Add a cpumask for the DMC620 PMU. As it is an uncore PMU, perf
userspace tool only needs to open a single counter on the CPU
specified by the CPU mask for each event on a given DMC620 device.
Signed-off-by: Xin Yang <xin.yang@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20230613013423.2078397-1-xin.yang@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
When running as an unprivileged PV guest under Xen (not dom0), the
default MTRR memory type should be write-back.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20230615123959.12298-1-jgross@suse.com
Qoriq and related devices allow reading out state of GPIO set as output.
However, currently on driver's init, all outputs are configured as driven
low. So, any changes to GPIO confiuration will drive all pins (configured
as output) as output-low.
This patch latches state of output GPIOs before any GPIO configuration
takes place. This preserves any output settings done prior to loading
the driver (for example, by u-boot).
Signed-off-by: Michal Smulski <michal.smulski@ooma.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
SYSFS_PATH can be used locally and globally, especially that has
the same content.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for the BlueField-3 SoC GPIO driver.
This driver configures and handles GPIO interrupts. It also enables a user
to manipulate certain GPIO pins via libgpiod tools or other kernel drivers.
The usables pins are defined via the "gpio-reserved-ranges" property.
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Update the query struct such that secret-UVC related
information can be parsed.
Add sysfs files for these new values.
'supp_add_secret_req_ver' notes the supported versions for the
Add Secret UVC. Bit 0 indicates that version 0x100 is supported,
bit 1 indicates 0x200, and so on.
'supp_add_secret_pcf' notes the supported plaintext flags for
the Add Secret UVC.
'supp_secret_types' notes the supported types of secrets.
Bit 0 indicates secret type 1, bit 1 indicates type 2, and so on.
'max_secrets' notes the maximum amount of secrets the secret store can
store per pv guest.
Signed-off-by: Steffen Eiden <seiden@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20230615100533.3996107-8-seiden@linux.ibm.com
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Message-Id: <20230615100533.3996107-8-seiden@linux.ibm.com>
Userspace can call the Lock Secret Store Ultravisor Call
using IOCTLs on the uvdevice. The Lock Secret Store UV call
disables all additions of secrets for the future.
The uvdevice is merely transporting the request from userspace to the
Ultravisor.
Signed-off-by: Steffen Eiden <seiden@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20230615100533.3996107-6-seiden@linux.ibm.com
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Message-Id: <20230615100533.3996107-6-seiden@linux.ibm.com>
Userspace can call the List Secrets Ultravisor Call
using IOCTLs on the uvdevice. The List Secrets UV call lists the
identifier of the secrets in the UV secret store.
The uvdevice is merely transporting the request from userspace to
Ultravisor. It's neither checking nor manipulating the request or
response data.
Signed-off-by: Steffen Eiden <seiden@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20230615100533.3996107-5-seiden@linux.ibm.com
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Message-Id: <20230615100533.3996107-5-seiden@linux.ibm.com>
Userspace can call the Add Secret Ultravisor Call using IOCTLs on the
uvdevice. The Add Secret UV call sends an encrypted and
cryptographically verified request to the Ultravisor. The request
inserts a protected guest's secret into the Ultravisor for later use.
The uvdevice is merely transporting the request from userspace to the
Ultravisor. It's neither checking nor manipulating the request data.
Signed-off-by: Steffen Eiden <seiden@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20230615100533.3996107-4-seiden@linux.ibm.com
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Message-Id: <20230615100533.3996107-4-seiden@linux.ibm.com>
Add an IOCTL that allows userspace to find out which IOCTLs the uvdevice
supports without trial and error.
Explicitly expose the IOCTL nr for the request types.
Signed-off-by: Steffen Eiden <seiden@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20230615100533.3996107-3-seiden@linux.ibm.com
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Message-Id: <20230615100533.3996107-3-seiden@linux.ibm.com>
KVM needs the struct's values to be able to provide PV support.
The uvdevice is currently guest only and will need the struct's values
for call support checking and potential future expansions.
As uv.c is only compiled with CONFIG_PGSTE or
CONFIG_PROTECTED_VIRTUALIZATION_GUEST we don't need a second check in
the code. Users of uv_info will need to fence for these two config
options for the time being.
Signed-off-by: Steffen Eiden <seiden@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20230615100533.3996107-2-seiden@linux.ibm.com
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Message-Id: <20230615100533.3996107-2-seiden@linux.ibm.com>
We do check for target CPU == -1, but this might change at the time we
are going to use it. Hold the physical target CPU in a local variable to
avoid out-of-bound accesses to the cpu arrays.
Cc: Pierre Morel <pmorel@linux.ibm.com>
Fixes: 87e28a15c4 ("KVM: s390: diag9c (directed yield) forwarding")
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
bit_and() uses the count of bits as the woking length.
Fix the previous implementation and effectively use
the right bitmap size.
Fixes: 19fd83a647 ("KVM: s390: vsie: allow CRYCB FORMAT-1")
Fixes: 56019f9aca ("KVM: s390: vsie: Allow CRYCB FORMAT-2")
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/kvm/20230511094719.9691-1-pmorel@linux.ibm.com/
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Merge the feature branches scheduled for 6.5:
- replace the usage of weak PRNGs, by David Keisar Schmidt
- introduce the SLAB_NO_MERGE kmem_cache flag, by Jesper Dangaard Brouer
- deprecate CONFIG_SLAB, with a planned removal, by myself
Add a selftest for CMMA migration on s390.
The tests cover:
- interaction of dirty tracking and migration mode, see my recent patch
"KVM: s390: disable migration mode when dirty tracking is disabled" [1],
- several invalid calls of KVM_S390_GET_CMMA_BITS, for example: invalid
flags, CMMA support off, with/without peeking
- ensure KVM_S390_GET_CMMA_BITS initally reports all pages as dirty,
- ensure KVM_S390_GET_CMMA_BITS properly skips over holes in memslots, but
also non-dirty pages
Note that without the patch at [1] and the small fix in this series, the
selftests will fail.
[1] https://lore.kernel.org/all/20230127140532.230651-2-nrb@linux.ibm.com/
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20230324145424.293889-3-nrb@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
[frankja@linux.ibm.com: squashed
20230606150510.671301-1-nrb@linux.ibm.com / "KVM: s390: selftests:
CMMA: don't run if CMMA not supported"]
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
When CONFIG_MEMCG_KMEM is enabled, we disable cache merging for
KMALLOC_NORMAL caches so they don't end up merged with a cache that uses
ad-hoc __GFP_ACCOUNT when allocating. This was implemented by setting
the refcount to -1, but now we have a proper SLAB_NO_MERGE flag, so use
that instead.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: David Rientjes <rientjes@google.com>
Now that GPIO aggregator supports a delay line, drop the duplicative
functionality, i.e. the entire gpio-delay driver.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The aggregator mode can also handle properties of the platform,
that do not belong to the GPIO controller itself. One of such
a property is a signal delay line. Set up a parser to support it.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
In some cases the GPIO may require an additional delay after setting
its value. Add support for that into the GPIO forwarder code.
This will be fully enabled for use in the following changes.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
They stop the driver being used with ACPI PRP0001 and are something
I want to avoid being cut and paste into new drivers. Also include
mod_devicetable.h as we struct of_device_id is defined in there.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
e0bddc19ba ("x86/mm: Reduce untagged_addr() overhead for systems without LAM")
removed its only usage site so drop it.
Move the tlbstate_untag_mask up in the header and drop the ugly
ifdeffery as the unused declaration should be properly discarded.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/r/20230614174148.5439-1-bp@alien8.de
With offloading enabled, esp_xmit() gets invoked very late, from within
validate_xmit_xfrm() which is after validate_xmit_skb() validates and
linearizes the skb if the underlying device does not support fragments.
esp_output_tail() may add a fragment to the skb while adding the auth
tag/ IV. Devices without the proper support will then send skb->data
points to with the correct length so the packet will have garbage at the
end. A pcap sniffer will claim that the proper data has been sent since
it parses the skb properly.
It is not affected with INET_ESP_OFFLOAD disabled.
Linearize the skb after offloading if the sending hardware requires it.
It was tested on v4, v6 has been adopted.
Fixes: 7785bba299 ("esp: Add a software GRO codepath")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Initializing the FPU during the early boot process is a pointless
exercise. Early boot is convoluted and fragile enough.
Nothing requires that the FPU is set up early. It has to be initialized
before fork_init() because the task_struct size depends on the FPU register
buffer size.
Move the initialization to arch_cpu_finalize_init() which is the perfect
place to do so.
No functional change.
This allows to remove quite some of the custom early command line parsing,
but that's subject to the next installment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230613224545.902376621@linutronix.de
No point in doing this during really early boot. Move it to an early
initcall so that it is set up before possible user mode helpers are started
during device initialization.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230613224545.727330699@linutronix.de
Invoke the X86ism mem_encrypt_init() from X86 arch_cpu_finalize_init() and
remove the weak fallback from the core code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230613224545.670360645@linutronix.de
X86 is reworking the boot process so that initializations which are not
required during early boot can be moved into the late boot process and out
of the fragile and restricted initial boot phase.
arch_cpu_finalize_init() is the obvious place to do such initializations,
but arch_cpu_finalize_init() is invoked too late in start_kernel() e.g. for
initializing the FPU completely. fork_init() requires that the FPU is
initialized as the size of task_struct on X86 depends on the size of the
required FPU register buffer.
Fortunately none of the init calls between calibrate_delay() and
arch_cpu_finalize_init() is relevant for the functionality of
arch_cpu_finalize_init().
Invoke it right after calibrate_delay() where everything which is relevant
for arch_cpu_finalize_init() has been set up already.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Link: https://lore.kernel.org/r/20230613224545.612182854@linutronix.de
Everything is converted over to arch_cpu_finalize_init(). Remove the
check_bugs() leftovers including the empty stubs in asm-generic, alpha,
parisc, powerpc and xtensa.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Link: https://lore.kernel.org/r/20230613224545.553215951@linutronix.de
check_bugs() is about to be phased out. Switch over to the new
arch_cpu_finalize_init() implementation.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20230613224545.493148694@linutronix.de
check_bugs() is about to be phased out. Switch over to the new
arch_cpu_finalize_init() implementation.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/20230613224545.431995857@linutronix.de
check_bugs() is about to be phased out. Switch over to the new
arch_cpu_finalize_init() implementation.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230613224545.254342916@linutronix.de
check_bugs() is a dumping ground for finalizing the CPU bringup. Only parts of
it has to do with actual CPU bugs.
Split it apart into arch_cpu_finalize_init() and cpu_select_mitigations().
Fixup the bogus 32bit comments while at it.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230613224545.019583869@linutronix.de
check_bugs() has become a dumping ground for all sorts of activities to
finalize the CPU initialization before running the rest of the init code.
Most are empty, a few do actual bug checks, some do alternative patching
and some cobble a CPU advertisement string together....
Aside of that the current implementation requires duplicated function
declaration and mostly empty header files for them.
Provide a new function arch_cpu_finalize_init(). Provide a generic
declaration if CONFIG_ARCH_HAS_CPU_FINALIZE_INIT is selected and a stub
inline otherwise.
This requires a temporary #ifdef in start_kernel() which will be removed
along with check_bugs() once the architectures are converted over.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230613224544.957805717@linutronix.de
Functions efx_tc_netdev_event and efx_tc_netevent_event do not exist
in that case as object files tc_bindings.o and tc_encap_actions.o
are not built, so the calls to them from ef100_netdev_event and
ef100_netevent_event cause link errors.
Wrap the corresponding header files (tc_bindings.h, tc_encap_actions.h)
with #if IS_ENABLED(CONFIG_SFC_SRIOV), and add an #else with static
inline stubs for these two functions.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306102026.ISK5JfUQ-lkp@intel.com/
Fixes: 7e5e7d8000 ("sfc: neighbour lookup for TC encap action offload")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_ETHERNET=m or CONFIG_FDDI=m, lcs.s has build errors or
warnings:
../drivers/s390/net/lcs.c:40:2: error: #error Cannot compile lcs.c without some net devices switched on.
40 | #error Cannot compile lcs.c without some net devices switched on.
../drivers/s390/net/lcs.c: In function 'lcs_startlan_auto':
../drivers/s390/net/lcs.c:1601:13: warning: unused variable 'rc' [-Wunused-variable]
1601 | int rc;
Solve this by using IS_ENABLED(CONFIG_symbol) instead of ifdef
CONFIG_symbol. The latter only works for builtin (=y) values
while IS_ENABLED() works for builtin or modular values.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Alexandra Winter <wintera@linux.ibm.com>
Cc: Wenjia Zhang <wenjia@linux.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple more fixes for v6.4, one fixing a misleading error log and
another stopping us seeing spurious failures setting the master volume
on some Tegra systems introduced by a change to how we calculate delay
times.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmSK+S0ACgkQJNaLcl1U
h9BoSAf/ddQv2NM7kH1N7Iu1bEWGZMBi9RyfxHoJPfg4lkG4x26NWCoU6r5N5ymR
0nZRnQs9cDsNoGSr9UDQK4DV6Wv4I4oyeg1O2H+4wGIic9t/XLJIKfVJKrox7jzW
cX7gbB6EytGF04ggBmazfNU8CGO2xEAL0gA9ycwceLzIq6ODXapXBVPOuxVjHuns
FKCSzDEh2HzuWAmn4FFGH7vGlQbJm9VPAsMXLFNA+Xpr2JKpjfmY/aSR0seKnjHz
Zp81Z8buZeFmANbVvZ0WuXfNUltwDjgdwulLDb6cq8Drv2qzUr0VH858Q5duwFIr
y2kTbOpZRD2mXLaVyTzUF9yRnKUVEw==
=HPCX
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.4-rc6-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.4
A couple more fixes for v6.4, one fixing a misleading error log and
another stopping us seeing spurious failures setting the master volume
on some Tegra systems introduced by a change to how we calculate delay
times.
This commit adds new DEVICE_FLG with QUIRK_FLAG_DSD_RAW and Vendor Id for
HEM devices which supports native DSD. Prior to this change Linux kernel
was not enabling native DSD playback for HEM devices, and as a result,
DSD audio was being converted to PCM "on the fly". HEM devices,
when connected to the system, would only play audio in PCM format,
even if the source material was in DSD format. With the addition of new
VENDOR_FLG in the quircks.c file, the devices are now correctly
recognized, and raw DSD data is transmitted to the device,
allowing for native DSD playback.
Signed-off-by: Lukasz Tyl <ltyl@hem-e.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230614122524.30271-1-ltyl@hem-e.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As reported in the bugzilla below, the PM resume of a UAC3 device may
fail due to the incomplete power state change, stuck at D1. The
reason is that the driver expects the full D0 power state change only
at hw_params, while the normal PCM resume procedure doesn't call
hw_params.
For fixing the bug, we add the same power state update to D0 at the
prepare callback, which is certainly called by the resume procedure.
Note that, with this change, the power state change in the hw_params
becomes almost redundant, since snd_usb_hw_params() doesn't touch the
parameters (at least it tires so). But dropping it is still a bit
risky (e.g. we have the media-driver binding), so I leave the D0 power
state change in snd_usb_hw_params() as is for now.
Fixes: a0a4959eb4 ("ALSA: usb-audio: Operate UAC3 Power Domains in PCM callbacks")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217539
Link: https://lore.kernel.org/r/20230612132818.29486-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel Barlow Ridge Thunderbolt controller has 3 DP IN adapters. This
allows 3 simultaneus DisplayPort tunnels through either one or two USB4
downstream ports (in any possible configuration). Add test case for
this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds support for the UHBR (Ultra High Bit Rate) bandwidths
introduced with DisplayPort 2.0 (and refined in 2.1). These can go up to
80 Gbit/s and their support is represent in additional bits in the DP IN
capability.
This updates the DisplayPort tunneling to support these new rates too.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make sure the DisplayPort bandwidth allocation mode function names are
consistent with the existing ones, such as USB3.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
