Add a driver for transparent busses that don't need a real driver, but
where the bus controller is part of a PM domain, or under the control of
a functional clock. Typically, the bus controller's PM domain and/or
clock must be enabled for child devices connected to the bus (either
on-SoC or externally) to function.
Hence the sole purpose of this driver is to enable its clock and PM
domain (if exist(s)), which are specified in the DT and managed from
platform and PM domain code, and to probe for child devices.
Due to the child-parent relationship with devices connected to the bus,
PM domain and clock state transitions are handled in the correct order.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The bindings for the BSC extend the bindings for "simple-pm-bus".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7790 device tree.
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7791 device tree.
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Henninger board dependent part of the CAN0 device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7791 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7790 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Configure the pinmux on kzm9d to use the serial connector for uart1.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With this information all GPIOs can make use of the PFC functionality.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Documentation says the last register is at 0x184 (CAxCPUCMCR), so use
proper length. Current APMU code accesses CAxCPUnCR which is currently
outside of the remapped area.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Documentation says the last register is at 0x184 (CAxCPUCMCR), so use
proper length. Current APMU code accesses CAxCPUnCR which is currently
outside of the remapped area.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector
and configure the DISP pin group that drives the HDMI transmitter DE
pin.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
Fixes: 59e79895b9 ("ARM: shmobile: r8a7791: Add clocks")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
* Correct base address of SD3 div6 clk.
* Update div6 clock node labels
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
This has no run-time affect as the clock nodes are not currently used.
Fixes: 8e181633e6 ("ARM: shmobile: r8a7794: Add SDHI clocks to device tree")
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the ethernet controller for the Alt board. Pin muxing entries are
currently left out as r8a7794 pin control support isn't available yet.
We thus rely on the boot loader to configure ethernet pins for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7794 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the seven IPMMU instances found in the r8a7791 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7790 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two system DMA controllers in the r8a7794 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, the first 16 MiB of RAM was reserved for the RT
processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.
As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.
While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, the first 16 MiB of RAM was reserved for the RT
processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.
As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.
While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specifies clock sources and register bits.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[geert: Drop renesas,src-shift/renesas,src-width, pad to 4 or 8 parents]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the R2025D real-time clock, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the ADXL345 three-axis digital accelerometer sensor,
which is connected to i2c0.
As trivial i2c devices are matched against the first compatible entry
only, compatibility is declared with "adi,adxl34x" only for now.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device needs an interrupt to operate properly. Specify the two
interrupts used on the board.
While at it rename the DT node to accelerometer@1d to describe the
device's function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the AK8975 magnetometer sensor, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Specify the device interrupt to avoid polling for end of conversion.
While at it rename the DT node to compass@c to describe the device's
function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While at it rename the ak4648 node to "codec" to describe the device's
function instead of its model, and move its device-specific property
after its generic properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The sh73a0 INTC can't mask interrupts properly most likely due to a
hardware bug. Set the control-parent property to delegate masking to the
parent interrupt controller.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds the remaining DIV6 clocks and all possible parents for the SUB
clock.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This has been broken for a long time: it broke first in 2.6.35, then was
almost fixed in 2.6.36 but this one-liner slipped through the cracks.
The bug shows up as an infinite loop in Windows 7 (and newer) boot on
32-bit hosts without EPT.
Windows uses CMPXCHG8B to write to page tables, which causes a
page fault if running without EPT; the emulator is then called from
kvm_mmu_page_fault. The loop then happens if the higher 4 bytes are
not 0; the common case for this is that the NX bit (bit 63) is 1.
Fixes: 6550e1f165
Fixes: 16518d5ada
Cc: stable@vger.kernel.org # 2.6.35+
Reported-by: Erik Rull <erik.rull@rdsoftware.de>
Tested-by: Erik Rull <erik.rull@rdsoftware.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'apic' is not defined if !CONFIG_X86_64 && !CONFIG_X86_LOCAL_APIC.
Posted interrupt makes no sense without CONFIG_SMP, and
CONFIG_X86_LOCAL_APIC will be set with it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch extends trace_kvm_exit() to include KVM exit reasons
(i.e. EC of HSR). The tracing function then dumps both exit reason
and PC of vCPU, shown as the following. Tracing tools can use this
new exit_reason field to better understand the behavior of guest VMs.
886.301252: kvm_exit: HSR_EC: 0x0024, PC: 0xfffffe0000506b28
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The check is supposed to catch page-unaligned sizes, not the inverse.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
commit 0e707ae79b ("UBI: do propagate positive error codes up") seems
to have produced an unintended change in the control flow here.
Completely untested, but it looks obvious.
Caught by Coverity, which didn't like the indentation. CID 1271184.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Current FW is declaring support for BFER in ucode_capa.capa
but it doesn't really support it unless the new LQ_SS_PARAMS API
is supported as well. Avoid publishing BFER in our VHT caps
if FW doesn't support.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwl_mvm_stop_roc removes TE only if running flag is set. This is not correct
since this flag is only set when the TE is started.
This resulted in a TE not being removed, when mac80211 believes that there are
no active ROCs.
Fixes: bf5da87f60 ("iwlwifi: mvm: add remove flow for AUX ROC time events")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
During a queue overflow condition while we are waiting for auditd to drain the
queue to make room for regular messages, we don't want a successful auditd that
has bypassed the queue check to reset the backlog wait time.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Copy the set wait time to a working value to avoid losing the set
value if the queue overflows.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>