The vendor prefix for Hardkernel ODROID-M1 is incorrectly listed as
rockchip. Use the proper hardkernel vendor prefix for this board, while
at it also drop the redundant soc prefix.
Fixes: 19cc53eb2c ("dt-bindings: rockchip: Add Hardkernel ODROID-M1 board")
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240827211825.1419820-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the necessary device tree changes to enable analog audio
output for the 3.5 mm TRS headphone jack on the Radxa ROCK 4C+ with
its RK809 audio codec.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Link: https://lore.kernel.org/r/20240828074755.1320692-1-net147@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3588 has 4 Hantro G1 encoder-only cores. They are all independent IP,
but can be used as a cluster (i.e. sharing work between the cores).
These cores are called VEPU121 in the TRM. The TRM describes one more
VEPU121, but that is combined with a Hantro H1. That one will be handled
using the VPU binding instead.
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240827181206.147617-2-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add device tree overlay for the WolfVision PF5 Visualizer display.
Since there shall be additional variants of the WolfVision PF5 display in
future, move common definitions to a device tree include file.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20240412-feature-wolfvision-pf5-display-v1-1-f032f32dba1a@wolfvision.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The reset-names property is not part of the binding, so drop it.
It is also not used by the driver, so that property was likely
a leftover from some vendor-kernel node.
Fixes: afeccc4084 ("arm64: dts: rockchip: add DT entry for RNG to RK356x")
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240815162519.751193-1-heiko@sntech.de
The device contains two i2c-connected eeproms holding some product-
specific values. One sitting on the mainboard and one on the statically
connected backplane.
While the eeprom chips themself have a size of 512 byte, the eeprom data
only uses 256 byte each, probably to stay compatible with other models.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240810211438.286441-3-heiko@sntech.de
The R2S Plus is basically an R2S with additional eMMC.
The eMMC configuration for the DTS has been extracted and copied from
rk3328-nanopi-r2.dts, v2017.09 branch from the friendlyarm/uboot-rockchip
repository.
Signed-off-by: Sergey Bostandzhyan <jin@mediatomb.cc>
Link: https://lore.kernel.org/r/20240814170048.23816-2-jin@mediatomb.cc
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the NanoPi R2S Plus variant, which is an R2S with eMMC.
Signed-off-by: Sergey Bostandzhyan <jin@mediatomb.cc>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240814170048.23816-3-jin@mediatomb.cc
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
since dr_mode = "otg" can be used for USB gadget functions for U-Boot
and Linux, there is no reason to set it to "peripheral". drop it.
Fixes: 1a5c8d307c ("arm64: dts: rockchip: Add Radxa ZERO 3W/3E")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20240802051508.498-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Increase the frequency of the PWM signal that drives the LED backlight of
the Pinebook Pro's panel, from about 1.35 KHz (which equals to the PWM
period of 740,740 ns), to exactly 8 kHz (which equals to the PWM period of
125,000 ns). Using a higher PWM frequency for the panel backlight, which
reduces the flicker, can only be beneficial to the end users' eyes.
On top of that, increasing the backlight PWM signal frequency reportedly
eliminates the buzzing emitted from the Pinebook Pro's built-in speakers
when certain backlight levels are set, which cause some weird interference
with some of the components of the Pinebook Pro's audio chain.
The old value for the backlight PWM period, i.e. 740,740 ns, is pretty much
an arbitrary value that was selected during the very early bring-up of the
Pinebook Pro, only because that value seemed to minimize horizontal line
distortion on the display, which resulted from the old X.org drivers causing
screen tearing when dragging windows around. That's no longer an issue, so
there are no reasons to stick with the old PWM period value.
The lower and the upper backlight PWM frequency limits for the Pinebook Pro's
panel, according to its datasheet, are 200 Hz and 10 kHz, respectively. [1]
These changes still leave some headroom, which may have some positive effects
on the lifetime expectancy of the panel's backlight LEDs.
[1] https://files.pine64.org/doc/datasheet/PinebookPro/NV140FHM-N49_Rev.P0_20160804_201710235838.pdf
Fixes: 5a65505a69 ("arm64: dts: rockchip: Add initial support for Pinebook Pro")
Cc: stable@vger.kernel.org
Reported-by: Nikola Radojevic <nikola@radojevic.rs>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Tested-by: Nikola Radojević <nikola@radojevic.rs>
Link: https://lore.kernel.org/r/2a23b6cfd8c0513e5b233b4006ee3d3ed09b824f.1722805655.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cool Pi CM5 GenBook works as a carrier board connect with CM5 [0].
Specification:
- Rockchip RK3588
- LPDDR5X 8/32 GB
- eMMC 64 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for RTL8852BE Wireless connection
- PCIE M.2 M Key for NVME connection
- eDP panel with 1920x1080
This patch add basic support to bringup eMMC/USB HOST/WiFi/TouchPad/
Battery/PCIE NVME, and can also drive a HDMI output with out of tree
hdmi patches.
[0] https://www.crowdsupply.com/shenzhen-tianmao-technology-co-ltd/genbook-rk3588
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20240730102433.540260-3-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add Cool Pi CM5 GenBook, a laptop powered by RK3588.
Cool Pi GenBook works with a carrier board connect with CM5.
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240730102433.540260-2-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This follows the same logic as 82d40b141a ("arm64: dts: rockchip: add
rfkill node for M.2 Key E WiFi on rock-5b").
On the orangepi-5-plus, there's also a GPIO pin connecting the WiFi
enable signal inside the M.2 Key E slot.
The exact GPIO PIN can be validated in the Armbian rk-5.10-rkr4 kernel
rk3588-orangepi-5-plus.dtsi file [1], which contains a `wifi_disable`
node referencing RK_PC4 on &gpio0.
With this change, I was able to get a "Intel Corporation Wi-Fi
6E(802.11ax) AX210/AX1675* 2x2 [Typhoon Peak] (rev 1a)" up, while
`rfkill` previously only mentioned to be hardware blocked.
[1] 9fbe23c9da/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts
Signed-off-by: Florian Klink <flokli@flokli.de>
Link: https://lore.kernel.org/r/20240808103052.1894764-1-flokli@flokli.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Contrary to the vendor-kernel the pmu-io-domains are not enabled by
default. This resulted in the value not being set according to the
regulator, which in turn made the gmac0 interface that is connected
to the vccio4 supply inoperable.
Fixes: 64b7f16fb3 ("arm64: dts: rockchip: add 2 pmu_io_domain supplies for Qnap-TS433")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240805162052.3345768-1-heiko@sntech.de
While it requires to have the right phy driver loaded (i.e. motorcomm)
to make the phy asserting the right delays, this is generally the
preferred way to define the MAC <-> PHY connection.
Signed-off-by: Uwe Kleine-König <ukleinek@debian.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240304084612.711678-2-ukleinek@debian.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rename the Rockchip RK3399 SoC dtsi files and, consequently, adjust their
contents and the contents of the affected board dts(i) files appropriately,
to "encapsulate" the different CPU and GPU OPPs for each of the supported
RK3399 SoC variants into the respective SoC variant dtsi files.
Moving the OPPs to the SoC variant dtsi files, instead of requiring the
board dts(i) files to include both the SoC variant dtsi file and the right
OPP variant dtsi file, reduces the possibility for mismatched inclusion and
improves the overall hierarchical representation of data.
These changes follow the approach used for the Rockchip RK3588 SoC variants,
which was introduced and described further in commit def88eb4d8 ("arm64:
dts: rockchip: Prepare RK3588 SoC dtsi files for per-variant OPPs"). Please
see that commit for a more detailed explanation.
No functional changes are introduced, which was validated by decompiling and
comparing all affected dtb files before and after these changes. In more
detail, all decompiled dtb files remain exactly the same, except the files
list below, which results from all of them stemming from the same base board
dtsi file (rk3399-rock-pi-4.dtsi), while all of them include one of the three
different RK3399 SoC variant dtsi files by themselves:
- rk3399-rock-4se.dtb
- rk3399-rock-pi-4a.dtb
- rk3399-rock-pi-4a-plus.dtb
- rk3399-rock-pi-4b.dtb
- rk3399-rock-pi-4b-plus.dtb
- rk3399-rock-pi-4c.dtb
When compared with the decompiled original dtb files, these dtb files have
some of their blocks shuffled around a bit and some of their phandles have
different values, as a result of the changes to the order in which the
building blocks from the parent dtsi files are included into them, but they
still effectively remain the same as the originals.
The only exception to the "include only a SoC variant dtsi" is found in
rk3399-evb.dts, which includes rk3399-base.dtsi instead of rk3399.dtsi.
This is intentional, because this board dts file doesn't enable the TSADC,
so including rk3399.dtsi would enable the SoC to go into higher OPPs with
no thermal throttling in place. Let's hope that people interested in this
board will fix this in the future.
As a side note, due to the nature of introduced changes, this commit is best
viewed using the --break-rewrites option for git-log(1).
Related-to: def88eb4d8 ("arm64: dts: rockchip: Prepare RK3588 SoC dtsi files for per-variant OPPs")
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/9417b5c5b64f9aceea64530a85a536169a3e7466.1721532747.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the two supplies for the pmu-io-domains that are defined in the
vendor devicetree for the TS433.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-15-heiko@sntech.de
The TS433 doesn't provide display output, but the gpu nevertheless can be
used for compute tasks for example.
So there is no reason not to enable it.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-14-heiko@sntech.de
Fill in the missing pieces for RK809 pmic used on the TS433.
The regulator setup comes from the vendor-devicetree, so without proper
schematics its accuracy is somewhat unclear, but it looks really similar
to all the other rk3568 boards, so follows the reference design it seems.
The one caveat is related to vcc3v3_sd. This regulator needs to stay on.
When turned off because of no users, access to both PCIe controllers
will stall. Maybe this rail does supply the 100MHz refclk generation
or so.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-13-heiko@sntech.de
The TS433 seems to use a silergy,syr827 regulator for the cpu supply.
At least that is the compatible used in the vendor devicetree, though
it could very well also be another fan53555 clone.
Define the needed regulator node and hook up the cpu-supply to the
cpu cores.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-12-heiko@sntech.de
The TS433 has 3 buttons, power and copy in the front as well as a reset
pinhole button on the back. The power-button is connected to the embedded
controller while the other two buttons are just gpio connected.
Add the gpio-keys definition for the two buttons we can handle right now.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-11-heiko@sntech.de
Add the 4 gpio-controlled LEDs to the Qnap-TS433.
They are meant for individual disk activitivy, but I haven't found a
way for how to connect them to their individual sata slot yet.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-9-heiko@sntech.de
Add the aliases for the internal network interface as well as the emmc
on the board and make sure the dedicated RTC is always the first one.
The TS433 actually has two rtc devices. One coming from the rk809 pmic
without added functionality and also a dedicated RTC from Mycrocrystal
that is battery backed to keep the time.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-8-heiko@sntech.de
The TS433 has 4 bays. The last two are accessed via a pci-connected
sata controller, while the first two are accessed via the rk3568's
sata controllers. Enable these two now.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-7-heiko@sntech.de
As most Rockchip boards do, the TS433 also uses uart2 for its serial
output. Set the correct chosen entry for it.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-6-heiko@sntech.de
Enable usb controllers and phys and add regulator infrastructure for the
usb ports on the TS433.
Of course there are no schematics available for the device, so the
regulator information comes from the vendor-devicetree with unknown
accuracy.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-5-heiko@sntech.de
Uart0 is connected to an MCU on the board that handles system control
like the fan-speed. So far no driver for it is available though.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-4-heiko@sntech.de
The TS433 uses both pcie controllers for sata and the 2nd network
interface. Set the needed data-lanes in the pcie3 phy and enable
the second pcie controller, as well as remove the bifurcation comment.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-3-heiko@sntech.de
The DW MCI controller driver will use them to reset the IP block before
initialisation.
Fixes: d717f7352e ("arm64: dts: rockchip: add sdmmc/sdio/emmc nodes for RK3328 SoCs")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240710132830.14710-4-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3328 SoC has a fourth mmc controller called SDMMC_EXT. Some
boards have sdio wifi connected to it. In order to use it
one would have to add the pinctrls from sdmmc0ext group which
is done on board level.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240710132830.14710-3-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This board can work in UHS-I SDR-104 mode, but may not be stable,
use SDR-50 instead. Remove the max-frequency property, which is
already defined in rk356x.dtsi.
Fixes: c79dab407a ("arm64: dts: rockchip: Add Lunzn Fastrhino R66S")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20240710143017.685905-4-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since we use rgmii-id as the phy mode, remove the useless
tx_delay and rx_delay properties.
Fixes: b9f8ca655d ("arm64: dts: rockchip: Add Lunzn Fastrhino R68S")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20240710143017.685905-3-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Replace the deprecated snps,reset-xxx bindings to the generic Ethernet
PHY reset GPIO bindings. According to the PHY datasheet, the RTL8211F
PHY needs a 10ms assert delay and at least 72ms deassert delay.
Considering the possibility of mixed use of PHY chips, increased the
reset time.
Fixes: b9f8ca655d ("arm64: dts: rockchip: Add Lunzn Fastrhino R68S")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20240710143017.685905-2-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
All batches of the Pine64 Pinebook Pro, except the latest batch (as of 2024)
whose hardware design was revised due to the component shortage, use a 1S
lithium battery whose nominal/design capacity is 10,000 mAh, according to the
battery datasheet. [1][2] Let's correct the design full-charge value in the
Pinebook Pro board dts, to improve the accuracy of the hardware description,
and to hopefully improve the accuracy of the fuel gauge a bit on all units
that don't belong to the latest batch.
The above-mentioned latest batch uses a different 1S lithium battery with
a slightly lower capacity, more precisely 9,600 mAh. To make the fuel gauge
work reliably on the latest batch, a sample battery would need to be sent to
CellWise, to obtain its proprietary battery profile, whose data goes into
"cellwise,battery-profile" in the Pinebook Pro board dts. Without that data,
the fuel gauge reportedly works unreliably, so changing the design capacity
won't have any negative effects on the already unreliable operation of the
fuel gauge in the Pinebook Pros that belong to the latest batch.
According to the battery datasheet, its voltage can go as low as 2.75 V while
discharging, but it's better to leave the current 3.0 V value in the dts file,
because of the associated Pinebook Pro's voltage regulation issues.
[1] https://wiki.pine64.org/index.php/Pinebook_Pro#Battery
[2] https://files.pine64.org/doc/datasheet/pinebook/40110175P%203.8V%2010000mAh%E8%A7%84%E6%A0%BC%E4%B9%A6-14.pdf
Fixes: c7c4d698cd ("arm64: dts: rockchip: add fuel gauge to Pinebook Pro dts")
Cc: stable@vger.kernel.org
Cc: Marek Kraus <gamiee@pine64.org>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/731f8ef9b1a867bcc730d19ed277c8c0534c0842.1721065172.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Firefly Core-PX30-JD4 SoM is a 69.6x49.6mm (260 pin SODIMM connector)
system-on-module from Firefly, featuring the Rockchip PX30.
It provides the following feature set:
* on-module DDR3 (1GB/2GB)
* on-module eMMC 5.1 (8GB/16GB/32GB/64GB/128GB)
* on-module NPU (optional)
* SD card (on a baseboard) via edge connector
* 100mbps Ethernet (on a baseboard) via edge connector
* MIPI-DSI (on a baseboard) via edge connector
* Audio (on a baseboard) via edge connector
- 1x SPDIF
- 1x 8-channel I2S/TDM
- 1x 2-channel I2S/TDM
- 1x 8-channel PDM
* USB (on a baseboard) via edge connector
- 1x USB 2.0 OTG
- 1x USB 2.0 host
* Various GPIO (on a baseboard) via edge connector
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20240718-rockchip-px30-firefly-v3-2-3835cdd22eae@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add binding for the Firefly Core-PX30-JD4 SoM when used in conjunction
with the MB-JD4-PX30 baseboard.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240718-rockchip-px30-firefly-v3-1-3835cdd22eae@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Fix RPM package build error caused by an incorrect locale setup
- Mark modules.weakdep as ghost in RPM package
- Fix the odd combination of -S and -c in stack protector scripts, which
is an error with the latest Clang
-----BEGIN PGP SIGNATURE-----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=HYew
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix RPM package build error caused by an incorrect locale setup
- Mark modules.weakdep as ghost in RPM package
- Fix the odd combination of -S and -c in stack protector scripts,
which is an error with the latest Clang
* tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Fix '-S -c' in x86 stack protector scripts
kbuild: rpm-pkg: ghost modules.weakdep file
kbuild: rpm-pkg: Fix C locale setup
This simplifies the min_t() and max_t() macros by no longer making them
work in the context of a C constant expression.
That means that you can no longer use them for static initializers or
for array sizes in type definitions, but there were only a couple of
such uses, and all of them were converted (famous last words) to use
MIN_T/MAX_T instead.
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3a7e02c040 ("minmax: avoid overly complicated constant
expressions in VM code") added the simpler MIN_T/MAX_T macros in order
to avoid some excessive expansion from the rather complicated regular
min/max macros.
The complexity of those macros stems from two issues:
(a) trying to use them in situations that require a C constant
expression (in static initializers and for array sizes)
(b) the type sanity checking
and MIN_T/MAX_T avoids both of these issues.
Now, in the whole (long) discussion about all this, it was pointed out
that the whole type sanity checking is entirely unnecessary for
min_t/max_t which get a fixed type that the comparison is done in.
But that still leaves min_t/max_t unnecessarily complicated due to
worries about the C constant expression case.
However, it turns out that there really aren't very many cases that use
min_t/max_t for this, and we can just force-convert those.
This does exactly that.
Which in turn will then allow for much simpler implementations of
min_t()/max_t(). All the usual "macros in all upper case will evaluate
the arguments multiple times" rules apply.
We should do all the same things for the regular min/max() vs MIN/MAX()
cases, but that has the added complexity of various drivers defining
their own local versions of MIN/MAX, so that needs another level of
fixes first.
Link: https://lore.kernel.org/all/b47fad1d0cf8449886ad148f8c013dae@AcuMS.aculab.com/
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Many fixes for power-cut issues by Zhihao Cheng
- Another ubiblock error path fix
- ubiblock section mismatch fix
- Misc fixes all over the place
-----BEGIN PGP SIGNATURE-----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=0y6/
-----END PGP SIGNATURE-----
Merge tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
- Many fixes for power-cut issues by Zhihao Cheng
- Another ubiblock error path fix
- ubiblock section mismatch fix
- Misc fixes all over the place
* tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: Fix ubi_init() ubiblock_exit() section mismatch
ubifs: add check for crypto_shash_tfm_digest
ubifs: Fix inconsistent inode size when powercut happens during appendant writing
ubi: block: fix null-pointer-dereference in ubiblock_create()
ubifs: fix kernel-doc warnings
ubifs: correct UBIFS_DFS_DIR_LEN macro definition and improve code clarity
mtd: ubi: Restore missing cleanup on ubi_init() failure path
ubifs: dbg_orphan_check: Fix missed key type checking
ubifs: Fix unattached inode when powercut happens in creating
ubifs: Fix space leak when powercut happens in linking tmpfile
ubifs: Move ui->data initialization after initializing security
ubifs: Fix adding orphan entry twice for the same inode
ubifs: Remove insert_dead_orphan from replaying orphan process
Revert "ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path"
ubifs: Don't add xattr inode into orphan area
ubifs: Fix unattached xattr inode if powercut happens after deleting
mtd: ubi: avoid expensive do_div() on 32-bit machines
mtd: ubi: make ubi_class constant
ubi: eba: properly rollback inside self_check_eba
After a recent change in clang to stop consuming all instances of '-S'
and '-c' [1], the stack protector scripts break due to the kernel's use
of -Werror=unused-command-line-argument to catch cases where flags are
not being properly consumed by the compiler driver:
$ echo | clang -o - -x c - -S -c -Werror=unused-command-line-argument
clang: error: argument unused during compilation: '-c' [-Werror,-Wunused-command-line-argument]
This results in CONFIG_STACKPROTECTOR getting disabled because
CONFIG_CC_HAS_SANE_STACKPROTECTOR is no longer set.
'-c' and '-S' both instruct the compiler to stop at different stages of
the pipeline ('-S' after compiling, '-c' after assembling), so having
them present together in the same command makes little sense. In this
case, the test wants to stop before assembling because it is looking at
the textual assembly output of the compiler for either '%fs' or '%gs',
so remove '-c' from the list of arguments to resolve the error.
All versions of GCC continue to work after this change, along with
versions of clang that do or do not contain the change mentioned above.
Cc: stable@vger.kernel.org
Fixes: 4f7fd4d7a7 ("[PATCH] Add the -fstack-protector option to the CFLAGS")
Fixes: 60a5317ff0 ("x86: implement x86_32 stack protector")
Link: 6461e53781 [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Since ubiblock_exit() is now called from an init function,
the __exit section no longer makes sense.
Cc: Ben Hutchings <bwh@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407131403.wZJpd8n2-lkp@intel.com/
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Enable turbostat extensions to add both perf and PMT
(Intel Platform Monitoring Technology) counters via the cmdline.
Demonstrate PMT access with built-in support for Meteor Lake's Die%c6 counter.
-----BEGIN PGP SIGNATURE-----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=wsSy
-----END PGP SIGNATURE-----
Merge tag 'v6.11-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- Enable turbostat extensions to add both perf and PMT (Intel
Platform Monitoring Technology) counters via the cmdline
- Demonstrate PMT access with built-in support for Meteor Lake's
Die C6 counter
* tag 'v6.11-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: version 2024.07.26
tools/power turbostat: Include umask=%x in perf counter's config
tools/power turbostat: Document PMT in turbostat.8
tools/power turbostat: Add MTL's PMT DC6 builtin counter
tools/power turbostat: Add early support for PMT counters
tools/power turbostat: Add selftests for added perf counters
tools/power turbostat: Add selftests for SMI, APERF and MPERF counters
tools/power turbostat: Move verbose counter messages to level 2
tools/power turbostat: Move debug prints from stdout to stderr
tools/power turbostat: Fix typo in turbostat.8
tools/power turbostat: Add perf added counter example to turbostat.8
tools/power turbostat: Fix formatting in turbostat.8
tools/power turbostat: Extend --add option with perf counters
tools/power turbostat: Group SMI counter with APERF and MPERF
tools/power turbostat: Add ZERO_ARRAY for zero initializing builtin array
tools/power turbostat: Replace enum rapl_source and cstate_source with counter_source
tools/power turbostat: Remove anonymous union from rapl_counter_info_t
tools/power/turbostat: Switch to new Intel CPU model defines
New Changes:
- Refactor to a common struct for DRAM and general media CXL events
- Add abstract distance calculation support for CXL
- Add CXL maturity map documentation to detail current state of CXL enabling
- Add warning on mixed CXL VH and RCH/RCD hierachy to inform unsupported config
- Replace ENXIO with EBUSY for inject poison limit reached via debugfs
- Replace ENXIO with EBUSY for inject poison cxl-test support
- XOR math fixup for DPA to SPA translation. Current math works for MODULO arithmetic
where HPA==SPA, however not for XOR decode.
- Move pci config read in cxl_dvsec_rr_decode() to avoid unnecessary acess
Fixes:
- Add a fix to address race condition in CXL memory hotplug notifier
- Add missing MODULE_DESCRIPTION() for CXL modules
- Fix incorrect vendor debug UUID define
-----BEGIN PGP SIGNATURE-----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=HaEG
-----END PGP SIGNATURE-----
Merge tag 'cxl-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull CXL updates from Dave Jiang:
"Core:
- A CXL maturity map has been added to the documentation to detail
the current state of CXL enabling.
It provides the status of the current state of various CXL features
to inform current and future contributors of where things are and
which areas need contribution.
- A notifier handler has been added in order for a newly created CXL
memory region to trigger the abstract distance metrics calculation.
This should bring parity for CXL memory to the same level vs
hotplugged DRAM for NUMA abstract distance calculation. The
abstract distance reflects relative performance used for memory
tiering handling.
- An addition for XOR math has been added to address the CXL DPA to
SPA translation.
CXL address translation did not support address interleave math
with XOR prior to this change.
Fixes:
- Fix to address race condition in the CXL memory hotplug notifier
- Add missing MODULE_DESCRIPTION() for CXL modules
- Fix incorrect vendor debug UUID define
Misc:
- A warning has been added to inform users of an unsupported
configuration when mixing CXL VH and RCH/RCD hierarchies
- The ENXIO error code has been replaced with EBUSY for inject poison
limit reached via debugfs and cxl-test support
- Moving the PCI config read in cxl_dvsec_rr_decode() to avoid
unnecessary PCI config reads
- A refactor to a common struct for DRAM and general media CXL
events"
* tag 'cxl-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/core/pci: Move reading of control register to immediately before usage
cxl: Remove defunct code calculating host bridge target positions
cxl/region: Verify target positions using the ordered target list
cxl: Restore XOR'd position bits during address translation
cxl/core: Fold cxl_trace_hpa() into cxl_dpa_to_hpa()
cxl/test: Replace ENXIO with EBUSY for inject poison limit reached
cxl/memdev: Replace ENXIO with EBUSY for inject poison limit reached
cxl/acpi: Warn on mixed CXL VH and RCH/RCD Hierarchy
cxl/core: Fix incorrect vendor debug UUID define
Documentation: CXL Maturity Map
cxl/region: Simplify cxl_region_nid()
cxl/region: Support to calculate memory tier abstract distance
cxl/region: Fix a race condition in memory hotplug notifier
cxl: add missing MODULE_DESCRIPTION() macros
cxl/events: Use a common struct for DRAM and General Media events
