[ Upstream commit 9c02ea544a ]
The MAC can't facilitate WoL if the system can't go to sleep. Gate the
WoL support callbacks in ethtool at compile time using CONFIG_PM_SLEEP.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250909085849.3808169-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c7c19466c ]
The driver for the Rockchip MIPI CSI-2 DPHY uses GRF register offset
value 0 to sort out undefined registers. However, the RK3588 CSIDPHY GRF
this offset is perfectly fine (in fact, register 0 is the only one in
this register file).
Introduce a boolean variable to indicate valid registers and allow writes
to register 0.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Michael Riesch <michael.riesch@collabora.com>
Link: https://lore.kernel.org/r/20250616-rk3588-csi-dphy-v4-4-a4f340a7f0cf@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43bd2c4451 ]
Enable support for data lane rates between 80-160 Mbps cdns dphy
as mentioned in TRM [0] by setting the pll_opdiv field to 16.
This change enables lower resolutions like 640x480 at 60Hz.
[0]: https://www.ti.com/lit/zip/spruil1
(Table 12-552. DPHY_TX_PLL_CTRL Register Field Descriptions)
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Harikrishna Shenoy <h-shenoy@ti.com>
Link: https://lore.kernel.org/r/20250807052002.717807-1-h-shenoy@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e8011ffec ]
Since commit af153bb63a ("vfs: catch invalid modes in may_open()")
requires any inode be one of S_IFDIR/S_IFLNK/S_IFREG/S_IFCHR/S_IFBLK/
S_IFIFO/S_IFSOCK type, use S_IFREG for $Extend records.
Reported-by: syzbot <syzbot+895c23f6917da440ed0d@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=895c23f6917da440ed0d
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit deb105f498 ]
The 88e1510 PHY has an erratum where the phy downshift counter is not
cleared after phy being suspended(BMCR_PDOWN set) and then later
resumed(BMCR_PDOWN cleared). This can cause the gigabit link to
intermittently downshift to a lower speed.
Disabling and re-enabling the downshift feature clears the counter,
allowing the PHY to retry gigabit link negotiation up to the programmed
retry count times before downshifting. This behavior has been observed
on copper links.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250906-marvell_fix-v2-1-f6efb286937f@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10fb1b2fca ]
If two fault IRQs arrive in short succession recovery work will be
queued up twice.
When recovery runs a second time it may end up killing an unrelated
context.
Prevent this by masking off interrupts when triggering recovery.
Signed-off-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/670023/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87c5ff5615 ]
In the __cdnsp_gadget_init() and cdnsp_gadget_exit() functions, the gadget
structure (pdev->gadget) was freed before its endpoints.
The endpoints are linked via the ep_list in the gadget structure.
Freeing the gadget first leaves dangling pointers in the endpoint list.
When the endpoints are subsequently freed, this results in a use-after-free.
Fix:
By separating the usb_del_gadget_udc() operation into distinct "del" and
"put" steps, cdnsp_gadget_free_endpoints() can be executed prior to the
final release of the gadget structure with usb_put_gadget().
A patch similar to bb9c74a5bd14("usb: dwc3: gadget: Free gadget structure
only after freeing endpoints").
Signed-off-by: Chen Yufeng <chenyufeng@iie.ac.cn>
Link: https://lore.kernel.org/r/20250905094842.1232-1-chenyufeng@iie.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed6f727c57 ]
Set the hid req->zero flag of ep0/in_ep to true by default,
then the UDC drivers can transfer a zero length packet at
the end if the hid transfer with size divisible to EPs max
packet size according to the USB 2.0 spec.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/1756204087-26111-1-git-send-email-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9be15fbfc6 ]
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU command buffers and event buffer registers remain locked and
exclusive to the previous kernel. Attempts to enable command and event
buffers in the kdump kernel will fail, as hardware ignores writes to
the locked MMIO registers as per AMD IOMMU spec Section 2.12.2.1.
Skip enabling command buffers and event buffers for kdump boot as they
are already enabled in the previous kernel.
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Link: https://lore.kernel.org/r/576445eb4f168b467b0fc789079b650ca7c5b037.1756157913.git.ashish.kalra@amd.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21f82062d0 ]
An exchange with a NFC target must complete within NCI_DATA_TIMEOUT.
A delay of 700 ms is not sufficient for cryptographic operations on smart
cards. CardOS 6.0 may need up to 1.3 seconds to perform 256-bit ECDH
or 3072-bit RSA. To prevent brute-force attacks, passports and similar
documents introduce even longer delays into access control protocols
(BAC/PACE).
The timeout should be higher, but not too much. The expiration allows
us to detect that a NFC target has disappeared.
Signed-off-by: Juraj Šarinay <juraj@sarinay.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250902113630.62393-1-juraj@sarinay.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d95261eeb ]
In ipv6_rpl_srh_rcv() we use min(net->ipv6.devconf_all->rpl_seg_enabled,
idev->cnf.rpl_seg_enabled) is intended to return 0 when either value is
zero, but if one of the values is negative it will in fact return non-zero.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://patch.msgid.link/20250901123726.1972881-3-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ddcb0cb9d ]
Driver unconditionally saves current state on first init in
dsi_pll_7nm_init(), but does not save the VCO rate, only some of the
divider registers. The state is then restored during probe/enable via
msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() ->
dsi_7nm_pll_restore_state().
Restoring calls dsi_pll_7nm_vco_set_rate() with
pll_7nm->vco_current_rate=0, which basically overwrites existing rate of
VCO and messes with clock hierarchy, by setting frequency to 0 to clock
tree. This makes anyway little sense - VCO rate was not saved, so
should not be restored.
If PLL was not configured configure it to minimum rate to avoid glitches
and configuring entire in clock hierarchy to 0 Hz.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/657827/
Link: https://lore.kernel.org/r/20250610-b4-sm8750-display-v6-9-ee633e3ddbff@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b63f008f39 ]
According to Hardware Programming Guide for DSI PHY, the retime buffer
resync should be done after PLL clock users (byte_clk and intf_byte_clk)
are enabled. Downstream also does it as part of configuring the PLL.
Driver was only turning off the resync FIFO buffer, but never bringing it
on again.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/657823/
Link: https://lore.kernel.org/r/20250610-b4-sm8750-display-v6-6-ee633e3ddbff@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e742de97c ]
DMA Engine has support for the callback_result which provides
the status of the request and the residue. This helps in
determining the correct status of the request and in
efficient resource management of the request.
The 'callback_result' method is preferred over the deprecated
'callback' method.
Signed-off-by: Devendra K Verma <devverma@amd.com>
Link: https://lore.kernel.org/r/20250821121505.318179-1-devverma@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9a3e99294 ]
This patch modifies the type of setup_xref from void to int and handles
errors since the function can fail.
`setup_xref` now returns the (eventual) error from
`dmae_set_dmars`|`dmae_set_chcr`, while `shdma_tx_submit` handles the
result, removing the chunks from the queue and marking PM as idle in
case of an error.
Signed-off-by: Thomas Andreatta <thomas.andreatta2000@gmail.com>
Link: https://lore.kernel.org/r/20250827152442.90962-1-thomas.andreatta2000@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a8c02a6bf ]
Networking drivers implementing PTP clocks and kernel socket code
handling hardware timestamps use the 64-bit signed ktime_t type counting
nanoseconds. When a PTP clock reaches the maximum value in year 2262,
the timestamps returned to applications will overflow into year 1667.
The same thing happens when injecting a large offset with
clock_adjtime(ADJ_SETOFFSET).
The commit 7a8e61f847 ("timekeeping: Force upper bound for setting
CLOCK_REALTIME") limited the maximum accepted value setting the system
clock to 30 years before the maximum representable value (i.e. year
2232) to avoid the overflow, assuming the system will not run for more
than 30 years.
Enforce the same limit for PTP clocks. Don't allow negative values and
values closer than 30 years to the maximum value. Drivers may implement
an even lower limit if the hardware registers cannot represent the whole
interval between years 1970 and 2262 in the required resolution.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <jstultz@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250828103300.1387025-1-mlichvar@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bee3554d1a ]
Use int instead of u32 for 'ret' variable to store negative error codes
returned by PM8001_CHIP_DISP->set_nvmd_req().
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Link: https://lore.kernel.org/r/20250826093242.230344-1-rongqianfeng@vivo.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0d04fe6a6 ]
Bindig requires a node name matching ‘^gpio@[0-9a-f]+$’. This patch
changes the clock name from “stp” to “gpio”.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d66949a187 ]
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: pci@e105400 (lantiq,pci-xway): 'device_type' is a required property
from schema $id: http://devicetree.org/schemas/pci/pci-bus-common.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8dee66c37 ]
This fixes the following warnings:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpus: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/cpus.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpus: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/cpus.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpu@0 (mips,mips24Kc): 'reg' is a required property
from schema $id: http://devicetree.org/schemas/mips/cpus.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3820e9d35 ]
When KFD asks CP to preempt queues, other than preempt CP queues, CP
also requests SDMA to preempt SDMA queues with UNMAP_LATENCY timeout.
Currently queue_preemption_timeout_ms is 9000 ms by default but can be
configured via module parameter. KFD_UNMAP_LATENCY_MS is hard coded as
4000 ms though. This patch ties KFD_UNMAP_LATENCY_MS to
queue_preemption_timeout_ms so in a slow system such as emulator, both
CP and SDMA slowness are taken into account.
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78b6a991eb ]
Device can be unbound, so driver must also release memory for the wakeup
source. Do not use devm interface, because it would change the order of
cleanup.
Link: https://lore.kernel.org/lkml/20250501-device-wakeup-leak-extcon-v2-1-7af77802cbea@linaro.org/
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6477ee38c ]
Eliminate the use of static variables within the log pull implementation
to resolve a race condition and prevent data gaps when pulling logs from
multiple controllers in parallel, ensuring each operation is properly
isolated.
Signed-off-by: Francisco Gutierrez <frankramirez@google.com>
Link: https://lore.kernel.org/r/20250723183543.1443301-1-frankramirez@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829fa1582b ]
Firmware can enter a transient fault while creating operational queues.
The driver fails the load immediately.
Add a retry loop that checks controller status and history bit after
queue creation. If either indicates a fault, retry init up to a set
limit before failing.
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20250820084138.228471-3-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2aec0b6a6b ]
Just add fixed struct size validations for UAC2 and UAC3 effect
units. The descriptor has a variable-length array, so it should be
validated with a proper function later once when the unit is really
parsed and used by the driver (currently only referred partially for
the input terminal parsing).
Link: https://patch.msgid.link/20250821151751.12100-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6238784e50 ]
The error handling path in pci_p2pdma_add_resource() contains a bug in its
`pgmap_free` label.
Memory is allocated for the `p2p_pgmap` struct, and the pointer is stored
in `p2p_pgmap`. However, the error path calls devm_kfree() with `pgmap`,
which is a pointer to a member field within the `p2p_pgmap` struct, not the
base pointer of the allocation.
Correct the bug by passing the correct base pointer, `p2p_pgmap`, to
devm_kfree().
Signed-off-by: Sungho Kim <sungho.kim@furiosa.ai>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://patch.msgid.link/20250820105714.2939896-1-sungho.kim@furiosa.ai
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d85c565a7 ]
Initially, trace_sock_exceed_buf_limit() was invoked when
__sk_mem_raise_allocated() failed due to the memcg limit or the
global limit.
However, commit d6f19938eb ("net: expose sk wmem in
sock_exceed_buf_limit tracepoint") somehow suppressed the event
only when memcg failed to charge for SK_MEM_RECV, although the
memcg failure for SK_MEM_SEND still triggers the event.
Let's restore the event for SK_MEM_RECV.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev>
Link: https://patch.msgid.link/20250815201712.1745332-5-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0ac6d3b56 ]
When removing a nexthop, commit
90f33bffa3 ("nexthops: don't modify published nexthop groups") added a
call to synchronize_rcu() (later changed to _net()) to make sure
everyone sees the new nexthop-group before the rtnl-lock is released.
When one wants to delete a large number of groups and nexthops, it is
fastest to first flush the groups (ip nexthop flush groups) and then
flush the nexthops themselves (ip -6 nexthop flush). As that way the
groups don't need to be rebalanced.
However, `ip -6 nexthop flush` will still take a long time if there is
a very large number of nexthops because of the call to
synchronize_net(). Now, if there are no more groups, there is no point
in calling synchronize_net(). So, let's skip that entirely by checking
if nh->grp_list is empty.
This gives us a nice speedup:
BEFORE:
=======
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 2097152 nexthops
real 1m45.345s
user 0m0.001s
sys 0m0.005s
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 4194304 nexthops
real 3m10.430s
user 0m0.002s
sys 0m0.004s
AFTER:
======
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 2097152 nexthops
real 0m17.545s
user 0m0.003s
sys 0m0.003s
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 4194304 nexthops
real 0m35.823s
user 0m0.002s
sys 0m0.004s
Signed-off-by: Christoph Paasch <cpaasch@openai.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250816-nexthop_dump-v2-2-491da3462118@openai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ba0fb42aa ]
misc_open() may request module for miscdevice with dynamic minor, which
is meaningless since:
- The dynamic minor allocated is unknown in advance without registering
miscdevice firstly.
- Macro MODULE_ALIAS_MISCDEV() is not applicable for dynamic minor.
Fix by only requesting module for miscdevice with fixed minor.
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250714-rfc_miscdev-v6-6-2ed949665bde@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 956606bafb ]
This fix is already present in f_ecm.c and was never
propagated to f_ncm.c
When creating multiple NCM ethernet devices
on a composite usb gadget device
each MAC address on the HOST side will be identical.
Having the same MAC on different network interfaces is bad.
This fix updates the MAC address inside the
ncm_strings_defs global during the ncm_bind call.
This ensures each device has a unique MAC.
In f_ecm.c ecm_string_defs is updated in the same way.
The defunct MAC assignment in ncm_alloc has been removed.
Signed-off-by: raub camaioni <raubcameo@gmail.com>
Link: https://lore.kernel.org/r/20250815131358.1047525-1-raubcameo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d75c7021c0 ]
avg sample info is a bit field coded inside the following
bits: 5,6,7 and 8 of a device status register.
Channel num info the same, but over bits: 1, 2 and 3.
Mask both values in order to avoid touching other register bits,
since the first info (avg sample), came from DT.
Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250717221559.158872-1-rodrigo.gobbi.7@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb640b2ca5 ]
Detecting the monitor for DisplayPort targets is more complicated than
just reading the HPD pin level: it requires reading the DPCD in order to
check what kind of device is attached to the port and whether there is
an actual display attached.
In order to let DRM framework handle such configurations, disable
DRM_BRIDGE_OP_DETECT for dp-connector devices, letting the actual DP
driver perform detection. This still keeps DRM_BRIDGE_OP_HPD enabled, so
it is valid for the bridge to report HPD events.
Currently inside the kernel there are only two targets which list
hpd-gpios for dp-connector devices: arm64/qcom/qcs6490-rb3gen2 and
arm64/qcom/sa8295p-adp. Both should be fine with this change.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konradybcio@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250802-dp-conn-no-detect-v1-1-2748c2b946da@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eecd203ada ]
syzbot is reporting that imon has three problems which result in
hung tasks due to forever holding device lock [1].
First problem is that when usb_rx_callback_intf0() once got -EPROTO error
after ictx->dev_present_intf0 became true, usb_rx_callback_intf0()
resubmits urb after printk(), and resubmitted urb causes
usb_rx_callback_intf0() to again get -EPROTO error. This results in
printk() flooding (RCU stalls).
Alan Stern commented [2] that
In theory it's okay to resubmit _if_ the driver has a robust
error-recovery scheme (such as giving up after some fixed limit on the
number of errors or after some fixed time has elapsed, perhaps with a
time delay to prevent a flood of errors). Most drivers don't bother to
do this; they simply give up right away. This makes them more
vulnerable to short-term noise interference during USB transfers, but in
reality such interference is quite rare. There's nothing really wrong
with giving up right away.
but imon has a poor error-recovery scheme which just retries forever;
this behavior should be fixed.
Since I'm not sure whether it is safe for imon users to give up upon any
error code, this patch takes care of only union of error codes chosen from
modules in drivers/media/rc/ directory which handle -EPROTO error (i.e.
ir_toy, mceusb and igorplugusb).
Second problem is that when usb_rx_callback_intf0() once got -EPROTO error
before ictx->dev_present_intf0 becomes true, usb_rx_callback_intf0() always
resubmits urb due to commit 8791d63af0 ("[media] imon: don't wedge
hardware after early callbacks"). Move the ictx->dev_present_intf0 test
introduced by commit 6f6b90c923 ("[media] imon: don't parse scancodes
until intf configured") to immediately before imon_incoming_packet(), or
the first problem explained above happens without printk() flooding (i.e.
hung task).
Third problem is that when usb_rx_callback_intf0() is not called for some
reason (e.g. flaky hardware; the reproducer for this problem sometimes
prevents usb_rx_callback_intf0() from being called),
wait_for_completion_interruptible() in send_packet() never returns (i.e.
hung task). As a workaround for such situation, change send_packet() to
wait for completion with timeout of 10 seconds.
Link: https://syzkaller.appspot.com/bug?extid=592e2ab8775dbe0bf09a [1]
Link: https://lkml.kernel.org/r/d6da6709-d799-4be3-a695-850bddd6eb24@rowland.harvard.edu [2]
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2327a3d6f6 ]
Fix field-spanning memcpy warnings in ah6_output() and
ah6_output_done() where extension headers are copied to/from IPv6
address fields, triggering fortify-string warnings about writes beyond
the 16-byte address fields.
memcpy: detected field-spanning write (size 40) of single field "&top_iph->saddr" at net/ipv6/ah6.c:439 (size 16)
WARNING: CPU: 0 PID: 8838 at net/ipv6/ah6.c:439 ah6_output+0xe7e/0x14e0 net/ipv6/ah6.c:439
The warnings are false positives as the extension headers are
intentionally placed after the IPv6 header in memory. Fix by properly
copying addresses and extension headers separately, and introduce
helper functions to avoid code duplication.
Reported-by: syzbot+01b0667934cdceb4451c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=01b0667934cdceb4451c
Signed-off-by: Charalampos Mitrodimas <charmitro@posteo.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d05b24429 ]
If a backup port is configured for a bridge port, the bridge will
redirect known unicast traffic towards the backup port when the primary
port is administratively up but without a carrier. This is useful, for
example, in MLAG configurations where a system is connected to two
switches and there is a peer link between both switches. The peer link
serves as the backup port in case one of the switches loses its
connection to the multi-homed system.
In order to avoid flooding when the primary port loses its carrier, the
bridge does not flush dynamic FDB entries pointing to the port upon STP
disablement, if the port has a backup port.
The above means that known unicast traffic destined to the primary port
will be blackholed when the port is put administratively down, until the
FDB entries pointing to it are aged-out.
Given that the current behavior is quite weird and unlikely to be
depended on by anyone, amend the bridge to redirect to the backup port
also when the primary port is administratively down and not only when it
does not have a carrier.
The change is motivated by a report from a user who expected traffic to
be redirected to the backup port when the primary port was put
administratively down while debugging a network issue.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20250812080213.325298-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 704e5dd1c0 ]
Ever since uevent support was added for AER and EEH with commit
856e1eb9bd ("PCI/AER: Add uevents in AER and EEH error/resume"), it
reported PCI_ERS_RESULT_NONE as uevent when recovery begins.
Commit 7b42d97e99 ("PCI/ERR: Always report current recovery status for
udev") subsequently amended AER to report the actual return value of
error_detected().
Make the same change to EEH to align it with AER and s390.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/linux-pci/aIp6LiKJor9KLVpv@wunner.de/
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Link: https://patch.msgid.link/20250807-add_err_uevents-v5-3-adf85b0620b0@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d03847175 ]
The thunderbolt driver sets up device link dependencies from hotplug ports
to the Host Router (aka Native Host Interface, NHI). When resuming from
system sleep, this allows the Host Router to re-establish tunnels to
attached Thunderbolt devices before the hotplug ports resume.
To identify the hotplug ports, the driver utilizes the is_hotplug_bridge
flag which also encompasses ACPI slots handled by the ACPI hotplug driver.
Thunderbolt hotplug ports are always Hot-Plug Capable PCIe ports, so it is
more apt to identify them with the is_pciehp flag.
Similarly, hotplug ports on older Thunderbolt controllers have broken MSI
support and are quirked to use legacy INTx interrupts instead. The quirk
identifies them with is_hotplug_bridge, even though all affected ports are
also matched by is_pciehp. So use is_pciehp here as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6896c2449a ]
stmmac_hw_setup() may return 0 on success and an appropriate negative
integer as defined in errno.h file on failure, just check it and then
return early if failed in stmmac_resume().
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/20250811073506.27513-2-yangtiezhu@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ba38a7a9a ]
emulate_vsyscall() expects to see X86_PF_INSTR in PFEC on a vsyscall
page fault, but the CPU does not report X86_PF_INSTR if neither
X86_FEATURE_NX nor X86_FEATURE_SMEP are enabled.
X86_FEATURE_NX should be enabled on nearly all 64-bit CPUs, except for
early P4 processors that did not support this feature.
Instead of explicitly checking for X86_PF_INSTR, compare the fault
address to RIP.
On machines with X86_FEATURE_NX enabled, issue a warning if RIP is equal
to fault address but X86_PF_INSTR is absent.
[ dhansen: flesh out code comments ]
Originally-by: Dave Hansen <dave.hansen@intel.com>
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Link: https://lore.kernel.org/all/bd81a98b-f8d4-4304-ac55-d4151a1a77ab@intel.com
Link: https://lore.kernel.org/all/20250624145918.2720487-1-kirill.shutemov%40linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfb29225db ]
TIDSS uses crtc_* fields to propagate its registers and set the
clock rates. So set the CRTC modesetting timing parameters with
the adjusted mode when needed, to set correct values.
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20250624080402.302526-1-j-choudhary@ti.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 478306edc2 ]
Use the crtc_* fields from drm_display_mode, instead of the "logical"
fields. This shouldn't change anything in practice, but afaiu the crtc_*
fields are the correct ones to use here.
Reviewed-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250723-cdns-dsi-impro-v5-3-e61cc06074c2@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc6e8d1cce ]
The ivtv driver has a structure named ivtv_open_id that models an open
file handle for the device. It embeds a v4l2_fh instance for file
handles that correspond to a V4L2 video device, and stores a pointer to
that v4l2_fh in struct ivtv_stream to identify which open file handle
owns a particular stream.
In addition to video devices, streams can be owned by ALSA PCM devices.
Those devices do not make use of the v4l2_fh instance for obvious
reasons, but the snd_ivtv_pcm_capture_open() function still initializes
a "fake" v4l2_fh for the sole purpose of using it as an open file handle
identifier. The v4l2_fh is not properly destroyed when the ALSA PCM
device is closed, leading to possible resource leaks.
Fortunately, the v4l2_fh instance pointed to by ivtv_stream is not
accessed, only the pointer value is used for comparison. Replace it with
a pointer to the ivtv_open_id structure that embeds the v4l2_fh, and
don't initialize the v4l2_fh for ALSA PCM devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57af162bfc ]
Some kfd ioctls may not be available depending on the kernel version the
user is running, as such we need to report -ENOTTY so userland can
determine the cause of the ioctl failure.
Signed-off-by: Geoffrey McRae <geoffrey.mcrae@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc4c0a48bd ]
The get_next_frame() function in psock_tpacket.c was missing a return
statement in its default switch case, leading to a compiler warning.
This was caused by a `bug_on(1)` call, which is defined as an
`assert()`, being compiled out because NDEBUG is defined during the
build.
Instead of adding a `return NULL;` which would silently hide the error
and could lead to crashes later, this change restores the original
author's intent. By adding `#undef NDEBUG` before including <assert.h>,
we ensure the assertion is active and will cause the test to abort if
this unreachable code is ever executed.
Signed-off-by: Wake Liu <wakel@google.com>
Link: https://patch.msgid.link/20250809062013.2407822-1-wakel@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c36748e873 ]
The `__WORDSIZE` macro, defined in the non-standard `<bits/wordsize.h>`
header, is a GNU extension and not universally available with all
toolchains, such as Clang when used with musl libc.
This can lead to build failures in environments where this header is
missing.
The intention of the code is to determine the bit width of a C `long`.
Replace the non-portable `__WORDSIZE` with the standard and portable
`sizeof(long) * 8` expression to achieve the same result.
This change also removes the inclusion of the now-unused
`<bits/wordsize.h>` header.
Signed-off-by: Wake Liu <wakel@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebc7086b39 ]
RDC PCI to PCIe bridges, present on Vortex86DX3 and Vortex86EX2 SoCs, do
not support MSIs. If enabled, interrupts generated by PCIe devices never
reach the processor.
I have contacted the manufacturer (DM&P) and they confirmed that PCI MSIs
need to be disabled for them.
Signed-off-by: Marcos Del Sol Vives <marcos@orca.pet>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250705233209.721507-1-marcos@orca.pet
Signed-off-by: Sasha Levin <sashal@kernel.org>
