Writing the quad enable bit in one helper and doing the chip
configuration in another does not make much sense from a bus interface
setup point of view.
Instead, let's create a broader helper which is going to be in charge of
all the bus configuration steps at once. This will specifically allow to
transition to octal DDR mode, and even fallback to quad (if suppoorted)
or single mode otherwise.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When we will change the bus interface, the action that actually performs
the transition is the IO mode register write. This means after the IO
mode register write, we should use the new bus interface. But the
->configure_chip() hook itself is not responsible of making this change
official, it is the caller that must act according to the return value.
Reorganize this helper to first configure the dummy cycles before
possibly switching to another bus interface.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Provide the Winbond W35N specific "write VCR register" operation to let
the core verify it is supported by the controller before using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Provide the Winbond W25N specific "select target" operation to let the
core verify it is supported by the controller before using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Provide the Macronix specific "read ECC status register" operation so
that the core can verify if it is supported by the controller before
using it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It is probably safe to expect that all SPI controller drivers will ever
support all the most basic SPI NAND operations, such as write enable,
register reads, page program, block erases, etc. However, what about
vendor specific operations? So far nobody complained about it, but as we
are about to introduce octal DTR support, and as none of the SPI NAND
instruction set is defined in any standard, we must remain careful about
these extra operations.
One way to make sure we do not blindly get ourselves in strange
situations with vendor commands failing silently is to make the check
once for all, while probing the chip. However at this stage we have no
such list, so let's add the necessary infrastructure to allow:
- registering vendor operations,
- checking they are actually supported when appropriate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Winbond W35N* chips require a vendor specific operation to write their
VCR register (a configuration register, typically used for tuning the
number of dummy cycles and switching to a different bus
interface). Instead of defining this op only in the function that needs
it, hiding it from the core, make it a proper define like all other
spi-mem operations, and implement the necessary spinand_fill_*_op()
helper to make the SPINAND_OP() macro work. This way we can use it from
any function without any extra handling outside of this helper when we
will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Winbond W25N* chips require a vendor specific operation to select the
target. Instead of defining this op only in the function that
needs it, hiding it from the core, make it a proper define like all
other spi-mem operations, and implement the necessary
spinand_fill_*_op() helper to make the SPINAND_OP() macro work. This way
we can use it from any function without any extra handling outside of
this helper when we will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Macronix chips require a vendor specific operation to read the ECC
status register. Instead of defining this op only in the function that
needs it, hiding it from the core, make it a proper define like all
other spi-mem operations, and implement the necessary
spinand_fill_*_op() helper to make the SPINAND_OP() macro work. This way
we can use it from any function without any extra handling outside of
this helper when we will convert the core to support octal DDR busses.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Create a SPINAND_OP() macro to which we give the name of the operation
we want. This macro retrieves the correct operation template based on
the current bus interface (currently only single SDR, will soon be
extended to octal DTR) and fills it with the usual parameters.
This macro makes the transition from calling directly the low-level
macros into using the (bus interface dependent) templates very smooth.
Use it in all places that can be trivially converted. At this stage
there is no functional change expected, until octal DTR support gets
added.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, the SPI NAND core implementation directly calls macros to get
the various operations in shape. These macros are specific to the bus
interface, currently only supporting the single SDR interface (any
command following the 1S-XX-XX pattern).
Introducing support for other bus interfaces (such as octal DTR) would
mean that every user of these macros should become aware of the current
bus interface and act accordingly, picking up and adapting to the
current configuration. This would add quite a bit of boilerplate, be
repetitive as well as error prone in case we miss one occurrence.
Instead, let's create a table with all SPI NAND memory operations that
are currently supported. We initialize them with the same single SDR _OP
macros as before. This opens the possibility for users of the individual
macros to make use of these templates instead. This way, when we will add
another bus interface, we can just switch to another set of templates
and all users will magically fill in their spi_mem_op structures with
the correct ops.
The existing read, write and update cache variants are also moved in
this template array, which is barely noticeable by callers as we also
add a structure member pointing to it.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to introduce templates for all operations and not only for page
helpers (in order to introduce octal DDR support), decouple the WR_EN
and WR_DIS operations into two separate macros.
Adapt the callers accordingly.
There is no functional change.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace -ENOTSUPP with -EOPNOTSUPP which is as relevant in this case but
is standard.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SPI NAND command values are directly included in the macros defining the
ops. These are stale definitions, they are unused so drop them.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The update cache variant is mandatory, both read and write versions are
being checked, but not this one. All chip drivers seem to implement this
variant, so there should be no breakage.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The @data buffer is 5 bytes, not 4, it has been extended for the need of
devices with an extra ID bytes.
Fixes: 34a956739d ("mtd: spinand: Add support for 5-byte IDs")
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In octal DTR mode addresses may either be long enough to cover at least
two bytes (in which case the existing macro works), or otherwise for
single byte addresses, the byte must also be duplicated and sent twice:
on each front of the clock.
Create a macro for this common case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This series adds support for 8D-8D-8D in SPI NAND, which can already be
leveraged without any SPI changes as controllers already have this
support for some SPI NOR devices.
Among the few spi-mem patches, they are needed for building the SPI NAND
changes (especially the ODTR introduction at the end) and therefore an
immutable tag will be needed for merging in the MTD tree (unless all the
series goes through MTD directly ofc).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmlnfPIACgkQJNaLcl1U
h9CMnQf/aYcMZaDepnTHrvSeE4OVUuQGYK7zBVrIyrJXhuBrLkVQjESyQ85lgW1Y
GGaAYYaiSdHaeSZFnUNZxIgynAEAaNAHEHKHggBU6JZOCDYJvuTzj62mzYzaMDmf
x9rbgX9g9+Vzu0C0V62fArqVIjNcmJj2+X4VO50TII0f7iV8//Wf4L4B3bnob5vF
+N5fMLjlyGxohW7lHoSy0lDoMB/65XYk1NyDuErqzgSPxiJcnfRTxvH/8UyNY3Ks
A6ipG6RtGHkp2bo62mKlaTQZZoYG8oCFjAaLv3v9EI9oEDja+OqRb/Zd7CYH2PIP
ESMRf+Bl9sSmCZvcI/k514Qjata/XQ==
=YzKE
-----END PGP SIGNATURE-----
Merge tag 'tags/spi-octal-dtr' into nand/next
spi: Octal DTR support
This series adds support for 8D-8D-8D in SPI NAND, which can already be
leveraged without any SPI changes as controllers already have this
support for some SPI NOR devices.
Among the few spi-mem patches, they are needed for building the SPI NAND
changes (especially the ODTR introduction at the end) and therefore an
immutable tag will be needed for merging in the MTD tree (unless all the
series goes through MTD directly ofc).
Place the ofparts before RedBoot partitions in the OF probe
path: this makes it possible to override any existing
RedBoot partitions with fixed-partitions which may be necessary,
such as when you need to repartition the flash from Linux'
point of view but not necessary from the bootloaders point
of view.
This happens when a device such as Raidsonic IB-4220-B has
three partitions named "Kern", "Ramdisk" and "Application"
that we want to merge into one for more efficient use
of the flash memory in OpenWrt.
Signed-off-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_get_child_by_name() returns a node pointer with refcount incremented,
which must be released with of_node_put() when done. However, in
parse_fixed_partitions(), when dedicated is true (i.e., a "partitions"
subnode was found), the ofpart_node obtained from of_get_child_by_name()
is never released on any code path.
Add of_node_put(ofpart_node) calls on all exit paths when dedicated is
true to fix the reference count leak.
This bug was detected by our static analysis tool.
Fixes: 562b4e91d3 ("mtd: parsers: ofpart: fix parsing subpartitions")
Signed-off-by: Weigang He <geoffreyhe2@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- There's a 3 patch series from Pratyush Yadav which fixes a few things
in the new-in-6.19 LUO memfd code.
- Plus the usual shower of singletons - please see the changelogs for
details.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCaXub9wAKCRDdBJ7gKXxA
jjoHAP48ag3lmJnpej977MxrA4VUBhv6ATmbFE2+czCzbRJaigEAiIMWtUlSVYbH
WuEYQvcFeSR0hYjs0ClKUiZYOUcj+wI=
=lHEL
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2026-01-29-09-41' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes. 9 are cc:stable, 12 are for MM.
There's a patch series from Pratyush Yadav which fixes a few things in
the new-in-6.19 LUO memfd code.
Plus the usual shower of singletons - please see the changelogs for
details"
* tag 'mm-hotfixes-stable-2026-01-29-09-41' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
vmcoreinfo: make hwerr_data visible for debugging
mm/zone_device: reinitialize large zone device private folios
mm/mm_init: don't cond_resched() in deferred_init_memmap_chunk() if called from deferred_grow_zone()
mm/kfence: randomize the freelist on initialization
kho: kho_preserve_vmalloc(): don't return 0 when ENOMEM
kho: init alloc tags when restoring pages from reserved memory
mm: memfd_luo: restore and free memfd_luo_ser on failure
mm: memfd_luo: use memfd_alloc_file() instead of shmem_file_setup()
memfd: export alloc_file()
flex_proportions: make fprop_new_period() hardirq safe
mailmap: add entry for Viacheslav Bocharov
mm/memory-failure: teach kill_accessing_process to accept hugetlb tail page pfn
mm/memory-failure: fix missing ->mf_stats count in hugetlb poison
mm, swap: restore swap_space attr aviod kernel panic
mm/kasan: fix KASAN poisoning in vrealloc()
mm/shmem, swap: fix race of truncate and swap entry split
While reworking the LSM initialization code the
/proc/sys/vm/mmap_min_addr handler was inadvertently caught up in the
change and the procfs entry wasn't setup when CONFIG_SECURITY was not
selected at kernel build time. This patch restores the previous behavior
and ensures that the procfs entry is setup regardless of the
CONFIG_SECURITY state.
Future work will improve upon this, likely by moving the procfs handler
into the mm subsystem, but this patch should resolve the immediate
regression.
Fixes: 4ab5efcc28 ("lsm: consolidate all of the LSM framework initcalls")
Reported-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Tested-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Add QCA_CAP_HFP_HW_OFFLOAD capability flag to WCN6855 and WCN7850
device data structures to enable Hands-Free Profile (HFP) hardware
offload support on these Qualcomm Bluetooth chipsets.
Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace SoC-specific check with capability-based approach for HFP
hardware offload configuration. Add QCA_CAP_HFP_HW_OFFLOAD capability
flag and support_hfp_hw_offload field to qca_serdev structure. Add
QCA_CAP_HFP_HW_OFFLOAD capability flag to QCA2066 device data
structures.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This attempts to proper track outstanding request by using struct ida
and allocating from it in l2cap_get_ident using ida_alloc_range which
would reuse ids as they are free, then upon completion release
the id using ida_free.
This fixes the qualification test case L2CAP/COS/CED/BI-29-C which
attempts to check if the host stack is able to work after 256 attempts
to connect which requires Ident field to use the full range of possible
values in order to pass the test.
Link: https://github.com/bluez/bluez/issues/1829
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fix memory leak in set_ssp_complete() where mgmt_pending_cmd structures
are not freed after being removed from the pending list.
Commit 302a1f674c ("Bluetooth: MGMT: Fix possible UAFs") replaced
mgmt_pending_foreach() calls with individual command handling but missed
adding mgmt_pending_free() calls in both error and success paths of
set_ssp_complete(). Other completion functions like set_le_complete()
were fixed correctly in the same commit.
This causes a memory leak of the mgmt_pending_cmd structure and its
associated parameter data for each SSP command that completes.
Add the missing mgmt_pending_free(cmd) calls in both code paths to fix
the memory leak. Also fix the same issue in set_advertising_complete().
Fixes: 302a1f674c ("Bluetooth: MGMT: Fix possible UAFs")
Signed-off-by: Jianpeng Chang <jianpeng.chang.cn@windriver.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling
hci_uart_register_dev(), which calls proto->open() to initialize
hu->priv. However, if a TTY write wakeup occurs during this window,
hci_uart_tx_wakeup() may schedule write_work before hu->priv is
initialized, leading to a NULL pointer dereference in
hci_uart_write_work() when proto->dequeue() accesses hu->priv.
The race condition is:
CPU0 CPU1
---- ----
hci_uart_set_proto()
set_bit(HCI_UART_PROTO_INIT)
hci_uart_register_dev()
tty write wakeup
hci_uart_tty_wakeup()
hci_uart_tx_wakeup()
schedule_work(&hu->write_work)
proto->open(hu)
// initializes hu->priv
hci_uart_write_work()
hci_uart_dequeue()
proto->dequeue(hu)
// accesses hu->priv (NULL!)
Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open()
succeeds, ensuring hu->priv is initialized before any work can be
scheduled.
Fixes: 5df5dafc17 ("Bluetooth: hci_uart: Fix another race during initialization")
Link: https://lore.kernel.org/linux-bluetooth/6969764f.170a0220.2b9fc4.35a7@mx.google.com/
Signed-off-by: Jia-Hong Su <s11242586@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The USB device ID 0x13d3/0x3618 is listed twice in the device table.
Remove the duplicate entry and keep the one under the correct
"Realtek 8852BT/8852BE-VT Bluetooth devices" section.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add USB device ID 0x2c0a:0x8761 to the btusb driver fo the Realtek
RTL8761BU Bluetooth adapter.
Reference:
https://www.startech.com/en-us/networking-io/av53c1-usb-bluetooth
Signed-off-by: Jacopo Scannella <code@charlie.cat>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The functions are already disabled if CONFIG_PM or CONFIG_PM_SLEEP are
disabled through the use of SET_SYSTEM_SLEEP_PM_OPS() and
SET_RUNTIME_PM_OPS().
This increases build coverage and allows to drop a few #ifdef's.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The functions are already disabled through the use of pm_ptr() when
CONFIG_PM is disabled, and will be removed from the final linked code
as not needed.
This increases build coverage and allows to drop an #ifdef.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The kfree_skb() function internally checks if the skb is NULL,
so an explicit check before calling it is redundant and can be removed.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If USB autosuspend occurs while discovery is active, the ongoing
HCI operation may not complete successfully. On some devices, this
can leave discovery.state stuck in DISCOVERY_FINDING.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Export hci_discovery_active() so it can be used by bluetooth
drivers built as modules.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This increases build coverage and allows to drop an #ifdef.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit bd3f305886 ("dt-bindings: bluetooth: qualcomm: describe the
inputs from PMU for wcn7850") changed the binding to new description
with a Power Management Unit (PMU), thus certain power-controller
properties are considered deprecated and are part of that PMUs binding.
Deprecate them to mark clearly that new PMU-based approach is preferred.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
One big Qualcomm Bluetooth schema is hardly manageable: it lists all
possible properties (19 supplies). Split qcom,wcn7850-bt to separate
bindings, so device schema will be easier to read/maintain and list only
relevant properties. Re-shuffle few properties to alphabetical order
while moving them and drop redundant enable-gpios description.
This makes the source qualcomm-bluetooth.yaml binding empty, thus drop
it making entire change a variant of file rename.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 5f4f954bba ("dt-bindings: bluetooth: bring the HW description
closer to reality for wcn6855") changed the binding to new description
with a Power Management Unit (PMU), thus certain power-controller
properties are considered deprecated and are part of that PMUs binding.
Deprecate them to mark clearly that new PMU-based approach is preferred.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
One big Qualcomm Bluetooth schema is hardly manageable: it lists all
possible properties (19 supplies). Split qcom,wcn6855-bt to separate
bindings, so device schema will be easier to read/maintain and list only
relevant properties.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit cca4fe3497 ("dt-bindings: bluetooth: Utilize PMU abstraction
for WCN6750") changed the binding to new description with a Power
Management Unit (PMU), thus certain power-controller properties are
considered deprecated and are part of that PMUs binding.
Deprecate them to mark clearly that new PMU-based approach is preferred.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
One big Qualcomm Bluetooth schema is hardly manageable: it lists all
possible properties (19 supplies). Split qcom,wcn6750-bt to separate
bindings, so device schema will be easier to read/maintain and list only
relevant properties.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
One big Qualcomm Bluetooth schema is hardly manageable: it lists all
possible properties (19 supplies). Split qcom,wcn3990-bt to separate
bindings, so device schema will be easier to read/maintain and list only
relevant properties.
This binding is very similar to qcom,wcn3950-bt, however devices have
additional VDD_CH1 supply.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
One big Qualcomm Bluetooth schema is hardly manageable: it lists all
possible properties (19 supplies). Split qcom,wcn3950-bt to separate
bindings, so device schema will be easier to read/maintain and list only
relevant properties.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
of_pci_bus_find_domain_nr() allows its parent parameter to be NULL but
of_pci_bus_release_domain_nr() (that undoes its effect) doesn't -- that
means it's going to blow up while calling of_get_pci_domain_nr() if the
parent parameter indeed happens to be NULL. Add the missing NULL check.
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: c14f7ccc9f ("PCI: Assign PCI domain IDs by ida_alloc()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@auroraos.dev>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260127203944.28588-1-s.shtylyov@auroraos.dev
