The control flow in rtl8211f_config_init() has some pitfalls which were
probably unintended. Specifically it has an early return:
switch (phydev->interface) {
...
default: /* the rest of the modes imply leaving delay as is. */
return 0;
}
which exits the entire config_init() function. This means it also skips
doing things such as disabling CLKOUT or disabling PHY-mode EEE.
For the RTL8211FS, which uses PHY_INTERFACE_MODE_SGMII, this might be a
problem. However, I don't know that it is, so there is no Fixes: tag.
The issue was observed through code inspection.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251117234033.345679-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert the vmxnet3 driver to use the new .get_rx_ring_count ethtool
operation instead of implementing .get_rxnfc solely for handling
ETHTOOL_GRXRINGS command. This simplifies the code by removing the
switch statement and replacing it with a direct return of the queue
count.
The new callback provides the same functionality in a more direct way,
following the ongoing ethtool API modernization.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20251118-vmxnet3_grxrings-v1-1-ed8abddd2d52@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aditya Garg says:
====================
net: mana: Enforce TX SGE limit and fix error cleanup
Add pre-transmission checks to block SKBs that exceed the hardware's SGE
limit. Force software segmentation for GSO traffic and linearize non-GSO
packets as needed.
Update TX error handling to drop failed SKBs and unmap resources
immediately.
====================
Link: https://patch.msgid.link/1763464269-10431-1-git-send-email-gargaditya@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MANA hardware supports a maximum of 30 scatter-gather entries (SGEs)
per TX WQE. Exceeding this limit can cause TX failures.
Add ndo_features_check() callback to validate SKB layout before
transmission. For GSO SKBs that would exceed the hardware SGE limit, clear
NETIF_F_GSO_MASK to enforce software segmentation in the stack.
Add a fallback in mana_start_xmit() to linearize non-GSO SKBs that still
exceed the SGE limit.
Also, Add ethtool counter for SKBs linearized
Co-developed-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
Signed-off-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
Signed-off-by: Aditya Garg <gargaditya@linux.microsoft.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/1763464269-10431-2-git-send-email-gargaditya@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-11-18 (idpf, ice)
This series contains updates to idpf and ice drivers.
Emil adds a check for NULL vport_config during removal to avoid NULL
pointer dereference in idpf.
Grzegorz fixes PTP teardown paths to account for some missed cleanups
for ice driver.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: fix PTP cleanup on driver removal in error path
idpf: fix possible vport_config NULL pointer deref in remove
====================
Link: https://patch.msgid.link/20251118235207.2165495-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: misc fixes for v6.18-rc7
Here are various unrelated fixes:
- Patch 1: Fix window space computation for fallback connections which
can affect ACK generation. A fix for v5.11.
- Patch 2: Avoid unneeded subflow-level drops due to unsynced received
window. A fix for v5.11.
- Patch 3: Avoid premature close for fallback connections with PREEMPT
kernels. A fix for v5.12.
- Patch 4: Reset instead of fallback in case of data in the MPTCP
out-of-order queue. A fix for v5.7.
- Patches 5-7: Avoid also sending "plain" TCP reset when closing with an
MP_FASTCLOSE. A fix for v6.1.
- Patches 8-9: Longer timeout for background connections in MPTCP Join
selftests. An additional fix for recent patches for v5.13/v6.1.
- Patches 10-11: Fix typo in a check introduce in a recent refactoring.
A fix for v6.15.
====================
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-0-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous patch fixed an issue with the 'add_addr_accepted' counter.
This was not spot by the test suite.
Check this counter and 'add_addr_signal' in MPTCP Join 'delete re-add
signal' test. This should help spotting similar regressions later on.
These counters are crucial for ensuring the MPTCP path manager correctly
handles the subflow creation via 'ADD_ADDR'.
Signed-off-by: Gang Yan <yangang@kylinos.cn>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-11-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix inverted WARN_ON_ONCE condition that prevented normal address
removal counter updates. The current code only executes decrement
logic when the counter is already 0 (abnormal state), while
normal removals (counter > 0) are ignored.
Signed-off-by: Gang Yan <yangang@kylinos.cn>
Fixes: 6361139185 ("mptcp: pm: remove '_nl' from mptcp_pm_nl_rm_addr_received")
Cc: stable@vger.kernel.org
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-10-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rare cases, when the test environment is very slow, some userspace
tests can fail because some expected events have not been seen.
Because the tests are expecting a long on-going connection, and they are
not waiting for the end of the transfer, it is fine to have a longer
timeout, and even go over the default one. This connection will be
killed at the end, after the verifications: increasing the timeout
doesn't change anything, apart from avoiding it to end before the end of
the verifications.
To play it safe, all userspace tests not waiting for the end of the
transfer are now having a longer timeout: 2 minutes.
The Fixes commit was making the connection longer, but still, the
default timeout would have stopped it after 1 minute, which might not be
enough in very slow environments.
Fixes: 290493078b ("selftests: mptcp: join: userspace: longer transfer")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-9-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rare cases, when the test environment is very slow, some endpoints
tests can fail because some expected events have not been seen.
Because the tests are expecting a long on-going connection, and they are
not waiting for the end of the transfer, it is fine to have a longer
timeout, and even go over the default one. This connection will be
killed at the end, after the verifications: increasing the timeout
doesn't change anything, apart from avoiding it to end before the end of
the verifications.
To play it safe, all endpoints tests not waiting for the end of the
transfer are now having a longer timeout: 2 minutes.
The Fixes commit was making the connection longer, but still, the
default timeout would have stopped it after 1 minute, which might not be
enough in very slow environments.
Fixes: 6457595db9 ("selftests: mptcp: join: endpoints: longer transfer")
Cc: stable@vger.kernel.org
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-8-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After recent fixes like the parent commit, and "selftests: mptcp:
connect: trunc: read all recv data", the two fastclose subtests no
longer look flaky any more.
It then feels fine to remove these flaky marks, to no longer ignore
these subtests in case of errors.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-7-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CI reports sporadic failures of the fastclose self-tests. The root
cause is a duplicate reset, not carrying the relevant MPTCP option.
In the failing scenario the bad reset is received by the peer before
the fastclose one, preventing the reception of the latter.
Indeed there is window of opportunity at fastclose time for the
following race:
mptcp_do_fastclose
__mptcp_close_ssk
__tcp_close()
tcp_set_state() [1]
tcp_send_active_reset() [2]
After [1] the stack will send reset to in-flight data reaching the now
closed port. Such reset may race with [2].
Address the issue explicitly sending a single reset on fastclose before
explicitly moving the subflow to close status.
Fixes: d21f834855 ("mptcp: use fastclose on more edge scenarios")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/596
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-6-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the current fastclose implementation, the mptcp_do_fastclose()
helper is in charge of two distinct actions: send the fastclose reset
and cleanup the subflows.
Formally decouple the two steps, ensuring that mptcp explicitly closes
all the subflows after the mentioned helper.
This will make the upcoming fix simpler, and allows dropping the 2nd
argument from mptcp_destroy_common(). The Fixes tag is then the same as
in the next commit to help with the backports.
Fixes: d21f834855 ("mptcp: use fastclose on more edge scenarios")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-5-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of DSS corruption, the MPTCP protocol tries to avoid the subflow
reset if fallback is possible. Such corruptions happen in the receive
path; to ensure fallback is possible the stack additionally needs to
check for OoO data, otherwise the fallback will break the data stream.
Fixes: e32d262c89 ("mptcp: handle consistently DSS corruption")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/598
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-4-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I'm observing very frequent self-tests failures in case of fallback when
running on a CONFIG_PREEMPT kernel.
The root cause is that subflow_sched_work_if_closed() closes any subflow
as soon as it is half-closed and has no incoming data pending.
That works well for regular subflows - MPTCP needs bi-directional
connectivity to operate on a given subflow - but for fallback socket is
race prone.
When TCP peer closes the connection before the MPTCP one,
subflow_sched_work_if_closed() will schedule the MPTCP worker to
gracefully close the subflow, and shortly after will do another schedule
to inject and process a dummy incoming DATA_FIN.
On CONFIG_PREEMPT kernel, the MPTCP worker can kick-in and close the
fallback subflow before subflow_sched_work_if_closed() is able to create
the dummy DATA_FIN, unexpectedly interrupting the transfer.
Address the issue explicitly avoiding closing fallback subflows on when
the peer is only half-closed.
Note that, when the subflow is able to create the DATA_FIN before the
worker invocation, the worker will change the msk state before trying to
close the subflow and will skip the latter operation as the msk will not
match anymore the precondition in __mptcp_close_subflow().
Fixes: f09b0ad55a ("mptcp: close subflow when receiving TCP+FIN")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-3-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rcv window is shared among all the subflows. Currently, MPTCP sync
the TCP-level rcv window with the MPTCP one at tcp_transmit_skb() time.
The above means that incoming data may sporadically observe outdated
TCP-level rcv window and being wrongly dropped by TCP.
Address the issue checking for the edge condition before queuing the
data at TCP level, and eventually syncing the rcv window as needed.
Note that the issue is actually present from the very first MPTCP
implementation, but backports older than the blamed commit below will
range from impossible to useless.
Before:
$ nstat -n; sleep 1; nstat -z TcpExtBeyondWindow
TcpExtBeyondWindow 14 0.0
After:
$ nstat -n; sleep 1; nstat -z TcpExtBeyondWindow
TcpExtBeyondWindow 0 0.0
Fixes: fa3fe2b150 ("mptcp: track window announced to peer")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-2-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mptcp_cleanup_rbuf() needs to know the last most recent, mptcp-level
rcv_wnd sent, and such information is tracked into the msk->old_wspace
field, updated at ack transmission time by mptcp_write_options().
Fallback socket do not add any mptcp options, such helper is never
invoked, and msk->old_wspace value remain stale. That in turn makes
ack generation at recvmsg() time quite random.
Address the issue ensuring mptcp_write_options() is invoked even for
fallback sockets, and just update the needed info in such a case.
The issue went unnoticed for a long time, as mptcp currently overshots
the fallback socket receive buffer autotune significantly. It is going
to change in the near future.
Fixes: e3859603ba ("mptcp: better msk receive window updates")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/594
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251118-net-mptcp-misc-fixes-6-18-rc6-v1-1-806d3781c95f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the TM tree is printing all SQ topology including those
which are not enabled, this results in redundant output for SQs
which are not active. This patch adds a check in print_tm_tree()
to skip printing the TM tree hierarchy if the SQ is not enabled.
Signed-off-by: Anshumali Gaur <agaur@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251118054235.1599714-1-agaur@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that the linux-scsi mailing list is Cc-ed for changes to UFS
include headers.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20251119165742.536170-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow user space software, e.g. a blktests test, to inject unaligned
write errors.
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20251113174151.1095574-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In qla2xxx_process_purls_iocb(), an item is allocated via
qla27xx_copy_multiple_pkt(), which internally calls
qla24xx_alloc_purex_item().
The qla24xx_alloc_purex_item() function may return a pre-allocated item
from a per-adapter pool for small allocations, instead of dynamically
allocating memory with kzalloc().
An error handling path in qla2xxx_process_purls_iocb() incorrectly uses
kfree() to release the item. If the item was from the pre-allocated
pool, calling kfree() on it is a bug that can lead to memory corruption.
Fix this by using the correct deallocation function,
qla24xx_free_purex_item(), which properly handles both dynamically
allocated and pre-allocated items.
Fixes: 875386b988 ("scsi: qla2xxx: Add Unsolicited LS Request and Response Support for NVMe")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Himanshu Madhani <hmadhani2024@gmail.com>
Link: https://patch.msgid.link/20251113151246.762510-1-zilin@seu.edu.cn
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scanning can be offloaded to the firmware. To that end, the driver
prepares a list of channels to scan, including periodic visits back to
the operating channel, and sends the list to the firmware.
When the channel list is too long to fit in a single H2C message, the
driver splits the list, sends the first part, and tells the firmware to
scan. When the scan is complete, the driver sends the next part of the
list and tells the firmware to scan.
When the last channel that fit in the H2C message is the operating
channel something seems to go wrong in the firmware. It will
acknowledge receiving the list of channels but apparently it will not
do anything more. The AP can't be pinged anymore. The driver still
receives beacons, though.
One way to avoid this is to split the list of channels before the
operating channel.
Affected devices:
* RTL8851BU with firmware 0.29.41.3
* RTL8832BU with firmware 0.29.29.8
* RTL8852BE with firmware 0.29.29.8
The commit 57a5fbe39a ("wifi: rtw89: refactor flow that hw scan handles channel list")
is found by git blame, but it is actually to refine the scan flow, but not
a culprit, so skip Fixes tag.
Reported-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/0abbda91-c5c2-4007-84c8-215679e652e1@gmail.com/
Cc: stable@vger.kernel.org # 6.16+
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/c1e61744-8db4-4646-867f-241b47d30386@gmail.com
drivers/ufs/host/ufs-rockchip.c:168:19: error: implicit declaration of function
'devm_gpiod_get'; did you mean 'em_pd_get'? [-Werror=implicit-function-declaration]
drivers/ufs/host/ufs-rockchip.c:214:2: error: implicit declaration of function
'gpiod_set_value_cansleep'; did you mean 'gpio_set_value_cansleep'?
[-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202511130238.LlA0MKxW-lkp@intel.com/
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/1763011091-243727-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This fixes the dme-reset failed when doing recovery. Because device
reset is not enough, we could occasionally see the error below:
ufshcd-rockchip 2a2d0000.ufs: uic cmd 0x14 with arg3 0x0 completion timeout
ufshcd-rockchip 2a2d0000.ufs: dme-reset: error code -110
ufshcd-rockchip 2a2d0000.ufs: DME_RESET failed
ufshcd-rockchip 2a2d0000.ufs: ufshcd_host_reset_and_restore: Host init failed -110
Fix this by resetting the controller on PRE_CHANGE stage of hce enable
notify.
Fixes: d3cbe455d6 ("scsi: ufs: rockchip: Initial support for UFS")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://patch.msgid.link/1763009575-237552-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Different SoCs have different numbers of Wireless Ethernet
Dispatch (WED) units:
- MT7981: Has 1 WED unit
- MT7986: Has 2 WED units
- MT7988: Has 2 WED units
Update the binding to reflect these hardware differences. The MT7981
also uses infracfg for PHY switching, so allow that property.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20251115-openwrt-one-network-v4-6-48cbda2969ac@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rather than perf_pmu__is_xxx calls, and a notion of kind so that a
single call can be used.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Writing currently fails on non-x86 and hybrid CPUs. Switch to the more
regular find_core_pmu that is normally used in this case. Tested on
hybrid alderlake system.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Rust
- Make slice::as_flattened usable on all supported versions of rustc.
- Add FromBytes::from_bytes_prefix() method.
Core Changes:
- Update Tyr in MAINTAINERS file.
- Remove redundant device ptr from Rust GEM object.
- Change how AlwaysRefCounted is implemented for GEM objects.
- Add deferred vm_bo cleanup to GPUVM and use it in Panthor.
Driver Changes:
Nova Core
- Introduction of bitfield! macro, with support for different storage sizes
and custom visibility.
- Introduction of safe converters between integer types for which the
conversion is lossless.
- GSP initialized up to fully booted state on Ampere.
- Use more future-proof register for GPU identification.
- Various simplifications and optimizations.
Nova
- Select NOVA_CORE.
- Depend on CONFIG_64BIT.
-----BEGIN PGP SIGNATURE-----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=yKU+
-----END PGP SIGNATURE-----
Merge tag 'drm-rust-next-2025-11-18' of https://gitlab.freedesktop.org/drm/rust/kernel into drm-next
Cross-subsystem Changes:
Rust
- Make slice::as_flattened usable on all supported versions of rustc.
- Add FromBytes::from_bytes_prefix() method.
Core Changes:
- Update Tyr in MAINTAINERS file.
- Remove redundant device ptr from Rust GEM object.
- Change how AlwaysRefCounted is implemented for GEM objects.
- Add deferred vm_bo cleanup to GPUVM and use it in Panthor.
Driver Changes:
Nova Core
- Introduction of bitfield! macro, with support for different storage sizes
and custom visibility.
- Introduction of safe converters between integer types for which the
conversion is lossless.
- GSP initialized up to fully booted state on Ampere.
- Use more future-proof register for GPU identification.
- Various simplifications and optimizations.
Nova
- Select NOVA_CORE.
- Depend on CONFIG_64BIT.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alice Ryhl <aliceryhl@google.com>
Link: https://patch.msgid.link/aRxtJC0D1pQUepF4@google.com
Add additional test to the maps covering
maps__fixup_overlap_and_insert. Change the test suite to be for more
than just 1 test.
Signed-off-by: Ian Rogers <irogers@google.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The case of __maps__fixup_overlap_and_insert where the "new" maps
covers existing mappings can create a use-after-free with reference
count checking enabled. The issue is that "pos" holds a map pointer
from maps_by_address that is put from maps_by_address but then used to
look for a map in maps_by_name (the compared map is now a
use-after-free). The issue stems from using maps__remove which redoes
some of the searches already done by __maps__fixup_overlap_and_insert,
so optimize the code (by avoiding repeated searches) and avoid the
use-after-free by inlining the appropriate removal code.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202511141407.f9edcfa6-lkp@intel.com
Signed-off-by: Ian Rogers <irogers@google.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The current mute_steam() implementation affects all paths instead of
only those in use by the DAI.
For example, playing to 2 DAIs simultaneously with mixing, stopping
one will mute the other.
Rework to use the same logic as hw_params() to mute only the relevant paths.
(also, use "rx->main_clk_users[j] > 0" instead of dsm_reg, which is
equivalent. I also don't think the clock enable should be in this function,
but that's a change for another patch)
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251117051523.16462-9-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
The event enables the main path clock when the mux is set to DEC0/DEC1.
My patch ("ASoC: codecs: lpass-wsa-macro: fix path clock dependencies")
makes it depend on the main path clock, so this event is now redundant.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251117051523.16462-6-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows changing the mix gain registers from the default value.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251117051523.16462-5-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
"WSA_RX0_CLK",etc. are path clocks, but "WSA RX0",etc. are ports, and there
isn't a correspondence between the ports and paths.
For example "WSA RX0" port could be used by the "RX1 MIX" path.
The problem becomes obvious when RX4,etc. ports are added.
Enabling the path clocks should depend on the path being enabled.
With this fix, the main path clock will be enabled whenever the path is
active: previously using the mix ports only would only activate the mix
path clock and no audio would play.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251117051523.16462-4-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
All it does it disable the mix path clk bit, but this is already managed by
the WSA_RX_MIX0_CLK/WSA_RX_MIX1_CLK supplies.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251117051523.16462-3-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Reading and writing the same value to this register does nothing.
Looking at downstream driver it seems there was meant to be an offset added
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>> ---
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251117051523.16462-2-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
WSA_MACRO_RX0 is 0 and WSA_MACRO_RX_MIX1 is (WSA_MACRO_RX_MAX-1), which
means it is not possible for the bounds check to fail.
Removing the WSA_MACRO_RX_MIX1 limit is needed to add support for other
ports (RX4, RX5, etc.), in which case the valid range depends on the HW
version: rely on the driver only setting valid ports in active_ch_mask
instead (already the case).
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Link: https://patch.msgid.link/20251117051523.16462-1-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f1eb4e792b ("spi: spi-cadence-quadspi: Enable pm runtime earlier
to avoid imbalance") relocated code but missed updating the error handling
path associated with it.
Prior to the relocation, runtime pm was enabled after the code-block
associated with 'cqspi_request_mmap_dma()', due to which, the error
handling for the same didn't require invoking 'pm_runtime_disable()'.
Post refactoring, runtime pm has been enabled before the code-block and
when an error is encountered, jumping to 'probe_dma_failed' doesn't
invoke 'pm_runtime_disable()'. This leads to a race condition wherein
'cqspi_runtime_suspend()' is invoked while the error handling path executes
in parallel. The resulting error is the following:
clk:103:0 already disabled
WARNING: drivers/clk/clk.c:1188 at clk_core_disable+0x80/0xa0, CPU#1: kworker/u8:0/12
[TRIMMED]
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : clk_core_disable+0x80/0xa0
lr : clk_core_disable+0x80/0xa0
[TRIMMED]
Call trace:
clk_core_disable+0x80/0xa0 (P)
clk_core_disable_lock+0x88/0x10c
clk_disable+0x24/0x30
cqspi_probe+0xa3c/0xae8
[TRIMMED]
The error is due to the second invocation of 'clk_disable_unprepare()' on
'cqspi->clk' in the error handling within 'cqspi_probe()', with the first
invocation being within 'cqspi_runtime_suspend()'.
Fix this by correcting the error handling.
Fixes: f1eb4e792b ("spi: spi-cadence-quadspi: Enable pm runtime earlier to avoid imbalance")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20251119152545.2591651-1-s-vadapalli@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The MMIO_REMAP BO is a special 4K IO page that does not have a ttm_tt
behind it. However, amdgpu_ttm_tt_pde_flags() was treating it like
normal TT/doorbell/preempt memory and unconditionally accessed
ttm->caching. For the MMIO_REMAP BO, ttm is NULL, so this leads to a
NULL pointer dereference when computing PDE flags.
Fix this by checking that ttm is non-NULL before reading ttm->caching.
This prevents the crash for MMIO_REMAP and also makes the code more
defensive if other BOs ever come through without a ttm_tt.
Fixes: fb5a52dbe9 ("drm/amdgpu: Implement TTM handling for MMIO_REMAP placement")
Suggested-by: Jesse Zhang <Jesse.Zhang@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Jesse Zhang <Jesse.Zhang@amd.com>
Tested-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 0db94da5a0)
This fixes sparse mappings (aka. partially resident textures).
Check the correct flags.
Since a recent refactor, the code works with uAPI flags (for
mapping buffer objects), and not PTE (page table entry) flags.
Fixes: 6716a823d1 ("drm/amdgpu: rework how PTE flags are generated v3")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8feeab26c8)
[Why]
Accoreding to CP updated to RS64 on gfx11,
WRITE_DATA with PREEMPTION_META_MEMORY(dst_sel=8) is illegal for CP FW.
That packet is used for MCBP on F32 based system.
So it would lead to incorrect GRBM write and FW is not handling that
extra case correctly.
[How]
With gfx11 rs64 enabled, skip emit de meta data.
Signed-off-by: Yifan Zha <Yifan.Zha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8366cd442d)
Cc: stable@vger.kernel.org
During the suspend sequence VPE is already going to be power gated
as part of vpe_suspend(). It's unnecessary to call during calls to
amdgpu_device_set_pg_state().
It actually can expose a race condition with the firmware if s0i3
sequence starts as well. Drop these calls.
Cc: Peyton.Lee@amd.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2a6c826cfe)
Cc: stable@vger.kernel.org
The function mtk_dp_dt_parse() calls of_graph_get_endpoint_by_regs()
to get the endpoint device node, but fails to call of_node_put() to release
the reference when the function returns. This results in a device node
reference leak.
Fix this by adding the missing of_node_put() call before returning from
the function.
Found via static analysis and code review.
Fixes: f70ac097a2 ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20251029072307.10955-1-linmq006@gmail.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Since the ftrace fprobe is both fgraph and ftrace based implemented,
the selftest needs to be updated. This does not count the actual
number of lines, but just check the differences.
Link: https://lore.kernel.org/r/176295318112.431538.11780280333728368327.stgit@devnote2
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
