Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 18f8e6f695 ("power: supply: bq24190_charger: Get input_current_limit from our supplier")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq25892 model relies on external charger-type detection and once
that is done the bq25890_charger code will update the input current
and if pumpexpress is used also the input voltage.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current or voltage. This allows the fuel-gauge driver
to timely recheck if the battery is charging after the new input
settings have been applied and then it can immediately notify
userspace about this.
Fixes: 48f45b094d ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol")
Fixes: eab25b4f93 ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use mod_delayed_work() instead of separate cancel_delayed_work_sync() +
schedule_delayed_work() calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Move the bq27xxx_battery_update() functions to below
the bq27xxx_battery_current_and_status() function.
This is just moving a block of text, no functional changes.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a cache parameter to bq27xxx_battery_current_and_status() so that
it can optionally use cached flags instead of re-reading them itself.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa8118 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b ("power: bq27xxx_battery: Add interrupt handling support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
bq27xxx_battery_update() assumes / requires that it is only run once,
not multiple times at the same time. But there are 3 possible callers:
1. bq27xxx_battery_poll() delayed_work item handler
2. bq27xxx_battery_irq_handler_thread() I2C IRQ handler
3. bq27xxx_battery_setup()
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Move the existing I/O read and write code for I/O memory into
the new helpers fb_cfb_read() and fb_cfb_write(). Make them the
default fp_ops. No functional changes.
In the near term, the new functions will be useful to the DRM
subsystem, which currently provides it's own implementation. It
can then use the shared code. In the longer term, it might make
sense to revise the I/O helper's default status and make them
opt-in by the driver. Systems that don't use them would not
contain the code any longer.
v2:
* add detailed commit message (Javier)
* rename fb_cfb_() to fb_io_() (Geert)
* add fixes that got lost while moving the code (Geert)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-19-tzimmermann@suse.de
Push the test for info->screen_base from fb_read() and fb_write() into
the implementations of struct fb_ops.{fb_read,fb_write}. In cases where
the driver operates on info->screen_buffer, test this field instead.
While bothi fields, screen_base and screen_buffer, are stored in the
same location, they refer to different address spaces. For correctness,
we want to test each field in exactly the code that uses it.
v2:
* also test screen_base in pvr2fb (Geert)
* also test screen_buffer in ivtvfb, arcfb, broadsheetfb,
hecubafb, metronomefb and ssd1307fb (Geert)
* give a rational for the change (Geert)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-18-tzimmermann@suse.de
The file-op entry points fb_read() and fb_write() verify that
info->state has been set to FBINFO_STATE_RUNNING. Remove the same
test from the implementations of struct fb_ops.{fb_read,fb_write}.
v2:
* also remove test from ivtvfb, braodsheetfb, hecubafb and
metronomefb (Geert)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-17-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
Since the fb_sys_{read,write}() functions operate on the latter address
space, it is wrong to use .screen_base and .screen_buffer must be used
instead. This also gets rid of all the casting needed due to not using
the correct data type.
v2:
* add detailed commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-16-tzimmermann@suse.de
Always return the number of bytes read or written within the
framebuffer. Only return an errno code if framebuffer memory
was not touched. This is the semantics required by POSIX and
makes fb_read() and fb_write() compatible with IGT tests. [1]
This bug has been fixed for fb_write() long ago by
commit 6a2a88668e ("[PATCH] fbdev: Fix return error of
fb_write"). The code in fb_read() and the corresponding fb_sys_()
helpers was forgotten.
It can happen that copy_{from, to}_user() only partially copies
the given buffer. Take this into account when calculating the
number of bytes.
v2:
* consider return value from copy_{from,to}_user() (Geert)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://gitlab.freedesktop.org/drm/igt-gpu-tools/-/blob/master/tests/fbdev.c # 1
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-15-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-14-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-13-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-12-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-11-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-10-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-9-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-8-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-7-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-6-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-5-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-4-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-3-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-2-tzimmermann@suse.de
Merge series from Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>:
There are large number of QSPI irqs that fire during boot/init and later
on every suspend/resume.
This could be made faster by doing DMA instead of PIO.
Below is comparison for number of interrupts raised in 2 scenarios...
Boot up and stabilise
Suspend/Resume
Sequence PIO DMA
=======================
Boot-up 69088 19284
S/R 5066 3430
Speed test results...
spi-nor read times in sec after 2 min uptime
============================================
PIO - Iterations-1000, min=3.18, max=3.74, avg=3.53
DMA - Iterations-1000, min=1.21, max=2.28, avg=1.79
spi-nor write times in sec after 2 min uptime
=============================================
PIO - Iterations-1000, min=3.20, max=8.24, avg=3.58
DMA - Iterations-1000, min=1.25, max=5.13, avg=1.82
Further testing performed...
a) multiple entries in sgt (simulated by max_dma_len = 1024)
b) fallback to pio (simulated by dma setup failure)
Normally __swp_entry_to_pte() is never called with a value translating
to a valid PTE. The only known exception is pte_swap_tests(), resulting
in a WARN splat in Xen PV guests, as __pte_to_swp_entry() did
translate the PFN of the valid PTE to a guest local PFN, while
__swp_entry_to_pte() doesn't do the opposite translation.
Fix that by using __pte() in __swp_entry_to_pte() instead of open
coding the native variant of it.
For correctness do the similar conversion for __swp_entry_to_pmd().
Fixes: 05289402d7 ("mm/debug_vm_pgtable: add tests validating arch helpers for core MM features")
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230306123259.12461-1-jgross@suse.com
Merge series from Jaewon Kim <jaewon02.kim@samsung.com>:
Previously, polling mode was supported as quirk for SOC without DMA.
In order to use it more flexibly, it is supported when there is
no dmas property in devicetree, and the issue of using excessive CPU
usage in polling mode is solved by adding sleep during transfer time and
supporting interrupt mode.
Changes in V3.
- Fix patch commit message.
- Change of_find_property() to of_property_present() with code cleanup
- Remove cpu_relax() related patch.
- Changes use_irq variable type to bool
Changes in V2.
- Switched to polling mode if there is no dmas property in devicetree.
- Add cpu_releax() in polling loop
- Add lower limit in IRQ mode
Jaewon Kim (3):
spi: s3c64xx: change polling mode to optional
spi: s3c64xx: add sleep during transfer
spi: s3c64xx: support interrupt based pio mode
drivers/spi/spi-s3c64xx.c | 81 +++++++++++++++++++----
include/linux/platform_data/spi-s3c64xx.h | 1 +
2 files changed, 70 insertions(+), 12 deletions(-)
--
2.17.1
Introduce SNDRV_PCM_INFO_PERFECT_DRAIN and SNDRV_PCM_HW_PARAMS_NO_DRAIN_SILENCE
flags to fully control the filling of the silence samples in the drain ioctl.
Actually, the configurable silencing is going to be implemented in the user
space [1], but drivers (hardware) may not require this operation. Those flags
do the bidirectional setup for this operation:
1) driver may notify the presence of the perfect drain
2) user space may not require the filling of the silence samples to inhibit clicks
If we decide to move this operation to the kernel space in future, the
SNDRV_PCM_INFO_PERFECT_DRAIN flag may handle this situation without
double "silence" processing (user + kernel space).
The ALSA API should be universal, so forcing the behaviour (modifying of
the ring buffer with any samples) for the drain operation is not ideal.
[1] https://lore.kernel.org/alsa-devel/20230502115010.986325-1-perex@perex.cz/
[ fixed a typo in comment by tiwai ]
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230502115536.986900-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c5 ("power_supply: Add new LED trigger charging-blink-solid-full")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
twl4030_madc_bat_ext_changed() is a wrapper around
"power_supply_changed(psy);" and it has the same prototype.
Remove it, replacing it with making the external_power_changed
callback directly point to power_supply_changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
max17042_external_power_changed() is a wrapper around
"power_supply_changed(psy);" and it has the same prototype.
Remove it, replacing it with making the external_power_changed
callback directly point to power_supply_changed.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Purism Kernel Team <kernel@puri.sm>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
sc27xx_fgu_external_power_changed() dereferences data->battery,
which gets sets in ab8500_btemp_probe() like this:
data->battery = devm_power_supply_register(dev, &sc27xx_fgu_desc,
&fgu_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where sc27xx_fgu_external_power_changed() may get called while
data->battery has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in data->battery,
so sc27xx_fgu_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
After this change sc27xx_fgu_external_power_changed() is reduced to just
"power_supply_changed(psy);" and it has the same prototype. While at it
simply replace it with making the external_power_changed callback
directly point to power_supply_changed.
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
bq25890_charger_external_power_changed() dereferences bq->charger,
which gets sets in bq25890_power_supply_init() like this:
bq->charger = devm_power_supply_register(bq->dev, &bq->desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where bq25890_charger_external_power_changed() may get called while
bq->charger has not been set yet leading to a NULL pointer dereference.
This race hits during boot sometimes on a Lenovo Yoga Book 1 yb1-x90f
when the cht_wcove_pwrsrc (extcon) power_supply is done with detecting
the connected charger-type which happens to exactly hit the small window:
BUG: kernel NULL pointer dereference, address: 0000000000000018
<snip>
RIP: 0010:__power_supply_is_supplied_by+0xb/0xb0
<snip>
Call Trace:
<TASK>
__power_supply_get_supplier_property+0x19/0x50
class_for_each_device+0xb1/0xe0
power_supply_get_property_from_supplier+0x2e/0x50
bq25890_charger_external_power_changed+0x38/0x1b0 [bq25890_charger]
__power_supply_changed_work+0x30/0x40
class_for_each_device+0xb1/0xe0
power_supply_changed_work+0x5f/0xe0
<snip>
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in bq->charger,
so bq25890_charger_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: eab25b4f93 ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection")
Cc: stable@vger.kernel.org
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
fuel_gauge_external_power_changed() dereferences info->bat,
which gets sets in axp288_fuel_gauge_probe() like this:
info->bat = devm_power_supply_register(dev, &fuel_gauge_desc, &psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where fuel_gauge_external_power_changed() may get called while
info->bat has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in info->bat,
so fuel_gauge_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: 30abb3d079 ("power: supply: axp288_fuel_gauge: Take lock before updating the valid flag")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
ab8500_btemp_external_power_changed() dereferences di->btemp_psy,
which gets sets in ab8500_btemp_probe() like this:
di->btemp_psy = devm_power_supply_register(dev, &ab8500_btemp_desc,
&psy_cfg);
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where ab8500_btemp_external_power_changed() may get called while
di->btemp_psy has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in di->btemp_psy,
so ab8500_btemp_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
And the same applies to ab8500_fg_external_power_changed().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Neither FSL_SOC_BOOKE nor PPC_86xx enables CONFIG_PCI by
default, so it may be unset in some randconfigs.
When that happens, FSL_ULI1575 may be set when it should not be
since it is a PCI driver. When it is set, there are 3 kconfig
warnings and a slew of build errors
WARNING: unmet direct dependencies detected for PCI_QUIRKS
Depends on [n]: PCI [=n]
Selected by [y]:
- FSL_PCI [=y]
WARNING: unmet direct dependencies detected for GENERIC_ISA_DMA
Depends on [n]: ISA_DMA_API [=n]
Selected by [y]:
- FSL_ULI1575 [=y] && (FSL_SOC_BOOKE [=n] || PPC_86xx [=y])
WARNING: unmet direct dependencies detected for PPC_INDIRECT_PCI
Depends on [n]: PCI [=n]
Selected by [y]:
- FSL_PCI [=y]
and 30+ build errors.
Fixes: 22fdf79171 ("powerpc/fsl_uli1575: Allow to disable FSL_ULI1575 support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230429043519.19807-1-rdunlap@infradead.org
Currently, vkms supports the rotate-90, rotate-180, reflect-x and
reflect-y properties. Therefore, improve the vkms IGT test coverage by
adding the rotate-270 property to vkms. The rotation was implement by
software: rotate the way the blending occurs by making the source x axis
be the destination y axis and the source y axis be the destination x
axis and reverse-read the axis.
Now, vkms supports all possible rotation values.
Tested with igt@kms_rotation_crc@primary-rotation-270 [1],
and igt@kms_rotation_crc@sprite-rotation-270 [1].
[1] https://patchwork.freedesktop.org/series/116025/
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230418130525.128733-6-mcanal@igalia.com
Commit e4ab08be5b ("powerpc/isa-bridge: Remove open coded "ranges"
parsing") broke PASemi Nemo board booting. The issue is the ISA I/O
range was not getting mapped as the logic to handle no "ranges" was
inverted. If phb_io_base_phys is non-zero, then the ISA range defaults
to the first 64K of the PCI I/O space. phb_io_base_phys should only be 0
when looking for a non-PCI ISA region.
Fixes: e4ab08be5b ("powerpc/isa-bridge: Remove open coded "ranges" parsing")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Link: https://lore.kernel.org/all/301595ad-0edf-2113-b55f-f5b8051ed24c@xenosoft.de/
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230505171816.3175865-1-robh@kernel.org
Currently, vkms only supports the rotate-180, reflect-x and reflect-y
properties. Therefore, improve the vkms IGT test coverage by adding the
rotate-90 property to vkms. The rotation was implement by software: rotate
the way the blending occurs by making the source x axis be the destination
y axis and the source y axis be the destination x axis.
Tested with igt@kms_rotation_crc@primary-rotation-90 [1],
igt@kms_rotation_crc@sprite-rotation-90 [1], and
igt@kms_rotation_crc@sprite-rotation-90-pos-100-0 [1].
[1] https://patchwork.freedesktop.org/series/116025/
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230418130525.128733-5-mcanal@igalia.com
Currently, vkms only supports the reflect-x property. Therefore, add the
reflect-y property to vkms through a software implementation of the
operation. This is possible by reverse reading the y axis during the
blending.
Note that, by implementing the reflect-x and reflect-y properties, it is
also possible to add the rotate-180 property, as it is a combination
of those two properties.
Tested with igt@kms_rotation_crc@primary-reflect-y [1],
igt@kms_rotation_crc@sprite-reflect-y [1],
igt@kms_rotation_crc@primary-rotation-180,
igt@kms_rotation_crc@sprite-rotation-180,
and igt@kms_rotation_crc@cursor-rotation-180.
[1] https://patchwork.freedesktop.org/series/116025/
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230418130525.128733-4-mcanal@igalia.com
Currently, vkms doesn't support any reflection property. Therefore, add
the reflect-x property to vkms through a software implementation of the
operation. This is possible by reverse reading the x axis during the
blending.
Tested with igt@kms_rotation_crc@primary-reflect-x [1] and
igt@kms_rotation_crc@sprite-reflect-x [1].
[1] https://patchwork.freedesktop.org/series/116025/
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230418130525.128733-3-mcanal@igalia.com
dev_err_probe() already display the error code. There is no need to
duplicate it explicitly in the error message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Returning an error code from a remove callback makes the driver core
emit a generic (and so little helpful) error message and after that the
error code is ignored and the device unbound.
As gpio_restart_remove() already emits an error message, suppressing the
generic error is no loss.
Then convert to .remove_new() which is equivalent to returning 0
unconditionally in .remove(). See commit 5c5a7680e6 ("platform:
Provide a remove callback that returns no value") for its rational.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
