Hibernation can be enabled on SPI-connected devices now that
the hibernate and wake sequences have been updated to work
with wake-on-MOSI.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231006111039.101914-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This can now be re-enabled as the sequence to reliably wake the device
has been implemented in the shared code.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231006111039.101914-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the dummy wake is a toggling signal (either I2C or SPI activity) it
is not guaranteed to meet the minimum asserted hold time for a wake
signal. In this case the wake must guarantee rising edges separated by
at least the minimum hold time.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231006111039.101914-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the hardware uses SPI_MOSI, I2C_SCL or I2C_SDA as the wake source
the bus activity of sending HIBERNATE_NOW will wake up the amps that
were already put into hibernate.
ALLOW_AUTO_HIBERNATE tells the firmware to hibernate itself after a
timeout of a few seconds, giving the driver instances time to send this
before any amps have gone into hibernate.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231006111039.101914-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The pipeline priority is set in topology and driver should sort pipeline
based on priority for trigger order.
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20231006084454.19170-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver set pipeline priority according to priority setting in topology.
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20231006084454.19170-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
IMX93 A0 chip involve the internal q-channel handshake in LPCG and
CCM to automatically handle the Flex-CAN IPG STOP signal. Only after
FLEX-CAN enter stop mode then can support the self-wakeup feature.
But meet issue when do the continue system PM stress test. When config
the CAN as wakeup source, the first time after system suspend, any data
on CAN bus can wakeup the system, this is as expect. But the second time
when system suspend, data on CAN bus can't wakeup the system. If continue
this test, we find in odd time system enter suspend, CAN can wakeup the
system, but in even number system enter suspend, CAN can't wakeup the
system. IC find a bug in the auto stop mode logic, and can't fix it easily.
So for the new imx93 A1, IC drop the auto stop mode and involve the
GPR to support stop mode (used before). IC define a bit in GPR which can
trigger the IPG STOP signal to Flex-CAN, let it go into stop mode.
And NXP claim to drop IMX93 A0, and only support IMX93 A1. So this patch
remove the auto stop mode, and add flag FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR
to imx93.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/all/20230726112458.3524165-2-haibo.chen@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upstream commit 717c6ec241 ("can: sja1000: Prevent overrun stalls with
a soft reset on Renesas SoCs") fixes an issue with Renesas own SJA1000
CAN controller reception: the Rx buffer is only 5 messages long, so when
the bus loaded (eg. a message every 50us), overrun may easily
happen. Upon an overrun situation, due to a possible internal crosstalk
situation, the controller enters a frozen state which only can be
unlocked with a soft reset (experimentally). The solution was to offload
a call to sja1000_start() in a threaded handler. This needs to happen in
process context as this operation requires to sleep. sja1000_start()
basically enters "reset mode", performs a proper software reset and
returns back into "normal mode".
Since this fix was introduced, we no longer observe any stalls in
reception. However it was sporadically observed that the transmit path
would now freeze. Further investigation blamed the fix mentioned above,
and especially the reset operation. Reproducing the reset in a loop
helped identifying what could possibly go wrong. The sja1000 is a single
Tx queue device, which leverages the netdev helpers to process one Tx
message at a time. The logic is: the queue is stopped, the message sent
to the transceiver, once properly transmitted the controller sets a
status bit which triggers an interrupt, in the interrupt handler the
transmission status is checked and the queue woken up. Unfortunately, if
an overrun happens, we might perform the soft reset precisely between
the transmission of the buffer to the transceiver and the advent of the
transmission status bit. We would then stop the transmission operation
without re-enabling the queue, leading to all further transmissions to
be ignored.
The reset interrupt can only happen while the device is "open", and
after a reset we anyway want to resume normal operations, no matter if a
packet to transmit got dropped in the process, so we shall wake up the
queue. Restarting the device and waking-up the queue is exactly what
sja1000_set_mode(CAN_MODE_START) does. In order to be consistent about
the queue state, we must acquire a lock both in the reset handler and in
the transmit path to ensure serialization of both operations. It turns
out, a lock is already held when entering the transmit path, so we can
just acquire/release it as well with the regular net helpers inside the
threaded interrupt handler and this way we should be safe. As the
reset handler might still be called after the transmission of a frame to
the transceiver but before it actually gets transmitted, we must ensure
we don't leak the skb, so we free it (the behavior is consistent, no
matter if there was an skb on the stack or not).
Fixes: 717c6ec241 ("can: sja1000: Prevent overrun stalls with a soft reset on Renesas SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20231002160206.190953-1-miquel.raynal@bootlin.com
[mkl: fixed call to can_free_echo_skb()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
imx93 A0 chip use the internal q-channel handshake signal in LPCG
and CCM to automatically handle the Flex-CAN stop mode. But this
method meet issue when do the system PM stress test. IC can't fix
it easily. So in the new imx93 A1 chip, IC drop this method, and
involve back the old way，use the GPR method to trigger the Flex-CAN
stop mode signal. Now NXP claim to drop imx93 A0, and only support
imx93 A1. So here add the stop mode through GPR.
This patch also fix a typo for aonmix_ns_gpr.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/all/20230726112458.3524165-1-haibo.chen@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With patch [1], isotp_poll was updated to also queue the poller in the
so->wait queue, which is used for send state changes. Since the queue
now also contains polling tasks that are not interested in sending, the
queue fill state can no longer be used as an indication of send
readiness. As a consequence, nonblocking writes can lead to a race and
lock-up of the socket if there is a second task polling the socket in
parallel.
With this patch, isotp_sendmsg does not consult wq_has_sleepers but
instead tries to atomically set so->tx.state and waits on so->wait if it
is unable to do so. This behavior is in alignment with isotp_poll, which
also checks so->tx.state to determine send readiness.
V2:
- Revert direct exit to goto err_event_drop
[1] https://lore.kernel.org/all/20230331125511.372783-1-michal.sojka@cvut.cz
Reported-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Closes: https://lore.kernel.org/linux-can/11328958-453f-447f-9af8-3b5824dfb041@munic.io/
Signed-off-by: Lukas Magel <lukas.magel@posteo.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Fixes: 79e19fa79c ("can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events")
Link: https://github.com/pylessard/python-udsoncan/issues/178#issuecomment-1743786590
Link: https://lore.kernel.org/all/20230827092205.7908-1-lukas.magel@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
commit d61491a51f ("net/sched: cls_u32: Replace one-element array
with flexible-array member") incorrecly replaced an instance of
`sizeof(*tp_c)` with `struct_size(tp_c, hlist->ht, 1)`. This results
in a an over-allocation of 8 bytes.
This change is wrong because `hlist` in `struct tc_u_common` is a
pointer:
net/sched/cls_u32.c:
struct tc_u_common {
struct tc_u_hnode __rcu *hlist;
void *ptr;
int refcnt;
struct idr handle_idr;
struct hlist_node hnode;
long knodes;
};
So, the use of `struct_size()` makes no sense: we don't need to allocate
any extra space for a flexible-array member. `sizeof(*tp_c)` is just fine.
So, `struct_size(tp_c, hlist->ht, 1)` translates to:
sizeof(*tp_c) + sizeof(tp_c->hlist->ht) ==
sizeof(struct tc_u_common) + sizeof(struct tc_u_knode *) ==
144 + 8 == 0x98 (byes)
^^^
|
unnecessary extra
allocation size
$ pahole -C tc_u_common net/sched/cls_u32.o
struct tc_u_common {
struct tc_u_hnode * hlist; /* 0 8 */
void * ptr; /* 8 8 */
int refcnt; /* 16 4 */
/* XXX 4 bytes hole, try to pack */
struct idr handle_idr; /* 24 96 */
/* --- cacheline 1 boundary (64 bytes) was 56 bytes ago --- */
struct hlist_node hnode; /* 120 16 */
/* --- cacheline 2 boundary (128 bytes) was 8 bytes ago --- */
long int knodes; /* 136 8 */
/* size: 144, cachelines: 3, members: 6 */
/* sum members: 140, holes: 1, sum holes: 4 */
/* last cacheline: 16 bytes */
};
And with `sizeof(*tp_c)`, we have:
sizeof(*tp_c) == sizeof(struct tc_u_common) == 144 == 0x90 (bytes)
which is the correct and original allocation size.
Fix this issue by replacing `struct_size(tp_c, hlist->ht, 1)` with
`sizeof(*tp_c)`, and avoid allocating 8 too many bytes.
The following difference in binary output is expected and reflects the
desired change:
| net/sched/cls_u32.o
| @@ -6148,7 +6148,7 @@
| include/linux/slab.h:599
| 2cf5: mov 0x0(%rip),%rdi # 2cfc <u32_init+0xfc>
| 2cf8: R_X86_64_PC32 kmalloc_caches+0xc
|- 2cfc: mov $0x98,%edx
|+ 2cfc: mov $0x90,%edx
Reported-by: Alejandro Colomar <alx@kernel.org>
Closes: https://lore.kernel.org/lkml/09b4a2ce-da74-3a19-6961-67883f634d98@kernel.org/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún says:
====================
net: dsa: qca8k: fix qca8k driver for Turris 1.x
this is v2 of
https://lore.kernel.org/netdev/20231002104612.21898-1-kabel@kernel.org/
Changes since v1:
- fixed a typo in commit message noticed by Simon Horman
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus
also Micron ethernet PHY (dedicated to the WAN port).
We've been experiencing a strange behavior of the WAN ethernet
interface, wherein the WAN PHY started timing out the MDIO accesses, for
example when the interface was brought down and then back up.
Bisecting led to commit 2cd5485663 ("net: dsa: qca8k: add support for
phy read/write with mgmt Ethernet"), which added support to access the
QCA8337 switch's internal PHYs via management ethernet frames.
Connecting the MDIO bus pins onto an oscilloscope, I was able to see
that the MDIO bus was active whenever a request to read/write an
internal PHY register was done via an management ethernet frame.
My theory is that when the switch core always communicates with the
internal PHYs via the MDIO bus, even when externally we request the
access via ethernet. This MDIO bus is the same one via which the switch
and internal PHYs are accessible to the board, and the board may have
other devices connected on this bus. An ASCII illustration may give more
insight:
+---------+
+----| |
| | WAN PHY |
| +--| |
| | +---------+
| |
| | +----------------------------------+
| | | QCA8337 |
MDC | | | +-------+ |
------o-+--|--------o------------o--| | |
MDIO | | | | | PHY 1 |-|--to RJ45
--------o--|---o----+---------o--+--| | |
| | | | | +-------+ |
| +-------------+ | o--| | |
| | MDIO MDC | | | | PHY 2 |-|--to RJ45
eth1 | | | o--+--| | |
-----------|-|port0 | | | +-------+ |
| | | | o--| | |
| | switch core | | | | PHY 3 |-|--to RJ45
| +-------------+ o--+--| | |
| | | +-------+ |
| | o--| ... | |
+----------------------------------+
When we send a request to read an internal PHY register via an ethernet
management frame via eth1, the switch core receives the ethernet frame
on port 0 and then communicates with the internal PHY via MDIO. At this
time, other potential devices, such as the WAN PHY on Turris 1.x, cannot
use the MDIO bus, since it may cause a bus conflict.
Fix this issue by locking the MDIO bus even when we are accessing the
PHY registers via ethernet management frames.
Fixes: 2cd5485663 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c766e077d9 ("net: dsa: qca8k: convert to regmap read/write
API") introduced bulk read/write methods to qca8k's regmap.
The regmap bulk read/write methods get the register address in a buffer
passed as a void pointer parameter (the same buffer contains also the
read/written values). The register address occupies only as many bytes
as it requires at the beginning of this buffer. For example if the
.reg_bits member in regmap_config is 16 (as is the case for this
driver), the register address occupies only the first 2 bytes in this
buffer, so it can be cast to u16.
But the original commit implementing these bulk read/write methods cast
the buffer to u32:
u32 reg = *(u32 *)reg_buf & U16_MAX;
taking the first 4 bytes. This works on little endian systems where the
first 2 bytes of the buffer correspond to the low 16-bits, but it
obviously cannot work on big endian systems.
Fix this by casting the beginning of the buffer to u16 as
u32 reg = *(u16 *)reg_buf;
Fixes: c766e077d9 ("net: dsa: qca8k: convert to regmap read/write API")
Signed-off-by: Marek Behún <kabel@kernel.org>
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the led_hw_* hooks to support hardware blinking LEDs on
the DP83867 phy. The driver supports all LED modes that have a
corresponding TRIGGER_NETDEV_* define. Error and collision do not have
a TRIGGER_NETDEV_* define, so these modes are currently not supported.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS (for
array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct flow_action_entry.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Link: https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci [1]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use macros defined in linux/cleanup.h to automate resource lifetime
control in the driver.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS (for
array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct packet_fanout.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Anqi Shen <amy.saq@antgroup.com>
Cc: netdev@vger.kernel.org
Link: https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci [1]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases we already read the value from the register followed
by a reading of it again for other purposes, but the both reads
are under the lock and bits we are insterested in are not going
to change (they are not volatile from HW perspective). Hence, no
need to read the same register twice.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Chuck points out that we should use the uapi-header property
when generating the guard. Otherwise we may generate the same
guard as another file in the tree.
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to devm_get_gpiod() for discrete GPIOs for clks / regulators / LEDs
and let devm do the cleanup for us.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20231004162317.163488-5-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Use the new skl_int3472_gpiod_get_from_temp_lookup() helper to get
a gpio to pass to register_gpio_clock(), skl_int3472_register_regulator()
and skl_int3472_register_pled().
This removes all use of the deprecated gpiod_toggle_active_low() and
acpi_get_and_request_gpiod() functions.
Suggested-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20231004162317.163488-4-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add a new skl_int3472_gpiod_get_from_temp_lookup() helper.
This is a preparation patch for removing usage of the deprecated
gpiod_toggle_active_low() and acpi_get_and_request_gpiod() functions.
[hdegoede@redhat.com] use the new skl_int3472_fill_gpiod_lookup() helper
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231004162317.163488-3-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add a new skl_int3472_fill_gpiod_lookup() helper.
This is a preparation patch for removing usage of the deprecated
gpiod_toggle_active_low() and acpi_get_and_request_gpiod() functions.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20231004162317.163488-2-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Array BIST MSR addresses, bit definition and semantics are different for
Sierra Forest. Branch into a separate Array BIST flow on Sierra Forest
when user invokes Array Test.
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20231005195137.3117166-10-jithu.joseph@intel.com
[ij: ARRAY_GEN_* -> ARRAY_GEN* for consistency]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Petr Machata says:
====================
mlxsw: Control the order of blocks in ACL region
Amit Cohen writes:
For 12 key blocks in the A-TCAM, rules are split into two records, which
constitute two lookups. The two records are linked using a
"large entry key ID".
Due to a Spectrum-4 hardware issue, KVD entries that correspond to key
blocks 0 to 5 of 12 key blocks will be placed in the same KVD pipe if they
only differ in their "large entry key ID", as it is ignored. This results
in a reduced scale, we can insert less than 20k filters and get an error:
$ tc -b flower.batch
RTNETLINK answers: Input/output error
We have an error talking to the kernel
To reduce the probability of this issue, we can place key blocks with
high entropy in blocks 0 to 5. The idea is to place blocks that are often
changed in blocks 0 to 5, for example, key blocks that match on IPv4
addresses or the LSBs of IPv6 addresses. Such placement will reduce the
probability of these blocks to be same.
Mark several blocks with 'high_entropy' flag and place them in blocks 0
to 5. Note that the list of the blocks is just a suggestion, I will verify
it with architects.
Currently, there is a one loop that chooses which blocks should be used
for a given list of elements and fills the blocks - when a block is
chosen, it fills it in the region. To be able to control the order of
the blocks, separate between searching blocks and filling them. Several
pre-changes are required.
Patch set overview:
Patch #1 marks several blocks with 'high_entropy' flag.
Patches #2-#4 prepare the code for filling blocks at the end of the search.
Patch #5 changes the loop to just choose the blocks and fill the blocks at
the end.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches prepared the code to allow separating between
choosing blocks and filling blocks.
Do not add blocks as part of the loop that chooses them. When all the
required blocks are set in the bitmap 'chosen_blocks_bm', start filling
blocks. Iterate over the bitmap twice - first add only blocks that are
marked with 'high_entropy' flag. Then, fill the rest of the blocks.
The idea is to place key blocks with high entropy in blocks 0 to 5. See
more details in previous patches.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlxsw_afk_picker() chooses which blocks will be used for a
given list of elements, and fills the blocks during the searching - when a
key block is found with most hits, it adds it and removes the elements from
the count of hits. This should be changed as we want to be able to choose
which blocks will be placed in blocks 0 to 5.
To separate between choosing blocks and filling blocks, several pre-changes
are required. Currently, the indication of whether all elements were
found in the chosen blocks is by the structure 'key_info->elusage'. This
structure is updated when block is filled as part of
mlxsw_afk_picker_key_info_add(). A following patch will call this
function only after choosing all the blocks. Add a bitmap called
'elusage_chosen' to store which elements were chosen in the chosen blocks.
Change the condition in the loop to check elements that were chosen, not
elements that were already filled in the blocks.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlxsw_afk_picker() chooses which blocks will be used for a
given list of elements, and fills the blocks during the searching - when a
key block is found with most hits, it adds it and removes the elements from
the count of hits. This should be changed as we want to be able to choose
which blocks will be placed in blocks 0 to 5.
To separate between choosing blocks and filling blocks, several pre-changes
are required. During the search, the structure 'mlxsw_afk_picker' is
used per block, it contains how many elements from the required list appear
in the block. When a block is chosen and filled, this bitmap of elements is
cleaned. To be able to fill the blocks at the end, add a bitmap called
'chosen_element' as part of picker. When a block is chosen, copy the
'element' bitmap to it. Use the new bitmap as part of
mlxsw_afk_picker_key_info_add(). So later, when filling the block will
be done at the end of the searching, we will use the copied bitmap that
contains the elements that should be used in the block.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlxsw_afk_picker() chooses which blocks will be used for a
given list of elements, and fills the blocks during the searching - when a
key block is found with most hits, it adds it and removes the elements from
the count of hits. This should be changed as we want to be able to choose
which blocks will be placed in blocks 0 to 5.
To separate between choosing blocks and filling blocks, several pre-changes
are required. The indexes of the chosen blocks should be saved, so then
the relevant blocks will be filled at the end of search.
Allocate a bitmap for chosen blocks, when a block is found with most
hits, set the relevant bit in the bitmap. This bitmap will be used in a
following patch.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 12 key blocks in the A-TCAM, rules are split into two records, which
constitute two lookups. The two records are linked using a
"large entry key ID".
Due to a Spectrum-4 hardware issue, KVD entries that correspond to key
blocks 0 to 5 of 12 key blocks A-TCAM entries will be placed in the same
KVD pipe if they only differ in their "large entry key ID", as it is
ignored. This results in a reduced scale. To reduce the probability of this
issue, we can place key blocks with high entropy in blocks 0 to 5. The idea
is to place blocks that are changed often in blocks 0 to 5, for
example, key blocks that match on IPv4 addresses or the LSBs of IPv6
addresses. Such placement will reduce the probability of these blocks to be
same.
Mark several blocks with 'high_entropy' flag, so later we will take into
account this flag and place them in blocks 0 to 5.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
sfc: conntrack offload for tunnels
This series adds support for offloading TC flower rules which require
both connection tracking and tunnel decapsulation. Depending on the
match keys required, the left-hand-side rule may go in either the
Outer Rule table or the Action Rule table.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a foreign LHS rule (TC rule from a tunnel netdev which requests
conntrack lookup) matches on inner headers or enc_key_id, these matches
cannot be performed by the Outer Rule table, as the keys are only
available after the tunnel type has been identified (by the OR lookup)
and the rest of the headers parsed accordingly.
Offload such rules with an Action Rule, using the LOOKUP_CONTROL section
of the AR response to specify the conntrack and/or recirculation actions,
combined with an Outer Rule which performs only the usual Encap Match
duties.
This processing flow, as it requires two AR lookups per packet, is less
performant than OR-CT-AR, so only use it where necessary.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a few places where no extack error message was set, or the
extack was not forwarded to callees, potentially resulting in a return
of -EOPNOTSUPP with no additional information.
Make sure to populate the error message in these cases. In practice
this does us no good as TC indirect block callbacks don't come with an
extack to fill in; but maybe they will someday and when debugging it's
possible to provide a fake extack and emit its message to the console.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally, if a TC filter on a tunnel netdev does not match on any
encap fields, we decline to offload it, as it cannot meet our
requirement for a <sip,dip,dport> tuple for the encap match.
However, if the rule has a nonzero chain_index, then for a packet to
reach the rule, it must already have matched a LHS rule which will
have included an encap match and determined the tunnel type, so in
that case we can offload the right-hand-side rule.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a tunnel netdevice (such as a vxlan) to offload conntrack lookups,
in much the same way as efx netdevs.
To ensure this rule does not overlap with other tunnel rules on the same
sip,dip,dport tuple, register a pseudo encap match of a new type
(EFX_TC_EM_PSEUDO_OR), which unlike PSEUDO_MASK may only be referenced
once (because an actual Outer Rule in hardware exists, although its
fw_id is not recorded in the encap match entry).
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make driver aware of a newly added error code so that it can provide a
more appropriate error message.
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20231005195137.3117166-9-jithu.joseph@intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add Granite Rapids(GNR) and Sierra Forest(SRF) cpuids to x86 match table
so that IFS driver can be loaded for those.
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20231005195137.3117166-8-jithu.joseph@intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add an additional check to validate IFS image metadata field prior to
loading the test image.
If start_chunk is not a multiple of chunks_per_stride error out.
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20231005195137.3117166-7-jithu.joseph@intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Perform additional validation prior to loading IFS image.
Error out if the size of the file being loaded doesn't match the size
specified in the header.
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20231005195137.3117166-6-jithu.joseph@intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Width of chunk related bitfields is ACTIVATE_SCAN and SCAN_STATUS MSRs
are different in newer IFS generation compared to gen0.
Make changes to scan test flow such that MSRs are populated
appropriately based on the generation supported by hardware.
Account for the 8/16 bit MSR bitfield width differences between gen0 and
newer generations for the scan test trace event too.
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20231005195137.3117166-5-jithu.joseph@intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Scan image loading flow for newer IFS generations are slightly different
from that of current generation. In newer schemes, loading need not be
done once for each socket as was done in gen0.
Also the width of NUM_CHUNKS bitfield in SCAN_HASHES_STATUS MSR has
increased from 8 -> 16 bits. Similarly there are width differences for
CHUNK_AUTHENTICATION_STATUS too.
Further the parameter to AUTHENTICATE_AND_COPY_CHUNK is passed
differently in newer generations.
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20231005195137.3117166-4-jithu.joseph@intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
IFS image loading flow is slightly different for newer IFS generations.
In preparation for adding support for newer IFS generations, refactor
portions of existing image loading code for reuse.
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20231005195137.3117166-3-jithu.joseph@intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
IFS generation number is reported via MSR_INTEGRITY_CAPS. As IFS
support gets added to newer CPUs, some differences are expected during
IFS image loading and test flows.
Define MSR bitmasks to extract and store the generation in driver data,
so that driver can modify its MSR interaction appropriately.
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20231005195137.3117166-2-jithu.joseph@intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Vladimir Oltean says:
====================
Fixes for lynx-28g PHY driver
This series fixes some issues in the Lynx 28G SerDes driver, namely an
oops when unloading the module, a race between the periodic workqueue
and the PHY API, and a race between phy_set_mode_ext() calls on multiple
lanes on the same SerDes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The protocol converter configuration registers PCC8, PCCC, PCCD
(implemented by the driver), as well as others, control protocol
converters from multiple lanes (each represented as a different
struct phy). So, if there are simultaneous calls to phy_set_mode_ext()
to lanes sharing the same PCC register (either for the "old" or for the
"new" protocol), corruption of the values programmed to hardware is
possible, because lynx_28g_rmw() has no locking.
Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take
the global spinlock from the phy_ops :: set_mode() implementation. There
are no other callers which modify PCC registers.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
