Add a note that fec_enable actually means FEC is to be enabled
explicitly. 128b/132b always has FEC enabled, the driver doesn't need to
enable it separately, and fec_enable will be false.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920112901.3315876-1-jani.nikula@intel.com
In ath9k_hif_usb_resume, the error handling code calls
ath9k_hif_usb_dealloc_urbs twice in different paths.
To unify the error handling code, we move the else branch before
the if branch and drop one level of indentation of the if branch.
In addition, move the ret variable at the end of variable declarations
to be reverse x-mas tree order.
Note that this patch does not incur any functionability change.
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230905013556.2595854-1-dzm91@hust.edu.cn
In ath12k_dp_tx(), if we reach fail_dma_unmap due to some errors,
current code does DMA unmap unconditionally on skb_cb->paddr_ext_desc.
However, skb_cb->paddr_ext_desc may be NULL and thus we get below
warning:
kernel: [ 8887.076212] WARNING: CPU: 3 PID: 0 at drivers/iommu/dma-iommu.c:1077 iommu_dma_unmap_page+0x79/0x90
Fix it by checking skb_cb->paddr_ext_desc before unmap it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230830021131.5610-1-quic_bqiang@quicinc.com
reg_cap.phy_id is extracted from WMI event and could be an unexpected value
in case some errors happen. As a result out-of-bound write may occur to
soc->hal_reg_cap. Fix it by validating reg_cap.phy_id before using it.
This is found during code review.
Compile tested only.
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230830020716.5420-1-quic_bqiang@quicinc.com
Except on x86, preempt_count is always accessed with READ_ONCE().
Repeated invocations in macros like irq_count() produce repeated loads.
These redundant instructions appear in various fast paths. In the one
shown below, for example, irq_count() is evaluated during kernel entry
if !tick_nohz_full_cpu(smp_processor_id()).
0001ed0a <irq_enter_rcu>:
1ed0a: 4e56 0000 linkw %fp,#0
1ed0e: 200f movel %sp,%d0
1ed10: 0280 ffff e000 andil #-8192,%d0
1ed16: 2040 moveal %d0,%a0
1ed18: 2028 0008 movel %a0@(8),%d0
1ed1c: 0680 0001 0000 addil #65536,%d0
1ed22: 2140 0008 movel %d0,%a0@(8)
1ed26: 082a 0001 000f btst #1,%a2@(15)
1ed2c: 670c beqs 1ed3a <irq_enter_rcu+0x30>
1ed2e: 2028 0008 movel %a0@(8),%d0
1ed32: 2028 0008 movel %a0@(8),%d0
1ed36: 2028 0008 movel %a0@(8),%d0
1ed3a: 4e5e unlk %fp
1ed3c: 4e75 rts
This patch doesn't prevent the pointless btst and beqs instructions
above, but it does eliminate 2 of the 3 pointless move instructions
here and elsewhere.
On x86, preempt_count is per-cpu data and the problem does not arise
presumably because the compiler is free to optimize more effectively.
This patch was tested on m68k and x86. I was expecting no changes
to object code for x86 and mostly that's what I saw. However, there
were a few places where code generation was perturbed for some reason.
The performance issue addressed here is minor on uniprocessor m68k. I
got a 0.01% improvement from this patch for a simple "find /sys -false"
benchmark. For architectures and workloads susceptible to cache line bounce
the improvement is expected to be larger. The only SMP architecture I have
is x86, and as x86 unaffected I have not done any further measurements.
Fixes: 15115830c8 ("preempt: Cleanup the macro maze a bit")
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/0a403120a682a525e6db2d81d1a3ffcc137c3742.1694756831.git.fthain@linux-m68k.org
The fallback alternative uses %rsi register to manually load pointer
to the percpu variable before the call to the emulation function.
This is unoptimal, because the load is hidden from the compiler.
Move the load of %rsi outside inline asm, so the compiler can
reuse the value. The code in slub.o improves from:
55ac: 49 8b 3c 24 mov (%r12),%rdi
55b0: 48 8d 4a 40 lea 0x40(%rdx),%rcx
55b4: 49 8b 1c 07 mov (%r15,%rax,1),%rbx
55b8: 4c 89 f8 mov %r15,%rax
55bb: 48 8d 37 lea (%rdi),%rsi
55be: e8 00 00 00 00 callq 55c3 <...>
55bf: R_X86_64_PLT32 this_cpu_cmpxchg16b_emu-0x4
55c3: 75 a3 jne 5568 <...>
55c5: ...
0000000000000000 <.altinstr_replacement>:
5: 65 48 0f c7 0f cmpxchg16b %gs:(%rdi)
to:
55ac: 49 8b 34 24 mov (%r12),%rsi
55b0: 48 8d 4a 40 lea 0x40(%rdx),%rcx
55b4: 49 8b 1c 07 mov (%r15,%rax,1),%rbx
55b8: 4c 89 f8 mov %r15,%rax
55bb: e8 00 00 00 00 callq 55c0 <...>
55bc: R_X86_64_PLT32 this_cpu_cmpxchg16b_emu-0x4
55c0: 75 a6 jne 5568 <...>
55c2: ...
Where the alternative replacement instruction now uses %rsi:
0000000000000000 <.altinstr_replacement>:
5: 65 48 0f c7 0e cmpxchg16b %gs:(%rsi)
The instruction (effectively a reg-reg move) at 55bb: in the original
assembly is removed. Also, both the CALL and replacement CMPXCHG16B
are 5 bytes long, removing the need for NOPs in the asm code.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230918151452.62344-1-ubizjak@gmail.com
Sebastian Andrzej Siewior says:
====================
Add missing xdp_do_flush() invocations.
I've been looking at the drivers/ XDP users and noticed that some
XDP_REDIRECT user don't invoke xdp_do_flush() at the end.
====================
Link: https://lore.kernel.org/r/20230918153611.165722-1-bigeasy@linutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
xdp_do_flush() should be invoked before leaving the NAPI poll function
if XDP-redirect has been performed.
Invoke xdp_do_flush() before leaving NAPI.
Cc: Geetha sowjanya <gakula@marvell.com>
Cc: Subbaraya Sundeep <sbhatta@marvell.com>
Cc: Sunil Goutham <sgoutham@marvell.com>
Cc: hariprasad <hkelam@marvell.com>
Fixes: 06059a1a9a ("octeontx2-pf: Add XDP support to netdev PF")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Geethasowjanya Akula <gakula@marvell.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bnxt_poll_nitroa0() invokes bnxt_rx_pkt() which can run a XDP program
which in turn can return XDP_REDIRECT. bnxt_rx_pkt() is also used by
__bnxt_poll_work() which flushes (xdp_do_flush()) the packets after each
round. bnxt_poll_nitroa0() lacks this feature.
xdp_do_flush() should be invoked before leaving the NAPI callback.
Invoke xdp_do_flush() after a redirect in bnxt_poll_nitroa0() NAPI.
Cc: Michael Chan <michael.chan@broadcom.com>
Fixes: f18c2b77b2 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
xdp_do_flush() should be invoked before leaving the NAPI poll function
after a XDP-redirect. This is not the case if the driver leaves via
the error path (after having a redirect in one of its previous
iterations).
Invoke xdp_do_flush() also in the error path.
Cc: Arthur Kiyanovski <akiyano@amazon.com>
Cc: David Arinzon <darinzon@amazon.com>
Cc: Noam Dagan <ndagan@amazon.com>
Cc: Saeed Bishara <saeedb@amazon.com>
Cc: Shay Agroskin <shayagr@amazon.com>
Fixes: a318c70ad1 ("net: ena: introduce XDP redirect implementation")
Acked-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The 'mid' pointer is being initialized with a value that is never read,
it is being re-assigned and used inside a for-loop. Remove the
redundant initialization.
Cleans up clang scan build warning:
arch/x86/kernel/unwind_orc.c:88:7: warning: Value stored to 'mid' during its initialization is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20230920114141.118919-1-colin.i.king@gmail.com
It was brought up by Tetsuo that the following sequence:
write_seqlock_irqsave()
printk_deferred_enter()
could lead to a deadlock if the lockdep annotation within
write_seqlock_irqsave() triggers.
The problem is that the sequence counter is incremented before the lockdep
annotation is performed. The lockdep splat would then attempt to invoke
printk() but the reader side, of the same seqcount, could have a
tty_port::lock acquired waiting for the sequence number to become even again.
The other lockdep annotations come before the actual locking because "we
want to see the locking error before it happens". There is no reason why
seqcount should be different here.
Do the lockdep annotation first then perform the locking operation (the
sequence increment).
Fixes: 1ca7d67cf5 ("seqcount: Add lockdep functionality to seqcount/seqlock structures")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230920104627._DTHgPyA@linutronix.de
Closes: https://lore.kernel.org/20230621130641.-5iueY1I@linutronix.de
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct libipw_txb.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230915200602.never.582-kees@kernel.org
Since commit:
8a99b6833c ("sched: Move SCHED_DEBUG sysctl to debugfs")
The sched_debug interface moved from /proc to debugfs. The comment
mentions still the outdated proc interfaces.
Update the comment, point to the current location of the interface.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230920130025.412071-3-bigeasy@linutronix.de
Add an algorithm to backoff the Tx Task when low memory scenario is
triggered at firmware. During high data transfer from host, the firmware
runs out of VMM memory, which is used to hold the frames from the host.
So, adding the flow control delays the transmit from host side when
there is not enough space to accommodate frames in firmware side.
Signed-off-by: Prasurjya Rohan Saikia <prasurjya.rohansaikia@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230915175946.4361-1-prasurjya.rohansaikia@microchip.com
The mwifiex_pcie driver is missing the MODULE_FIRMWARE macro to
add the firmware files needed to the module metadata.
Signed-off-by: Víctor Gonzalo <victor.gonzalo@anddroptable.net>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230914211938.28395-1-victor.gonzalo@anddroptable.net
Drop filled with NULL pointers but otherwise unused 'skb_arr'
array of 'struct mwifiex_sdio_mpa_rx', adjust related code.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230821115254.167552-1-dmantipov@yandex.ru
The message said it was an invalid mode, when it was intentionally
not set. Fix confusing message logged to dmesg.
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
These debug printks are missing newlines, causing drm debug logs to be
hard to read. Add newlines so that the messages are on their own line.
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Cc: Vinod Polimera <quic_vpolimer@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 601f0479c5 ("drm/msm/dp: add logs across DP driver for ease of debugging")
Fixes: cd779808cc ("drm/msm/dp: Add basic PSR support for eDP")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/554533/
Link: https://lore.kernel.org/r/20230825230109.2264345-1-swboyd@chromium.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
_dpu_plane_calc_bw() uses integer variables to calculate the bandwidth
used during plane bandwidth calculations. However for high resolution
displays this overflows easily and leads to below errors
[dpu error]crtc83 failed performance check -7
Promote the intermediate variables to u64 to avoid overflow.
changes in v2:
- change to u64 where actually needed in the math
Fixes: c33b7c0389 ("drm/msm/dpu: add support for clk and bw scaling for display")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Nia Espera <nespera@igalia.com>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/32
Tested-by: Nia Espera <nespera@igalia.com>
Patchwork: https://patchwork.freedesktop.org/patch/556288/
Link: https://lore.kernel.org/r/20230908012616.20654-1-quic_abhinavk@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
The irq_of_parse_and_map() function returns zero on error. It
never returns negative error codes. Fix the check.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/557715/
Link: https://lore.kernel.org/r/4f3c5c98-04f7-43f7-900f-5d7482c83eef@moroto.mountain
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
dsi_wait4video_done() API waits for the DSI video mode engine to
become idle so that we can transmit the DCS commands in the
beginning of BLLP. However, with the current sequence, the MDP
timing engine is turned on after the panel's pre_enable() callback
which can send out the DCS commands needed to power up the panel.
During those cases, this API will always timeout and print out the
error spam leading to long bootup times and log flooding.
Fix this by checking if the DSI video engine was actually busy before
waiting for it to become idle otherwise this is a redundant wait.
changes in v2:
- move the reg read below the video mode check
- minor fixes in commit text
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/34
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/557853/
Link: https://lore.kernel.org/r/20230915204426.19011-1-quic_abhinavk@quicinc.com
DP PHY re-initialization done using dp_ctrl_reinitialize_mainlink() will
cause PLL unlocked initially and then PLL gets locked at the end of
initialization. PLL_UNLOCKED interrupt will fire during this time if the
interrupt mask is enabled.
However currently DP driver link training implementation incorrectly
re-initializes PHY unconditionally during link training as the PHY was
already configured in dp_ctrl_enable_mainlink_clocks().
Fix this by re-initializing the PHY only if the previous link training
failed.
[drm:dp_aux_isr] *ERROR* Unexpected DP AUX IRQ 0x01000000 when not busy
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/30
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/551847/
Link: https://lore.kernel.org/r/1691533190-19335-1-git-send-email-quic_khsieh@quicinc.com
[quic_abhinavk@quicinc.com: added line break in commit text]
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Directly use tbo's start address will miss the domain start offset. Need
to use gpu_offset instead.
Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
On eDP we can receive invalid modes from dm_update_crtc_state() for
entirely new streams for which drm_mode_set_crtcinfo() shouldn't be
called on. So, instead of calling drm_mode_set_crtcinfo() from within
create_stream_for_sink() we can instead call it from
amdgpu_dm_connector_mode_valid(). Since, we are guaranteed to only call
drm_mode_set_crtcinfo() for valid modes from that function (invalid
modes are rejected by that callback) and that is the only user
of create_validate_stream_for_sink() that we need to call
drm_mode_set_crtcinfo() for (as before commit cb841d27b8
("drm/amd/display: Always pass connector_state to stream validation"),
that is the only place where create_validate_stream_for_sink()'s
dm_state was NULL).
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2693
Fixes: cb841d27b8 ("drm/amd/display: Always pass connector_state to stream validation")
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fixes a memory leak in the amdgpu_ras_feature_enable() function.
The leak occurs when the function sends a command to the firmware to enable
or disable a RAS feature for a GFX block. If the command fails, the kfree()
function is not called to free the info memory.
Fixes: 9f051d6ff1 ("drm/amdgpu: Free ras cmd input buffer properly")
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Cong Liu <liucong2@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
devm_kstrdup() returns pointer to allocated string on success,
NULL on failure. So it is better to check the return value of it.
Fixes: e35478eac0 ("i2c: mux: demux-pinctrl: run properly with multiple instances")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit 7748ce5b69.
vbios_version sysfs node is used to identify Part Number also. Revert to
the same so that it doesn't break scripts/software which parse this.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
MST now recognizes both connected displays
Fixes: 927e784c18 ("drm/amd/display: Add symclk enable/disable during stream enable/disable")
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix missing set of cifs_open_info_data::reparse_point when SMB2_CREATE
request fails with STATUS_IO_REPARSE_TAG_NOT_HANDLED.
Fixes: 5f71ebc412 ("smb: client: parse reparse point flag in create response")
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The removed line prevents the following cleanup function
to execute a dma_fence_put on the out_fence to free its
memory, producing the following output in kmemleak:
unreferenced object 0xffff888126d8ee00 (size 128):
comm "kwin_wayland", pid 981, jiffies 4295380296 (age 390.060s)
hex dump (first 32 bytes):
c8 a1 c2 27 81 88 ff ff e0 14 a9 c0 ff ff ff ff ...'............
30 1a e1 2e a6 00 00 00 28 fc 5b 17 81 88 ff ff 0.......(.[.....
backtrace:
[<0000000011655661>] kmalloc_trace+0x26/0xa0
[<0000000055f15b82>] virtio_gpu_fence_alloc+0x47/0xc0 [virtio_gpu]
[<00000000fa6d96f9>] virtio_gpu_execbuffer_ioctl+0x1a8/0x800 [virtio_gpu]
[<00000000e6cb5105>] drm_ioctl_kernel+0x169/0x240 [drm]
[<000000005ad33e27>] drm_ioctl+0x399/0x6b0 [drm]
[<00000000a19dbf65>] __x64_sys_ioctl+0xc5/0x100
[<0000000011fa801e>] do_syscall_64+0x5b/0xc0
[<0000000065c76d8a>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
unreferenced object 0xffff888121930500 (size 128):
comm "kwin_wayland", pid 981, jiffies 4295380313 (age 390.096s)
hex dump (first 32 bytes):
c8 a1 c2 27 81 88 ff ff e0 14 a9 c0 ff ff ff ff ...'............
f9 ec d7 2f a6 00 00 00 28 fc 5b 17 81 88 ff ff .../....(.[.....
backtrace:
[<0000000011655661>] kmalloc_trace+0x26/0xa0
[<0000000055f15b82>] virtio_gpu_fence_alloc+0x47/0xc0 [virtio_gpu]
[<00000000fa6d96f9>] virtio_gpu_execbuffer_ioctl+0x1a8/0x800 [virtio_gpu]
[<00000000e6cb5105>] drm_ioctl_kernel+0x169/0x240 [drm]
[<000000005ad33e27>] drm_ioctl+0x399/0x6b0 [drm]
[<00000000a19dbf65>] __x64_sys_ioctl+0xc5/0x100
[<0000000011fa801e>] do_syscall_64+0x5b/0xc0
[<0000000065c76d8a>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[...]
This memleak will grow quickly, being possible to see the
following line in dmesg after few minutes of life in the
virtual machine:
[ 706.217388] kmemleak: 10731 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
The patch will remove the line to allow the cleanup
function do its job.
Signed-off-by: José Pekkarinen <jose.pekkarinen@foxhound.fi>
Fixes: e4812ab8e6 ("drm/virtio: Refactor and optimize job submission code path")
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230912060824.5210-1-jose.pekkarinen@foxhound.fi
In status_to_posix_error STATUS_IO_REPARSE_TAG_NOT_HANDLED was mapped
to both -EOPNOTSUPP and also to -EIO but the later one (-EIO) is
ignored. Remove the duplicate.
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The validated_once flag is not used after the prefault was removed, The
prefault was needed to ensure validate all system memory pages at least
once before mapping or migrating the range to GPU.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Include subrevision and variant fileds also to IP version.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Print channel index for UMC v12.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We do not need free dma address array of svm_range each time we do dma unmap
for pages in svm_range as we can reuse the same array. Only free it when free
svm_range. Separate these two operations and use them accordingly.
Signed-off-by: Xiaogang Chen <xiaogang.chen@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Selectively updating feature mask is not supported in SMU v13.0.6.
Remove the callback corresponding to that.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of neglecting fractional part, round the Q10 format values in
SMU v13.0.6 metrics table.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
update the query to return the number of functional
instances where there is more than an instance of the requested
type and for others continue to return one.
v2: count must reflect the actual number of engines (Alex)
v3: fix wrong number of engines for vcn (Alex)
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It should first check block ras obj whether be set, it should
return 0 directly if block ras obj or hw_ops is not set.
If block doesn't support RAS just return 0 is fine.
Changed from V1:
return 0 directly if block ras obj or hw ops is not set
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Directly use tbo's start address will miss the domain start offset. Need
to use gpu_offset instead.
Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add new IPS ALLOW masks
- Add new Replay power configuration options
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MST now recognizes both connected displays
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix some non-initialized register mask and update golden setting.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable the display replay feature for DCN35.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
