GMU registers are always at a fixed offset from the GPU base address,
a consistency maintained at least within a given architecture generation.
In A8x family, the base address of the GMU has changed, but the offsets
of the gmu registers remain largely the same. To enable reuse of the gmu
code for A8x chipsets, update the gmu register offsets to be relative
to the GPU's base address instead of GMU's.
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/689010/
Message-ID: <20251118-kaana-gpu-support-v4-10-86eeb8e93fb6@oss.qualcomm.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Sync the latest register definitions from Mesa which includes the
updates for A8x family.
Co-developed-by: Rob Clark <robin.clark@oss.qualcomm.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/689009/
Message-ID: <20251118-kaana-gpu-support-v4-9-86eeb8e93fb6@oss.qualcomm.com>
Use %pe to print a PTR_ERR to silence a cocci warning
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Closes: https://lore.kernel.org/r/202510300342.WtPn2jF3-lkp@intel.com/
Signed-off-by: Stuart Hayhurst <stuart.a.hayhurst@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
[Why]
When a monitor is booting it's possible that it isn't ready to retrieve
link caps and this can lead to an EDID read failure:
```
[drm:retrieve_link_cap [amdgpu]] *ERROR* retrieve_link_cap: Read receiver caps dpcd data failed.
amdgpu 0000:c5:00.0: [drm] *ERROR* No EDID read.
```
[How]
Rather than msleep once and try a few times, msleep each time. Should
be no changes for existing working monitors, but should correct reading
caps on a monitor that is slow to boot.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4672
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 669dca37b3)
Cc: stable@vger.kernel.org
Remove extra space after '=' to comply with coding style.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Peter Griffin <peter.griffin@linaro.org> says:
This series adds a new phy_notify_state() API to the phy subsystem. It is
designed to be used when some specific runtime configuration parameters
need to be changed when transitioning to the desired state which can't be
handled by phy_calibrate()or phy_power_{on|off}().
The first user of the new API is phy-samsung-ufs and phy-gs101-ufs which
need to issue some register writes when entering and exiting the hibern8
link state.
A separate patch will be sent for ufs-exynos driver to make use of this new
API in the hibern8 callbacks.
Link: https://patch.msgid.link/20251112-phy-notify-pmstate-v5-0-39df622d8fcb@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Implement the .notify_phystate() callback and provide the gs101 specific
phy values that need to be programmed when entering and exiting the hibern8
state.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251112-phy-notify-pmstate-v5-2-39df622d8fcb@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a new phy_notify_state() api that notifies and configures a phy for a
given state transition.
This is intended to be used by phy drivers which need to do some runtime
configuration of parameters that can't be handled by phy_calibrate() or
phy_power_{on|off}().
The first usage of this API is in the Samsung UFS phy that needs to issue
some register writes when entering and exiting the hibernate link state.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251112-phy-notify-pmstate-v5-1-39df622d8fcb@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The ELECOM M-XT3URBK trackball has an additional device ID (0x018F), which
shares the same report descriptor as the existing device (0x00FB). However,
the driver does not currently recognize this new ID, resulting in only five
buttons being functional.
This patch adds the new device ID so that all six buttons work properly.
Signed-off-by: Naoki Ueki <naoki25519@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
In "Packet Format" section, only "StickPointer data byte" subsection
heading is shown as such in htmldocs output; "Touchpad data byte" one
is in normal paragraph on the other hand.
Properly format the headings to be consistent.
Fixes: 2562756dde ("HID: add Alps I2C HID Touchpad-Stick support")
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
RESET_CONTROL_FLAGS_BIT_* macros use BIT(), but reset.h does not
include bits.h. This causes compilation errors when including
reset.h standalone.
Include bits.h to make reset.h self-contained.
Suggested-by: Troy Mitchell <troy.mitchell@linux.dev>
Reviewed-by: Troy Mitchell <troy.mitchell@linux.dev>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Encrow Thorne <jyc0019@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The devm_regmap_field_alloc() function never returns NULL, it returns
error pointers. Update the error checking to match.
Fixes: 58128aa88867 ("reset: rzg2l-usbphy-ctrl: Add support for USB PWRRDY")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Introduce reset controllers for AP, MISC, VI, VP and DSP subsystems and
add their reset signal mappings.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Acked-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
TH1520 SoC is divided into several subsystems, shipping distinct reset
controllers with similar control logic. Let's make reset signal mapping
a data structure specific to one compatible to prepare for introduction
of more reset controllers in the future.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Acked-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
TH1520 SoC is divided into several subsystems, most of them have
distinct reset controllers. Let's document reset controllers other than
the one for VO subsystem and IDs for their reset signals.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Acked-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Registers in control of TH1520_RESET_ID_{NPU,WDT0,WDT1} belong to AP
reset controller, not the VO one which is documented as
"thead,th1520-reset" and is the only reset controller supported for
TH1520 for now.
Let's remove the IDs, leaving them to be implemented by AP-subsystem
reset controller in the future.
Fixes: 30e7573bab ("dt-bindings: reset: Add T-HEAD TH1520 SoC Reset Controller")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Acked-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
There are no more users of this code. Let's remove the exported symbols
and the implementation from reset core.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
[p.zabel@pengutronix.de: folded in 8e6ec20e-8965-4b42-99fc-0462269ff2f1@paulmck-laptop]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
We no longer support any non-DT DaVinci boards so there are no more
users of legacy reset lookup.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: David Lechner <david@lechnology.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Renesas RZ/G3S SoC USB PHY HW block receives as input the USB PWRRDY
signal from the system controller. Add support for the Renesas RZ/G3S SoC.
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
On the Renesas RZ/G3S SoC, the USB PHY block has an input signal called
PWRRDY. This signal is managed by the system controller and must be
de-asserted after powering on the area where USB PHY resides and asserted
before powering it off.
On power-on/resume the USB PWRRDY signal need to be de-asserted before
enabling clock and switching the module to normal state (through MSTOP
support). The power-on/resume configuration sequence must be:
1/ PWRRDY=0
2/ CLK_ON=1
3/ MSTOP=0
On power-off/suspend the configuration sequence should be:
1/ MSTOP=1
2/ CLK_ON=0
3/ PWRRDY=1
The CLK_ON and MSTOP functionalities are controlled by clock drivers.
The suspend/resume support will be handled by different patches.
After long discussions with the internal HW team, it has been confirmed
that the HW connection b/w USB PHY block, the USB channels, the system
controller, clock, MSTOP, PWRRDY signal is as follows:
┌──────────────────────────────┐
│ │◄── CPG_CLKON_USB.CLK0_ON
│ USB CH0 │
┌──────────────────────────┐ │┌───────────────────────────┐ │◄── CPG_CLKON_USB.CLK2_ON
│ ┌────────┐ ││host controller registers │ │
│ │ │ ││function controller registers│
│ │ PHY0 │◄──┤└───────────────────────────┘ │
│ USB PHY │ │ └────────────▲─────────────────┘
│ └────────┘ │
│ │ CPG_BUS_PERI_COM_MSTOP.MSTOP{6, 5}_ON
│┌──────────────┐ ┌────────┐
││USHPHY control│ │ │
││ registers │ │ PHY1 │ ┌──────────────────────────────┐
│└──────────────┘ │ │◄──┤ USB CH1 │
│ └────────┘ │┌───────────────────────────┐ │◄── CPG_CLKON_USB.CLK1_ON
└─▲───────▲─────────▲──────┘ ││ host controller registers │ │
│ │ │ │└───────────────────────────┘ │
│ │ │ └────────────▲─────────────────┘
│ │ │ │
│ │ │ CPG_BUS_PERI_COM_MSTOP.MSTOP7_ON
│PWRRDY │ │
│ │ CPG_CLK_ON_USB.CLK3_ON
│ │
│ CPG_BUS_PERI_COM_MSTOP.MSTOP4_ON
│
┌────┐
│SYSC│
└────┘
where:
- CPG_CLKON_USB.CLK.CLKX_ON is the register bit controlling the clock X
of different USB blocks, X in {0, 1, 2, 3}
- CPG_BUS_PERI_COM_MSTOP.MSTOPX_ON is the register bit controlling the
MSTOP of different USB blocks, X in {4, 5, 6, 7}
- USB PHY is the USB PHY block exposing 2 ports, port0 and port1, used
by the USB CH0, USB CH1
- SYSC is the system controller block controlling the PWRRDY signal
- USB CHx are individual USB block with host and function capabilities
(USB CH0 have both host and function capabilities, USB CH1 has only
host capabilities)
The USBPHY control registers are controlled though the
reset-rzg2l-usbphy-ctrl driver. The USB PHY ports are controlled by
phy_rcar_gen3_usb2 (drivers/phy/renesas/phy-rcar-gen3-usb2.c file). The
USB PHY ports request resets from the reset-rzg2l-usbphy-ctrl driver.
The connection b/w the system controller and the USB PHY CTRL driver is
implemented through the renesas,sysc-pwrrdy device tree property
proposed in this patch. This property specifies the register offset and the
bitmask required to control the PWRRDY signal.
Since the USB PHY CTRL driver needs to be probed before any other
USB-specific driver on RZ/G3S, control of PWRRDY is passed exclusively
to it. This guarantees the correct configuration sequence between clocks,
MSTOP bits, and the PWRRDY bit on probe/resume and remove/suspend. At the
same time, changes are kept minimal by avoiding modifications to the USB
PHY driver to also handle the PWRRDY itself.
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Renesas USB PHY hardware block needs to have the PWRRDY bit in the
system controller set before applying any other settings. The PWRRDY bit
must be controlled during power-on, power-off, and system suspend/resume
sequences as follows:
- during power-on/resume, it must be set to zero before enabling clocks and
modules
- during power-off/suspend, it must be set to one after disabling clocks
and modules
Add the renesas,sysc-pwrrdy device tree property, which allows the
reset-rzg2l-usbphy-ctrl driver to parse, map, and control the system
controller PWRRDY bit at the appropriate time. Along with it add a new
compatible for the RZ/G3S SoC.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add support for reset controller in eic7700 series chips.
Provide functionality for asserting and deasserting resets
on the chip.
Signed-off-by: Yifeng Huang <huangyifeng@eswincomputing.com>
Signed-off-by: Xuyang Dong <dongxuyang@eswincomputing.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
LAN969x uses the same reset configuration as LAN966x, but we need to
allow compiling it when ARCH_LAN969X is selected.
A fallback compatible to LAN966x will be used.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
LAN969x also uses the Microchip reset driver, it reuses the LAN966x
support so use a fallback compatible.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Don't update the LBR MSR intercept bitmaps if they're already up-to-date,
as unconditionally updating the intercepts forces KVM to recalculate the
MSR bitmaps for vmcb02 on every nested VMRUN. The redundant updates are
functionally okay; however, they neuter an optimization in Hyper-V
nested virtualization enlightenments and this manifests as a self-test
failure.
In particular, Hyper-V lets L1 mark "nested enlightenments" as clean, i.e.
tell KVM that no changes were made to the MSR bitmap since the last VMRUN.
The hyperv_svm_test KVM selftest intentionally changes the MSR bitmap
"without telling KVM about it" to verify that KVM honors the clean hint,
correctly fails because KVM notices the changed bitmap anyway:
==== Test Assertion Failure ====
x86/hyperv_svm_test.c:120: vmcb->control.exit_code == 0x081
pid=193558 tid=193558 errno=4 - Interrupted system call
1 0x0000000000411361: assert_on_unhandled_exception at processor.c:659
2 0x0000000000406186: _vcpu_run at kvm_util.c:1699
3 (inlined by) vcpu_run at kvm_util.c:1710
4 0x0000000000401f2a: main at hyperv_svm_test.c:175
5 0x000000000041d0d3: __libc_start_call_main at libc-start.o:?
6 0x000000000041f27c: __libc_start_main_impl at ??:?
7 0x00000000004021a0: _start at ??:?
vmcb->control.exit_code == SVM_EXIT_VMMCALL
Do *not* fix this by skipping svm_hv_vmcb_dirty_nested_enlightenments()
when svm_set_intercept_for_msr() performs a no-op change. changes to
the L0 MSR interception bitmap are only triggered by full CPUID updates
and MSR filter updates, both of which should be rare. Changing
svm_set_intercept_for_msr() risks hiding unintended pessimizations
like this one, and is actually more complex than this change.
Fixes: fbe5e5f030 ("KVM: nSVM: Always recalculate LBR MSR intercepts in svm_update_lbrv()")
Cc: stable@vger.kernel.org
Signed-off-by: Yosry Ahmed <yosry.ahmed@linux.dev>
Link: https://patch.msgid.link/20251112013017.1836863-1-yosry.ahmed@linux.dev
[Rewritten commit message based on mailing list discussion. - Paolo]
Reviewed-by: Sean Christopherson <seanjc@google.com>
Tested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[why]
1. With allow_0_dtb_clk enabled, the time required to latch DTBCLK to 600 MHz
depends on the SMU. If DTBCLK is not latched to 600 MHz before set_mode completes,
gating DTBCLK causes the DP2 sink to lose its clock source.
2. The existing DTBCLK gating sequence ungates DTBCLK based on both pix_clk and ref_dtbclk,
but gates DTBCLK when either pix_clk or ref_dtbclk is zero.
pix_clk can be zero outside the set_mode sequence before DTBCLK is properly latched,
which can lead to DTBCLK being gated by mistake.
[how]
Consider both pixel_clk and ref_dtbclk when determining when it is safe to gate DTBCLK;
this is more accurate.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4701
Fixes: 5949e7c489 ("drm/amd/display: Enable Dynamic DTBCLK Switch")
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d04eb0c402)
Cc: stable@vger.kernel.org
- Only adjust the ID registers when no irqchip has been created once
per VM run, instead of doing it once per vcpu, as this otherwise
triggers a pretty bad conbsistency check failure in the sysreg code.
- Make sure the per-vcpu Fine Grain Traps are computed before we load
the system registers on the HW, as we otherwise start running without
anything set until the first preemption of the vcpu.
-----BEGIN PGP SIGNATURE-----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=MCeE
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.18, take #3
- Only adjust the ID registers when no irqchip has been created once
per VM run, instead of doing it once per vcpu, as this otherwise
triggers a pretty bad conbsistency check failure in the sysreg code.
- Make sure the per-vcpu Fine Grain Traps are computed before we load
the system registers on the HW, as we otherwise start running without
anything set until the first preemption of the vcpu.
Currently ISAPNP devices do not generate an uevent for udev to
auto-load the driver modules for Creative SoundBlaster or Gravis
UltraSound to just work.
Signed-off-by: René Rebe <rene@exactco.de>
[ rjw: Subject edits ]
Link: https://patch.msgid.link/20251118.145942.1445519082574147037.rene@exactco.de
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ECPRI clock controller’s mem_ops clocks used the mem_enable_ack_mask
directly for both setting and polling.
Add the newly introduced 'mem_enable_mask' to the memory control branch
clocks of ECPRI clock controller to align to the new mem_ops handling.
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Imran Shaik <imran.shaik@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251118-sm8750-videocc-v2-v4-2-049882a70c9f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Introduce mem_enable_mask and mem_enable_invert in clk_mem_branch to
describe memory gating implementations that use a separate mask and/or
inverted enable logic. This documents hardware behavior in data instead
of code and will be used by upcoming platform descriptions.
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Imran Shaik <imran.shaik@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251118-sm8750-videocc-v2-v4-1-049882a70c9f@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add offset for display subsystem reset in multimedia clock controller
block, which is necessary to reset display when there is some
configuration in display controller left by previous stock (Android)
bootloader to provide continuous splash functionaluty.
Before 6.17 power domains were turned off for long enough to clear
registers, now this is not the case and a proper reset is needed to
have functioning display.
Fixes: 0e789b491b ("pmdomain: core: Leave powered-on genpds on until sync_state")
Cc: stable@vger.kernel.org # 6.17
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Taniya Das <taniya.das@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251116-sdm660-mdss-reset-v2-2-6219bec0a97f@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add definition for display subsystem reset control, so display
driver can reset display controller properly, clearing any
configuration left there by bootloader. Since 6.17 after
PM domains rework it became necessary for display to function.
Fixes: 0e789b491b ("pmdomain: core: Leave powered-on genpds on until sync_state")
Cc: stable@vger.kernel.org # 6.17
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20251116-sdm660-mdss-reset-v2-1-6219bec0a97f@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
scripts/lib was always a bit of an awkward place for Python libraries; give
them a proper home under tools/lib/python. Put the modules from
tools/docs/lib there for good measure.
The second patch ties them into a single package namespace. It would be
more aesthetically pleasing to add a kernel layer, so we could say:
from kernel.kdoc import kdoc_parser
...and have the kernel-specific stuff clearly marked, but that means adding
an empty directory in the hierarchy, which isn't as pleasing.
There are some other "Python library" directories hidden in the kernel
tree; we may eventually want to encourage them to move as well.
Now that we have tools/lib/python for our Python modules, turn them into
proper packages with a single namespace so that everything can just use
tools/lib/python in sys.path. No functional change.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Message-ID: <20251110220430.726665-3-corbet@lwn.net>
"scripts/lib" was always a bit of an awkward place for Python modules. We
already have tools/lib; create a tools/lib/python, move the libraries
there, and update the users accordingly.
While at it, move the contents of tools/docs/lib. Rather than make another
directory, just put these documentation-oriented modules under "kdoc".
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Message-ID: <20251110220430.726665-2-corbet@lwn.net>
The recent fix to properly initialize the tags of the huge zero folio
had an unfortunate not-so-subtle side effect: it caused the actual
*contents* of the huge zero folio to not be initialized at all when the
hardware didn't support the memory tagging.
The reason was the unfortunate semantics of tag_clear_highpage(): on
hardware that didn't do the tagging, it would silently just not do
anything at all. And since this is done only on arm64 with MTE support,
that basically meant most hardware.
It wasn't necessarily immediately obvious since the huge zero page isn't
necessarily very heavily used - or because it might already be zero
because all-zeroes is the most common pattern. But it ends up causing
random odd user space failures when you do hit it.
The unfortunate semantics have been around for a while, but became a
real bug only when we started actively using __GFP_ZEROTAGS in the
generic get_huge_zero_folio() function - before that, it had only ever
been used in code that checked that the hardware supported it.
Fix this by simply changing the semantics of tag_clear_highpage() to
return whether it actually successfully did something or not. While at
it, also make it initialize multiple pages in one go, since that's
actually what the only caller wants it to do and it simplifies the whole
logic.
Fixes: adfb6609c6 ("mm/huge_memory: initialise the tags of the huge zero folio")
Link: https://lore.kernel.org/all/20251117082023.90176-1-00107082@163.com/
Reviewed-by: David Hildenbrand (Red Hat) <david@kernel.org>
Reported-and-tested-by: David Wang <00107082@163.com>
Reported-and-tested-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the kernel build options abbreviations to the .txt file so that
they are together instead of one having to go hunt them in the .rst
file.
Tweak the formatting so that the inclusion of kernel-parameters.txt
still keeps the whole thing somewhat presentable in the html output too.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Message-ID: <20251112114641.8230-1-bp@kernel.org>
Replace "vantage" with "advantage" in the description of userspace API
cross-references.
Signed-off-by: Ankit Khushwaha <ankitkhushwaha.linux@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Message-ID: <20251115114233.32239-1-ankitkhushwaha.linux@gmail.com>
Instead of checking that the signal is analog before calling the
HWSS disable_audio_stream() function to disable audio, move
the check inside the HWSS function.
Suggested-by: Ray Wu <Ray.Wu@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://lore.kernel.org/r/20251113163348.137315-5-timur.kristof@gmail.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Match pre-existing patterns in the DC code base.
Instead of returning early from the construct_phy() function,
add a label at the end and use goto to jump there.
Additionally, respect the DC logger and let it log the function
even when it returns early.
Suggested-by: Ray Wu <Ray.Wu@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://lore.kernel.org/r/20251113163348.137315-4-timur.kristof@gmail.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the detect_link_and_local_sink() function, do not modify the
EDID capabilities of the display based on the connector. Instead,
respect the analog flag better and when the analog flag is set,
check that the connector indeed supports analog displays.
Suggested-by: Ray Wu <Ray.Wu@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://lore.kernel.org/r/20251113163348.137315-3-timur.kristof@gmail.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following warning that some users are reporting
with some kernel configurations:
"positional initialization of field in 'struct' declared
with 'designated_init' attribute"
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20251113163348.137315-2-timur.kristof@gmail.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Delete the attempt to progress the queue when checking if fence is
signaled. This avoids deadlock.
dma-fence_ops::signaled can be called with the fence lock in unknown
state. For radeon, the fence lock is also the wait queue lock. This can
cause a self deadlock when signaled() tries to make forward progress on
the wait queue. But advancing the queue is unneeded because incorrectly
returning false from signaled() is perfectly acceptable.
Link: https://github.com/brave/brave-browser/issues/49182
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4641
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Robert McClinton <rbmccav@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change comments from kernel-doc style "/**" to normal C comments
"/*" since the comments are not in kernel-doc format.
This fixes around 39 kernel-doc warnings like this one:
drivers/gpu/drm/amd/display/dc/core/dc_hw_sequencer.c:1322: warning:
This comment starts with '/**', but isn't a kernel-doc comment.
Refer Documentation/doc-guide/kernel-doc.rst
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202511062036.Ry8Z2APc-lkp@intel.com/
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following updates:
- Add interface to capture expected HW state from SW state
- Add panel Replay capability detection, DPCD reading, and enablement logic
- Re-check seamless boot enablement on subsequent dc_commit_streams
- Improve DPCD link capability retrieval with increased retries and per-retry delays
- Add HPD filter for HDMI
- Add pipe topology history tracking to DC
- Fix MST initialization on resume when switching from SST to MST during suspend
- Fix double cursor on DCN20 & DCN30 in non-native scaling
- Check DCCG_AUDIO_DTO2 register mask before access
- Fix pbn to kbps conversion
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Ignore Coverity false positive analysis in the dmub_cmd.h
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
