The MST link BW reported by branch devices via the ENUM_PATH_RESOURCES
message depends on the channel coding and link rate/lane count
parameters programmed to DPCD. This is the case at least for some branch
devices, while for others the reported BW is independent of the link
parameters. In any case the DP standard requires the branch device to
adjust the returned value to both account for the different way the BW
for FEC is accounted for (included in the returned value for non-UHBR
and not included for UHBR rates) and to limit the returned value to the
(trained) link BW between the source and first downstream branch
device, see DP v2.0/v2.1 Figure 2-94, DP v2.1 5.9.7. Presumedly this is
also the reason why the standard requires the DPCD link rate/lane count
values being up-to-date before sending the ENUM_PATH_RESOURCES message,
see DP v2.1 2.14.9.4.
Based on the above reprobe the MST topology after the link is retrained
with new link parameters to make sure that the MST link BW tracked in
the MST topology state (via each topology port's full_pbn value) is
up-to-date.
The next patch will make sure that the MST link BW is also kept
up-to-date if the link is disabled.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-13-imre.deak@intel.com
If the MST payload allocation failed, enabling the output also failed
most probably, so send a uevent accordinly requesting the user to retry
the modeset. While at it remove the driver specific debug message, there
is already one printed by drm_dp_add_payload_part1().
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-12-imre.deak@intel.com
The MST topology probing depends on the maximum link parameters -
programmed to DPCD if required by a follow-up patch - so make sure these
parameters are up-to-date before configuring and probing the MST
topology.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-11-imre.deak@intel.com
On MST links - at least for some MST branch devices - the list of modes
returned to users on an enabled link depends on the current link
rate/lane count parameters (besides the DPRX link capabilities, any MST
branch BW limit and the maximum link parameters reduced after LT
failures). In particular the MST branch BW limit may depend on the link
rate/lane count parameters programmed to DPCD. After an LT failure and
limiting the maximum link parameters accordingly, users should see a
mode list reflecting these new limits. However with the current fallback
order this isn't ensured, as the new limit could allow for modes
requiring a higher link BW, but these modes will be filtered out due to
the enabled link's lower link BW.
Ensure that the mode list changes in a consistent way after a link
training failure and reducing the link parameters by changing the
fallback order on MST links to happen in BW order.
v2:
- s/INTEL_DP_MAX_SUPPORTED_LANE_COUNTS/INTEL_DP_MAX_SUPPORTED_LANE_CONFIGS
and s/num_common_lane_counts/num_common_lane_configs to make the
difference wrt. max lane counts clearer. (Suraj)
- Add a TODO comment to make the SST fallback logic work the same way as
MST. (Arun)
- Use sort_r()'s default swap function instead of a custom one.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729144458.2763667-1-imre.deak@intel.com
There are multiple failure cases a modeset-retry uevent can be sent for
a link (TBT tunnel BW allocation failure, unrecoverable link training
failure), a follow-up patch adding the handling for a new case where the
DP MST payload allocation fails. The uevent is the same in all cases,
sent to all the connectors on the link, so in case of multiple failures
there is no point in sending a separate uevent for each failure; prevent
this, sending only a single modeset-retry uevent for a commit.
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-7-imre.deak@intel.com
Initialize the DP link parameters during HW readout. These need to be
up-to-date at least for the MST topology probing, which depends on the
link rate and lane count programmed in DPCD. A follow-up patch will
program the DPCD values to reflect the maximum link parameters before
the first MST topology probing, but should do so only if the link is
disabled (link_trained==false).
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-6-imre.deak@intel.com
If the DDI encoder output is enabled in HDMI mode there is no point in
calling intel_dp_sync_state(), as in that case the DPCD initialization
will fail - as expected - with AUX timeouts. Prevent calling the hook in
this case.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-5-imre.deak@intel.com
In the
if (old_ddps != port->ddps || !created)
if (port->ddps && !port->input)
ret = drm_dp_send_enum_path_resources();
sequence the first if's condition is true if the port exists already
(!created) or the port was created anew (hence old_ddps==0) and it was
in the plugged state (port->ddps==1). The second if's condition is true
for output ports in the plugged state. So the function is called for an
output port in the plugged state, regardless if it already existed or
not and regardless of the old plugged state. In all other cases
port->full_pbn can be zeroed as the port is either an input for which
full_pbn is never set, or an output in the unplugged state for which
full_pbn was already zeroed previously or the port was just created
(with port->full_pbn==0).
Simplify the condition, making it clear that the path resources are
always enumerated for an output port in the plugged state.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-4-imre.deak@intel.com
Add stdout-path to the fast models(FVP and Foundation) devicetrees to
specify the primary console. This means that distributions can boot
without the need for platform-specific command line parameters i.e.
they can use earlycon with no parameters and no console argument is
needed at all.
Signed-off-by: Debbie Martin <Debbie.Martin@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Message-Id: <20240730103758.907950-1-Debbie.Martin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
shuffle few fields to reduce the holes within nvme_ns_head.
On x86_64, the size is reduced to 1104 bytes from 1120 bytes.
Signed-off-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
u8 fits the need, so stop using int for it.
Signed-off-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
pi_offset field is not required to be present in nvme_ns_head.
Signed-off-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
The fujitsu,mb85rs256 is a 256 Kbit SPI memory FRAM in the same family
as the two existing fujitsu,mb85rs* compatibles and at25 compatible.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240612092934.12282-1-francesco@dolcini.it
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Since __va(0) does not translate to NULL anymore remove RELOC_HIDE()
which was only added to get rid of a compile warning with clang W=1:
arch/s390/mm/vmem.c:666:36: warning: performing pointer arithmetic on
a null pointer has undefined behavior [-Wnull-pointer-arithmetic]
666 | __set_memory_4k(__va(0), __va(0) + ident_map_size);
| ~~~~~~~ ^
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Use the sort() from lib/sort.c to sort markers instead of the private
implementation. The current implementation does not sort markers
properly if they have to be moved downwards:
---[ Real Memory Copy Area Start ]---
0x0000035b903ff000-0x0000035b90400000 4K PTE I
---[ vmalloc Area Start ]---
---[ Real Memory Copy Area End ]---
Add a new member to each marker which indicates if a marker is start
of an area. If addresses of areas are equal consider an address which
defines the start of an area higher than the address which defines the
end of an area. In result the output is sorted as intended:
---[ Real Memory Copy Area Start ]---
0x0000019cedcff000-0x0000019cedd00000 4K PTE I
---[ Real Memory Copy Area End ]---
---[ vmalloc Area Start ]---
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The page table dumper contains a hard coded assumption that the first
mapped area starts at address zero. With a relocated lowcore this is
not true anymore. Subsequently the first entry (lowcore) is printed as
if it would contain everything from address zero until the end of the
location of the lowcore area.
Fix this by adding a single "Kernel Virtual Address Space" entry,
which always starts at address zero. It ends when the lowcore area
starts which is either address zero, or its relocated address.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Since virtual and real addresses are not the same anymore the
assumption that the kernel image is contained within the identity
mapping is also not true anymore.
Fix this by adding two explicit areas and at the correct locations: one
for the 8kb lowcore area, and one for the identity mapping.
Fixes: c98d2ecae0 ("s390/mm: Uncouple physical vs virtual address spaces")
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
With ARCH=s390, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/s390/cio/ccwgroup.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/s390/cio/vfio_ccw.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240715-md-s390-drivers-s390-cio-v2-1-97eaa6971124@quicinc.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Remove the unused and empty arch/s390/kernel/alternative.h header
file which was added by mistake.
Fixes: 5ade5be4ed ("s390: Add infrastructure to patch lowcore accesses")
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
With the recent rewrite of the fpu code exception handling for the
lfpc instruction within load_fpu_state() was erroneously removed.
Add it again to prevent that loading invalid floating point register
values cause an unhandled specification exception.
Fixes: 8c09871a95 ("s390/fpu: limit save and restore to used registers")
Cc: stable@vger.kernel.org
Reported-by: Aristeu Rozanski <aris@redhat.com>
Tested-by: Aristeu Rozanski <aris@redhat.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
USB-audio driver puts SNDRV_CHMAP_SL and _SR as left and right
surround channels for UAC1 channel map, respectively. But they should
have been SNDRV_CHMAP_RL and _RR; the current value *_SL and _SR are
rather "side" channels, not "surround". I guess I took those
mistakenly when I read the spec mentioning "surround left".
This patch corrects those entries to be the right channels.
Suggested-by: Sylvain BERTRAND <sylvain.bertrand@legeek.net>
Closes: https://lore.kernel.orgZ/qIyJD8lhd8hFhlC@freedom
Fixes: 04324ccc75 ("ALSA: usb-audio: add channel map support")
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20240731142018.24750-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add TMU PCLK clock in CMU_PERI unit. It acts simultaneously as an
interface clock (to access TMU registers) and an operating clock which
makes TMU IP-core functional.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240723163311.28654-2-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Add a constant for TMU PCLK clock. It acts simultaneously as an
interface clock (to access TMU registers) and an operating clock which
makes TMU IP-core functional.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240723163311.28654-1-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
NAU8822 codec PLL parameters are not an information that the general
user should care about, this print is supposed to be used for debugging,
adjust the debug print priority accordingly.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20240731114828.61238-1-francesco@dolcini.it
Signed-off-by: Mark Brown <broonie@kernel.org>
Support "Pre-multiplied" and "None" blend mode on MediaTek's chips by
adding correct blend mode property when the planes init.
Before this patch, only the "Coverage" mode (default) is supported.
For more information, there are three pixel blend modes in DRM driver:
"None", "Pre-multiplied", and "Coverage".
To understand the difference between these modes, let's take a look at
the following two approaches to do alpha blending:
1. Straight:
dst.RGB = src.RGB * src.A + dst.RGB * (1 - src.A)
This is straightforward and easy to understand, when the source layer is
compositing with the destination layer, it's alpha will affect the
result. This is also known as "post-multiplied", or "Coverage" mode.
2. Pre-multiplied:
dst.RGB = src.RGB + dst.RGB * (1 - src.A)
Since the source RGB have already multiplied its alpha, only destination
RGB need to multiply it. This is the "Pre-multiplied" mode in DRM.
For the "None" blend mode in DRM, it means the pixel alpha is ignored
when compositing the layers, only the constant alpha for the composited
layer will take effects.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240717-alpha-blending-v4-5-4b1c806c0749@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Support "Pre-multiplied" alpha blending mode in Mixer.
Before this patch, only the coverage mode is supported.
To replace the default setting that is set in mtk_ethdr_config(),
we change mtk_ddp_write_mask() to mtk_ddp_write(), and this change will
also reset the NON_PREMULTI_SOURCE bit that was assigned in
mtk_ethdr_config(). Therefore, we must still set NON_PREMULTI_SOURCE bit
if the blend mode is not DRM_MODE_BLEND_PREMULTI.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240717-alpha-blending-v4-4-4b1c806c0749@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Support "Pre-multiplied" alpha blending mode on in OVL.
Before this patch, only the "coverage" mode is supported.
As whether OVL_CON_CLRFMT_MAN bit is enabled, (3 << 12)
means different formats in the datasheet. To prevent
misunderstandings going forward, instead of reusing
OVL_CON_CLRFMT_RGBA8888, we intetionally defined
OVL_CON_CLRFMT_PARGB8888 with bit operation again.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240717-alpha-blending-v4-3-4b1c806c0749@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This driver is intended as a "client" end of the console connection.
When connected to a host it's supposed to receive debug logs, and
possibly allow to interact with whatever debug console is available
there. Feeding messages back, depending on a configuration may cause log
messages be executed as shell commands (which can be really bad if one
is unlucky, imagine a log message like "prevented running `rm -rf
/home`"). In case of Xen, it exposes sysrq-like debug interface, and
feeding it its own logs will pretty quickly hit 'R' for "instant
reboot".
Contrary to a classic serial console, the USB one cannot be configured
ahead of time, as the device shows up only when target OS is up. And at
the time device is opened to execute relevant ioctl, it's already too
late, especially when logs start flowing shortly after device is
initialized.
Avoid the issue by changing default to no echo for this type of devices.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
[ johan: amend summary; disable also ECHONL ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
RPN with 127:127 is treated as a Null RPN, just to reset the
parameters, and it's not translated to MIDI2. Although the current
code can work as is in most cases, better to implement the RPN reset
explicitly for Null message.
Link: https://patch.msgid.link/20240731130528.12600-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like the core UMP conversion helper, we need to deal with the
partially-filled RPN/NRPN data in the sequencer UMP converter as
well.
Link: https://patch.msgid.link/20240731130528.12600-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UMP core conversion helper API already defines the context needed
to record the bank and RPN/NRPN values, and we can simply re-use the
same struct instead of re-defining the same content as a different
name.
Link: https://patch.msgid.link/20240731130528.12600-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RPN with 127:127 is treated as a Null RPN, just to reset the
parameters, and it's not translated to MIDI2. Although the current
code can work as is in most cases, better to implement the RPN reset
explicitly for Null message.
Link: https://patch.msgid.link/20240731130528.12600-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UMP 1.1 spec says that an RPN/NRPN should be sent when one of the
following occurs:
* a CC 38 is received
* a subsequent CC 6 is received
* a CC 98, 99, 100, and 101 is received, indicating the last RPN/NRPN
message has ended and a new one has started
That said, we should send a partial data even if it's not fully
filled. Let's change the UMP conversion helper code to follow that
rule.
Link: https://patch.msgid.link/20240731130528.12600-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In this patch, BTF is used to turn enum value to the corresponding
name. There is only one system call that uses enum value as its
argument, that is `landlock_add_rule()`.
The vmlinux btf is loaded lazily, when user decided to trace the
`landlock_add_rule` syscall. But if one decide to run `perf trace`
without any arguments, the behaviour is to trace `landlock_add_rule`,
so vmlinux btf will be loaded by default.
The laziest behaviour is to load vmlinux btf when a
`landlock_add_rule` syscall hits. But I think you could lose some
samples when loading vmlinux btf at run time, for it can delay the
handling of other samples. I might need your precious opinions on
this...
before:
```
perf $ ./perf trace -e landlock_add_rule
0.000 ( 0.008 ms): ldlck-test/438194 landlock_add_rule(rule_type: 2) = -1 EBADFD (File descriptor in bad state)
0.010 ( 0.001 ms): ldlck-test/438194 landlock_add_rule(rule_type: 1) = -1 EBADFD (File descriptor in bad state)
```
after:
```
perf $ ./perf trace -e landlock_add_rule
0.000 ( 0.029 ms): ldlck-test/438194 landlock_add_rule(rule_type: LANDLOCK_RULE_NET_PORT) = -1 EBADFD (File descriptor in bad state)
0.036 ( 0.004 ms): ldlck-test/438194 landlock_add_rule(rule_type: LANDLOCK_RULE_PATH_BENEATH) = -1 EBADFD (File descriptor in bad state)
```
Committer notes:
Made it build with NO_LIBBPF=1, simplified btf_enum_fprintf(), see [1]
for the discussion.
Signed-off-by: Howard Chu <howardchu95@gmail.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Günther Noack <gnoack@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mickaël Salaün <mic@digikod.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/lkml/20240613022757.3589783-1-howardchu95@gmail.com
Link: https://lore.kernel.org/lkml/ZnXAhFflUl_LV1QY@x1 # [1]
Link: https://lore.kernel.org/r/20240624181345.124764-3-howardchu95@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For bus_register(), any error which happens after kset_register() will
cause that @priv are freed twice, fixed by setting @priv with NULL after
the first free.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240727-bus_register_fix-v1-1-fed8dd0dba7a@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function struct kobject *virtual_device_parent(struct device *dev)
does not use its parameter @dev, and the kobject returned also has
nothing deal with specific device, so remove the unused parameter.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240725-virtual_kobj_fix-v1-1-36335cae4544@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -EIO instead of 0 for below erroneous bus attribute operations:
- read a bus attribute without show().
- write a bus attribute without store().
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240724-bus_fix-v2-1-5adbafc698fb@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For class-device, device_rename() failure maybe cause unexpected link name
within its class folder as explained below:
/sys/class/.../old_name -> /sys/devices/.../old_name
device_rename(..., new_name) and failed
/sys/class/.../new_name -> /sys/devices/.../old_name
Fixed by undoing renaming link if renaming kobject failed.
Fixes: f349cf3473 ("driver core: Implement ns directory support for device classes.")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240722-device_rename_fix-v2-1-77de1a6c6495@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devlink_(add|remove)_symlinks() kzalloc() memory to save symlink name
for both supplier and consumer, but do not explicitly take into account
consumer's prefix "consumer:", so cause disadvantages listed below:
1) it seems wrong for the algorithm to calculate memory size
2) readers maybe need to count characters one by one of both prefix
strings to confirm calculated memory size
3) it is relatively easy to introduce new bug if either prefix string
is modified in future
solved by taking into account consumer's prefix as well.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20240712-devlink_fix-v3-1-fa1c5172ffc7@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
