the hwmod data to use the
multiplexer clock name.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Remove some leaf "clocks" that are actually IP block idle control
points, since these should now be handled by the hwmod code.
There are still a few types of MODULEMODE clocks that need to be
cleaned up:
- those still in use by driver or integration code
- those in DEFINE_CLK_OMAP_MUX_GATE() blocks; the gate portion of
these should be removed
A similar process may also be possible on OMAP2/3.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Remove now-obsolete code from arch/arm/mach-omap2/omap_device.c. This
mostly consists of removing the first attempt at device PM latency
handling. This was never really used, has been replaced by the common
dev_pm_qos code, and needs to go away as part of the DT conversion.
Also, the early platform_device creation code has been removed, as it
appears to be unused.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
regulator_register() does not return NULL, it returns ERR_PTR on error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There were missing break statements so everything used
TWO_CHANNEL_SUPPORT.
Also I added a return statement to silence a GCC warning:
sound/soc/dwc/designware_i2s.c: In function ‘dw_i2s_hw_params’:
sound/soc/dwc/designware_i2s.c:236:32: warning: ‘ch_reg’ may be
used uninitialized in this function
[-Wmaybe-uninitialized]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bindings assumed that the gpios properties were always there, which
made the NO_TX and NO_RX mode not usable from device tree. Add extra
checks to make sure that the driver can work if either MOSI or MISO is
not used.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Building for the snowball board, I ran into this compile failure:
CC drivers/regulator/dbx500-prcmu.o
arm-test.git/drivers/regulator/dbx500-prcmu.c:119:11: error: 'THIS_MODULE' undeclared here (not in a function)
make[3]: *** [drivers/regulator/dbx500-prcmu.o] Error 1
make[2]: *** [drivers/regulator] Error 2
Commit 38e968380 "regulators/db8500: split off shared dbx500 code"
separated out the dbx500 code but did not copy over the required include
to linux/module.h.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I2S module need to be reset after S2R. Keeping the S/W rst
control part in resume didn't help in playing audio after resume.
So this patch adds S/W RST control part in startup function which
gets triggered for every new audio stream playback.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: R. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare() respectively in order to support the common clk
framework. Otherwise we get warnings on the console as the clock is not
prepared before it is enabled.
In addition we must cache the maximum clock rate to drv_data->max_clk_rate
at probe time because clk_get_rate() cannot be called in tasklet context.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SPI core provides infrastructure for standard message queueing so use
that instead of handling everything in the driver. This simplifies the
driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix following warnings seen when compiling 64-bit:
drivers/spi/spi-pxa2xx.c: In function ‘map_dma_buffers’: drivers/spi/spi-pxa2xx.c:384:7: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:384:40: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c: In function ‘pxa2xx_spi_probe’:
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/spi/spi-pxa2xx.c:1572:27: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We are going to use it on 64-bit kernel on Intel Lynxpoint so make sure we
can build it into such kernel.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The CFA-10037 is another expansion board for the CFA-10036 module, with
only a USB Host, a Ethernet device and a lot of gpios.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
SENSORS_LIMIT and clamp_val have the same functionality, so retire SENSORS_LIMIT
as it is no longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
SENSORS_LIMIT and clamp_val have the same functionality, so retire SENSORS_LIMIT
as it is no longer needed.
The change reduces text size by 26 bytes and bss size by 16 bytes on x86_86
builds.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
SENSORS_LIMIT and the generic clamp_val have the same functionality,
and clamp_val is more efficient.
This patch reduces text size by 9052 bytes and bss size by 11624 bytes
for x86_64 builds.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch renames the supply_uV* variables to supply_uv* to avoid
CamelCase as warned by the checkpatch.pl script.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
__this_cpu_inc_return() or __this_cpu_dec generates a single instruction,
which is faster than __get_cpu_var operation.
Link: http://lkml.kernel.org/r/50A9C1BD.1060308@gmail.com
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In short, it is illegal to call __pa() on an address holding
a percpu variable. This replaces those __pa() calls with
slow_virt_to_phys(). All of the cases in this patch are
in boot time (or CPU hotplug time at worst) code, so the
slow pagetable walking in slow_virt_to_phys() is not expected
to have a performance impact.
The times when this actually matters are pretty obscure
(certain 32-bit NUMA systems), but it _does_ happen. It is
important to keep KVM guests working on these systems because
the real hardware is getting harder and harder to find.
This bug manifested first by me seeing a plain hang at boot
after this message:
CPU 0 irqstacks, hard=f3018000 soft=f301a000
or, sometimes, it would actually make it out to the console:
[ 0.000000] BUG: unable to handle kernel paging request at ffffffff
I eventually traced it down to the KVM async pagefault code.
This can be worked around by disabling that code either at
compile-time, or on the kernel command-line.
The kvm async pagefault code was injecting page faults in
to the guest which the guest misinterpreted because its
"reason" was not being properly sent from the host.
The guest passes a physical address of an per-cpu async page
fault structure via an MSR to the host. Since __pa() is
broken on percpu data, the physical address it sent was
bascially bogus and the host went scribbling on random data.
The guest never saw the real reason for the page fault (it
was injected by the host), assumed that the kernel had taken
a _real_ page fault, and panic()'d. The behavior varied,
though, depending on what got corrupted by the bad write.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130122212435.4905663F@kernel.stglabs.ibm.com
Acked-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This is necessary because __pa() does not work on some kinds of
memory, like vmalloc() or the alloc_remap() areas on 32-bit
NUMA systems. We have some functions to do conversions _like_
this in the vmalloc() code (like vmalloc_to_page()), but they
do not work on sizes other than 4k pages. We would potentially
need to be able to handle all the page sizes that we use for
the kernel linear mapping (4k, 2M, 1G).
In practice, on 32-bit NUMA systems, the percpu areas get stuck
in the alloc_remap() area. Any __pa() call on them will break
and basically return garbage.
This patch introduces a new function slow_virt_to_phys(), which
walks the kernel page tables on x86 and should do precisely
the same logical thing as __pa(), but actually work on a wider
range of memory. It should work on the normal linear mapping,
vmalloc(), kmap(), etc...
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130122212433.4D1FCA62@kernel.stglabs.ibm.com
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
try_preserve_large_page() can be slightly simplified by using
the new page_level_*() helpers. This also moves the 'level'
over to the new pg_level enum type.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130122212432.14F3D993@kernel.stglabs.ibm.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
I plan to use lookup_address() to walk the kernel pagetables
in a later patch. It returns a "pte" and the level in the
pagetables where the "pte" was found. The level is just an
enum and needs to be converted to a useful value in order to
do address calculations with it. These helpers will be used
in at least two places.
This also gives the anonymous enum a real name so that no one
gets confused about what they should be passing in to these
helpers.
"PTE_SHIFT" was chosen for naming consistency with the other
pagetable levels (PGD/PUD/PMD_SHIFT).
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130122212431.405D3A8C@kernel.stglabs.ibm.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The KVM code has some repeated bugs in it around use of __pa() on
per-cpu data. Those data are not in an area on which using
__pa() is valid. However, they are also called early enough in
boot that __vmalloc_start_set is not set, and thus the
CONFIG_DEBUG_VIRTUAL debugging does not catch them.
This adds a check to also verify __pa() calls against max_low_pfn,
which we can use earler in boot than is_vmalloc_addr(). However,
if we are super-early in boot, max_low_pfn=0 and this will trip
on every call, so also make sure that max_low_pfn is set before
we try to use it.
With this patch applied, CONFIG_DEBUG_VIRTUAL will actually
catch the bug I was chasing (and fix later in this series).
I'd love to find a generic way so that any __pa() call on percpu
areas could do a BUG_ON(), but there don't appear to be any nice
and easy ways to check if an address is a percpu one. Anybody
have ideas on a way to do this?
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130122212430.F46F8159@kernel.stglabs.ibm.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRAuO3AAoJEHm+PkMAQRiGbfAH/1C3QQKB11aBpYLAw7qijAze
yOui26UCnwRryxsO8zBCQjGoByy5DvY/Q0zyUCWUE6nf/JFSoKGUHzfJ1ATyzGll
3vENP6Fnmq0Hgc4t8/gXtXrZ1k/c43cYA2XEhDnEsJlFNmNj2wCQQj9njTNn2cl1
k6XhZ9U1V2hGYpLL5bmsZiLVI6dIpkCVw8d4GZ8BKxSLUacVKMS7ml2kZqxBTMgt
AF6T2SPagBBxxNq8q87x4b7vyHYchZmk+9tAV8UMs1ecimasLK8vrRAJvkXXaH1t
xgtR0sfIp5raEjoFYswCK+cf5NEusLZDKOEvoABFfEgL4/RKFZ8w7MMsmG8m0rk=
=m68Y
-----END PGP SIGNATURE-----
Merge tag 'v3.8-rc5' into x86/mm
The __pa() fixup series that follows touches KVM code that is not
present in the existing branch based on v3.7-rc5, so merge in the
current upstream from Linus.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The variable "str" is used as both the source and destination in
function snprintf(), which is undefined behavior based on C11. The
original description in C11 is:
"If copying takes place between objects that
overlap, the behavior is undefined."
And, the function of ceph_osdmap_state_str() is to return the osdmap
state, so it should return "doesn't exist" when all the conditions
are not satisfied. I fix it in this patch.
[elder@inktank.com: shortened the commit message]
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Reviewed-by: Alex Elder <elder@inktank.com>
This boolean function simply returns whether or not the runtime
status of the device is 'active'. The typical scenario is driver
calls pm_runtime_get firstly, then check pm_runtime_active in
atomic environment.
Also add entry to Documentation/power/runtime.txt
Signed-off-by: Yanmin Zhang <yanmin.zhang@intel.com>
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
