Add QCS615-specific configuration for USB/DP PHY, including DP init
routines, voltage swing tables, and platform data. Add compatible
"qcs615-qmp-usb3-dp-phy".
Note: SW_PORTSELECT handling for orientation flip is not implemented
due to QCS615 fixed-orientation design and non-standard lane mapping.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-12-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When both USB and DP PHY modes are enabled simultaneously on the same
QMP USBC PHY, it can lead to hardware misconfiguration and undefined
behavior. This happens because the PHY resources are not designed to
operate in both modes at the same time.
To prevent this, introduce a mutual exclusion check between USB and DP
PHY modes.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-10-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current implementation programs USB-specific registers in
qmp_usbc_com_init(), which is shared by both USB and DP modes. This
causes unnecessary configuration when the PHY is used for DP.
Move USB-only register setup from com_init to qmp_usbc_usb_power_on,
so it runs only for USB mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-7-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
USB3DP PHY requires link and vco_div clocks when operating in DP mode.
Extend qmp_usbc_register_clocks and the clock provider logic to register
these clocks along with the existing pipe clock, to support both USB and
DP configurations.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-6-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The original reset list only works for USB-only PHYs. USB3DP PHYs require
different reset names such as "dp_phy", so they need a separate list.
Moving reset configuration into qmp_phy_cfg allows per-PHY customization
without adding special-case logic in DT parsing. The legacy DT path keeps
using the old hardcoded list, while non-legacy paths use cfg->reset_list.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-5-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
QMP USBC PHY drivers previously did not set init_load_uA for regulators,
which could result in incorrect vote levels. This patch introduces
regulator definitions with proper init_load_uA values based on each
chip's power grid design.
QCS615 USB3 PHY was previously reusing qcm2290_usb3phy_cfg, but its
regulator requirements differ. A new qcs615_usb3phy_cfg is added to
reflect the correct settings.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-4-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Extend qmp_usbc_offsets and qmp_phy_cfg with DP-specific fields,
including register offsets, init tables, and callback hooks. Also
update qmp_usbc struct to track DP-related resources and state.
This enables support for USB/DP switchable Type-C PHYs that operate
in either mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-3-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To support following DisplayPort (DP) mode over the Type-C PHY, rename
USB-specific functions and ops to clearly separate them from common or
DP-related logic.
This is a preparatory cleanup to enable USB + DP dual mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-2-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add device tree binding documentation for the Qualcomm QMP USB3+DP PHY
on QCS615 Platform. This PHY supports both USB3 and DP functionality
over USB-C, with PHY mode switching capability. It does not support
combo mode.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Xiangxu Yin <xiangxu.yin@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215-add-displayport-support-for-qcs615-platform-v8-1-cbc72c88a44e@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the TI TCAN1046 automotive CAN transceiver. The TCAN1046 is a
dual high-speed CAN transceiver with sleep-mode support and no EN pin,
mirroring the behaviour of the NXP TJA1048, which also provides dual
channels and STB1/2 sleep-control lines.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251209162119.2038313-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Set the regulator load before enabling the regulators to ensure stable
operation and proper power management on platforms where regulators are
shared between the QMP USB PHY and other IP blocks.
Introduce a regulator data structure with explicit enable load values and
use the regulator framework's `init_load_uA` field along with
`devm_regulator_bulk_get_const()` to ensure that `regulator_set_load()` is
applied automatically before the first enable, providing consistent power
management behavior across platforms.
Signed-off-by: Faisal Hassan <faisal.hassan@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20250905101243.14815-1-faisal.hassan@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add QMP PCIe PHY support for the Kaanapali platform.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-5-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some qserdes-com register offsets for the v8 PHY were previously omitted,
as they were not needed by earlier v8 PHY initialization sequences. Add
these missing v8 register offsets now required to support PCIe QMP PHY on
Kaanapali platform.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-4-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Kaanapali SoC uses QMP phy with version v8 for PCIe Gen3 x2. Add the new
PCS PCIE specific offsets in a dedicated header file.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-3-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Kaanapali SoC uses QMP PHY with version v8 for PCIe Gen3 x2, but requires
a completely unique qserdes-txrx register offsets compared to existing v8
offsets.
Hence, add a dedicated header file containing the FULL SET of qserdes-txrx
register definitions required for Kaanapali's PCIe PHY operation.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251124-kaanapali-pcie-phy-v4-2-d04ee9cca83b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Introduce a driver that supports three PHYs found on the SpacemiT
K1 SoC. The first PHY is a combo PHY that can be configured for
use for either USB 3 or PCIe. The other two PHYs support PCIe
only.
All three PHYs must be programmed with an 8 bit receiver termination
value, which must be determined dynamically. Only the combo PHY is
able to determine this value. The combo PHY performs a special
calibration step at probe time to discover this, and that value is
used to program each PHY that operates in PCIe mode. The combo
PHY must therefore be probed before either of the PCIe-only PHYs
will be used.
Each PHY has an internal PLL driven from an external oscillator.
This PLL started when the PHY is first initialized, and stays
on thereafter.
During normal operation, the USB or PCIe driver using the PHY must
ensure (other) clocks and resets are set up properly.
However PCIe mode clocks are enabled and resets are de-asserted
temporarily by this driver to perform the calibration step on the
combo PHY.
Tested-by: Junzhong Pan <panjunzhong@linux.spacemit.com>
Signed-off-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/ba532f8d-a452-40e5-af46-b58b89f70a92@linaro.org/ [1]
Tested-by: Yixun Lan <dlan@gentoo.org>
Link: https://patch.msgid.link/20251218151235.454997-4-elder@riscstar.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the Device Tree binding for the PCIe/USB 3.0 combo PHY found in
the SpacemiT K1 SoC. This is one of three PCIe PHYs, and is unusual
in that only the combo PHY can perform a calibration step needed to
determine settings used by the other two PCIe PHYs.
Calibration must be done with the combo PHY in PCIe mode, and to allow
this to occur independent of the eventual use for the PHY (PCIe or USB)
some PCIe-related properties must be supplied: clocks; resets; and a
syscon phandle.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Alex Elder <elder@riscstar.com>
Link: https://lore.kernel.org/all/ba532f8d-a452-40e5-af46-b58b89f70a92@linaro.org/ [1]
Tested-by: Yixun Lan <dlan@gentoo.org>
Link: https://patch.msgid.link/20251218151235.454997-2-elder@riscstar.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
MT8195's HDMI PHY block has 4 clocks instead of just a single one.
Describe the extra clocks for it.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
[Louis-Alexis Eyraud: addressed feedback from mailing list]
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20251217-mtk-genio-evk-hdmi-support-v2-3-a994976bb39a@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add compatible string for the HDMI PHY IP on MT8188 SoC, that is
compatible with the one found on MT8195 SoC.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20251217-mtk-genio-evk-hdmi-support-v2-2-a994976bb39a@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For all of the HDMI PHYs compatible with the one found on MT8195
the output clock has a different datasheet name and specifically
it is called "hdmi_txpll", differently from the older HDMI PHYs
which output block is called "hdmitx_dig_cts".
Replace clock output name string check by max item number one to allow
the new name on all of the HDMI PHY IPs that are perfectly compatible
with MT8195.
[Louis-Alexis Eyraud: split patch, addressed previous feedback from
mailing list, and reworded description]
Fixes: c78fe548b0 ("dt-bindings: phy: mediatek: hdmi-phy: Add mt8195 compatible")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Link: https://patch.msgid.link/20251217-mtk-genio-evk-hdmi-support-v2-1-a994976bb39a@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop a bunch of unused members from struct ropll_config and make the
static ropll_tmds_cfg table more readable:
* add a table header
* sort rows by rate
* convert hex values to decimal (for consistency)
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251221-phy-hdptx-pll-fix-v2-2-ae4abf7f75a1@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Attempting to make use of a 1080p@120Hz display mode with 10 bpc RGB on
my Acer XV275K P3 monitor results in a blank image. A similar behavior
has been reported on Philips 279M1RV.
The faulty modeline is created by drm_gtf_mode_complex() based on the
following EDID entry from the Standard Timings block:
GTF: 1920x1080 119.999987 Hz 16:9 138.840 kHz 368.759000 MHz
It's worth noting the computed pixel clock ends up being slightly higher
at 368.881000 MHz. Nevertheless, this seems to work consistently fine
with 8 bpc RGB.
After switching to 10 bpc, the TMDS character rate expected for the mode
increases to 461.101250 MHz, as per drm_hdmi_compute_mode_clock().
Since there is no entry for this rate in the ropll_tmds_cfg table, the
necessary HDMI PLL configuration parameters are calculated dynamically
by rk_hdptx_phy_clk_pll_calc(). However, the resulting output rate is
not quite a perfect match, i.e. 461.100000 MHz. That proved to be the
actual root cause of the problem.
Add a new entry to the TMDS configuration table and provide the
necessary frequency division coefficients for the PHY PLL to generate
the expected 461.101250 MHz output.
Fixes: 9d0ec51d7c ("phy: rockchip: samsung-hdptx: Add high color depth management")
Tested-by: Derek Foreman <derek.foreman@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251221-phy-hdptx-pll-fix-v2-1-ae4abf7f75a1@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to IC engineer suggestion, set ssc_range as -4003 ppm
will have more tolerance for EMI, and suitable for more boards.
Besides, it's confirmed that with this setting the TX SSC test
will pass on one customer board.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251219081354.3806806-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY core defines phy_pm_runtime_put() to return an int, but that
return value is never used. It also passes the return value of
pm_runtime_put() to the caller which is not very useful.
Returning an error code from pm_runtime_put() merely means that it has
not queued up a work item to check whether or not the device can be
suspended and there are many perfectly valid situations in which that
can happen, like after writing "on" to the devices' runtime PM "control"
attribute in sysfs for one example.
Modify phy_pm_runtime_put() to discard the pm_runtime_put() return
value and change its return type to void. Also drop the redundant
pm_runtime_enabled() call from there.
No intentional functional impact.
This will facilitate a planned change of the pm_runtime_put() return
type to void in the future.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2556645.jE0xQCEvom@rafael.j.wysocki
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Passing pm_runtime_put() return value to the callers is not particularly
useful.
Returning an error code from pm_runtime_put() merely means that it has
not queued up a work item to check whether or not the device can be
suspended and there are many perfectly valid situations in which that
can happen, like after writing "on" to the devices' runtime PM "control"
attribute in sysfs for one example. It also happens when the kernel is
configured with CONFIG_PM unset.
Accordingly, update samsung_mipi_dcphy_exit() to simply discard the
return value of pm_runtime_put() and always return success to the
caller.
This will facilitate a planned change of the pm_runtime_put() return
type to void in the future.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2281919.Icojqenx9y@rafael.j.wysocki
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Printing error messages on pm_runtime_put() returning negative values
is not particularly useful.
Returning an error code from pm_runtime_put() merely means that it has
not queued up a work item to check whether or not the device can be
suspended and there are many perfectly valid situations in which that
can happen, like after writing "on" to the devices' runtime PM "control"
attribute in sysfs for one example.
Accordingly, update mixel_lvds_phy_reset() to simply discard the return
value of pm_runtime_put().
This will facilitate a planned change of the pm_runtime_put() return
type to void in the future.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2012926.taCxCBeP46@rafael.j.wysocki
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add compatibles for the USB3.0 PHY used in the RZ/V2H(P) and RZ/V2N SoCs.
These SoCs integrate the same USB3 PHY IP block as the RZ/G3E, so the
RZ/G3E compatible is used as a fallback for both.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://patch.msgid.link/20251222161846.152952-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the OTG USB port is used to power to SoC, configured as peripheral and
used in gadget mode, communication stops without notice about 6 seconds
after the gadget is configured and enumerated.
The problem was observed on a Radxa Rock Pi S board, which can only be
powered by the only USB-C connector. That connector is the only one usable
in gadget mode. This implies the USB cable is connected from before boot
and never disconnects while the kernel runs.
The related code flow in the PHY driver code can be summarized as:
* the first time chg_detect_work starts (6 seconds after gadget is
configured and enumerated)
-> rockchip_chg_detect_work():
if chg_state is UNDEFINED:
property_enable(base, &rphy->phy_cfg->chg_det.opmode, false); [Y]
* rockchip_chg_detect_work() changes state and re-triggers itself a few
times until it reaches the DETECTED state:
-> rockchip_chg_detect_work():
if chg_state is DETECTED:
property_enable(base, &rphy->phy_cfg->chg_det.opmode, true); [Z]
At [Y] all existing communications stop. E.g. using a CDC serial gadget,
the /dev/tty* devices are still present on both host and device, but no
data is transferred anymore. The later call with a 'true' argument at [Z]
does not restore it.
Due to the lack of documentation, what chg_det.opmode does exactly is not
clear, however by code inspection it seems reasonable that is disables
something needed to keep the communication working, and testing proves that
disabling these lines lets gadget mode keep working. So prevent changes to
chg_det.opmode when there is a cable connected (VBUS present).
Fixes: 98898f3bc8 ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/lkml/20250414185458.7767aabc@booty/
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20251127-rk3308-fix-usb-gadget-phy-disconnect-v2-2-dac8a02cd2ca@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the OTG USB port is used to power the SoC, configured as peripheral
and used in gadget mode, there is a disconnection about 6 seconds after the
gadget is configured and enumerated.
The problem was observed on a Radxa Rock Pi S board, which can only be
powered by the only USB-C connector. That connector is the only one usable
in gadget mode. This implies the USB cable is connected from before boot
and never disconnects while the kernel runs.
The problem happens because of the PHY driver code flow, summarized as:
* UDC start code (triggered via configfs at any time after boot)
-> phy_init
-> rockchip_usb2phy_init
-> schedule_delayed_work(otg_sm_work [A], 6 sec)
-> phy_power_on
-> rockchip_usb2phy_power_on
-> enable clock
-> rockchip_usb2phy_reset
* Now the gadget interface is up and running.
* 6 seconds later otg_sm_work starts [A]
-> rockchip_usb2phy_otg_sm_work():
if (B_IDLE state && VBUS present && ...):
schedule_delayed_work(&rport->chg_work [B], 0);
* immediately the chg_detect_work starts [B]
-> rockchip_chg_detect_work():
if chg_state is UNDEFINED:
if (!rport->suspended):
rockchip_usb2phy_power_off() <--- [X]
At [X], the PHY is powered off, causing a disconnection. This quickly
triggers a new connection and following re-enumeration, but any connection
that had been established during the 6 seconds is broken.
The code already checks for !rport->suspended (which, somewhat
counter-intuitively, means the PHY is powered on), so add a guard for VBUS
as well to avoid a disconnection when a cable is connected.
Fixes: 98898f3bc8 ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/lkml/20250414185458.7767aabc@booty/
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Co-developed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20251127-rk3308-fix-usb-gadget-phy-disconnect-v2-1-dac8a02cd2ca@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The mmio regmap that may be allocated during probe is never freed.
Switch to using the device managed allocator so that the regmap is
released on probe failures (e.g. probe deferral) and on driver unbind.
Fixes: 5ab90f4012 ("phy: ti: gmii-sel: Do not use syscon helper to build regmap")
Cc: stable@vger.kernel.org # 6.14
Cc: Andrew Davis <afd@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20251127134834.2030-1-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
LAN969x uses the SparX-5 SERDES driver, so make it selectable for
ARCH_LAN969X.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Gabor Juhos <j4g8y7@gmail.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251031121834.665987-1-robert.marko@sartura.hr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Likely the last PR in 2025, again a collection of lots of small fixes.
Most of them are various device-specific small fixes.
* An ASoC core fix for correcting the clamping behavior of *_SX mixer
elements
* Various fixes for ASoC fsl, SOF, etc
* Usual HD- and USB-audio quirks / fix-ups
* A couple of error-handling fixes for legacy PCMCIA drivers
-----BEGIN PGP SIGNATURE-----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=aBfc
-----END PGP SIGNATURE-----
Merge tag 'sound-6.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Likely the last pull request in 2025, again a collection of lots of
small fixes. Most of them are various device-specific small fixes:
- An ASoC core fix for correcting the clamping behavior of *_SX mixer
elements
- Various fixes for ASoC fsl, SOF, etc
- Usual HD- and USB-audio quirks / fix-ups
- A couple of error-handling fixes for legacy PCMCIA drivers"
* tag 'sound-6.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (35 commits)
ALSA: hda/realtek: fix PCI SSID for one of the HP 200 G2i laptop
ASoC: ops: fix snd_soc_get_volsw for sx controls
ALSA: hda/realtek: Add Asus quirk for TAS amplifiers
ASoC: Intel: soc-acpi-intel-mtl-match: Add 6 amp CS35L63 with feedback
ASoC: Intel: soc-acpi-intel-mtl-match: Add 6 amp CS35L56 with feedback
ASoC: fsl-asoc-card: Use of_property_present() for non-boolean properties
ASoC: rt1320: update VC blind write settings
ASoC: fsl_xcvr: provide regmap names
ASoC: fsl_sai: Add missing registers to cache default
ASoC: ak4458: remove the reset operation in probe and remove
ASoC: fsl_asrc_dma: fix duplicate debugfs directory error
ASoC: fsl_easrc: fix duplicate debugfs directory error
ALSA: hda/realtek: fix micmute LED reversed on HP Abe and Bantie
ALSA: hda/realtek: Add support for HP Clipper Laptop
ALSA: hda/realtek: Add support for HP Trekker Laptop
ALSA: usb-mixer: us16x08: validate meter packet indices
ASoC: Intel: soc-acpi-intel-nvl-match: Drop rt722 l3 from the match table
ASoC: soc-acpi / SOF: Add best_effort flag to get_function_tplg_files op
ASoC: SOF: Intel: pci-mtl: Change the topology path to intel/sof-ipc4-tplg
ASoC: SOF: ipc4-topology: set playback channel mask
...
devm_pm_runtime_enable() can fail due to memory allocation. The current
code ignores its return value after calling pm_runtime_set_active(),
leaving the device in an inconsistent state if runtime PM initialization
fails.
Check the return value of devm_pm_runtime_enable() and return on
failure. Also move the declaration of 'ret' to the function scope
to support this check.
Fixes: ee8e41b504 ("phy: ti: phy-da8xx-usb: Add runtime PM support")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251124105734.1027-1-vulab@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The "index" variable is used as an index into the usbphyc->phys[] array
which has usbphyc->nphys elements. So if it is equal to usbphyc->nphys
then it is one element out of bounds. The "index" comes from the
device tree so it's data that we trust and it's unlikely to be wrong,
however it's obviously still worth fixing the bug. Change the > to >=.
Fixes: 94c358da3a ("phy: stm32: add support for STM32 USB PHY Controller (USBPHYC)")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://patch.msgid.link/aTfHcMJK1wFVnvEe@stanley.mountain
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use acpi_osc_handshake() introduced previously for implementing the
\_SB._OSC USB4 features control negotiation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/3879947.MHq7AAxBmi@rafael.j.wysocki
The feature mask creation for \_SB._OSC is messy and hard to follow,
so clean it up and make all of the CPPC-related features depend on
CONFIG_ACPI_CPPC_LIB as they will not work if it is not set anyway.
Also make acpi_bus_osc_negotiate_platform_control() print a message
including a bit mask representig the features for which control has
been granted.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/4495088.ejJDZkT8p0@rafael.j.wysocki
Both acpi_bus_osc_negotiate_platform_control() and
acpi_bus_osc_negotiate_usb_control() first call acpi_run_osc() to
evaluate _OSC in "query mode", with OSC_QUERY_ENABLE set in the
capabilities buffer, and then use the resultant feature mask as
the input buffer for requesting control of those features by
calling acpi_run_osc() to evaluate _OSC with OSC_QUERY_ENABLE clear.
This involves some code duplication and unnecessary memory
allocations, so introduce a new helper function carrying out an
_OSC handshake along the lines of the above description in a simpler
way and update acpi_bus_osc_negotiate_platform_control() to use it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/1966378.CQOukoFCf9@rafael.j.wysocki
Use ACPI_FREE() for freeing an object coming from acpi_eval_osc()
and rename the "out_free" to "out" because it does not involve
kfree() any more.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/8682086.NyiUUSuA9g@rafael.j.wysocki
Split a function for processing _OSC errors called acpi_osc_error_check()
out of acpi_run_osc() to facilitate subsequent changes.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/6135328.MhkbZ0Pkbq@rafael.j.wysocki
Split a function for evaluating _OSC called acpi_eval_osc() out of
acpi_run_osc() to facilitate subsequent changes and add some more
parameters sanity checks to the latter.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/22963770.EfDdHjke4D@rafael.j.wysocki
Instead of using one function, acpi_print_osc_error(), for printing a
debug message and dumping the _OSC request data in one go, use
acpi_handle_debug() directly for printing messages and a separate
function called acpi_dump_osc_data() for dumping the _OSC request data
before printing one or more of them.
This avoids
* dumping _OSC request data multiple times when there are
multiple error bits set in the return buffer,
* wrapping message lines on terminals with 80 character line width,
* mixing up unrelated messages by printing full lines only,
and generally helps to make the messages easier to parse.
Also, use %pUL for UUID printing instead of printing UUIDs as strings
and include the revision number into the dumped _OSC request data.
This is how the debug printout looks like when the
OSC_REQUEST_ERROR and OSC_INVALID_REVISION_ERROR bits
are set in the return buffer before the change:
ACPI: \_SB_: ACPI: (0811B06E-4A27-44F9-8D60-3CBBC22E7B48): _OSC request failed
ACPI: _OSC request data:
ACPI: 1
ACPI: 2e7eff
ACPI:
ACPI: \_SB_: ACPI: (0811B06E-4A27-44F9-8D60-3CBBC22E7B48): _OSC invalid revision
ACPI: _OSC request data:
ACPI: 1
ACPI: 2e7eff
ACPI:
and this is how it is going to look like afterward:
ACPI: \_SB_: ACPI: _OSC: UUID: 0811B06E-4A27-44F9-8D60-3CBBC22E7B48, rev: 1
ACPI: \_SB_: ACPI: _OSC: capabilities DWORD 0: [00000001]
ACPI: \_SB_: ACPI: _OSC: capabilities DWORD 1: [002e7eff]
ACPI: \_SB_: ACPI: _OSC: request failed
ACPI: \_SB_: ACPI: _OSC: invalid revision
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/10794028.nUPlyArG6x@rafael.j.wysocki
The handling of _OSC errors in acpi_run_osc() is inconsistent and
arguably not compliant with the _OSC definition (cf. Section 6.2.12 of
ACPI 6.6 [1]).
Namely, if OSC_QUERY_ENABLE is not set in the capabilities buffer and
any of the error bits are set in the _OSC return buffer, acpi_run_osc()
returns an error code and the _OSC return buffer is discarded. However,
in that case, depending on what error bits are set, the return buffer
may contain acknowledged bits for features that need to be controlled by
the kernel going forward.
If the OSC_INVALID_UUID_ERROR bit is set, the request could not be
processed at all and so in that particular case discarding the _OSC
return buffer and returning an error is the right thing to do regardless
of whether or not OSC_QUERY_ENABLE is set in the capabilities buffer.
If OSC_QUERY_ENABLE is set in the capabilities buffer and the
OSC_REQUEST_ERROR or OSC_INVALID_REVISION_ERROR bits are set in the
return buffer, acpi_run_osc() may return an error and discard the _OSC
return buffer because in that case the platform configuration does not
change. However, if any of them is set in the return buffer when
OSC_QUERY_ENABLE is not set in the capabilities buffer, the feature
mask in the _OSC return buffer still represents a set of acknowleded
features as per the _OSC definition:
The platform acknowledges the Capabilities Buffer by returning a
buffer of DWORDs of the same length. Set bits indicate acknowledgment
that OSPM may take control of the capability and cleared bits indicate
that the platform either does not support the capability or that OSPM
may not assume control.
which is not conditional on the error bits being clear, so in that case,
discarding the _OSC return buffer is questionable. There is also no
reason to return an error and discard the _OSC return buffer if the
OSC_CAPABILITIES_MASK_ERROR bit is set in it, but printing diagnostic
messages is appropriate when that happens with OSC_QUERY_ENABLE clear
in the capabilities buffer.
Adress this issue by making acpi_run_osc() follow the rules outlined
above.
Moreover, make acpi_run_osc() only take the defined _OSC error bits into
account when checking _OSC errors.
Link: https://uefi.org/specs/ACPI/6.6/06_Device_Configuration.html#osc-operating-system-capabilities [1]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
[ rjw: Corrected typo in the changelog ]
Link: https://patch.msgid.link/3042649.e9J7NaK4W3@rafael.j.wysocki
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
