To conclude the ux500 busy timeout fixes, this improves the debug and
error prints so we can see a bit what is going on. Here is a typical
dmesg with these new debug messages enabled:
[ 2.648864] mmci-pl18x 80005000.mmc: mmc2: PL180 manf 80 rev4
at 0x80005000 irq 81,0 (pio)
[ 2.662750] mmci-pl18x 80005000.mmc: DMA channels RX dma0chan4, TX dma0chan5
[ 3.480407] mmci-pl18x 80005000.mmc: no busy signalling in time CMD06
[ 3.487457] mmci-pl18x 80005000.mmc: no busy signalling in time CMD06
[ 3.998321] mmci-pl18x 80005000.mmc: timeout in state waiting for end IRQ
waiting for busy CMD06
[ 3.998535] mmc2: new DDR MMC card at address 0001
[ 4.000030] mmcblk2: mmc2:0001 M4G1YC 3.69 GiB
[ 4.008361] mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15
p16 p17 p18 p19 p20 p21 p22 p23 p24 p25
[ 4.017700] mmcblk2boot0: mmc2:0001 M4G1YC 2.00 MiB
[ 4.020477] mmcblk2boot1: mmc2:0001 M4G1YC 2.00 MiB
[ 4.022125] mmcblk2rpmb: mmc2:0001 M4G1YC 128 KiB, chardev (246:0)
[ 5.791381] mmci-pl18x 80005000.mmc: no busy signalling in time CMD06
[ 10.938568] mmci-pl18x 80005000.mmc: timeout in state waiting for end IRQ
waiting for busy CMD06
[ 17.982849] mmci-pl18x 80005000.mmc: lost busy status when waiting for
busy start IRQ CMD06
[ 18.683563] mmci-pl18x 80005000.mmc: no busy signalling in time CMD06
[ 19.385437] mmci-pl18x 80005000.mmc: no busy signalling in time CMD06
[ 20.493652] mmci-pl18x 80005000.mmc: no busy signalling in time CMD06
We see a lot of lost IRQs and the timeout always occur while waiting for
the end IRQ, and then the busy status is *low* meaning the busy indication
is already de-asserted.
So busy signalling is missed in various ways for various reasons,
sometimes it appears that IRQs are simply lost.
One hypothesis is that this happens because the events happen so fast
that they are transient, and since the MMCI state machine in effect is
handling an edge trigger (rising or falling signal on DAT0) the
internal logic will miss the event, because the state machine in the
hardware is sampling the line, and will at times detect only the first
event but miss the second, fireing only one IRQ.
We print the second timeout error with dev_err() since it is pretty
serious, the other events are so common and simple to handle that we
can keep them at dev_dbg() level.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230628191243.3632401-1-linus.walleij@linaro.org
[Ulf: Fixup conflict in ux500_busy_timeout_work()]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The host pointer is already being dereferenced earlier, so let's just drop
the redundant WARN_ON.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230622105327.77296-1-ulf.hansson@linaro.org
When mmc allocation succeeds, the error paths are not freeing mmc.
Fix the above issue by changing mmc_alloc_host() to devm_mmc_alloc_host()
to simplify the error handling. Remove label 'probe_free_host' as devm_*
api takes care of freeing, also remove mmc_free_host() from remove
function as devm_* takes care of freeing.
Fixes: 4e268fed8b ("mmc: Add mmc driver for Sunplus SP7021")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/a3829ed3-d827-4b9d-827e-9cc24a3ec3bc@moroto.mountain/
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230809071812.547229-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_add_host() may return error, if we ignore its return value,
1. the memory allocated in mmc_alloc_host() will be leaked
2. null-ptr-deref will happen when calling mmc_remove_host()
in remove function spmmc_drv_remove() because deleting not
added device.
Fix this by checking the return value of mmc_add_host(). Moreover,
I fixed the error handling path of spmmc_drv_probe() to clean up.
Fixes: 4e268fed8b ("mmc: Add mmc driver for Sunplus SP7021")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Link: https://lore.kernel.org/r/20230622090233.188539-1-harperchen1110@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Different MT7530 variants require different PHY drivers.
Use 'imply' instead of 'select' to relax the dependency on the PHY
driver, and choose the appropriate driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gerd Bayer says:
====================
net/smc: Fix effective buffer size
commit 0227f058aa ("net/smc: Unbind r/w buffer size from clcsock
and make them tunable") started to derive the effective buffer size for
SMC connections inconsistently in case a TCP fallback was used and
memory consumption of SMC with the default settings was doubled when
a connection negotiated SMC. That was not what we want.
This series consolidates the resulting effective buffer size that is
used with SMC sockets, which is based on Jan Karcher's effort (see
[1]). For all TCP exchanges (in particular in case of a fall back when
no SMC connection was possible) the values from net.ipv4.tcp_[rw]mem
are used. If SMC succeeds in establishing a SMC connection, the newly
introduced values from net.smc.[rw]mem are used.
net.smc.[rw]mem is initialized to 64kB, respectively. Internal test
have show this to be a good compromise between throughput/latency
and memory consumption. Also net.smc.[rw]mem is now decoupled completely
from any tuning through net.ipv4.tcp_[rw]mem.
If a user chose to tune a socket's receive or send buffer size with
setsockopt, this tuning is now consistently applied to either fall-back
TCP or proper SMC connections over the socket.
Thanks,
Gerd
v2 - v3:
- Rebase to and resolve conflict of second patch with latest net/master.
v1 - v2:
- In second patch, use sock_net() helper as suggested by Tony and demanded
by kernel test robot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuning of the effective buffer size through setsockopts was working for
SMC traffic only but not for TCP fall-back connections even before
commit 0227f058aa ("net/smc: Unbind r/w buffer size from clcsock and
make them tunable"). That change made it apparent that TCP fall-back
connections would use net.smc.[rw]mem as buffer size instead of
net.ipv4_tcp_[rw]mem.
Amend the code that copies attributes between the (TCP) clcsock and the
SMC socket and adjust buffer sizes appropriately:
- Copy over sk_userlocks so that both sockets agree on whether tuning
via setsockopt is active.
- When falling back to TCP use sk_sndbuf or sk_rcvbuf as specified with
setsockopt. Otherwise, use the sysctl value for TCP/IPv4.
- Likewise, use either values from setsockopt or from sysctl for SMC
(duplicated) on successful SMC connect.
In smc_tcp_listen_work() drop the explicit copy of buffer sizes as that
is taken care of by the attribute copy.
Fixes: 0227f058aa ("net/smc: Unbind r/w buffer size from clcsock and make them tunable")
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0227f058aa ("net/smc: Unbind r/w buffer size from clcsock
and make them tunable") introduced the net.smc.rmem and net.smc.wmem
sysctls to specify the size of buffers to be used for SMC type
connections. This created a regression for users that specified the
buffer size via setsockopt() as the effective buffer size was now
doubled.
Re-introduce the division by 2 in the SMC buffer create code and level
this out by duplicating the net.smc.[rw]mem values used for initializing
sk_rcvbuf/sk_sndbuf at socket creation time. This gives users of both
methods (setsockopt or sysctl) the effective buffer size that they
expect.
Initialize net.smc.[rw]mem from its own constant of 64kB, respectively.
Internal performance tests show that this value is a good compromise
between throughput/latency and memory consumption. Also, this decouples
it from any tuning that was done to net.ipv4.tcp_[rw]mem[1] before the
module for SMC protocol was loaded. Check that no more than INT_MAX / 2
is assigned to net.smc.[rw]mem, in order to avoid any overflow condition
when that is doubled for use in sk_sndbuf or sk_rcvbuf.
While at it, drop the confusing sk_buf_size variable from
__smc_buf_create and name "compressed" buffer size variables more
consistently.
Background:
Before the commit mentioned above, SMC's buffer allocator in
__smc_buf_create() always used half of the sockets' sk_rcvbuf/sk_sndbuf
value as initial value to search for appropriate buffers. If the search
resorted to using a bigger buffer when all buffers of the specified
size were busy, the duplicate of the used effective buffer size is
stored back to sk_rcvbuf/sk_sndbuf.
When available, buffers of exactly the size that a user had specified as
input to setsockopt() were used, despite setsockopt()'s documentation in
"man 7 socket" talking of a mandatory duplication:
[...]
SO_SNDBUF
Sets or gets the maximum socket send buffer in bytes.
The kernel doubles this value (to allow space for book‐
keeping overhead) when it is set using setsockopt(2),
and this doubled value is returned by getsockopt(2).
The default value is set by the
/proc/sys/net/core/wmem_default file and the maximum
allowed value is set by the /proc/sys/net/core/wmem_max
file. The minimum (doubled) value for this option is
2048.
[...]
Fixes: 0227f058aa ("net/smc: Unbind r/w buffer size from clcsock and make them tunable")
Co-developed-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
sfc: basic conntrack offload
Support offloading tracked connections and matching against them in
TC chains on the PF and on representors.
Later patch serieses will add NAT and conntrack-on-tunnel-netdevs;
keep it simple for now.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the (comparatively) simple case of a -trk rule on an efx netdev
(i.e. not a tunnel decap rule) with ct and goto chain actions.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse ct_state trk/est, mark and zone out of flower keys, and plumb
them through to the hardware, performing some minor translations.
Nothing can actually hit them yet as we're not offloading any DO_CT
actions.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Map it to an 8-bit recirc_id for use by the hardware.
Currently nothing in the driver is offloading 'goto chain' actions,
so these rules cannot yet be hit.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No handling yet for FLOW_ACTION_MANGLE (NAT or NAPT) actions.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Translate from software struct efx_tc_ct_entry objects to the key
and response bitstrings, and implement insertion and removal of
these entries from the hardware table.
Callers of these functions will be added in subsequent patches.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bind a stub callback to the netfilter flow table.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to the connection tracking table in EF100 hardware is through
a "generic" table mechanism, whereby a firmware call at probe time
gives the driver a description of the field widths and offsets, so
that the driver can then construct key and response bitstrings at
runtime.
Probe the NIC for this information and populate the needed metadata
into a new meta_ct field of struct efx_tc_state.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Identify and print the error source before rebooting the board due to an l3
timeout error. This is helpful when debugging, e.g. via serial.
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Message-ID: <20230801192240.1063764-1-absicsz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ACPI thermal driver uses acpi_bus_attach_private_data() to attach
the thermal zone object to the ACPI handle of the thermal zone and
acpi_bus_detach_private_data() to clean that up, but it never uses
acpi_bus_get_private_data() to retrieve that object.
Drop the unneded acpi_bus_attach_private_data() and
acpi_bus_detach_private_data() calls from the ACPI thermal driver and
clean up the related code.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Vladimir Oltean says:
====================
Fix ENETC probing after 6fffbc7ae1 ("PCI: Honor firmware's device disabled status")
I'm not sure who should take this patch set (net maintainers or PCI
maintainers). Everyone could pick up just their part, and that would
work (no compile time dependencies). However, the entire series needs
ACK from both sides and Rob for sure.
v1 at:
https://lore.kernel.org/netdev/20230521115141.2384444-1-vladimir.oltean@nxp.com/
====================
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6fffbc7ae1 ("PCI: Honor firmware's device disabled
status"), this is redundant and does nothing, because enetc_pf_probe()
no longer even gets called.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workaround implemented in commit 3222b5b613 ("net: enetc:
initialize RFS/RSS memories for unused ports too") is no longer
effective after commit 6fffbc7ae1 ("PCI: Honor firmware's device
disabled status"). Thus, it has introduced a regression and we see AER
errors being reported again:
$ ip link set sw2p0 up && dhclient -i sw2p0 && ip addr show sw2p0
fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode
fsl_enetc 0000:00:00.2 eno2: Link is Up - 2.5Gbps/Full - flow control rx/tx
mscc_felix 0000:00:00.5 swp2: configuring for fixed/sgmii link mode
mscc_felix 0000:00:00.5 swp2: Link is Up - 1Gbps/Full - flow control off
sja1105 spi2.2 sw2p0: configuring for phy/rgmii-id link mode
sja1105 spi2.2 sw2p0: Link is Up - 1Gbps/Full - flow control off
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
pcieport 0000:00:1f.0: AER: can't find device of ID0000
Rob's suggestion is to reimplement the enetc driver workaround as a
PCI fixup, and to modify the PCI core to run the fixups for all PCI
functions. This change handles the first part.
We refactor the common code in enetc_psi_create() and enetc_psi_destroy(),
and use the PCI fixup only for those functions for which enetc_pf_probe()
won't get called. This avoids some work being done twice for the PFs
which are enabled.
Fixes: 6fffbc7ae1 ("PCI: Honor firmware's device disabled status")
Link: https://lore.kernel.org/netdev/CAL_JsqLsVYiPLx2kcHkDQ4t=hQVCR7NHziDwi9cCFUFhx48Qow@mail.gmail.com/
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit has broken probing on
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi when &enetc_port0
(PCI function 0) has status = "disabled".
Background: pci_scan_slot() has logic to say that if the function 0 of a
device is absent, the entire device is absent and we can skip the other
functions entirely. Traditionally, this has meant that
pci_bus_read_dev_vendor_id() returns an error code for that function.
However, since the blamed commit, there is an extra confounding
condition: function 0 of the device exists and has a valid vendor id,
but it is disabled in the device tree. In that case, pci_scan_slot()
would incorrectly skip the entire device instead of just that function.
In the case of NXP LS1028A, status = "disabled" does not mean that the
PCI function's config space is not available for reading. It is, but the
Ethernet port is just not functionally useful with a particular SerDes
protocol configuration (0x9999) due to pinmuxing constraints of the Soc.
So, pci_scan_slot() skips all other functions on the ENETC ECAM
(enetc_port1, enetc_port2, enetc_mdio_pf3 etc) when just enetc_port0 had
to not be probed.
There is an additional regression introduced by the change, caused by
its fundamental premise. The enetc driver needs to run code for all PCI
functions, regardless of whether they're enabled or not in the device
tree. That is no longer possible if the driver's probe function is no
longer called. But Rob recommends that we move the of_device_is_available()
detection to dev->match_driver, and this makes the PCI fixups still run
on all functions, while just probing drivers for those functions that
are enabled. So, a separate change in the enetc driver will have to move
the workarounds to a PCI fixup.
Fixes: 6fffbc7ae1 ("PCI: Honor firmware's device disabled status")
Link: https://lore.kernel.org/netdev/CAL_JsqLsVYiPLx2kcHkDQ4t=hQVCR7NHziDwi9cCFUFhx48Qow@mail.gmail.com/
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for assigning some inode space to extended attributes,
keep track of free_ispace instead of number of free_inodes: as if one
tmpfs inode (and accompanying dentry) occupies very approximately 1KiB.
Unsigned long is large enough for free_ispace, on 64-bit and on 32-bit:
but take care to enforce the maximum. And fix the nr_blocks maximum on
32-bit: S64_MAX would be too big for it there, so say LONG_MAX instead.
Delete the incorrect limited<->unlimited blocks/inodes comment above
shmem_reconfigure(): leave it to the error messages below to describe.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Message-Id: <4fe1739-d9e7-8dfd-5bce-12e7339711da@google.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
tmpfs wants to support limited user extended attributes, but kernfs
(or cgroupfs, the only kernfs with KERNFS_ROOT_SUPPORT_USER_XATTR)
already supports user extended attributes through simple xattrs: but
limited by a policy (128KiB per inode) too liberal to be used on tmpfs.
To allow a different limiting policy for tmpfs, without affecting the
policy for kernfs, change simple_xattr_set() to return the replaced or
removed xattr (if any), leaving the caller to update their accounting
then free the xattr (by simple_xattr_free(), renamed from the static
free_simple_xattr()).
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Message-Id: <158c6585-2aa7-d4aa-90ff-f7c3f8fe407c@google.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
A while ago we received the following report:
"The other outstanding issue I noticed comes from the fact that
fsconfig syscalls may occur in a different userns than that which
called fsopen. That means that resolving the uid/gid via
current_user_ns() can save a kuid that isn't mapped in the associated
namespace when the filesystem is finally mounted. This means that it
is possible for an unprivileged user to create files owned by any
group in a tmpfs mount (since we can set the SUID bit on the tmpfs
directory), or a tmpfs that is owned by any user, including the root
group/user."
The contract for {g,u}id mount options and {g,u}id values in general set
from userspace has always been that they are translated according to the
caller's idmapping. In so far, tmpfs has been doing the correct thing.
But since tmpfs is mountable in unprivileged contexts it is also
necessary to verify that the resulting {k,g}uid is representable in the
namespace of the superblock to avoid such bugs as above.
The new mount api's cross-namespace delegation abilities are already
widely used. After having talked to a bunch of userspace this is the
most faithful solution with minimal regression risks. I know of one
users - systemd - that makes use of the new mount api in this way and
they don't set unresolable {g,u}ids. So the regression risk is minimal.
Link: https://lore.kernel.org/lkml/CALxfFW4BXhEwxR0Q5LSkg-8Vb4r2MONKCcUCVioehXQKr35eHg@mail.gmail.com
Fixes: f32356261d ("vfs: Convert ramfs, shmem, tmpfs, devtmpfs, rootfs to use the new mount API")
Reviewed-by: "Seth Forshee (DigitalOcean)" <sforshee@kernel.org>
Reported-by: Seth Jenkins <sethjenkins@google.com>
Message-Id: <20230801-vfs-fs_context-uidgid-v1-1-daf46a050bbf@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Commit "shmem: fix quota lock nesting in huge hole handling" was not so
good: Smatch caught shmem_recalc_inode()'s shmem_inode_unacct_blocks()
descending into quota_send_warning(): where blocking GFP_NOFS is used,
yet shmem_recalc_inode() is called holding the shmem inode's info->lock.
Yes, both __dquot_alloc_space() and __dquot_free_space() are commented
"This operation can block, but only after everything is updated" - when
calling flush_warnings() at the end - both its print_warning() and its
quota_send_warning() may block.
Rework shmem_recalc_inode() to take the shmem inode's info->lock inside,
and drop it before calling shmem_inode_unacct_blocks().
And why were the spin_locks disabling interrupts? That was just a relic
from when shmem_charge() and shmem_uncharge() were called while holding
i_pages xa_lock: stop disabling interrupts for info->lock now.
To help stop me from making the same mistake again, add a might_sleep()
into shmem_inode_acct_block() and shmem_inode_unacct_blocks(); and those
functions have grown, so let the compiler decide whether to inline them.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-fsdevel/ffd7ca34-7f2a-44ee-b05d-b54d920ce076@moroto.mountain/
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <29f48045-2cb5-7db-ecf1-72462f1bef5@google.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Since offset_iterate_dir() does not walk the parent's d_subdir list
nor does it manipulate the parent's d_child, there doesn't seem to
be a reason to hold the parent's d_lock. The offset_ctx's xarray can
be sufficiently protected with just the RCU read lock.
Flame graph data captured during the git regression run shows a
20% reduction in CPU cycles consumed in offset_find_next().
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202307171640.e299f8d5-oliver.sang@intel.com
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Message-Id: <169030957098.157536.9938425508695693348.stgit@manet.1015granger.net>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Tie the dynamically-allocated xarray locks into a single class so
contention on the directory offset xarrays can be observed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Message-Id: <169020933088.160441.9405180953116076087.stgit@manet.1015granger.net>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The current cursor-based directory offset mechanism doesn't work
when a tmpfs filesystem is exported via NFS. This is because NFS
clients do not open directories. Each server-side READDIR operation
has to open the directory, read it, then close it. The cursor state
for that directory, being associated strictly with the opened
struct file, is thus discarded after each NFS READDIR operation.
Directory offsets are cached not only by NFS clients, but also by
user space libraries on those clients. Essentially there is no way
to invalidate those caches when directory offsets have changed on
an NFS server after the offset-to-dentry mapping changes. Thus the
whole application stack depends on unchanging directory offsets.
The solution we've come up with is to make the directory offset for
each file in a tmpfs filesystem stable for the life of the directory
entry it represents.
shmem_readdir() and shmem_dir_llseek() now use an xarray to map each
directory offset (an loff_t integer) to the memory address of a
struct dentry.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Message-Id: <168814734331.530310.3911190551060453102.stgit@manet.1015granger.net>
Signed-off-by: Christian Brauner <brauner@kernel.org>
De-duplicate the error handling paths. No change in behavior is
expected.
Suggested-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Message-Id: <168814733654.530310.9958360833543413152.stgit@manet.1015granger.net>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Create a vector of directory operations in fs/libfs.c that handles
directory seeks and readdir via stable offsets instead of the
current cursor-based mechanism.
For the moment these are unused.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Message-Id: <168814732984.530310.11190772066786107220.stgit@manet.1015granger.net>
Signed-off-by: Christian Brauner <brauner@kernel.org>
i_pages lock nests inside i_lock, but shmem_charge() and shmem_uncharge()
were being called from THP splitting or collapsing while i_pages lock was
held, and now go on to call dquot_alloc_block_nodirty() which takes
i_lock to update i_blocks.
We may well want to take i_lock out of this path later, in the non-quota
case even if it's left in the quota case (or perhaps use i_lock instead
of shmem's info->lock throughout); but don't get into that at this time.
Move the shmem_charge() and shmem_uncharge() calls out from under i_pages
lock, accounting the full batch of holes in a single call.
Still pass the pages argument to shmem_uncharge(), but it happens now to
be unused: shmem_recalc_inode() is designed to account for clean pages
freed behind shmem's back, so it gets the accounting right by itself;
then the later call to shmem_inode_unacct_blocks() led to imbalance
(that WARN_ON(inode->i_blocks) in shmem_evict_inode()).
Reported-by: syzbot+38ca19393fb3344f57e6@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/lkml/0000000000008e62f40600bfe080@google.com/
Reported-by: syzbot+440ff8cca06ee7a1d4db@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/lkml/00000000000076a7840600bfb6e8@google.com/
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Message-Id: <20230725144510.253763-8-cem@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Allow system administrator to set default global quota limits at tmpfs
mount time.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230725144510.253763-7-cem@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Now the basic infra-structure is in place, enable quota support for tmpfs.
This offers user and group quotas to tmpfs (project quotas will be added
later). Also, as other filesystems, the tmpfs quota is not supported
within user namespaces yet, so idmapping is not translated.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230725144510.253763-6-cem@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add new shmem quota format, its quota_format_ops together with
dquot_operations
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230725144510.253763-5-cem@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Currently we check whether superblock has ->quota_read and ->quota_write
operations to check whether filesystem supports quotas. However for
example for shmfs we will not read or write dquots so check whether
quota operations are set in the superblock instead.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Message-Id: <20230725144510.253763-4-cem@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Make shmem_get_inode() return ERR_PTR instead of NULL on error. This will be
useful later when we introduce quota support.
There should be no functional change.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230725144510.253763-3-cem@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Make shmem_inode_acct_block() return proper error code instead of bool.
This will be useful later when we introduce quota support.
There should be no functional change.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230725144510.253763-2-cem@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to drop the "now" argument from the
update_time operation. Have btrfs_update_time use the new
inode_update_timestamps helper to fetch a new timestamp and update it
properly.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230807-mgctime-v7-4-d1dec143a704@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In future patches we're going to change how the ctime is updated
to keep track of when it has been queried. The way that the update_time
operation works (and a lot of its callers) make this difficult, since
they grab a timestamp early and then pass it down to eventually be
copied into the inode.
All of the existing update_time callers pass in the result of
current_time() in some fashion. Drop the "time" parameter from
generic_update_time, and rework it to fetch its own timestamp.
This change means that an update_time could fetch a different timestamp
than was seen in inode_needs_update_time. update_time is only ever
called with one of two flag combinations: Either S_ATIME is set, or
S_MTIME|S_CTIME|S_VERSION are set.
With this change we now treat the flags argument as an indicator that
some value needed to be updated when last checked, rather than an
indication to update specific timestamps.
Rework the logic for updating the timestamps and put it in a new
inode_update_timestamps helper that other update_time routines can use.
S_ATIME is as treated as we always have, but if any of the other three
are set, then we attempt to update all three.
Also, some callers of generic_update_time need to know what timestamps
were actually updated. Change it to return an S_* flag mask to indicate
that and rework the callers to expect it.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230807-mgctime-v7-3-d1dec143a704@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
generic_fillattr just fills in the entire stat struct indiscriminately
today, copying data from the inode. There is at least one attribute
(STATX_CHANGE_COOKIE) that can have side effects when it is reported,
and we're looking at adding more with the addition of multigrain
timestamps.
Add a request_mask argument to generic_fillattr and have most callers
just pass in the value that is passed to getattr. Have other callers
(e.g. ksmbd) just pass in STATX_BASIC_STATS. Also move the setting of
STATX_CHANGE_COOKIE into generic_fillattr.
Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: "Paulo Alcantara (SUSE)" <pc@manguebit.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Message-Id: <20230807-mgctime-v7-2-d1dec143a704@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
An inode with no superblock? Unpossible!
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230807-mgctime-v7-1-d1dec143a704@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
get-reg-list test is used to check for KVM registers regressions
during VM migration which happens when destination host kernel
missing registers that the source host kernel has. The blessed
list registers was created by running on v6.5-rc3
Signed-off-by: Haibo Xu <haibo1.xu@intel.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
KVM_GET_REG_LIST API will return all registers that are available to
KVM_GET/SET_ONE_REG APIs. It's very useful to identify some platform
regression issue during VM migration.
Since this API was already supported on arm64, it is straightforward
to enable it on riscv with similar code structure.
Signed-off-by: Haibo Xu <haibo1.xu@intel.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Add new skips_set members to vcpu_reg_sublist so as to skip
set operation on some registers.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Haibo Xu <haibo1.xu@intel.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Only do the get/set tests on present and blessed registers
since we don't know the capabilities of any new ones.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Haibo Xu <haibo1.xu@intel.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
No functional changes. Just move the finalize_vcpu call back to
run_test and do weak function trick to prepare for the opration
in riscv.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Haibo Xu <haibo1.xu@intel.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
No functional changes. Just move the reject_set check logic to a
function so we can check for a specific errno. This is a preparation
for support reject_set in riscv.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Haibo Xu <haibo1.xu@intel.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Add some unfortunate #ifdeffery to ensure the common get-reg-list.c
can be compiled and run with other architectures. The next
architecture to support get-reg-list should now only need to provide
$(ARCH_DIR)/get-reg-list.c where arch-specific print_reg() and
vcpu_configs[] get defined.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Haibo Xu <haibo1.xu@intel.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
