commit 227a4fd801 upstream.
When a device with an isochronous endpoint is plugged into the Intel
xHCI host controller, and the driver submits multiple frames per URB,
the xHCI driver will set the Block Event Interrupt (BEI) flag on all
but the last TD for the URB. This causes the host controller to place
an event on the event ring, but not send an interrupt. When the last
TD for the URB completes, BEI is cleared, and we get an interrupt for
the whole URB.
However, under Intel xHCI host controllers, if the event ring is full
of events from transfers with BEI set, an "Event Ring is Full" event
will be posted to the last entry of the event ring, but no interrupt
is generated. Host will cease all transfer and command executions and
wait until software completes handling the pending events in the event
ring. That means xHC stops, but event of "event ring is full" is not
notified. As the result, the xHC looks like dead to user.
This patch is to apply XHCI_AVOID_BEI quirk to Intel xHC devices. And
it should be backported to kernels as old as 3.0, that contains the
commit 69e848c209 ("Intel xhci: Support EHCI/xHCI port switching.").
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Alistair Grant <akgrant0710@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9425183d17 upstream.
Linux xHCI driver doesn't report and handle port cofig error change.
If Port Configure Error for root hub port occurs, CEC bit in PORTSC
would be set by xHC and remains 1. This happends when the root port
fails to configure its link partner, e.g. the port fails to exchange
port capabilities information using Port Capability LMPs.
Then the Port Status Change Events will be blocked until all status
change bits(CEC is one of the change bits) are cleared('0') (refer to
xHCI spec 4.19.2). Otherwise, the port status change event for this
root port will not be generated anymore, then root port would look
like dead for user and can't be recovered until a Host Controller
Reset(HCRST).
This patch is to check CEC bit in PORTSC in xhci_get_port_status()
and set a Config Error in the return status if CEC is set. This will
cause a ClearPortFeature request, where CEC bit is cleared in
xhci_clear_port_change_bit().
[The commit log is based on initial Marvell patch posted at
http://marc.info/?l=linux-kernel&m=142323612321434&w=2]
Reported-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45ba2154d1 upstream.
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6596a926b0 upstream.
Include the high order bit fields for Max scratchpad buffers when
calculating how many scratchpad buffers are needed.
I'm suprised this hasn't caused more issues, we never allocated more than
32 buffers even if xhci needed more. Either we got lucky and xhci never
really used past that area, or then we got enough zeroed dma memory anyway.
Should be backported as far back as possible
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d89252a99 upstream.
Commit c3ee9b76aa (EHCI: improved logic for isochronous scheduling)
introduced the idea of using ehci->last_iso_frame as the origin (or
base) for the circular calculations involved in modifying the
isochronous schedule. However, the new code it added used
ehci->last_iso_frame before the value was properly initialized. This
patch rectifies the mistake by moving the initialization lines earlier
in iso_stream_schedule().
This fixes Bugzilla #72891.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: c3ee9b76aa
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Tested-by: Joe Bryant <tenminjoe@yahoo.com>
Tested-by: Martin Long <martin@longhome.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56abcab833 upstream.
Commit 8dccddbc23 ("OHCI: final fix for NVIDIA problems (I hope)")
introduced into 3.1.9 broke boot on e.g. Freescale P2020DS development
board. The code path that was previously specific to NVIDIA controllers
had then become taken for all chips.
However, the M5237 installed on the board wedges solid when accessing
its base+OHCI_FMINTERVAL register, making it impossible to boot any
kernel newer than 3.1.8 on this particular and apparently other similar
machines.
Don't readl() and writel() base+OHCI_FMINTERVAL on PCI ID 10b9:5237.
The patch is suitable for the -next tree as well as all maintained
kernels up to 3.2 inclusive.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e71a322fd upstream.
If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.
Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.
Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.
Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.)
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1377e5397 upstream.
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit ff8cbf250b ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3492dbfa1 upstream.
A halted endpoint ring must first be reset, then move the ring
dequeue pointer past the problematic TRB. If we start the ring too
early after reset, but before moving the dequeue pointer we
will end up executing the same problematic TRB again.
As we always issue a set transfer dequeue command after a reset
endpoint command we can skip starting endpoint rings at reset endpoint
command completion.
Without this fix we end up trying to handle the same faulty TD for
contol endpoints. causing timeout, and failing testusb ctrl_out write
tests.
Fixes: e9df17e (USB: xhci: Correct assumptions about number of rings per endpoint.)
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7312b5ddd4 upstream.
Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH. This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.
But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed. Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.
Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96044694b8 upstream.
Resuming from hibernate (S4) will restart and re-initialize xHC.
The device contexts are freed and will be re-allocated later during device reset.
Usb core will disable link pm in device resume before device reset, which will
try to change the max exit latency, accessing the device contexts before they are re-allocated.
There is no need to zero (disable) the max exit latency when disabling hw lpm
for a freshly re-initialized xHC. So check that device context exists before
doing anything. The max exit latency will be set again after device reset when usb core
enables the link pm.
Reported-by: Imre Deak <imre.deak@intel.com>
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c207e7c50f upstream.
If xhci initialization fails before the roothub bandwidth
domains (xhci->rh_bw[i]) are allocated it will oops when
trying to access rh_bw members in xhci_mem_cleanup().
Reported-by: Manuel Reimer <manuel.reimer@gmx.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96908589a8 upstream.
Commit 71c731a (usb: host: xhci: Fix Compliance Mode
on SN65LVP3502CP Hardware) implemented a workaround
for a known issue with Texas Instruments' USB 3.0
redriver IC but it left a condition where any xHCI
host would be taken out of reset if port was placed
in compliance mode and there was no device connected
to the port.
That condition would trigger a fake connection to a
non-existent device so that usbcore would trigger a
warm reset of the port, thus taking the link out of
reset.
This has the side-effect of preventing any xHCI host
connected to a Linux machine from starting and running
the USB 3.0 Electrical Compliance Suite because the
port will mysteriously taken out of compliance mode
and, thus, xHCI won't step through the necessary
compliance patterns for link validation.
This patch fixes the issue by just adding a missing
check for XHCI_COMP_MODE_QUIRK inside
xhci_hub_report_usb3_link_state() when PORT_CAS isn't
set.
This patch should be backported to all kernels containing
commit 71c731a.
Fixes: 71c731a (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware)
Cc: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cbcc35e5b upstream.
The roothub's index per controller is from 0, but the hub port index per hub
is from 1, this patch fixes "can't find device at roohub" problem for connecting
test fixture at roohub when do USB-IF Embedded Host High-Speed Electrical Test.
This patch is for v3.12+.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a54886342 upstream.
When using a Renesas uPD720231 chipset usb-3 uas to sata bridge with a 120G
Crucial M500 ssd, model string: Crucial_ CT120M500SSD1, together with a
the integrated Intel xhci controller on a Haswell laptop:
00:14.0 USB controller [0c03]: Intel Corporation 8 Series USB xHCI HC [8086:9c31] (rev 04)
The following error gets logged to dmesg:
xhci error: Transfer event TRB DMA ptr not part of current TD
Treating COMP_STOP the same as COMP_STOP_INVAL when no event_seg gets found
fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e693739e9 upstream.
The EHCI packet buffer in/out threshold is programmable for Intel Quark X1000
USB host controller, and the default value is 0x20 dwords. The in/out threshold
can be programmed to 0x80 dwords (512 Bytes) to maximize the perfomrance,
but only when isochronous/interrupt transactions are not initiated by the USB
host controller. This patch is to reconfigure the packet buffer in/out
threshold as maximal as possible to maximize the performance, and 0x7F dwords
(508 Bytes) should be used because the USB host controller initiates
isochronous/interrupt transactions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@intel.com>
Signed-off-by: Alvin (Weike) Chen <alvin.chen@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 977dcfdc60 upstream.
This patch fixes a bug in ohci-hcd. When an URB is unlinked, the
corresponding Endpoint Descriptor is added to the ed_rm_list and taken
off the hardware schedule. Once the ED is no longer visible to the
hardware, finish_unlinks() handles the URBs that were unlinked or have
completed. If any URBs remain attached to the ED, the ED is added
back to the hardware schedule -- but only if the controller is
running.
This fails when a controller dies. A non-empty ED does not get added
back to the hardware schedule and does not remain on the ed_rm_list;
ohci-hcd loses track of it. The remaining URBs cannot be unlinked,
which causes the USB stack to hang.
The patch changes finish_unlinks() so that non-empty EDs remain on
the ed_rm_list if the controller isn't running. This requires moving
some of the existing code around, to avoid modifying the ED's hardware
fields more than once.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 256dbcd80f upstream.
The debug routine fill_async_buffer() in ohci-hcd is buggy: It never
produces any output because it forgets to initialize the output buffer
size. Also, the debug routine ohci_dump() has an unused argument.
This patch adds the correct initialization and removes the unused
argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6236f6d1d upstream.
The system suspend flow as following:
1, Freeze all user processes and kenrel threads.
2, Try to suspend all devices.
2.1, If pci device is in RPM suspended state, then pci driver will try
to resume it to RPM active state in the prepare stage.
2.2, xhci_resume function calls usb_hcd_resume_root_hub to queue two
workqueue items to resume usb2&usb3 roothub devices.
2.3, Call suspend callbacks of devices.
2.3.1, All suspend callbacks of all hcd's children, including
roothub devices are called.
2.3.2, Finally, hcd_pci_suspend callback is called.
Due to workqueue threads were already frozen in step 1, the workqueue
items can't be scheduled, and the roothub devices can't be resumed in
this flow. The HCD_FLAG_WAKEUP_PENDING flag which is set in
usb_hcd_resume_root_hub won't be cleared. Finally,
hcd_pci_suspend will return -EBUSY, and system suspend fails.
The reason why this issue doesn't show up very often is due to that
choose_wakeup will be called in step 2.3.1. In step 2.3.1, if
udev->do_remote_wakeup is not equal to device_may_wakeup(&udev->dev), then
udev will resume to RPM active for changing the wakeup settings. This
has been a lucky hit which hides this issue.
For some special xHCI controllers which have no USB2 port, then roothub
will not match hub driver due to probe failed. Then its
do_remote_wakeup will be set to zero, and we won't be as lucky.
xhci driver doesn't need to resume roothub devices everytime like in
the above case. It's only needed when there are pending event TRBs.
This patch should be back-ported to kernels as old as 3.2, that
contains the commit f69e3120df
"USB: XHCI: resume root hubs when the controller resumes"
Signed-off-by: Wang, Yu <yu.y.wang@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[use readl() instead of removed xhci_readl(), reword commit message -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3213b15138 upstream.
The transfer burst count (TBC) field in xhci 1.0 hosts should be set
to the number of bursts needed to transfer all packets in a isoc TD.
Supported values are 0-2 (1 to 3 bursts per service interval).
Formula for TBC calculation is given in xhci spec section 4.11.2.3:
TBC = roundup( Transfer Descriptor Packet Count / Max Burst Size +1 ) - 1
This patch should be applied to stable kernels since 3.0 that contain
the commit 5cd43e33b9
"xhci 1.0: Set transfer burst count field."
Suggested-by: ShiChun Ma <masc2008@qq.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fcfb0d682 upstream.
Command completion events normally include command completion status,
SLOT_ID, and a pointer to the original command. Reset device command
completion SLOT_ID may be zero according to xhci specs 4.6.11.
VIA controllers set the SLOT_ID to zero, triggering a WARN_ON in the
command completion handler.
Use the SLOT ID found from the original command instead.
This patch should be applied to stable kernels since 3.13 that contain
the commit 20e7acb13f
"xhci: use completion event's slot id rather than dig it out of command"
Reported-by: Saran Neti <sarannmr@gmail.com>
Tested-by: Saran Neti <sarannmr@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0a50e92bd upstream.
Leandro Liptak reports that his HASEE E200 computer hangs when we ask
the BIOS to hand over control of the EHCI host controller. This
definitely sounds like a bug in the BIOS, but at the moment there is
no way to fix it.
This patch works around the problem by avoiding the handoff whenever
the motherboard and BIOS version match those of Leandro's computer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Leandro Liptak <leandroliptak@gmail.com>
Tested-by: Leandro Liptak <leandroliptak@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b38f09ccc3 upstream.
Sony VAIO t-series machines are not capable of switching usb2 ports over
from Intel EHCI to xHCI controller. If tried the USB2 port will be left
unconnected and unusable.
This patch should be backported to stable kernels as old as 3.12,
that contain the commit 26b76798e0
"Intel xhci: refactor EHCI/xHCI port switching"
Reported-by: Jorge <xxopxe@gmail.com>
Tested-by: Jorge <xxopxe@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5dc2808c47 upstream.
Lists of endpoints are stored for bandwidth calculation for roothub ports.
Make sure we remove all endpoints from the list before the whole device,
containing its endpoints list_head stuctures, is freed.
This used to be done in the wrong order in xhci_mem_cleanup(),
and triggered an oops in resume from S4 (hibernate).
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1db30a2a7 upstream.
Some OHCI controllers from ATI/AMD seem to have difficulty with
"global" USB suspend, that is, suspending an entire USB bus without
setting the suspend feature for each port connected to a device. When
we try to resume the child devices, the controller gives timeout
errors on the unsuspended ports, requiring resets, and can even cause
ohci-hcd to hang; see
http://marc.info/?l=linux-usb&m=139514332820398&w=2
and the following messages.
This patch fixes the problem by adding a new quirk flag to ohci-hcd.
The flag causes the ohci_rh_suspend() routine to suspend each
unsuspended, enabled port before suspending the root hub. This
effectively converts the "global" suspend to an ordinary root-hub
suspend. There is no need to unsuspend these ports when the root hub
is resumed, because the child devices will be resumed anyway in the
course of a normal system resume ("global" suspend is never used for
runtime PM).
This patch should be applied to all stable kernels which include
commit 0aa2832dd0 (USB: use "global suspend" for system sleep on
USB-2 buses) or a backported version thereof.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Peter Münster <pmlists@free.fr>
Tested-by: Peter Münster <pmlists@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d183c81929 upstream.
Per reference manuals of Freescale P1020 and P2020 SoCs, USB controller
present in these SoCs has bit 17 of USBx_CONTROL register marked as
Reserved - there is no PHY_CLK_VALID bit there.
Testing for this bit in ehci_fsl_setup_phy() behaves differently on two
P1020RDB boards available here - on one board test passes and fsl-usb
init succeeds, but on other board test fails, causing fsl-usb init to
fail.
This patch changes ehci_fsl_setup_phy() not to test PHY_CLK_VALID on
controller version 1.6 that (per manual) does not have this bit.
Signed-off-by: Nikita Yushchenko <nyushchenko@dev.rtsoft.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f2fe2d274 upstream.
To avoid memory fetch underflows with larger USB transfers, Tegra SoCs
need txfill_tuning's txfifothresh register field set to a non-default
value. Add a custom reset override in order to set this up.
These values are recommended practice for all Tegra chips. However,
I've only noticed practical problems when not setting them this way on
systems using Tegra124. Hence, CC: stable only for recent kernels which
actually support Tegra124.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f81b6d22a upstream.
We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.
The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.
This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.
This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae63674714 "USB: xhci: URB
cancellation support."
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01bb59ebff upstream.
When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
warning:
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]
Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.
This warning has been in since 3.2 kernel and was
caused by commit 421aa841a1
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c09ec25d36 upstream.
The same issue like with Panther Point chipsets. If the USB ports are
switched to xHCI on shutdown, the xHCI host will send a spurious interrupt,
which will wake the system. Some BIOS have work around for this, but not all.
One example is Compulab's mini-desktop, the Intense-PC2.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.
This patch should be backported to stable kernels as old as 3.12,
that contain the commit 638298dc66
"xhci: Fix spurious wakeups after S5 on Haswell"
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcffae7708 upstream.
xHCI driver has its own pci probe function that will call usb_hcd_pci_probe
to register its usb-2 bus, and then continue to manually register the
usb-3 bus. usb_hcd_pci_probe does a pm_runtime_put_noidle at the end and
might thus trigger a runtime suspend before the usb-3 bus is ready.
Prevent the runtime suspend by increasing the usage count in the
beginning of xhci_pci_probe, and decrease it once the usb-3 bus is
ready.
xhci-platform driver is not using usb_hcd_pci_probe to set up
busses and should not need to have it's usage count increased during probe.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 247bf55727.
This commit, together with commit 3804fad454
"USBNET: ax88179_178a: enable tso if usb host supports sg dma" were
origially added to get xHCI 1.0 hosts and usb ethernet ax88179_178a devices
working together with scatter gather. xHCI 1.0 hosts pose some requirement on how transfer
buffers are aligned, setting this requirement for 1.0 hosts caused USB 3.0 mass
storage devices to fail more frequently.
USB 3.0 mass storage devices used to work before 3.14-rc1. Theoretically,
the TD fragment rules could have caused an occasional disk glitch.
Now the devices *will* fail, instead of theoretically failing.
>From a user perspective, this looks like a regression; the USB device obviously
fails on 3.14-rc1, and may sometimes silently fail on prior kernels.
The proper soluition is to implement the TD fragment rules required, but for now
this patch needs to be reverted to get USB 3.0 mass storage devices working at the
level they used to.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci_irq() and ehci_hrtimer_func() can deadlock on ehci->lock when
threadirqs option is used. To prevent the deadlock use
spin_lock_irqsave() in ehci_irq().
This change can be reverted when hrtimer callbacks become threaded.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
High-speed USB connections revert back to full-speed signalling when
the device goes into suspend. This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.
On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state. It generates a false wakeup signal,
which can prevent the controller from going to sleep.
To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling. (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <Peter.Chen@freescale.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 35773dac5f. It's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. Commit 70cabb7d992f "xhci 1.0: Limit
arbitrarily-aligned scatter gather." should fix the issues seen with the
ax88179_178a driver on xHCI 1.0 hosts, without causing regressions.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12
This reverts commit d6c9ea9069.
We are ripping out commit 35773dac5f "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. This commit attempted to fix the
issues with that patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12
This reverts commit f2d9b991c5.
We are ripping out commit 35773dac5f "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. This commit attempted to fix the
issues with that patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org #3.12
xHCI 1.0 hosts have a set of requirements on how to align transfer
buffers on the endpoint rings called "TD fragment" rules. When the
ax88179_178a driver added support for scatter gather in 3.12, with
commit 804fad45411b48233b48003e33a78f290d227c8 "USBNET: ax88179_178a:
enable tso if usb host supports sg dma", it broke the device under xHCI
1.0 hosts. Under certain network loads, the device would see an
unexpected short packet from the host, which would cause the device to
stop sending ethernet packets, even through USB packets would still be
sent.
Commit 35773dac5f "usb: xhci: Link TRB must not occur within a USB
payload burst" attempted to fix this. It was a quick hack to partially
implement the TD fragment rules. However, it caused regressions in the
usb-storage layer and userspace USB drivers using libusb. The patches
to attempt to fix this are too far reaching into the USB core, and we
really need to implement the TD fragment rules correctly in the xHCI
driver, instead of continuing to wallpaper over the issues.
Disable arbitrarily-aligned scatter-gather in the xHCI driver for 1.0
hosts. Only the ax88179_178a driver checks the no_sg_constraint flag,
so don't set it for 1.0 hosts. This should not impact usb-storage or
usbfs behavior, since they pass down max packet sized aligned sg-list
entries (512 for USB 2.0 and 1024 for USB 3.0).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Mark Lord <mlord@pobox.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org # 3.12
Hi Greg,
Here's four patches for 3.14.
One of them adds an xHCI host quirk, and the other three of them fix
regressions introduced in 3.14. One regression causes USB 3.0 Link PM to
be enabled on all xHCI hosts (even those that may not support it), which
causes some USB 3.0 devices to not enumerate. A second regression causes
some xHCI hosts that don't support 64-bit addressing to stop responding to
commands and die.
Note, these patches don't fix the recent usbfs regression that was caused
by commit 35773dac5f "usb: xhci: Link TRB
must not occur within a USB payload burst". I'm waiting for those patches
to be tested.
Please pull usb-linus into usb-next, as I have feature patches that rely on
140e3026a5 Revert "usbcore: set lpm_capable field for LPM capable root
hubs"
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=sPwW
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2014-02-04' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Fix some regressions introduced in 3.14.
Hi Greg,
Here's four patches for 3.14.
One of them adds an xHCI host quirk, and the other three of them fix
regressions introduced in 3.14. One regression causes USB 3.0 Link PM to
be enabled on all xHCI hosts (even those that may not support it), which
causes some USB 3.0 devices to not enumerate. A second regression causes
some xHCI hosts that don't support 64-bit addressing to stop responding to
commands and die.
Note, these patches don't fix the recent usbfs regression that was caused
by commit 35773dac5f "usb: xhci: Link TRB
must not occur within a USB payload burst". I'm waiting for those patches
to be tested.
Please pull usb-linus into usb-next, as I have feature patches that rely on
140e3026a5 Revert "usbcore: set lpm_capable field for LPM capable root
hubs"
Sarah Sharp
This reverts commit e8b373326d. Many xHCI
host controllers can only handle 32-bit addresses, and writing 64-bits
at a time causes them to fail. Reading 64-bits at a time may also cause
them to return 0xffffffff, so revert this commit as well.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This reverts commit 7dd09a1af2.
Many xHCI host controllers can only handle 32-bit addresses, and writing
64-bits at a time causes them to fail. Rafał reports that USB devices
simply do not enumerate, and reverting this patch helps. Branimir
reports that his host controller doesn't respond to an Enable Slot
command and dies:
[ 75.576160] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 88.991634] xhci_hcd 0000:03:00.0: Stopped the command ring failed, maybe the host is dead
[ 88.991748] xhci_hcd 0000:03:00.0: Abort command ring failed
[ 88.991845] xhci_hcd 0000:03:00.0: HC died; cleaning up
[ 93.985489] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 93.985494] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[ 98.982586] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 98.982591] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[ 103.979696] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 103.979702] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Reported-by: Branimir Maksimovic <branimir.maksimovic@gmail.com>
Cc: Xenia Ragiadakou <burzalodowa@gmail.com>
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
Don Zickus <dzickus@redhat.com> writes:
Some co-workers of mine bought Samsung laptops that had mostly usb3 ports.
Those ports did not resume correctly (the driver would timeout communicating
and fail). This led to frustration as suspend/resume is a common use for
laptops.
Poking around, I applied the reset on resume quirk to this chipset and the
resume started working. Reloading the xhci_hcd module had been the temporary
workaround.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable # 2.6.37
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement a special ehci_write
for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2
Without this patcheset, imx28 works unstable at high AHB bus loading.
If the bus loading is not high, the imx28 usb can work well at the most
of time. There is a IC errata for this problem, usually, we consider
IC errata is a problem not a new feature, and this workaround is needed
for that, so we need to add them to stable tree 3.11+.
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
after device tree based clock lookup became available, the peripheral
driver need no longer construct clock names which include the component
index -- remove the "usb%d_clk" template, always use "ipg" instead
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
