The SYSTEM_SLEEP_PM_OPS() allows us to get rid of '#ifdef
CONFIG_PM_SLEEP', as talked about in commit 1a3c7bb088 ("PM: core:
Add new *_PM_OPS macros, deprecate old ones").
This change is expected to have no functional effect.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727101636.v4.5.Ib2a2865bd3c0b068432259dfc7d76cebcbb512be@changeid
Inform fw_devlink of the fact that a panel follower (like a
touchscreen) is effectively a consumer of the panel from the purposes
of fw_devlink.
NOTE: this patch isn't required for correctness but instead optimizes
probe order / helps avoid deferrals.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727101636.v4.4.Ibf8e1342b5b7906279db2365aca45e6253857bb3@changeid
These days, it's fairly common to see panels that have touchscreens
attached to them. The panel and the touchscreen can somewhat be
thought of as totally separate devices and, historically, this is how
Linux has treated them. However, treating them as separate isn't
necessarily the best way to model the two devices, it was just that
there was no better way. Specifically, there is little practical
reason to have the touchscreen powered on when the panel is turned
off, but if we model the devices separately we have no way to keep the
two devices' power states in sync with each other.
The issue described above makes it sound as if the problem here is
just about efficiency. We're wasting power keeping the touchscreen
powered up when the screen is off. While that's true, the problem can
go deeper. Specifically, hardware designers see that there's no reason
to have the touchscreen on while the screen is off and then build
hardware assuming that software would never turn the touchscreen on
while the screen is off.
In the very simplest case of hardware designs like this, the
touchscreen and the panel share some power rails. In most cases, this
turns out not to be terrible and is, again, just a little less
efficient. Specifically if we tell Linux that the touchscreen and the
panel are using the same rails then Linux will keep the rails on when
_either_ device is turned on. That ends to work OK-ish, but now if you
turn the panel off not only will the touchscreen remain powered, but
the power rails for the panel itself won't be switched off, burning
extra power.
The above two inefficiencies are _extra_ minor when you consider the
fact that laptops rarely spend much time with the screen off. The main
use case would be when an external screen (and presumably a power
supply) is attached.
Unfortunately, it gets worse from here. On sc7180-trogdor-homestar,
for instance, the display's TCON (timing controller) sometimes crashes
if you don't power cycle it whenever you stop and restart the video
stream (like during a modeset). The touchscreen keeping the power
rails on causes real problems. One proposal in the homestar timeframe
was to move the touchscreen to an always-on rail, dedicating the main
power rail to the panel. That caused _different_ problems as talked
about in commit 557e05fa9f ("HID: i2c-hid: goodix: Stop tying the
reset line to the regulator"). The end result of all of this was to
add an extra regulator to the board, increasing cost.
Recently, Cong Yang posted a patch [1] where things are even worse.
The panel and touch controller on that system seem even more
intimately tied together and really can't be thought of separately.
To address this issue, let's start allowing devices to register
themselves as "panel followers". These devices will get called after a
panel has been powered on and before a panel is powered off. This
makes the panel the primary device in charge of the power state, which
matches how userspace uses it.
The panel follower API should be fairly straightforward to use. The
current code assumes that panel followers are using device tree and
have a "panel" property pointing to the panel to follow. More
flexibility and non-DT implementations could be added as needed.
Right now, panel followers can follow the prepare/unprepare functions.
There could be arguments made that, instead, they should follow
enable/disable. I've chosen prepare/unprepare for now since those
functions are guaranteed to power up/power down the panel and it seems
better to start the process earlier.
A bit of explaining about why this is a roll-your-own API instead of
using something more standard:
1. In standard APIs in Linux, parent devices are automatically powered
on when a child needs power. Applying that here, it would mean that
we'd force the panel on any time someone was listening to the
touchscreen. That, unfortunately, would have broken homestar's need
(if we hadn't changed the hardware, as per above) where the panel
absolutely needs to be able to power cycle itself. While one could
argue that homestar is broken hardware and we shouldn't have the
API do backflips for it, _officially_ the eDP timing guidelines
agree with homestar's needs and the panel power sequencing diagrams
show power going off. It's nice to be able to support this.
2. We could, conceibably, try to add a new flag to device_link causing
the parent to be in charge of power. Then we could at least use
normal pm_runtime APIs. This sounds great, except that we run into
problems with initial probe. As talked about in the later patch
("HID: i2c-hid: Support being a panel follower") the initial power
on of a panel follower might need to do things (like add
sub-devices) that aren't allowed in a runtime_resume function.
The above complexities explain why this API isn't using common
functions. That being said, this patch is very small and
self-contained, so if someone was later able to adapt it to using more
common APIs while solving the above issues then that could happen in
the future.
[1] https://lore.kernel.org/r/20230519032316.3464732-1-yangcong5@huaqin.corp-partner.google.com
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727101636.v4.3.Icd5f96342d2242051c754364f4bee13ef2b986d4@changeid
In a whole pile of panel drivers, we have code to make the
prepare/unprepare/enable/disable callbacks behave as no-ops if they've
already been called. It's silly to have this code duplicated
everywhere. Add it to the core instead so that we can eventually
delete it from all the drivers. Note: to get some idea of the
duplicated code, try:
git grep 'if.*>prepared' -- drivers/gpu/drm/panel
git grep 'if.*>enabled' -- drivers/gpu/drm/panel
NOTE: arguably, the right thing to do here is actually to skip this
patch and simply remove all the extra checks from the individual
drivers. Perhaps the checks were needed at some point in time in the
past but maybe they no longer are? Certainly as we continue
transitioning over to "panel_bridge" then we expect there to be much
less variety in how these calls are made. When we're called as part of
the bridge chain, things should be pretty simple. In fact, there was
some discussion in the past about these checks [1], including a
discussion about whether the checks were needed and whether the calls
ought to be refcounted. At the time, I decided not to mess with it
because it felt too risky.
Looking closer at it now, I'm fairly certain that nothing in the
existing codebase is expecting these calls to be refcounted. The only
real question is whether someone is already doing something to ensure
prepare()/unprepare() match and enabled()/disable() match. I would say
that, even if there is something else ensuring that things match,
there's enough complexity that adding an extra bool and an extra
double-check here is a good idea. Let's add a drm_warn() to let people
know that it's considered a minor error to take advantage of
drm_panel's double-checking but we'll still make things work fine.
We'll also add an entry to the official DRM todo list to remove the
now pointless check from the panels after this patch lands and,
eventually, fixup anyone who is triggering the new warning.
[1] https://lore.kernel.org/r/20210416153909.v4.27.I502f2a92ddd36c3d28d014dd75e170c2d405a0a5@changeid
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727101636.v4.2.I59b417d4c29151cc2eff053369ec4822b606f375@changeid
As talked about in the patch ("drm/panel: Add a way for other devices
to follow panel state"), touchscreens that are connected to panels are
generally expected to be power sequenced together with the panel
they're attached to. Today, nothing provides information allowing you
to find out that a touchscreen is connected to a panel. Let's add a
phandle for this.
The proerty is added to the generic touchscreen bindings and then
enabled in the bindings for the i2c-hid backed devices. This can and
should be added for other touchscreens in the future, but for now
let's start small.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Benjamin Tissoires <bentiss@kernel.org>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727101636.v4.1.Id68e30343bb1e11470582a9078b086176cfec46b@changeid
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
Lots of small cleanups coming from Bard Liao and Charles Keepax for
SoundWire platforms, and minor additions for RVPs and Chromebooks.
The trailing array member of struct tx_buf was defined as a 1-element
array, but used as a flexible array. This was resulting in build warnings:
In function 'fortify_memset_chk',
inlined from 'memset_io' at /kisskb/src/arch/mips/include/asm/io.h:486:2,
inlined from 'build_auth_frame' at /kisskb/src/drivers/net/wireless/legacy/ray_cs.c:2697:2:
/kisskb/src/include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning:
detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Replace it with an actual flexible array. Binary difference comparison
shows a single change in output:
│ drivers/net/wireless/legacy/ray_cs.c:883
│ lea 0x1c(%rbp),%r13d
│ - cmp $0x7c3,%r13d
│ + cmp $0x7c4,%r13d
This is from:
if (len + TX_HEADER_LENGTH > TX_BUF_SIZE) {
specifically:
#define TX_BUF_SIZE (2048 - sizeof(struct tx_msg))
This appears to have been originally buggy, so the change is correct.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/all/88f83d73-781d-bdc-126-aa629cb368c@linux-m68k.org
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230728231245.never.309-kees@kernel.org
With commit 099f26f22f ("integrity: machine keyring CA
configuration"), users are able to add custom IMA CA keys via
MOK. This allows users to sign their own IMA polices without
recompiling the kernel. For the sake of security, mandate signed IMA
policy when UEFI secure boot is enabled.
Note this change may affect existing users/tests i.e users won't be able
to load an unsigned IMA policy when the IMA architecture specific policy
is configured and UEFI secure boot is enabled.
Suggested-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Coiby Xu <coxu@redhat.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Commit 273df864cf ("ima: Check against blacklisted hashes for files with
modsig") introduced an appraise_flag option for referencing the blacklist
keyring. Any matching binary found on this keyring fails signature
validation. This flag only works with module appended signatures.
An important part of a PKI infrastructure is to have the ability to do
revocation at a later time should a vulnerability be found. Expand the
revocation flag usage to all appraisal functions. The flag is now
enabled by default. Setting the flag with an IMA policy has been
deprecated. Without a revocation capability like this in place, only
authenticity can be maintained. With this change, integrity can now be
achieved with digital signature based IMA appraisal.
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Nayna Jain <nayna@linux.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
The enabled field of struct acpi_thermal_active is only updated and never
read, so drop it along with the related code.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit fcea0ccf4f ("ACPI: bus: Consolidate all arm specific
initialisation into acpi_arm_init()") moved all of the ARM-specific
initialization into acpi_arm_init(). However, acpi_amba.c being outside
of drivers/acpi/arm64 got ignored and hence acpi_amba_init() was not
moved into acpi_arm_init().
Move the AMBA platform bus support into arm64 specific folder and make
acpi_amba_init() part of acpi_arm_init().
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the memory allocation of rp->domains in rapl_detect_domains(), there
is an additional memory of struct rapl_domain allocated, optimize the
code here to save sizeof(struct rapl_domain) bytes of memory.
Test in Intel NUC (i5-1135G7).
Signed-off-by: xiongxin <xiongxin@kylinos.cn>
Tested-by: xiongxin <xiongxin@kylinos.cn>
Reviewed-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Depends on the interface used, the RAPL registers can be either MSR
indexes or memory mapped IO addresses. Current RAPL common code uses u64
to save both MSR and memory mapped IO registers. With this, when
handling register address with an __iomem annotation, it triggers a
sparse warning like below:
sparse warnings: (new ones prefixed by >>)
>> drivers/powercap/intel_rapl_tpmi.c:141:41: sparse: sparse: incorrect type in initializer (different address spaces) @@ expected unsigned long long [usertype] *tpmi_rapl_regs @@ got void [noderef] __iomem * @@
drivers/powercap/intel_rapl_tpmi.c:141:41: sparse: expected unsigned long long [usertype] *tpmi_rapl_regs
drivers/powercap/intel_rapl_tpmi.c:141:41: sparse: got void [noderef] __iomem *
Fix the problem by using a union to save the registers instead.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307031405.dy3druuy-lkp@intel.com/
Tested-by: Wang Wendy <wendy.wang@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
GCC11 provides an '-fanalyzer' static analysis option which does not
provide too many false-positives. This patch cleans-up known
problematic code paths to help enable this capability in CI. We've
used this for about a month already.
This cpupower update for Linux 6.6-rc1 consists of 2 fixes and
enhancements to add support for amd-pstate active mode driver,
amd_pstate mode change, EPP value change, turbo-boost support,
and is_valid_path API.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPZKym/RZuOCGeA/kCwJExA0NQxwFAmTIGVcACgkQCwJExA0N
QxxBdw//QNFfK4CMRagUanhvYHYq0KTK0aAZv6cMR1GlhtLsBzPCKsTSQwTULUZD
PmFzuQLfLN9fcBcK8X+icFbaAJztLcxpm+97kWqLe0di6N96UDCrBgv1H/CHB5Q4
UpTCoQPAVRbPK36/7V0jDiNjROL+/maUjSHYaZiNvzh8ismt/4h4nK0eJdMIABId
8nFkM8gM6q48nq8G0HXwtzTfTwpfF51qXM2SbEe6KrhfLai9epn/WwXWASdvRMPF
8JGscK0lZlEQCf+r1PS75CacjZzqiFNEM8W3ItzoCySF2s607N9S7cpBZpgpwwdY
aYesRMRwASNXfLsKtehfssi3Yevc6WtAQvKFexieQNy5M738z06SALU6JOWk2NLv
NqwUxTK2bFLyzgdDuAClb7R0nEl5IH8UnkoHtR+vw6ZfhfQgQuKRrewKjoWmwcao
R5XuSHILQD5zFtjq/scRUiHqyu2ywZy4MCfb9lz43hTJlv+1go6+fpBLsVoOu/zn
RjFDlyra+tngWjlxQR1VScXbVEN1plODg1CTXEvLbnDM/CH+1fmaSRoVJ4Wyznpd
gvJP8ADUiRH4IcXv4XW3p0M+EiRbg5oVNqiMUjEsiCLh8azwhadf/NI2u06poJr2
tUPD7wkp3Qw/J/oT2XS3y79tPctLmrJkrjK6xHq+RBSousvn750=
=KeYi
-----END PGP SIGNATURE-----
Merge tag 'linux-cpupower-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux
Merge cpupower utility update for 6.6-rc1 from Shuah Khan:
"This cpupower update for Linux 6.6-rc1 consists of 2 fixes and
enhancements to add support for amd-pstate active mode driver,
amd_pstate mode change, EPP value change, turbo-boost support,
and is_valid_path API."
* tag 'linux-cpupower-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux:
cpupower: Fix cpuidle_set to accept only numeric values for idle-set operation.
cpupower: Add turbo-boost support in cpupower
cpupower: Add support for amd_pstate mode change
cpupower: Add EPP value change support
cpupower: Add is_valid_path API
cpupower: Recognise amd-pstate active mode driver
cpupower: Bump soname version
When booting on e6500 with an ELF v2 ABI kernel, the secondary threads do
not start correctly:
[ 0.051118] smp: Bringing up secondary CPUs ...
[ 5.072700] Processor 1 is stuck.
This occurs because the startup code is written to use function
descriptors when loading the entry point for the secondary threads. When
building with ELF v2 ABI there are no function descriptors, and the code
loads junk values for the entry point address.
Fix it by using ppc_function_entry() in C, and DOTSYM() in asm, both of
which work correctly for ELF v2 ABI as well as ELF v1 ABI kernels.
Fixes: 8c5fa3b5c4 ("powerpc/64: Make ELFv2 the default for big-endian builds")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230801102650.48705-1-mpe@ellerman.id.au
In destruction flow, the assignment of NULL to xso->dev
caused to skip of xfrm_dev_state_free() call, which was
called in xfrm_state_put(to_put) routine.
Instead of open-coded variant of xfrm_dev_state_delete() and
xfrm_dev_state_free(), let's use them directly.
Fixes: f8a70afafc ("xfrm: add TX datapath support for IPsec packet offload mode")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The policy memory was released but not HW driver data. Add
call to xfrm_dev_policy_delete(), so drivers will have a chance
to release their resources.
Fixes: 919e43fad5 ("xfrm: add an interface to offload policy")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Convert for loop to dsa_for_each macro to save some redundant write on
unconnected/unused port and tidy things up.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230730074113.21889-5-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move qca8xxx hol fixup to separate function to tidy things up and to
permit using a more efficent loop in future patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230730074113.21889-4-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In preparation for multi-CPU support, set CPU port LOOKUP MEMBER outside
the port loop and setup the LOOKUP MEMBER mask for user ports only to
the first CPU port.
This is to handle flooding condition where every CPU port is set as
target and prevent packet duplication for unknown frames from user ports.
Secondary CPU port LOOKUP MEMBER mask will be setup later when
port_change_master will be implemented.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230730074113.21889-3-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Currently this is not the case for qca8k where learning is enabled
unconditionally in qca8k_setup for every user port.
Handle ports configured in standalone mode by making the learning
configurable and not enabling it by default.
Implement .port_pre_bridge_flags and .port_bridge_flags dsa ops to
enable learning for bridge that request it and tweak
.port_stp_state_set to correctly disable learning when port is
configured in standalone mode.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230730074113.21889-2-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently checksum is recalculated and dsa tag stripped even if we later
don't find the dev.
To improve code, exit early if we don't find the dev and skip additional
operation on the skb since it will be freed anyway.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230730074113.21889-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Infinite waits for completion of GPU activity have been observed in CI,
mostly inside __i915_active_wait(), triggered by igt@gem_barrier_race or
igt@perf@stress-open-close. Root cause analysis, based of ftrace dumps
generated with a lot of extra trace_printk() calls added to the code,
revealed loops of request dependencies being accidentally built,
preventing the requests from being processed, each waiting for completion
of another one's activity.
After we substitute a new request for a last active one tracked on a
timeline, we set up a dependency of our new request to wait on completion
of current activity of that previous one. While doing that, we must take
care of keeping the old request still in memory until we use its
attributes for setting up that await dependency, or we can happen to set
up the await dependency on an unrelated request that already reuses the
memory previously allocated to the old one, already released. Combined
with perf adding consecutive kernel context remote requests to different
user context timelines, unresolvable loops of await dependencies can be
built, leading do infinite waits.
We obtain a pointer to the previous request to wait upon when we
substitute it with a pointer to our new request in an active tracker,
e.g. in intel_timeline.last_request. In some processing paths we protect
that old request from being freed before we use it by getting a reference
to it under RCU protection, but in others, e.g. __i915_request_commit()
-> __i915_request_add_to_timeline() -> __i915_request_ensure_ordering(),
we don't. But anyway, since the requests' memory is SLAB_FAILSAFE_BY_RCU,
that RCU protection is not sufficient against reuse of memory.
We could protect i915_request's memory from being prematurely reused by
calling its release function via call_rcu() and using rcu_read_lock()
consequently, as proposed in v1. However, that approach leads to
significant (up to 10 times) increase of SLAB utilization by i915_request
SLAB cache. Another potential approach is to take a reference to the
previous active fence.
When updating an active fence tracker, we first lock the new fence,
substitute a pointer of the current active fence with the new one, then we
lock the substituted fence. With this approach, there is a time window
after the substitution and before the lock when the request can be
concurrently released by an interrupt handler and its memory reused, then
we may happen to lock and return a new, unrelated request.
Always get a reference to the current active fence first, before
replacing it with a new one. Having it protected from premature release
and reuse, lock it and then replace with the new one but only if not
yet signalled via a potential concurrent interrupt nor replaced with
another one by a potential concurrent thread, otherwise retry, starting
from getting a reference to the new current one. Adjust users to not
get a reference to the previous active fence themselves and always put the
reference got by __i915_active_fence_set() when no longer needed.
v3: Fix lockdep splat reports and other issues caused by incorrect use of
try_cmpxchg() (use (cmpxchg() != prev) instead)
v2: Protect request's memory by getting a reference to it in favor of
delegating its release to call_rcu() (Chris)
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8211
Fixes: df9f85d858 ("drm/i915: Serialise i915_active_fence_set() with itself")
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.6+
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230720093543.832147-2-janusz.krzysztofik@linux.intel.com
(cherry picked from commit 946e047a3d)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Perform some refactoring with the purpose of keeping in one
single place all the operations around the aux table
invalidation.
With this refactoring add more engines where the invalidation
should be performed.
Fixes: 972282c4cf ("drm/i915/gen12: Add aux table invalidate for all engines")
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230725001950.1014671-8-andi.shyti@linux.intel.com
(cherry picked from commit 76ff7789d6)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
For platforms that use Aux CCS, wait for aux invalidation to
complete by checking the aux invalidation register bit is
cleared.
Fixes: 972282c4cf ("drm/i915/gen12: Add aux table invalidate for all engines")
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230725001950.1014671-7-andi.shyti@linux.intel.com
(cherry picked from commit d459c86f00)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Enable the CCS_FLUSH bit 13 in the control pipe for render and
compute engines in platforms starting from Meteor Lake (BSPEC
43904 and 47112).
For the copy engine add MI_FLUSH_DW_CCS (bit 16) in the command
streamer.
Fixes: 972282c4cf ("drm/i915/gen12: Add aux table invalidate for all engines")
Requires: 8da173db894a ("drm/i915/gt: Rename flags with bit_group_X according to the datasheet")
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Nirmoy Das <nirmoy.das@intel.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230725001950.1014671-6-andi.shyti@linux.intel.com
(cherry picked from commit b70df82b42)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
In preparation of the next patch align with the datasheet (BSPEC
47112) with the naming of the pipe control set of flag values.
The variable "flags" in gen12_emit_flush_rcs() is applied as a
set of flags called Bit Group 1.
Define also the Bit Group 0 as bit_group_0 where currently only
PIPE_CONTROL0_HDC_PIPELINE_FLUSH bit is set.
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230725001950.1014671-5-andi.shyti@linux.intel.com
(cherry picked from commit f2dcd21d5a)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
All memory traffic must be quiesced before requesting
an aux invalidation on platforms that use Aux CCS.
Fixes: 972282c4cf ("drm/i915/gen12: Add aux table invalidate for all engines")
Requires: a2a4aa0eef3b ("drm/i915: Add the gen12_needs_ccs_aux_inv helper")
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230725001950.1014671-4-andi.shyti@linux.intel.com
(cherry picked from commit ad8ebf1221)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We always assumed that a device might either have AUX or FLAT
CCS, but this is an approximation that is not always true, e.g.
PVC represents an exception.
Set the basis for future finer selection by implementing a
boolean gen12_needs_ccs_aux_inv() function that tells whether aux
invalidation is needed or not.
Currently PVC is the only exception to the above mentioned rule.
Requires: 059ae7ae2a1c ("drm/i915/gt: Cleanup aux invalidation registers")
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230725001950.1014671-3-andi.shyti@linux.intel.com
(cherry picked from commit c827655b87)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fix the 'NV' definition postfix that is supposed to be INV.
Take the chance to also order properly the registers based on
their address and call the GEN12_GFX_CCS_AUX_INV address as
GEN12_CCS_AUX_INV like all the other similar registers.
Remove also VD1, VD3 and VE1 registers that don't exist and add
BCS0 and CCS0.
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230725001950.1014671-2-andi.shyti@linux.intel.com
(cherry picked from commit 2f0b927d3c)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Pedro Tammela says:
====================
net/sched: improve class lifetime handling
Valis says[0]:
============
Three classifiers (cls_fw, cls_u32 and cls_route) always copy
tcf_result struct into the new instance of the filter on update.
This causes a problem when updating a filter bound to a class,
as tcf_unbind_filter() is always called on the old instance in the
success path, decreasing filter_cnt of the still referenced class
and allowing it to be deleted, leading to a use-after-free.
============
Turns out these could have been spotted easily with proper warnings.
Improve the current class lifetime with wrappers that check for
overflow/underflow.
While at it add an extack for when a class in use is deleted.
[0] https://lore.kernel.org/all/20230721174856.3045-1-sec@valis.email/
====================
Link: https://lore.kernel.org/r/20230728153537.1865379-1-pctammela@mojatatu.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add extack to warn that delete was rejected because
the class is still in use
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add extack to warn that delete was rejected because
the class is still in use
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add extack to warn that delete was rejected because
the class is still in use
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add extack to warn that delete was rejected because
the class is still in use
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The 'filter_cnt' counter is used to control a Qdisc class lifetime.
Each filter referecing this class by its id will eventually
increment/decrement this counter in their respective
'add/update/delete' routines.
As these operations are always serialized under rtnl lock, we don't
need an atomic type like 'refcount_t'.
It also means that we lose the overflow/underflow checks already
present in refcount_t, which are valuable to hunt down bugs
where the unsigned counter wraps around as it aids automated tools
like syzkaller to scream in such situations.
Wrap the open coded increment/decrement into helper functions and
add overflow checks to the operations.
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For current implementation of vmid allocation of arm smmu-v3, a per-smmu
devide bitmap of 64K bits(8K bytes) is allocated on behalf of possible VMID
range, which is two pages for some architectures. Besides that, its memory
consumption is 'static', despite of how many VMIDs are allocated actually.
That's memory inefficient and lack of scalability.
So an IDA based implementation is introduced to address this issue, which
is capable of self-expanding on the actual need of VMID allocation.
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/TYCP286MB2323E0C525FF9F94E3B07C7ACA35A@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Will Deacon <will@kernel.org>
A very basic debugging rule when a device is connected for the first
time is to access a read-only register which contains known data in
order to ensure the communication protocol is properly working. This
driver lacked any read helper which is often a critical piece for
speeding-up bring-ups.
Add a read helper and use it to verify the communication with the panel
is working as soon as possible in order to inform the user early if this
is not the case.
As this panel may work with no MISO line, the check is discarded in this
case. Upon error, we do not fail probing but just warn the user, in case
the DT description would be lacking the Rx bus width (which is likely on
old descriptions) in order to avoid breaking existing devices.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org> # no MISO line
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-20-sre@kernel.org
This panel from Emerging Display Technologies Corporation features an
ST7789V2 LCD controller panel inside which is almost identical to what
the Sitronix panel driver supports.
In practice, the module physical size is specific, and experiments show
that the display will malfunction if any of the following situation
occurs:
* Pixel clock is above 3MHz
* Pixel clock is not inverted
I could not properly identify the reasons behind these failures, scope
captures show valid input signals.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-19-sre@kernel.org
The Sitronix datasheet explains BIT(1) of the RGBCTRL register as the
DOTCLK/PCLK edge used to sample the data lines:
“0” The data is input on the positive edge of DOTCLK
“1” The data is input on the negative edge of DOTCLK
IOW, this bit implies a falling edge and not a high state. Correct the
definition to ease the comparison with the datasheet.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-18-sre@kernel.org
The Sitronix controller expects 9-bit words, provide this as default at
probe time rather than specifying this in each and every access.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-17-sre@kernel.org
The ST7789V LCD controller supports regular SPI wiring, as well as no Rx
data line at all. The operating system needs to know whether it can read
registers from the device or not. Let's detail this specific design
possibility by bounding the spi-rx-bus-width property.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-16-sre@kernel.org
The ST7789V LCD controller is also embedded in the ET028013DMA
panel. Add a compatible string to describe this other panel.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-15-sre@kernel.org
UNI-T UTi260b has a Inanbo T28CP45TN89 v17 panel. I could not find
proper documentation for the panel apart from a technical drawing, but
according to the vendor U-Boot it is based on a Sitronix st7789v chip.
I generated the init sequence by modifying the default one until proper
graphics output has been seen on the device.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-14-sre@kernel.org
Add polarity information via mode and bus flags, so that they are no
longer hardcoded and forward the information to the DRM stack. This is
required for adding panels with different settings.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-13-sre@kernel.org
While the default panel uses invert mode, some panels
require non-invert mode instead.
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-12-sre@kernel.org
