[ Upstream commit 934e9d137d ]
Fix a kernel oops found while testing the stm32_pcie Endpoint driver
with handling of PERST# deassertion:
During EP initialization, pci_epf_test_alloc_space() allocates all BARs,
which are further freed if epc_set_bar() fails (for instance, due to no
free inbound window).
However, when pci_epc_set_bar() fails, the error path:
pci_epc_set_bar() ->
pci_epf_free_space()
does not clear the previous assignment to epf_test->reg[bar].
Then, if the host reboots, the PERST# deassertion restarts the BAR
allocation sequence with the same allocation failure (no free inbound
window), creating a double free situation since epf_test->reg[bar] was
deallocated and is still non-NULL.
Thus, make sure that pci_epf_alloc_space() and pci_epf_free_space()
invocations are symmetric, and as such, set epf_test->reg[bar] to NULL
when memory is freed.
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
Link: https://lore.kernel.org/r/20250124123043.96112-1-christian.bruel@foss.st.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c03f9f4d3 ]
The boot status in the watchdog device struct is updated during
controller probe stage. Application layer can get the boot status
through the command, cat /sys/class/watchdog/watchdogX/bootstatus.
The bootstatus can be,
WDIOF_CARDRESET => System is reset due to WDT timeout occurs.
Others => Other reset events, e.g., power on reset.
On ASPEED platforms, boot status is recorded in the SCU registers.
- AST2400: Only a bit is used to represent system reset triggered by
any WDT controller.
- AST2500/AST2600: System reset triggered by different WDT controllers
can be distinguished by different SCU bits.
Besides, on AST2400 and AST2500, since alternating boot event is
also triggered by using WDT timeout mechanism, it is classified
as WDIOF_CARDRESET.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20250113093737.845097-2-chin-ting_kuo@aspeedtech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be4ae8c194 ]
This functionally brings tegra186 in line with tegra210 and tegra194,
sharing a cpufreq policy between all cores in a cluster.
Reviewed-by: Sumit Gupta <sumitg@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Aaron Kling <webgeek1234@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b80c0abe4 ]
In coresight-etb10 drivers, etb_drvdata->spinlock can be held
during __schedule() by perf_event_task_sched_out()/in().
Since etb_drvdata->spinlock type is spinlock_t and
perf_event_task_sched_out()/in() is called after acquiring rq_lock,
which is raw_spinlock_t (an unsleepable lock),
this poses an issue in PREEMPT_RT kernel where spinlock_t is sleepable.
To address this, change type etb_drvdata->spinlock in coresight-etb10 drivers,
which can be called by perf_event_task_sched_out()/in(),
from spinlock_t to raw_spinlock_t.
Reviewed-by: James Clark <james.clark@linaro.org>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250306121110.1647948-6-yeoreum.yun@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e76336e14 ]
In _badblocks_check(), there are lines of code like this,
1246 sectors -= len;
[snipped]
1251 WARN_ON(sectors < 0);
The WARN_ON() at line 1257 doesn't make sense because sectors is
unsigned long long type and never to be <0.
Fix it by checking directly checking whether sectors is less than len.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Coly Li <colyli@kernel.org>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20250309160556.42854-1-colyli@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89be3c15a5 ]
Setting format to s16le is required for compressed playback on compatible
soundcards.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20250228161430.373961-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09965a1420 ]
Commit 2545c1c948 ("auxdisplay: Move hwidth and bwidth to struct
hd44780_common") makes charlcd_alloc() argument-less effectively dropping
the single allocation for the struct charlcd_priv object along with
the driver specific one. Restore that behaviour here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d838605fea ]
In run_queue(), check if the queue of pending requests is empty instead
of blindly assuming that it won't be.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d9cabc8f5 ]
[Why]
When switching between PSR/Replay,
the DPCD config of previous mode is not cleared,
resulting in unexpected behavior in TCON.
[How]
Initialize the DPCD in setup function
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Leon Huang <Leon.Huang1@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a21da2842 ]
[WHY]
DP tunneling should not abort link train even bandwidth become
too low after downgrade. Otherwise, it would fail compliance test.
[HOW}
Do link train with downgrade settings even bandwidth is not enough
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3069feecd ]
[WHY]
In some cases the remain de-tile buffer segments will be greater
than zero if we don't add the non-top pipe to calculate, at
this time the override de-tile buffer size will be valid and used.
But it makes the de-tile buffer segments used finally for all of pipes
exceed the maximum.
[HOW]
Add the non-top pipe to calculate the remain de-tile buffer segments.
Don't set override size to use the average according to pipe count
if the value exceed the maximum.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 756e58e83e ]
[why & how]
1. apply oem panel timing (not only on OLED)
2. remove MIN_DPP_DISP_CLK request in driver.
This fix will apply for dcn31x but not
sync with DML's output.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a18dfa9925 ]
When spanning datagram construction over multiple send calls using
MSG_MORE, per datagram settings are configured on the first send.
That is when ip(6)_setup_cork stores these settings for subsequent use
in __ip(6)_append_data and others.
The only flag that escaped this was dontfrag. As a result, a datagram
could be constructed with df=0 on the first sendmsg, but df=1 on a
next. Which is what cmsg_ip.sh does in an upcoming MSG_MORE test in
the "diff" scenario.
Changing datagram conditions in the middle of constructing an skb
makes this already complex code path even more convoluted. It is here
unintentional. Bring this flag in line with expected sockopt/cmsg
behavior.
And stop passing ipc6 to __ip6_append_data, to avoid such issues
in the future. This is already the case for __ip_append_data.
inet6_cork had a 6 byte hole, so the 1B flag has no impact.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250307033620.411611-3-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf4bd16088 ]
Some regulatory bodies doesn't allow IR (initiate radioation) on a
specific subband, but allows it for channels with a bandwidth of 20 MHz.
Add a channel flag that indicates that, and consider it in
cfg80211_reg_check_beaconing.
While on it, fix the kernel doc of enum nl80211_reg_rule_flags and
change it to use BIT().
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Co-developed-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Signed-off-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.d3ab352a73ff.I8a8f79e1c9eb74936929463960ee2a324712fe51@changeid
[fix typo]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65bff0be9b ]
Do address translations only between shared links. It is
possible that while an non-AP MLD station and an AP MLD
station have shared links, the frame is intended to be sent
on a link which is not shared (for example when sending a
probe response).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.1aa461270bb6.Ic21592e1b1634653f02b80628cb2152f6e9de367@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e104aa367 ]
If multi-link reconfiguration fails, we can disconnect with a local link
already allocated but the BSS entry not assigned yet, which leads to a
warning in cfg80211. Add a check to avoid the warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.699bd9cbabe5.I599d5ff69092a65e916e2acd25137ae9df8debe8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ea2970b05 ]
This UEFI variable name was badly named. Fix its name and also use the
right GUID to find it: we need to use the BT_WIFI (a.k.a. Common) GUID.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231426.78c998d0fa71.I2bc9d72c1dc2c4d7028f0265634a940c2fadbbb5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f0ab2f35a ]
This is a discrete device, don't mark it as integrated.
This also means we cannot set the LTR delay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.9bb69393fcc9.I197129383e5441c8139cbb0e810ae0b71198a37c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb29b4ffaf ]
The order of actions taken for debug was implemented incorrectly.
Now we implemented the dump split and do the FW reset only in the
middle of the dump (rather than the FW killing itself on error.)
As a result, some of the actions taken when applying the config
will now crash the device, so we need to fix the order.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.6de7fa8e63ed.I40632c48e2a67a8aca05def572a934b88ce7934b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2e709805c ]
The FW is now responsible of determining the SMPS mode.
If the user disabled power save in a certain vif, we send the vif-level
power command to clear out the POWER_FLAGS_POWER_MANAGEMENT_ENA_MSK bit
for that vif.
But erroneously, the FW checks DEVICE_POWER_FLAGS_POWER_SAVE_ENA_MSK in
the device-level command to determine the SMPS mode.
To W/A this, send also the device-level command when the power save of a
vif changes, and disable power save if there is any vif that has power
save disabled.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.7bf205efa027.I2c793ff1fc2a6779a95faaee1ded348100fd97f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7f50d0433 ]
iwl_trans_reclaim is warning if it is called when the FW is not alive.
But if it is called when there is a pending restart, i.e. after a FW
error, there is no need to warn, instead - return silently.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.ba3d90b22c25.I9332506af1997faefcf0bdb51d98d5e874051722@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72c96a2dac ]
The commit 9e70a5e109 ("printk: Add per-console suspended state")
introduced the CON_SUSPENDED flag for consoles. The suspended consoles
will stop receiving messages, so don't unblank suspended consoles
because it won't be showing anything either way.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20250226-printk-renaming-v1-5-0b878577f2e6@suse.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3832862eb9 ]
At the moment, if of_iommu_configure() allocates dev->iommu itself via
iommu_fwspec_init(), then suffers a DT parsing failure, it cleans up the
fwspec but leaves the empty dev_iommu hanging around. So far this is
benign (if a tiny bit wasteful), but we'd like to be able to reason
about dev->iommu having a consistent and unambiguous lifecycle. Thus
make sure that the of_iommu cleanup undoes precisely whatever it did.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/d219663a3f23001f23d520a883ac622d70b4e642.1740753261.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbcfcb239b ]
Some Alienware laptops that support the SMM interface, may have up to 4
fans.
Tested on an Alienware x15 r1.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://lore.kernel.org/r/20250304055249.51940-2-kuurtb@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ad61970ac ]
When running secured ranging and the initiator is associated with
the responder, the TK was not set in the range request command.
Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.603dc31579d9.Icd19d797e56483c08dd22c55b96fee481c4d2f3d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfc88357b6 ]
When the device stalls an endpoint, current TD is assigned -EPIPE
status and Reset Endpoint is queued. If a Stop Endpoint is pending
at the time, it will run before Reset Endpoint and fail due to the
stall. Its handler will change TD's status to -EPROTO before Reset
Endpoint handler runs and initiates giveback.
Check if the stall has already been handled and don't try to do it
again. Since xhci_handle_halted_endpoint() performs this check too,
not overwriting td->status is the only difference.
I haven't seen this case yet, but I have seen a related one where
the xHC has already executed Reset Endpoint, EP Context state is
now Stopped and EP_HALTED is set. If the xHC took a bit longer to
execute Reset Endpoint, said case would become this one.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250311154551.4035726-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb3bbc46c9 ]
Per the SD Host Controller Simplified Specification v4.20 §3.2.3, change
the SD card clock parameters only after first disabling the external card
clock. Doing this fixes a spurious clock pulse on Baytrail and Apollo Lake
SD controllers which otherwise breaks voltage switching with a specific
Swissbit SD card.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: Erick Shepherd <erick.shepherd@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250211214645.469279-1-erick.shepherd@ni.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cbe799ac1 ]
Add support for Exynos7870 DW MMC controllers, for both SMU and non-SMU
variants. These controllers require a quirk to access 64-bit FIFO in 32-bit
accesses (DW_MMC_QUIRK_FIFO64_32).
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Link: https://lore.kernel.org/r/20250219-exynos7870-mmc-v2-3-b4255a3e39ed@disroot.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfb1d2b902 ]
pud_bad() is currently defined in terms of pud_table(). Although for some
configs, pud_table() is hard-coded to true i.e. when using 64K base pages
or when page table levels are less than 3.
pud_bad() is intended to check that the pud is configured correctly. Hence
let's open-code the same check that the full version of pud_table() uses
into pud_bad(). Then it always performs the check regardless of the config.
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20250221044227.1145393-7-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1770e9098 ]
Check for pmd_table() in pmd_trans_huge() rather then just checking for the
PMD_TABLE_BIT. But ensure all present-invalid entries are handled correctly
by always setting PTE_VALID before checking with pmd_table().
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20250221044227.1145393-8-anshuman.khandual@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 969a38be43 ]
According documentation of phy_configure_opts_dp, at the configure
stage, link rates should only be verify/configure when set_rate
flag is set, the same applies to lanes and voltage.
So do it as the documentation says.
Because voltage setting depends on the lanes, link rates set
previously, so record the link rates and lanes at it's verify stage.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250312080041.524546-1-andyshrk@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 425b1c97b0 ]
GCC 15's -Wunterminated-string-initialization saw that "id" was not
including the required trailing NUL character. Instead of marking "id"
with __nonstring[1], expand the length of the string as it is used in
(debugging) format strings that expect a properly formed C string.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=117178 [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20250310222432.work.826-kees@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b6861390f ]
nf_conntrack_max and nf_conntrack_expect_max sysctls were authorized to
be written any negative value, which would then be stored in the
unsigned int variables nf_conntrack_max and nf_ct_expect_max variables.
While the do_proc_dointvec_conv function is supposed to limit writing
handled by proc_dointvec proc_handler to INT_MAX. Such a negative value
being written in an unsigned int leads to a very high value, exceeding
this limit.
Moreover, the nf_conntrack_expect_max sysctl documentation specifies the
minimum value is 1.
The proc_handlers have thus been updated to proc_dointvec_minmax in
order to specify the following write bounds :
* Bound nf_conntrack_max sysctl writings between SYSCTL_ZERO
and SYSCTL_INT_MAX.
* Bound nf_conntrack_expect_max sysctl writings between SYSCTL_ONE
and SYSCTL_INT_MAX as defined in the sysctl documentation.
With this patch applied, sysctl writes outside the defined in the bound
will thus lead to a write error :
```
sysctl -w net.netfilter.nf_conntrack_expect_max=-1
sysctl: setting key "net.netfilter.nf_conntrack_expect_max": Invalid argument
```
Signed-off-by: Nicolas Bouchinet <nicolas.bouchinet@ssi.gouv.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9b56f219a ]
Some of 11ax AP set the UL HE-SIG-A2 reserved subfield to all 0s, which
will cause the 11be chip to recognize trigger frame as EHT. We propose
a method to bypass the "UL HE-SIG-A2 reserved subfield" and always uses
HE TB in response to the AP's trigger frame.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-6-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a52067c24c ]
This reverts commit f590308536 ("timer debug: Hide kernel addresses via
%pK in /proc/timer_list")
The timer list helper SEQ_printf() uses either the real seq_printf() for
procfs output or vprintk() to print to the kernel log, when invoked from
SysRq-q. It uses %pK for printing pointers.
In the past %pK was prefered over %p as it would not leak raw pointer
values into the kernel log. Since commit ad67b74d24 ("printk: hash
addresses printed with %p") the regular %p has been improved to avoid this
issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch to the regular pointer formatting which is safer, easier to reason
about and sufficient here.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/lkml/20250113171731-dc10e3c1-da64-4af0-b767-7c7070468023@linutronix.de/
Link: https://lore.kernel.org/all/20250311-restricted-pointers-timer-v1-1-6626b91e54ab@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05fd00e5e7 ]
Add PRP specific function for handling duplicate
packets. This is needed because of potential
L2 802.1p prioritization done by network switches.
The L2 prioritization can re-order the PRP packets
from a node causing the existing implementation to
discard the frame(s) that have been received 'late'
because the sequence number is before the previous
received packet. This can happen if the node is
sending multiple frames back-to-back with different
priority.
Signed-off-by: Jaakko Karrenpalo <jkarrenpalo@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250307161700.1045-1-jkarrenpalo@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 247e84f66a ]
All Rockchip GMAC variants typically write to GRF regs to control e.g.
interface mode, speed and MAC rx/tx delay. Newer SoCs such as RK3576 and
RK3588 use a mix of GRF and peripheral GRF regs. These syscon regmaps is
located with help of a rockchip,grf and rockchip,php-grf phandle.
However, validating the rockchip,grf and rockchip,php-grf syscon regmap
is deferred until e.g. interface mode or speed is configured, inside the
individual SoC specific operations.
Change to validate the rockchip,grf and rockchip,php-grf syscon regmap
at probe time to simplify all SoC specific operations.
This should not introduce any backward compatibility issues as all
GMAC nodes have been added together with a rockchip,grf phandle (and
rockchip,php-grf where required) in their initial commit.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250308213720.2517944-3-jonas@kwiboo.se
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2389c6efd3 ]
Frederic pointed out that the memory operations to initialize the timer are
not guaranteed to be visible, when __lock_timer() observes timer::it_signal
valid under timer::it_lock:
T0 T1
--------- -----------
do_timer_create()
// A
new_timer->.... = ....
spin_lock(current->sighand)
// B
WRITE_ONCE(new_timer->it_signal, current->signal)
spin_unlock(current->sighand)
sys_timer_*()
t = __lock_timer()
spin_lock(&timr->it_lock)
// observes B
if (timr->it_signal == current->signal)
return timr;
if (!t)
return;
// Is not guaranteed to observe A
Protect the write of timer::it_signal, which makes the timer valid, with
timer::it_lock as well. This guarantees that T1 must observe the
initialization A completely, when it observes the valid signal pointer
under timer::it_lock. sighand::siglock must still be taken to protect the
signal::posix_timers list.
Reported-by: Frederic Weisbecker <frederic@kernel.org>
Suggested-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/all/20250308155623.507944489@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f2909c6cd ]
With a large number of POSIX timers the search for a valid ID might cause a
soft lockup on PREEMPT_NONE/VOLUNTARY kernels.
Add cond_resched() to the loop to prevent that.
[ tglx: Split out from Eric's series ]
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/all/20250214135911.2037402-2-edumazet@google.com
Link: https://lore.kernel.org/all/20250308155623.635612865@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81f8f7454a ]
Currently, the IB uverbs API calls uobj_get_uobj_read(), which in turn
uses the rdma_lookup_get_uobject() helper to retrieve user objects.
In case of failure, uobj_get_uobj_read() returns NULL, overriding the
error code from rdma_lookup_get_uobject(). The IB uverbs API then
translates this NULL to -EINVAL, masking the actual error and
complicating debugging. For example, applications calling ibv_modify_qp
that fails with EBUSY when retrieving the QP uobject will see the
overridden error code EINVAL instead, masking the actual error.
Furthermore, based on rdma-core commit:
"2a22f1ced5f3 ("Merge pull request #1568 from jakemoroni/master")"
Kernel's IB uverbs return values are either ignored and passed on as is
to application or overridden with other errnos in a few cases.
Thus, to improve error reporting and debuggability, propagate the
original error from rdma_lookup_get_uobject() instead of replacing it
with EINVAL.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Link: https://patch.msgid.link/64f9d3711b183984e939962c2f83383904f97dfb.1740577869.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e856f93e0f ]
When dioread_nolock is turned on (the default), it will convert unwritten
extents to written at ext4_end_io_end(), even if the data writeback fails.
It leads to the possibility that stale data may be exposed when the
physical block corresponding to the file data is read-only (i.e., writes
return -EIO, but reads are normal).
Therefore a new ext4_io_end->flags EXT4_IO_END_FAILED is added, which
indicates that some bio write-back failed in the current ext4_io_end.
When this flag is set, the unwritten to written conversion is no longer
performed. Users can read the data normally until the caches are dropped,
after that, the failed extents can only be read to all 0.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20250122110533.4116662-3-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26343ca0df ]
data_err=abort aborts the journal on I/O errors. However, this option is
meaningless if journal is disabled, so it is rejected in nojournal mode
to reduce unnecessary checks. Also, this option is ignored upon remount.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250122110533.4116662-4-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdbbc480f4 ]
On the QCM6490 boards, the LPASS firmware controls the complete clock
controller functionalities and associated power domains. However, only
the LPASS resets required to be controlled by the high level OS. Thus,
add support for the resets in the clock driver to enable the Audio SW
driver to assert/deassert the audio resets as needed.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20250221-lpass_qcm6490_resets-v5-2-6be0c0949a83@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a149377c03 ]
Add support for GPIO headphone detection with the hp-det-gpios
property. In order for this to properly disable the path upon
removal of headphones, the output must be labelled Headphone which
is a common sink in the driver.
Describe a headphone jack and detection GPIO in the driver, check for
a corresponding device tree node, and enable jack detection in a new
machine init function if described.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Ryan Walklin <ryan@testtoast.com>
--
Changelog v1..v2:
- Separate DAPM changes into separate patch and add rationale.
Tested-by: Philippe Simons <simons.philippe@gmail.com>
Link: https://patch.msgid.link/20250214220247.10810-4-ryan@testtoast.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19478f2011 ]
There have been multiple fixes to the video caps that are missing for
SRIOV. Update the SRIOV caps with correct values.
Signed-off-by: David Rosca <david.rosca@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ruijing Dong <ruijing.dong@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e27b36ea6b ]
Just use the default values. There's not need to
get the value from hardware and it could cause problems
if we do that at runtime and gfxoff is active.
Reviewed-by: Mukul Joshi <mukul.joshi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc3c139cf0 ]
Just use the default values. There's not need to
get the value from hardware and it could cause problems
if we do that at runtime and gfxoff is active.
Reviewed-by: Mukul Joshi <mukul.joshi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76b58d5111 ]
The chipid macro/variable and regmap_read function call is not needed
because the TPS65219_REG_TI_DEV_ID register value is not a consistent value
across TPS65219 PMIC config versions. Reading from the DEV_ID register
without a consistent value to compare it to isn't useful. There isn't a
way to verify the match data ID is the same ID read from the DEV_ID device
register. 0xF0 isn't a DEV_ID value consistent across TPS65219 NVM
configurations.
For TPS65215, there is a consistent value in bits 5-0 of the DEV_ID
register. However, there are other error checks in place within probe()
that apply to both PMICs rather than keeping this isolated check for one
PMIC.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://lore.kernel.org/r/20250206173725.386720-4-s-ramamoorthy@ti.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12bfa0fee ]
Each pin can be configured as a Special Function IO (SFIO) or GPIO,
where the SFIO enables the pin to operate in alternative modes such as
I2C, SPI, etc.
The current implementation sets all the pins back to SFIO mode
even if they were initially in GPIO mode. This can cause glitches
on the pins when pinctrl_gpio_free() is called.
Avoid these undesired glitches by storing the pin's SFIO/GPIO
state on GPIO request and restoring it on GPIO free.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Link: https://lore.kernel.org/20250305104939.15168-2-pshete@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
