The colon ("bit combination 03/10") is a valid character in parameter
substrings. ECMA-48 says:
Each parameter sub-string consists of one or more bit combinations
from 03/00 to 03/10; the bit combinations from 03/00 to 03/09
represent the digits ZERO to NINE; bit combination 03/10 may be used
as a separator in a parameter sub-string, for example, to separate
the fractional part of a decimal number from the integer part of
that number.
To my knowledge, the only codes where 03/10 is actually used as a
separator are the CSI-m SGR sequences. The colon separated format is
superior as an embedded string for software that doesn't wish to link
ncurses terminal database, because terminals that do not support the
requested SGR sequence can safely skip the sub-parameters rather than
misinterpret them as another sequence. Hence, some software have started
using this "modern" format [1]. We should support the colon separated
format as well.
[1] 6eabe9f2ff
Signed-off-by: Ronan Pigott <ronan@rjp.ie>
Link: https://patch.msgid.link/20260303010701.631022-1-ronan@rjp.ie
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace enables flow control (CRTSCTS), the driver
deasserts RTS even when the receive buffer has space. This prevents the
peer device from transmitting, causing communication to stall.
The root cause is that the driver unconditionally uses manual RTS control
regardless of flow control mode. When CRTSCTS is set, the hardware should
automatically manage RTS based on buffer status, but the driver overrides
this by setting manual control.
Fix this by introducing port->manual_flow flag. In set_termios(), disable
manual flow when CRTSCTS is set. In set_mctrl(), only assert
SE_UART_MANUAL_RFR when manual_flow is active. Verified by enabling and
disabling hardware flow control with stty.
Signed-off-by: Anup Kulkarni <anup.kulkarni@oss.qualcomm.com>
Link: https://patch.msgid.link/20260310104155.339010-1-anup.kulkarni@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since sdma hardware configure postpone to transfer phase, have to
disable dma request before dma transfer setup because there is a
hardware limitation on sdma event enable(ENBLn) as below.
Refer SDMA 2.6.28 Channel Enable RAM (SDMAARMx_CHNENBLn) section:
"It is thus essential for the Arm platform to program them before any
DMA request is triggered to the SDMA, otherwise an unpredictable
combination of channels may be started."
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://patch.msgid.link/20260312094526.297348-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the SystemBase Multi I/O serial cards, which are
"compatible" with a standard 16550A controllers, except that they need
to have their interrupts enabled in a proprietary way.
Tested with a Delock "Serial PCI Express x1 Card 8x Serial RS-232".
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20260225081739.946723-1-mwalle@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver currently only supports builds against a PIC32 target, or
with COMPILE_TEST on MIPS. Now that commit 24cad1a228 ("serial:
pic32_uart: update include to use pic32.h from platform_data") is
merged, it's possible to compile this driver on other architectures.
To avoid future breakage of this driver in the future, let's update the
Kconfig so that it can be built with COMPILE_TEST enabled on all
architectures.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://patch.msgid.link/20260222-serial-pic32-v1-1-8fdbc0d0d334@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver runs also on SoCs without a Tegra20 APB DMA controller (e.g.
Tegra234).
Remove the Kconfig dependency on TEGRA20_APB_DMA, and remove reference to
the APB DMA controller from the Kconfig help text.
Signed-off-by: Francesco Lavra <flavra@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260303111438.2691799-1-flavra@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amlogic A9 SoCs uses the same UART controller as S4 SoCs.
There is no need for an extra compatible line in the driver,
but add A9 compatible line for documentation.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://patch.msgid.link/20260303-serial-binding-v1-1-c3df2a8f6fa3@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a check for clk_enable() in auart_console_write(). If
clk_enable() fails, return immediately to avoid accessing
hardware registers while the clock is not enabled.
Signed-off-by: Zhaoyang Yu <2426767509@qq.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/tencent_AB29FADF1FAD67D818283B6BB4FDF66F2F08@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a key is pressed with modifiers (Shift, Ctrl, Alt, etc.) and the
modifier-specific keymap has no binding (K_HOLE) or doesn't exist, fall
back to the plain keymap if the plain entry is a modifier-aware type
(KT_CUR or KT_CSI).
This allows arrow keys and CSI navigation keys to automatically handle
all modifier combinations with just a single plain map entry. The key
handlers (k_cur and k_csi) read the modifier state at runtime and encode
it into the output sequence.
For example, with just:
keycode 103 = Up
keycode 104 = Csi_Home
All these combinations now work automatically:
Up -> ESC [ A
Shift+Up -> ESC [ 1 ; 2 A
Ctrl+Up -> ESC [ 1 ; 5 A
Home -> ESC [ 1 ~
Shift+Home -> ESC [ 1 ; 2 ~
Ctrl+Home -> ESC [ 1 ; 5 ~
Previously, each modifier combination required an explicit keymap entry,
which was tedious and consumed keymap slots.
Explicit modifier bindings still take precedence - the fallback only
triggers when the modifier-specific entry is empty.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://patch.msgid.link/20260203045457.1049793-4-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new keysym type KT_CSI that generates CSI tilde sequences with
automatic modifier encoding. The keysym value encodes the CSI parameter
number, producing sequences like ESC [ <value> ~ or ESC [ <value> ; <mod> ~
when Shift, Alt, or Ctrl modifiers are held.
This allows navigation keys (Home, End, Insert, Delete, PgUp, PgDn) and
function keys to generate modifier-aware escape sequences without
consuming string table entries for each modifier combination.
Define key symbols for navigation keys (K_CSI_HOME, K_CSI_END, etc.)
and function keys (K_CSI_F1 through K_CSI_F20) using standard xterm
CSI parameter values.
The modifier encoding follows the xterm convention:
mod = 1 + (shift ? 1 : 0) + (alt ? 2 : 0) + (ctrl ? 4 : 0)
Allowed CSI parameter values range from 0 to 99.
Note: The Linux console historically uses a non-standard double-bracket
format for F1-F5 (ESC [ [ A through ESC [ [ E) rather than the xterm
tilde format (ESC [ 11 ~ through ESC [ 15 ~). The K_CSI_F1 through
K_CSI_F5 definitions use the xterm format. Converting F1-F5 to KT_CSI
would require updating the "linux" terminfo entry to match. Navigation
keys and F6-F20 already use the tilde format and are fully compatible.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://patch.msgid.link/20260203045457.1049793-3-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generate xterm-style CSI sequences with modifier parameters for arrow
keys when Shift, Alt, or Ctrl are held. For example, Shift+Up produces
ESC [ 1 ; 2 A instead of plain ESC [ A.
The modifier encoding follows the standard xterm convention:
mod = 1 + (shift ? 1 : 0) + (alt ? 2 : 0) + (ctrl ? 4 : 0)
When no modifiers are pressed, the original behavior is preserved.
Explicit keymap bindings for modified cursor keys (e.g., "shift keycode
103 = Find") take precedence over this automatic modifier encoding.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://patch.msgid.link/20260203045457.1049793-2-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct kernel-doc comment format and add a missing to avoid
kernel-doc warnings:
Warning: include/linux/serdev.h:49 struct member 'write_comp' not
described in 'serdev_device'
Warning: include/linux/serdev.h:49 struct member 'write_lock' not
described in 'serdev_device'
Warning: include/linux/serdev.h:68 struct member 'shutdown' not described
in 'serdev_device_driver'
Warning: include/linux/serdev.h:134 function parameter 'serdev' not
described in 'serdev_device_put'
Warning: include/linux/serdev.h:162 function parameter 'ctrl' not
described in 'serdev_controller_put'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260311052347.305612-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers were added about 3 years ago, and depend on the
XTENSA_PLATFORM_ESP32 config option which has never existed,
so no device can actually use them.
They can only be compiled with COMPILE_TEST.
In a previous conversation [1], Greg suggested removing the
drivers, and Max, the original submitter of the drivers, agreed
due to a lack of foreseeable development.
Link: https://lore.kernel.org/all/20260308131412.1102749-1-julianbraha@gmail.com/ [1]
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Link: https://patch.msgid.link/20260309122321.1528622-1-julianbraha@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DMA controllers require transfer lengths to be aligned to a
specific boundary. For example, the Tegra GPC DMA requires 4-byte
(word) aligned transfers and will reject unaligned lengths.
Align the TX DMA buffer length down to the DMA controller's copy_align
boundary before submitting the transfer. Any remaining unaligned bytes
will be transmitted via PIO on subsequent calls, which is the existing
fallback behavior when DMA is not used.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-5-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the NVIDIA Tegra264 UART controller, which is derived
from the AMBA PL011 design.
On Tegra264, the fractional baud rate divisor (FBRD) register is broken.
Using IBRD alone may not achieve the required baud rate
tolerance. Enable the skip_ibrd_fbrd and set_uartclk_rate flags for
the NVIDIA variant.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-4-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NVIDIA Tegra264 UART relies on configuring the UART clock rate
directly to program the desired baud rate.
Introduce the set_uartclk_rate vendor flag. When set, the driver
uses clk_set_rate() to program the UART clock to the desired baud
rate and clk_round_rate() to determine the maximum supported baud
rate.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-3-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NVIDIA Tegra264 UART has a broken fractional baud rate
divisor register. Using IBRD and FBRD may cause the baud rate
to fall outside the required tolerance.
Introduce the skip_ibrd_fbrd vendor flag to skip IBRD/FBRD
programming. When set, the baud rate is derived directly from the
UART clock rate using a fixed divisor.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Link: https://patch.msgid.link/20260225065915.341522-2-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the PL011 driver only enables the UART (by setting UARTEN
in REG_CR) in pl011_startup(), so if it is used for earlycon it is
relying on the bootrom/firmware having left the UART enabled.
There's no particular reason not to actively enable the UART before
using it for earlycon, and the earlycon handling for e.g. the 8250
UART sets up the UART in its setup function, so follow that in the
PL011.
This allows use of earlycon with a UART that the firmware hasn't
already been using for its own output, but the main motivation is
that QEMU will otherwise log a message complaining that the guest is
trying to write to a UART it never enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260210125100.223138-1-peter.maydell@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MAX_HVC_IUCV_LINES == HVC_ALLOC_TTY_ADAPTERS == 8.
This is the number of entries in:
static struct hvc_iucv_private *hvc_iucv_table[MAX_HVC_IUCV_LINES];
Sometimes hvc_iucv_table[] is limited by:
(a) if (num > hvc_iucv_devices) // for error detection
or
(b) for (i = 0; i < hvc_iucv_devices; i++) // in 2 places
(so these 2 don't agree; second one appears to be correct to me.)
hvc_iucv_devices can be 0..8. This is a counter.
(c) if (hvc_iucv_devices > MAX_HVC_IUCV_LINES)
If hvc_iucv_devices == 8, (a) allows the code to access hvc_iucv_table[8].
Oops.
Fixes: 44a01d5ba8 ("[S390] s390/hvc_console: z/VM IUCV hypervisor console support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260130072939.1535869-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_release_dma() is NULL-aware, no need to check this in the caller.
While at it, make sure DMA won't be used again, by NULLifying the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260128142726.128175-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a05025d0ce ("tty: serial: samsung_tty: use standard
debugging macros") changed the debug prints to dev_dbg, which can
result in deadlocks:
s3c24xx_serial_set_termios can be called with the port lock, and then
calls dev_dbg, which needs the console mutex. At the same time,
s3c24xx_serial_console_write can be called with the console lock
(e.g., inside console_unlock), and needs the port lock.
To avoid this, move one dev_dbg call and just delete the other.
Signed-off-by: Alyssa Milburn <amilburn@zall.org>
Link: https://patch.msgid.link/aXny9km6N1v9eoXU@zall.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix for the x86 EFI workaround keeping boot services code and data
regions reserved until after SetVirtualAddressMap() completes: deferred
struct page initialization may result in some of this memory to be lost
permanently.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQQm/3uucuRGn1Dmh0wbglWLn0tXAUCaaxHtgAKCRAwbglWLn0t
XIbNAPwNjw/TSgVD+Ur//yqY7TxZSBari8aheEkXNaYHFCPImwD6A1CzNGn6rcka
JzeP+6HeOO9c0xCBudcR0aRfSma3cQI=
=a+XF
-----END PGP SIGNATURE-----
Merge tag 'efi-fixes-for-v7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fix from Ard Biesheuvel:
"Fix for the x86 EFI workaround keeping boot services code and data
regions reserved until after SetVirtualAddressMap() completes:
deferred struct page initialization may result in some of this memory
being lost permanently"
* tag 'efi-fixes-for-v7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
x86/efi: defer freeing of boot services memory
A revert for the i801 driver restoring old locking behaviour.
-----BEGIN PGP SIGNATURE-----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=Nc8b
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"A revert for the i801 driver restoring old locking behaviour"
* tag 'i2c-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Revert "i2c: i801: replace acpi_lock with I2C bus lock"
- Fix SEV guest boot failures in certain circumstances, due
to very early code relying on a BSS-zeroed variable that
isn't actually zeroed yet an may contain non-zero bootup
values. Move the variable into the .data section go gain
even earlier zeroing.
- Expose & allow the IBPB-on-Entry feature on SNP guests,
which was not properly exposed to guests due to initial
implementational caution.
- Fix O= build failure when CONFIG_EFI_SBAT_FILE is using
relative file paths.
- 4 commits to fix the various SNC (Sub-NUMA Clustering)
topology enumeration bugs/artifacts (sched-domain build
errors mostly). SNC enumeration data got more complicated
with Granite Rapids X (GNR) and Clearwater Forest X (CWF),
which exposed these bugs and made their effects more
serious.
- Also use the now sane(r) SNC code to fix resctrl SNC
detection bugs.
- Work around a historic libgcc unwinder bug in the vdso32
sigreturn code (again), which regressed during an overly
aggressive recent cleanup of DWARF annotations.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KlDX
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Fix SEV guest boot failures in certain circumstances, due to
very early code relying on a BSS-zeroed variable that isn't
actually zeroed yet an may contain non-zero bootup values
Move the variable into the .data section go gain even earlier
zeroing
- Expose & allow the IBPB-on-Entry feature on SNP guests, which
was not properly exposed to guests due to initial implementational
caution
- Fix O= build failure when CONFIG_EFI_SBAT_FILE is using relative
file paths
- Fix the various SNC (Sub-NUMA Clustering) topology enumeration
bugs/artifacts (sched-domain build errors mostly).
SNC enumeration data got more complicated with Granite Rapids X
(GNR) and Clearwater Forest X (CWF), which exposed these bugs
and made their effects more serious
- Also use the now sane(r) SNC code to fix resctrl SNC detection bugs
- Work around a historic libgcc unwinder bug in the vdso32 sigreturn
code (again), which regressed during an overly aggressive recent
cleanup of DWARF annotations
* tag 'x86-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/vdso32: Work around libgcc unwinder bug
x86/resctrl: Fix SNC detection
x86/topo: Fix SNC topology mess
x86/topo: Replace x86_has_numa_in_package
x86/topo: Add topology_num_nodes_per_package()
x86/numa: Store extra copy of numa_nodes_parsed
x86/boot: Handle relative CONFIG_EFI_SBAT_FILE file paths
x86/sev: Allow IBPB-on-Entry feature for SNP guests
x86/boot/sev: Move SEV decompressor variables into the .data section
permissive for auxiliary clocks, to not reject syscalls
based on the status field that do not try to modify the
status field. This makes ABI behavior in clock_adjtime()
consistent with CLOCK_REALTIME.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=zjov
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Make clock_adjtime() syscall timex validation slightly more permissive
for auxiliary clocks, to not reject syscalls based on the status field
that do not try to modify the status field.
This makes the ABI behavior in clock_adjtime() consistent with
CLOCK_REALTIME"
* tag 'timers-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Fix timex status validation for auxiliary clocks
PI and setscheduler() syscalls, resulting in kernel warnings
and misbehavior. Found during stress-testing.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vP5l
-----END PGP SIGNATURE-----
Merge tag 'sched-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix a DL scheduler bug that may corrupt internal metrics during PI and
setscheduler() syscalls, resulting in kernel warnings and misbehavior.
Found during stress-testing"
* tag 'sched-urgent-2026-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Fix missing ENQUEUE_REPLENISH during PI de-boosting
Saves two function calls, and one stac/clac pair.
stac/clac is rather expensive on older cpus like Zen 2.
A synthetic network stress test gives a ~1.5% increase of pps
on AMD Zen 2.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kuniyuki Iwashima <kuniyu@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two core changes and the rest in drivers, one core change to quirk the
behaviour of the Iomega Zip drive and one to fix a hang caused by tag
reallocation problems, which has mostly been seen by the iscsi client.
Note the latter fixes the problem but still has a slight sysfs memory
leak, so will be amended in the next pull request (once we've run the
fix for the fix through our testing).
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iLgEABMIAGAWIQTnYEDbdso9F2cI+arnQslM7pishQUCaaxT0hsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMiwyLDImHGphbWVzLmJvdHRvbWxleUBoYW5zZW5wYXJ0bmVy
c2hpcC5jb20ACgkQ50LJTO6YrIVmDwD+P17JCAk+Ju0aNSnjEmIjUC2oI1S+9GdO
thbkK99vClABAOOkDvHopBBhfsilTpHBYjWFM34vC/iiaO/xfgd9YH2A
=kIDx
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two core changes and the rest in drivers, one core change to quirk the
behaviour of the Iomega Zip drive and one to fix a hang caused by tag
reallocation problems, which has mostly been seen by the iscsi client.
Note the latter fixes the problem but still has a slight sysfs memory
leak, so will be amended in the next pull request (once we've run the
fix for the fix through our testing)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: Fix recursive locking in __configfs_open_file()
scsi: devinfo: Add BLIST_SKIP_IO_HINTS for Iomega ZIP
scsi: mpi3mr: Clear reset history on ready and recheck state after timeout
scsi: core: Fix refcount leak for tagset_refcnt
Silence build error in au1100fb driver found by kernel test robot
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCaayLiwAKCRD3ErUQojoP
X1pVAP4/j6LjBX862nFgtxS5XC4YBkpGRLYwO2WJMec+4sO5fQD/ThrowpuzZfPl
FhD/6WtMS4zPCDfNeqIKAo/JySez+w8=
=2Tha
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fix from Helge Deller:
"Silence build error in au1100fb driver found by kernel test robot"
* tag 'fbdev-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: au1100fb: Fix build on MIPS64
Three initial kernel mapping fixes
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCaayE4AAKCRD3ErUQojoP
X4U4AQDtHPc9nlM3areu5yTQnOcPTExuEoIpvBm9ktwNCdrwCgEAt4tqv3hhxCvG
/lwb6XBCHfyw3d/AsTRbOIH1MGCnaQQ=
=itGt
-----END PGP SIGNATURE-----
Merge tag 'parisc-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"While testing Sasha Levin's 'kallsyms: embed source file:line info in
kernel stack traces' patch series, which increases the typical kernel
image size, I found some issues with the parisc initial kernel mapping
which may prevent the kernel to boot.
The three small patches here fix this"
* tag 'parisc-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix initial page table creation for boot
parisc: Check kernel mapping earlier at bootup
parisc: Increase initial mapping to 64 MB with KALLSYMS
Fix a regression in RCU torture test pre-defined scenarios caused by
commit 7dadeaa6e8 ("sched: Further restrict the preemption modes")
which limits PREEMPT_NONE to architectures that do not support
preemption at all and PREEMPT_VOLUNTARY to those architectures that do
not yet have PREEMPT_LAZY support. Since major architectures (e.g. x86
and arm64) no longer support CONFIG_PREEMPT_NONE and
CONFIG_PREEMPT_VOLUNTARY, using them in rcutorture, rcuscale, refscale,
and scftorture pre-defined scenarios causes config checking errors.
Hence switch these kconfigs to PREEMPT_LAZY.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCAAvFiEEj5IosQTPz8XU1wRHSXnow7UH+rgFAmmsZu0RHGJvcXVuQGtl
cm5lbC5vcmcACgkQSXnow7UH+rgNWwgAn1bIWDIWQR9CkRQ0grhdO+pPfLusbVg/
Y7H3SsdEX03meSunA/IVGejP6Qbanuab9nyHdv3WxxowpCGYBaLFPvklSfcBWYeZ
4lxi6Fj+2rrzvOnQ54Pk5i4v5VayxEo12XBIgx6HDV7+5LgWk0gU0LpWPUhEWYYR
z/zJ/XbcLr8e9tZVwAWZj/ShLUH301razC2SaR/OlS93zqRG9Sd251Knjqq/lEwI
T6RZfhT2Wz3bgqU3QcjxDWw5dhB0/Y9wKoJjx4bB9m8lnSt+o96gH40TO+lnllnS
T4OHjqK1J1fUXNLzQufyfKKAiwi/LBBc9H4pe4tiLFxg0fg5s21flQ==
=NBys
-----END PGP SIGNATURE-----
Merge tag 'rcu-fixes.v7.0-20260307a' of git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux
Pull RCU selftest fixes from Boqun Feng:
"Fix a regression in RCU torture test pre-defined scenarios caused by
commit 7dadeaa6e8 ("sched: Further restrict the preemption modes")
which limits PREEMPT_NONE to architectures that do not support
preemption at all and PREEMPT_VOLUNTARY to those architectures that do
not yet have PREEMPT_LAZY support.
Since major architectures (e.g. x86 and arm64) no longer support
CONFIG_PREEMPT_NONE and CONFIG_PREEMPT_VOLUNTARY, using them in
rcutorture, rcuscale, refscale, and scftorture pre-defined scenarios
causes config checking errors.
Switch these kconfigs to PREEMPT_LAZY"
* tag 'rcu-fixes.v7.0-20260307a' of git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux:
scftorture: Update due to x86 not supporting none/voluntary preemption
refscale: Update due to x86 not supporting none/voluntary preemption
rcuscale: Update due to x86 not supporting none/voluntary preemption
rcutorture: Update due to x86 not supporting none/voluntary preemption
- Fix possible NULL pointer dereference in trace_data_alloc()
On the error path in trace_data_alloc(), it can call trigger_data_free()
with a NULL pointer. This use to be a kfree() but was changed to
trigger_data_free() to clean up any partial initialization. The issue is
that trigger_data_free() does not expect a NULL pointer. Have
trigger_data_free() return safely on NULL pointer.
- Fix multiple events on the command line and bootconfig
If multiple events are enabled on the command line separately and not
grouped, only the last event gets enabled. That is:
trace_event=sched_switch trace_event=sched_waking
Will only enable sched_waking where as:
trace_event=sched_switch,sched_waking
Will enable both.
The bootconfig makes it even worse as the second way is the more common
method.
The issue is that a temporary buffer is used to store the events to enable
later in boot. Each time the cmdline callback is called, it overwrites
what was previously there.
Have the callback append the next value (delimited by a comma) if the
temporary buffer already has content.
- Fix command line trace_buffer_size if >= 2G
The logic to allocate the trace buffer uses "int" for the size parameter
in the command line code causing overflow issues if more that 2G is
specified.
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCaaxEIRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qn+QAQCM6aJm0ZqDD2dM262M1mQpkU7sW3Dz
hZfBpo3YlH55fQEAklsaD96+yKN7PLl1Vh4c0zCelMHZA7kgck/3GqaFAgA=
=rn/Z
-----END PGP SIGNATURE-----
Merge tag 'trace-v7.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix possible NULL pointer dereference in trace_data_alloc()
On the trace_data_alloc() error path, it can call trigger_data_free()
with a NULL pointer. This used to be a kfree() but was changed to
trigger_data_free() to clean up any partial initialization. The issue
is that trigger_data_free() does not expect a NULL pointer. Have
trigger_data_free() return safely on NULL pointer.
- Fix multiple events on the command line and bootconfig
If multiple events are enabled on the command line separately and not
grouped, only the last event gets enabled. That is:
trace_event=sched_switch trace_event=sched_waking
will only enable sched_waking whereas:
trace_event=sched_switch,sched_waking
will enable both.
The bootconfig makes it even worse as the second way is the more
common method.
The issue is that a temporary buffer is used to store the events to
enable later in boot. Each time the cmdline callback is called, it
overwrites what was previously there.
Have the callback append the next value (delimited by a comma) if the
temporary buffer already has content.
- Fix command line trace_buffer_size if >= 2G
The logic to allocate the trace buffer uses "int" for the size
parameter in the command line code causing overflow issues if more
that 2G is specified.
* tag 'trace-v7.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix trace_buf_size= cmdline parameter with sizes >= 2G
tracing: Fix enabling multiple events on the kernel command line and bootconfig
tracing: Add NULL pointer check to trigger_data_free()
The "|| echo -lzstd" default makes zstd an unconditional link
dependency of resolve_btfids. On systems where libzstd-dev is not
installed and pkg-config fails, the linker fails:
ld: cannot find -lzstd: No such file or directory
libzstd is a transitive dependency of libelf, so the -lzstd flag is
strictly necessary only for static builds [1].
Remove ZSTD_LIBS variable, and instead set LIBELF_LIBS depending on
whether the build is static or not. Use $(HOSTPKG_CONFIG) as primary
source of the flags list.
Also add a default value for HOSTPKG_CONFIG in case it's not built via
the toplevel Makefile. Pass it from selftests/bpf too.
[1] https://lore.kernel.org/bpf/4ff82800-2daa-4b9f-95a9-6f512859ee70@linux.dev/
Reported-by: BPF CI Bot (Claude Opus 4.6) <bot+bpf-ci@kernel.org>
Reported-by: Vitaly Chikunov <vt@altlinux.org>
Closes: https://lore.kernel.org/bpf/aaWqMcK-2AQw5dx8@altlinux.org/
Fixes: 4021848a90 ("selftests/bpf: Pass through build flags to bpftool and resolve_btfids")
Signed-off-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Reviewed-by: Paul Chaignon <paul.chaignon@gmail.com>
Link: https://lore.kernel.org/r/20260305014730.3123382-1-ihor.solodrai@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
- aht10: Fix initialization commands for AHT20
- emc1403: correct a malformed email address
- it87: Check the it87_lock() return value
- max6639: fix inverted polarity
- macsmc: Fix overflows, underflows, sign extension, and other problems
- pmbus/q54sj108a2: fix stack overflow in debugfs read
- Drop support for SMARC-sAM67 (discontinued and never released to market)
-----BEGIN PGP SIGNATURE-----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=+l89
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix initialization commands for AHT20
- Correct a malformed email address (emc1403)
- Check the it87_lock() return value
- Fix inverted polarity (max6639)
- Fix overflows, underflows, sign extension, and other problems in
macsmc
- Fix stack overflow in debugfs read (pmbus/q54sj108a2)
- Drop support for SMARC-sAM67 (discontinued and never released to
market)
* tag 'hwmon-for-v7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (pmbus/q54sj108a2) fix stack overflow in debugfs read
hwmon: (max6639) fix inverted polarity
dt-bindings: hwmon: sl28cpld: Drop sa67mcu compatible
hwmon: (it87) Check the it87_lock() return value
Revert "hwmon: add SMARC-sAM67 support"
hwmon: (aht10) Fix initialization commands for AHT20
hwmon: (emc1403) correct a malformed email address
hwmon: (macsmc) Fix overflows, underflows, and sign extension
hwmon: (macsmc) Fix regressions in Apple Silicon SMC hwmon driver
- Revert "driver core: enforce device_lock for driver_match_device()":
When a device is already present in the system and a driver is
registered on the same bus, we iterate over all devices registered on
this bus to see if one of them matches. If we come across an already
bound one where the corresponding driver crashed while holding the
device lock (e.g. in probe()) we can't make any progress anymore.
Thus, revert and clarify that an implementer of struct bus_type must
not expect match() to be called with the device lock held.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS2q/xV6QjXAdC7k+1FlHeO1qrKLgUCaawGIAAKCRBFlHeO1qrK
LmYsAP0XzV/dZVrEqU5AvchbcuZ7kfAKotj4wPUIAkoT3gzMcQEAqNm7Vaf2ulDs
CS8XvRi0PX6inD1Oo3dqwb0rKjKfFwY=
=GT+5
-----END PGP SIGNATURE-----
Merge tag 'driver-core-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core fix from Danilo Krummrich:
- Revert "driver core: enforce device_lock for driver_match_device()":
When a device is already present in the system and a driver is
registered on the same bus, we iterate over all devices registered on
this bus to see if one of them matches. If we come across an already
bound one where the corresponding driver crashed while holding the
device lock (e.g. in probe()) we can't make any progress anymore.
Thus, revert and clarify that an implementer of struct bus_type must
not expect match() to be called with the device lock held.
* tag 'driver-core-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
Revert "driver core: enforce device_lock for driver_match_device()"
-----BEGIN PGP SIGNATURE-----
iJEEABYKADkWIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCaav3pBsUgAAAAAAEAA5t
YW51MiwyLjUrMS4xMSwyLDIACgkQgFxhu0/YY75xWwD+NO/7WX01zcYSFMHTjHRx
okbOkBwFzcZK+p/L4iTtVv0BAIYPUpa+RBLR2RtYN7mQEw8KO5yVgiLP2nlQYwIf
wZcH
=DrUe
-----END PGP SIGNATURE-----
Merge tag 'for-linus-7.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- a cleanup of arch/x86/kernel/head_64.S removing the pre-built page
tables for Xen guests
- a small comment update
- another cleanup for Xen PVH guests mode
- fix an issue with Xen PV-devices backed by driver domains
* tag 'for-linus-7.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: better handle backend crash
xenbus: add xenbus_device parameter to xenbus_read_driver_state()
x86/PVH: Use boot params to pass RSDP address in start_info page
x86/xen: update outdated comment
xen/acpi-processor: fix _CST detection using undersized evaluation buffer
x86/xen: Build identity mapping page tables dynamically for XENPV
Eduard Zingerman says:
====================
bpf: Fix precision backtracking bug with linked registers
Emil Tsalapatis reported a verifier bug hit by the scx_lavd sched_ext
scheduler. The essential part of the verifier log looks as follows:
436: ...
// checkpoint hit for 438: (1d) if r7 == r8 goto ...
frame 3: propagating r2,r7,r8
frame 2: propagating r6
mark_precise: frame3: last_idx ...
mark_precise: frame3: regs=r2,r7,r8 stack= before 436: ...
mark_precise: frame3: regs=r2,r7 stack= before 435: ...
mark_precise: frame3: regs=r2,r7 stack= before 434: (85) call bpf_trace_vprintk#177
verifier bug: backtracking call unexpected regs 84
The log complains that registers r2 and r7 are tracked as precise
while processing the bpf_trace_vprintk() call in precision backtracking.
This can't be right, as r2 is reset by the call and there is nothing
to backtrack it to. The precision propagation is triggered when
a checkpoint is hit at instruction 438, r2 is dead at that instruction.
This happens because of the following sequence of events:
- Instruction 438 is first reached with registers r2 and r7 having
the same id via a path that does not call bpf_trace_vprintk():
- Checkpoint is created at 438.
- The jump at 438 is predicted, hence r7 and registers linked to it
(r2) are propagated as precise, marking r2 and r7 precise in the
checkpoint.
- Instruction 438 is reached a second time with r2 undefined and via
a path that calls bpf_trace_vprintk():
- Checkpoint is hit.
- propagate_precision() picks registers r2 and r7 and propagates
precision marks for those up to the helper call.
The root cause is the fact that states_equal() and
propagate_precision() assume that the precision flag can't be set for a
dead register (as computed by compute_live_registers()).
However, this is not the case when linked registers are at play.
Fix this by accounting for live register flags in
collect_linked_regs().
---
====================
Link: https://patch.msgid.link/20260306-linked-regs-and-propagate-precision-v1-0-18e859be570d@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a test for the scenario described in the previous commit:
an iterator loop with two paths where one ties r2/r7 via
shared scalar id and skips a call, while the other goes
through the call. Precision marks from the linked registers
get spuriously propagated to the call path via
propagate_precision(), hitting "backtracking call unexpected
regs" in backtrack_insn().
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20260306-linked-regs-and-propagate-precision-v1-2-18e859be570d@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Fix an inconsistency between func_states_equal() and
collect_linked_regs():
- regsafe() uses check_ids() to verify that cached and current states
have identical register id mapping.
- func_states_equal() calls regsafe() only for registers computed as
live by compute_live_registers().
- clean_live_states() is supposed to remove dead registers from cached
states, but it can skip states belonging to an iterator-based loop.
- collect_linked_regs() collects all registers sharing the same id,
ignoring the marks computed by compute_live_registers().
Linked registers are stored in the state's jump history.
- backtrack_insn() marks all linked registers for an instruction
as precise whenever one of the linked registers is precise.
The above might lead to a scenario:
- There is an instruction I with register rY known to be dead at I.
- Instruction I is reached via two paths: first A, then B.
- On path A:
- There is an id link between registers rX and rY.
- Checkpoint C is created at I.
- Linked register set {rX, rY} is saved to the jump history.
- rX is marked as precise at I, causing both rX and rY
to be marked precise at C.
- On path B:
- There is no id link between registers rX and rY,
otherwise register states are sub-states of those in C.
- Because rY is dead at I, check_ids() returns true.
- Current state is considered equal to checkpoint C,
propagate_precision() propagates spurious precision
mark for register rY along the path B.
- Depending on a program, this might hit verifier_bug()
in the backtrack_insn(), e.g. if rY ∈ [r1..r5]
and backtrack_insn() spots a function call.
The reproducer program is in the next patch.
This was hit by sched_ext scx_lavd scheduler code.
Changes in tests:
- verifier_scalar_ids.c selftests need modification to preserve
some registers as live for __msg() checks.
- exceptions_assert.c adjusted to match changes in the verifier log,
R0 is dead after conditional instruction and thus does not get
range.
- precise.c adjusted to match changes in the verifier log, register r9
is dead after comparison and it's range is not important for test.
Reported-by: Emil Tsalapatis <emil@etsalapatis.com>
Fixes: 0fb3cf6110 ("bpf: use register liveness information for func_states_equal")
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20260306-linked-regs-and-propagate-precision-v1-1-18e859be570d@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
- Split out .modinfo section from ELF_DETAILS macro, as that macro may
be used in other areas that expect to discard .modinfo, breaking
certain image layouts
- Adjust genksyms parser to handle optional attributes in certain
declarations, necessary after commit 07919126ec ("netfilter:
annotate NAT helper hook pointers with __rcu")
- Include resolve_btfids in external module build created by
scripts/package/install-extmod-build when it may be run on
external modules
- Avoid removing objtool binary with 'make clean', as it is required for
external module builds
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR74yXHMTGczQHYypIdayaRccAalgUCaat33gAKCRAdayaRccAa
lizMAQCxm0P5WsJf3ydYR+5ZzzM7wreNtpMVMXsCbwOKBGY3VwEAyvB7om1a00Ex
Z6WFa9P4VKW+L4PWMnWoyxcnvl/CdgM=
=mvIb
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild fixes from Nathan Chancellor:
- Split out .modinfo section from ELF_DETAILS macro, as that macro may
be used in other areas that expect to discard .modinfo, breaking
certain image layouts
- Adjust genksyms parser to handle optional attributes in certain
declarations, necessary after commit 07919126ec ("netfilter:
annotate NAT helper hook pointers with __rcu")
- Include resolve_btfids in external module build created by
scripts/package/install-extmod-build when it may be run on external
modules
- Avoid removing objtool binary with 'make clean', as it is required
for external module builds
* tag 'kbuild-fixes-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Leave objtool binary around with 'make clean'
kbuild: install-extmod-build: Package resolve_btfids if necessary
genksyms: Fix parsing a declarator with a preceding attribute
kbuild: Split .modinfo out from ELF_DETAILS
- Fix kexec/hibernation hang due to bogus read-only mappings.
- Fix sparse warnings in our cmpxchg() implementation.
- Prevent runtime-const being used in modules, just like x86.
- Fix broken elision of access flag modifications for contiguous entries
on systems without support for hardware updates.
- Fix a broken SVE selftest that was testing the wrong instruction.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmmrH5wQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNLiWB/40+A3Q3gz9VB3obupFeC/s688TjGMwLbIO
m03Qu/ulGwBZaPRPZxsxnr8pFZKjSple5NJiHv5kQ/wR4Cfc4zwF2zOSdRvAI/c3
qPT2YL0CcVt0OgbWd2VCjiThTuFREewdCqRWbmkDaPYd27k0KWY14gHHpriRw7XM
QY0OOz8wrWi3lg2Wyvub9wWLkyjKtFlrkwZaACD5D90k/CwKVgncC1z4vh41hQxk
qjxdygNJt2sV+31+F7QMoY/rbyVnUkdSvWSwe9z2Bs9mwebaoGgx4c1l47Wq+oQD
NiVgHOZnPQkDgd2MWkUiCwzAr6C3B0aF2BCu+NTgILkbX7PyG792
=knFu
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main changes are a fix to the way in which we manage the access
flag setting for mappings using the contiguous bit and a fix for a
hang on the kexec/hibernation path.
Summary:
- Fix kexec/hibernation hang due to bogus read-only mappings
- Fix sparse warnings in our cmpxchg() implementation
- Prevent runtime-const being used in modules, just like x86
- Fix broken elision of access flag modifications for contiguous
entries on systems without support for hardware updates
- Fix a broken SVE selftest that was testing the wrong instruction"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
selftest/arm64: Fix sve2p1_sigill() to hwcap test
arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults
arm64: make runtime const not usable by modules
arm64: mm: Add PTE_DIRTY back to PAGE_KERNEL* to fix kexec/hibernation
arm64: Silence sparse warnings caused by the type casting in (cmp)xchg
Some of the sizing logic through tracer_alloc_buffers() uses int
internally, causing unexpected behavior if the user passes a value that
does not fit in an int (on my x86 machine, the result is uselessly tiny
buffers).
Fix by plumbing the parameter's real type (unsigned long) through to the
ring buffer allocation functions, which already use unsigned long.
It has always been possible to create larger ring buffers via the sysfs
interface: this only affects the cmdline parameter.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/bff42a4288aada08bdf74da3f5b67a2c28b761f8.1772852067.git.calvin@wbinvd.org
Fixes: 73c5162aa3 ("tracing: keep ring buffer to minimum size till used")
Signed-off-by: Calvin Owens <calvin@wbinvd.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Eduard Zingerman says:
====================
bpf: Fix u32/s32 bounds when ranges cross min/max boundary
Cover the following cases in range refinement logic for 32-bit ranges:
- s32 range crosses U32_MAX/0 boundary, positive part of the s32 range
overlaps with u32 range.
- s32 range crosses U32_MAX/0 boundary, negative part of the s32 range
overlaps with u32 range.
These cases are already handled for 64-bit range refinement.
Without the fix the test in patch 2 is rejected by the verifier.
The test was reduced from sched-ext program.
Changelog:
- v2 -> v3:
- Reverted da653de268 (Paul)
- Removed !BPF_F_TEST_REG_INVARIANTS flag from
crossing_32_bit_signed_boundary_2() (Paul)
- v1 -> v2:
- Extended commit message and comments (Emil)
- Targeting 'bpf' tree instead of bpf-next (Alexei)
v1: https://lore.kernel.org/bpf/9a23fbacdc6d33ec8fcb3f6988395b5129f75369.camel@gmail.com/T
v2: https://lore.kernel.org/bpf/20260305-bpf-32-bit-range-overflow-v2-0-7169206a3041@gmail.com/
---
====================
Link: https://patch.msgid.link/20260306-bpf-32-bit-range-overflow-v3-0-f7f67e060a6b@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
