commit db29a9508a upstream.
Given following iptables ruleset:
-P FORWARD DROP
-A FORWARD -m sctp --dport 9 -j ACCEPT
-A FORWARD -p tcp --dport 80 -j ACCEPT
-A FORWARD -p tcp -m conntrack -m state ESTABLISHED,RELATED -j ACCEPT
One would assume that this allows SCTP on port 9 and TCP on port 80.
Unfortunately, if the SCTP conntrack module is not loaded, this allows
*all* SCTP communication, to pass though, i.e. -p sctp -j ACCEPT,
which we think is a security issue.
This is because on the first SCTP packet on port 9, we create a dummy
"generic l4" conntrack entry without any port information (since
conntrack doesn't know how to extract this information).
All subsequent packets that are unknown will then be in established
state since they will fallback to proto_generic and will match the
'generic' entry.
Our originally proposed version [1] completely disabled generic protocol
tracking, but Jozsef suggests to not track protocols for which a more
suitable helper is available, hence we now mitigate the issue for in
tree known ct protocol helpers only, so that at least NAT and direction
information will still be preserved for others.
[1] http://www.spinics.net/lists/netfilter-devel/msg33430.html
Joint work with Daniel Borkmann.
Fixes CVE-2014-8160.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Zhiqiang Zhang <zhangzhiqiang.zhang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b50edd7812 ]
I noticed tcpdump was giving funky timestamps for locally
generated SYNACK messages on loopback interface.
11:42:46.938990 IP 127.0.0.1.48245 > 127.0.0.2.23850: S
945476042:945476042(0) win 43690 <mss 65495,nop,nop,sackOK,nop,wscale 7>
20:28:58.502209 IP 127.0.0.2.23850 > 127.0.0.1.48245: S
3160535375:3160535375(0) ack 945476043 win 43690 <mss
65495,nop,nop,sackOK,nop,wscale 7>
This is because we need to clear skb->tstamp before
entering lower stack, otherwise net_timestamp_check()
does not set skb->tstamp.
Fixes: 7faee5c0d5 ("tcp: remove TCP_SKB_CB(skb)->when")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f60e5990d9 ]
We should not consult skb->sk for output decisions in xmit recursion
levels > 0 in the stack. Otherwise local socket settings could influence
the result of e.g. tunnel encapsulation process.
ipv6 does not conform with this in three places:
1) ip6_fragment: we do consult ipv6_npinfo for frag_size
2) sk_mc_loop in ipv6 uses skb->sk and checks if we should
loop the packet back to the local socket
3) ip6_skb_dst_mtu could query the settings from the user socket and
force a wrong MTU
Furthermore:
In sk_mc_loop we could potentially land in WARN_ON(1) if we use a
PF_PACKET socket ontop of an IPv6-backed vxlan device.
Reuse xmit_recursion as we are currently only interested in protecting
tunnel devices.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 666b805150 ]
On processing cumulative ACKs, the FRTO code was not checking the
SACKed bit, meaning that there could be a spurious FRTO undo on a
cumulative ACK of a previously SACKed skb.
The FRTO code should only consider a cumulative ACK to indicate that
an original/unretransmitted skb is newly ACKed if the skb was not yet
SACKed.
The effect of the spurious FRTO undo would typically be to make the
connection think that all previously-sent packets were in flight when
they really weren't, leading to a stall and an RTO.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Fixes: e33099f96d ("tcp: implement RFC5682 F-RTO")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6fd99094de ]
A local route may have a lower hop_limit set than global routes do.
RFC 3756, Section 4.2.7, "Parameter Spoofing"
> 1. The attacker includes a Current Hop Limit of one or another small
> number which the attacker knows will cause legitimate packets to
> be dropped before they reach their destination.
> As an example, one possible approach to mitigate this threat is to
> ignore very small hop limits. The nodes could implement a
> configurable minimum hop limit, and ignore attempts to set it below
> said limit.
Signed-off-by: D.S. Ljungmark <ljungmark@modio.se>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0c294c53a ]
On s390x, gcc 4.8 compiles this part of tcp_v6_early_demux()
struct dst_entry *dst = sk->sk_rx_dst;
if (dst)
dst = dst_check(dst, inet6_sk(sk)->rx_dst_cookie);
to code reading sk->sk_rx_dst twice, once for the test and once for
the argument of ip6_dst_check() (dst_check() is inline). This allows
ip6_dst_check() to be called with null first argument, causing a crash.
Protect sk->sk_rx_dst access by ACCESS_ONCE() both in IPv4 and IPv6
TCP early demux code.
Fixes: 41063e9dd1 ("ipv4: Early TCP socket demux.")
Fixes: c7109986db ("ipv6: Early TCP socket demux")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b8d9117cc upstream.
The timeout entries are sizeof(int) rather than sizeof(long), which
means that when they were getting read we'd also leak kernel memory
to userspace along with the timeout values.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db27ebb111 upstream.
Max unacked packets/bytes is an int while sizeof(long) was used in the
sysctl table.
This means that when they were getting read we'd also leak kernel memory
to userspace along with the timeout values.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 355a901e6c ("tcp: make connect() mem charging friendly")
changed tcp_send_syn_data() to perform an open-coded copy of the 'syn'
skb rather than using skb_copy_expand().
The open-coded copy does not cover the skb_shared_info::gso_segs
field, so in the new skb it is left set to 0. When this commit was
backported into stable branches between 3.10.y and 3.16.7-ckty
inclusive, it triggered the BUG() in tcp_transmit_skb().
Since Linux 3.18 the GSO segment count is kept in the
tcp_skb_cb::tcp_gso_segs field and tcp_send_syn_data() does copy the
tcp_skb_cb structure to the new skb, so mainline and newer stable
branches are not affected.
Set skb_shared_info::gso_segs to the correct value of 1.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0c22119f5 upstream.
The mesh forwarding path was not checking that data
frames were protected when running an encrypted network;
add the necessary check.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa75ebc275 upstream.
Some APs experience problems when working with
U-APSD. Decreasing the probability of that
happening by using legacy mode for all ACs but VO
isn't enough.
Cisco 4410N originally forced us to enable VO by
default only because it treated non-VO ACs as
legacy.
However some APs (notably Netgear R7000) silently
reclassify packets to different ACs. Since u-APSD
ACs require trigger frames for frame retrieval
clients would never see some frames (e.g. ARP
responses) or would fetch them accidentally after
a long time.
It makes little sense to enable u-APSD queues by
default because it needs userspace applications to
be aware of it to actually take advantage of the
possible additional powersavings. Implicitly
depending on driver autotrigger frame support
doesn't make much sense.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 496fcc294d upstream.
As HT/VHT depend heavily on QoS/WMM, it's not a good idea to
let userspace add clients that have HT/VHT but not QoS/WMM.
Since it does so in certain cases we've observed (client is
using HT IEs but not QoS/WMM) just ignore the HT/VHT info at
this point and don't pass it down to the drivers which might
unconditionally use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78296c97ca upstream.
As soon as extract_icmp6_fields() returns, its local storage (automatic
variables) is deallocated and can be overwritten.
Lets add an additional parameter to make sure storage is valid long
enough.
While we are at it, adds some const qualifiers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: b64c9256a9 ("tproxy: added IPv6 support to the socket match")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 579eb62ac3 upstream.
commit f5a41847ac ("ipvs: move ip_route_me_harder for ICMP")
from 2.6.37 introduced ip_route_me_harder() call for responses to
local clients, so that we can provide valid rt_src after SNAT.
It was used by TCP to provide valid daddr for ip_send_reply().
After commit 0a5ebb8000 ("ipv4: Pass explicit daddr arg to
ip_send_reply()." from 3.0 this rerouting is not needed anymore
and should be avoided, especially in LOCAL_IN.
Fixes 3.12.33 crash in xfrm reported by Florian Wiessner:
"3.12.33 - BUG xfrm_selector_match+0x25/0x2f6"
Reported-by: Smart Weblications GmbH - Florian Wiessner <f.wiessner@smart-weblications.de>
Tested-by: Smart Weblications GmbH - Florian Wiessner <f.wiessner@smart-weblications.de>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 528c943f3b upstream.
ip_vs_conn_fill_param_sync() gets in param.pe a module
reference for persistence engine from __ip_vs_pe_getbyname()
but forgets to put it. Problem occurs in backup for
sync protocol v1 (2.6.39).
Also, pe_data usually comes in sync messages for
connection templates and ip_vs_conn_new() copies
the pointer only in this case. Make sure pe_data
is not leaked if it comes unexpectedly for normal
connections. Leak can happen only if bogus messages
are sent to backup server.
Fixes: fe5e7a1efb ("IPVS: Backup, Adding Version 1 receive capability")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 969439016d upstream.
When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.
Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: Austin Schuh <austin@peloton-tech.com>
Reported-by: Daniel Steer <daniel.steer@mclaren.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 355a901e6c ]
While working on sk_forward_alloc problems reported by Denys
Fedoryshchenko, we found that tcp connect() (and fastopen) do not call
sk_wmem_schedule() for SYN packet (and/or SYN/DATA packet), so
sk_forward_alloc is negative while connect is in progress.
We can fix this by calling regular sk_stream_alloc_skb() both for the
SYN packet (in tcp_connect()) and the syn_data packet in
tcp_send_syn_data()
Then, tcp_send_syn_data() can avoid copying syn_data as we simply
can manipulate syn_data->cb[] to remove SYN flag (and increment seq)
Instead of open coding memcpy_fromiovecend(), simply use this helper.
This leaves in socket write queue clean fast clone skbs.
This was tested against our fastopen packetdrill tests.
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91edd096e2 ]
Commit db31c55a6f (net: clamp ->msg_namelen instead of returning an
error) introduced the clamping of msg_namelen when the unsigned value
was larger than sizeof(struct sockaddr_storage). This caused a
msg_namelen of -1 to be valid. The native code was subsequently fixed by
commit dbb490b965 (net: socket: error on a negative msg_namelen).
In addition, the native code sets msg_namelen to 0 when msg_name is
NULL. This was done in commit (6a2a2b3ae0 net:socket: set msg_namelen
to 0 if msg_name is passed as NULL in msghdr struct from userland) and
subsequently updated by 08adb7dabd (fold verify_iovec() into
copy_msghdr_from_user()).
This patch brings the get_compat_msghdr() in line with
copy_msghdr_from_user().
Fixes: db31c55a6f (net: clamp ->msg_namelen instead of returning an error)
Cc: David S. Miller <davem@davemloft.net>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d22e153718 ]
tcp_send_fin() does not account for the memory it allocates properly, so
sk_forward_alloc can be negative in cases where we've sent a FIN:
ss example output (ss -amn | grep -B1 f4294):
tcp FIN-WAIT-1 0 1 192.168.0.1:45520 192.0.2.1:8080
skmem:(r0,rb87380,t0,tb87380,f4294966016,w1280,o0,bl0)
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73ba57bfae ]
for throw routes to trigger evaluation of other policy rules
EAGAIN needs to be propagated up to fib_rules_lookup
similar to how its done for IPv4
A simple testcase for verification is:
ip -6 rule add lookup 33333 priority 33333
ip -6 route add throw 2001:db8::1
ip -6 route add 2001:db8::1 via fe80::1 dev wlan0 table 33333
ip route get 2001:db8::1
Signed-off-by: Steven Barth <cyrus@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7d985ed1dc ]
[I would really like an ACK on that one from dhowells; it appears to be
quite straightforward, but...]
MSG_PEEK isn't passed to ->recvmsg() via msg->msg_flags; as the matter of
fact, neither the kernel users of rxrpc, nor the syscalls ever set that bit
in there. It gets passed via flags; in fact, another such check in the same
function is done correctly - as flags & MSG_PEEK.
It had been that way (effectively disabled) for 8 years, though, so the patch
needs beating up - that case had never been tested. If it is correct, it's
-stable fodder.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3eeff778e0 ]
It should be checking flags, not msg->msg_flags. It's ->sendmsg()
instances that need to look for that in ->msg_flags, ->recvmsg() ones
(including the other ->recvmsg() instance in that file, as well as
unix_dgram_recvmsg() this one claims to be imitating) check in flags.
Braino had been introduced in commit dcda13 ("caif: Bugfix - use MSG_TRUNC
in receive") back in 2010, so it goes quite a while back.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c8e2c80d7e ]
inet_diag_dump_one_icsk() allocates too small skb.
Add inet_sk_attr_size() helper right before inet_sk_diag_fill()
so that it can be updated if/when new attributes are added.
iproute2/ss currently does not use this dump_one() interface,
this might explain nobody noticed this problem yet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f862e07cf9 ]
The rds_iw_update_cm_id function stores a large 'struct rds_sock' object
on the stack in order to pass a pair of addresses. This happens to just
fit withint the 1024 byte stack size warning limit on x86, but just
exceed that limit on ARM, which gives us this warning:
net/rds/iw_rdma.c:200:1: warning: the frame size of 1056 bytes is larger than 1024 bytes [-Wframe-larger-than=]
As the use of this large variable is basically bogus, we can rearrange
the code to not do that. Instead of passing an rds socket into
rds_iw_get_device, we now just pass the two addresses that we have
available in rds_iw_update_cm_id, and we change rds_iw_get_mr accordingly,
to create two address structures on the stack there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1711fd9add upstream.
POLL_OUT isn't what callers of ->poll() are expecting to see; it's
actually __SI_POLL | 2 and it's a siginfo code, not a poll bitmap
bit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Bruce Fields <bfields@fieldses.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c3fbe3cf2 upstream.
In case an infinite timeout (0) is requested, the irda wait_until_sent
implementation would use a zero poll timeout rather than the default
200ms.
Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c1c98a3bb upstream.
The current minstrel_ht rate control behavior is somewhat optimistic in
trying to find optimum TX rate. While this is usually fine for normal
Data frames, there are cases where a more conservative set of retry
parameters would be beneficial to make the connection more robust.
EAPOL frames are critical to the authentication and especially the
EAPOL-Key message 4/4 (the last message in the 4-way handshake) is
important to get through to the AP. If that message is lost, the only
recovery mechanism in many cases is to reassociate with the AP and start
from scratch. This can often be avoided by trying to send the frame with
more conservative rate and/or with more link layer retries.
In most cases, minstrel_ht is currently using the initial EAPOL-Key
frames for probing higher rates and this results in only five link layer
transmission attempts (one at high(ish) MCS and four at MCS0). While
this works with most APs, it looks like there are some deployed APs that
may have issues with the EAPOL frames using HT MCS immediately after
association. Similarly, there may be issues in cases where the signal
strength or radio environment is not good enough to be able to get
frames through even at couple of MCS 0 tries.
The best approach for this would likely to be to reduce the TX rate for
the last rate (3rd rate parameter in the set) to a low basic rate (say,
6 Mbps on 5 GHz and 2 or 5.5 Mbps on 2.4 GHz), but doing that cleanly
requires some more effort. For now, we can start with a simple one-liner
that forces the minimum rate to be used for EAPOL frames similarly how
the TX rate is selected for the IEEE 802.11 Management frames. This does
result in a small extra latency added to the cases where the AP would be
able to receive the higher rate, but taken into account how small number
of EAPOL frames are used, this is likely to be insignificant. A future
optimization in the minstrel_ht design can also allow this patch to be
reverted to get back to the more optimized initial TX rate.
It should also be noted that many drivers that do not use minstrel as
the rate control algorithm are already doing similar workarounds by
forcing the lowest TX rate to be used for EAPOL frames.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9145736d48 ]
1. For an IPv4 ping socket, ping_check_bind_addr does not check
the family of the socket address that's passed in. Instead,
make it behave like inet_bind, which enforces either that the
address family is AF_INET, or that the family is AF_UNSPEC and
the address is 0.0.0.0.
2. For an IPv6 ping socket, ping_check_bind_addr returns EINVAL
if the socket family is not AF_INET6. Return EAFNOSUPPORT
instead, for consistency with inet6_bind.
3. Make ping_v4_sendmsg and ping_v6_sendmsg return EAFNOSUPPORT
instead of EINVAL if an incorrect socket address structure is
passed in.
4. Make IPv6 ping sockets be IPv6-only. The code does not support
IPv4, and it cannot easily be made to support IPv4 because
the protocol numbers for ICMP and ICMPv6 are different. This
makes connect(::ffff:192.0.2.1) fail with EAFNOSUPPORT instead
of making the socket unusable.
Among other things, this fixes an oops that can be triggered by:
int s = socket(AF_INET, SOCK_DGRAM, IPPROTO_ICMP);
struct sockaddr_in6 sin6 = {
.sin6_family = AF_INET6,
.sin6_addr = in6addr_any,
};
bind(s, (struct sockaddr *) &sin6, sizeof(sin6));
Change-Id: If06ca86d9f1e4593c0d6df174caca3487c57a241
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit acf8dd0a9d ]
If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a
UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to
CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer
checksum is to be computed on segmentation. However, in this case,
skb->csum_start and skb->csum_offset are never set as raw socket
transmit path bypasses udp_send_skb() where they are usually set. As a
result, driver may access invalid memory when trying to calculate the
checksum and store the result (as observed in virtio_net driver).
Moreover, the very idea of modifying the userspace provided UDP header
is IMHO against raw socket semantics (I wasn't able to find a document
clearly stating this or the opposite, though). And while allowing
CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit
too intrusive change just to handle a corner case like this. Therefore
disallowing UFO for packets from SOCK_DGRAM seems to be the best option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d720d8cec5 ]
With commit a7526eb5d0 (net: Unbreak compat_sys_{send,recv}msg), the
MSG_CMSG_COMPAT flag is blocked at the compat syscall entry points,
changing the kernel compat behaviour from the one before the commit it
was trying to fix (1be374a051, net: Block MSG_CMSG_COMPAT in
send(m)msg and recv(m)msg).
On 32-bit kernels (!CONFIG_COMPAT), MSG_CMSG_COMPAT is 0 and the native
32-bit sys_sendmsg() allows flag 0x80000000 to be set (it is ignored by
the kernel). However, on a 64-bit kernel, the compat ABI is different
with commit a7526eb5d0.
This patch changes the compat_sys_{send,recv}msg behaviour to the one
prior to commit 1be374a051.
The problem was found running 32-bit LTP (sendmsg01) binary on an arm64
kernel. Arguably, LTP should not pass 0xffffffff as flags to sendmsg()
but the general rule is not to break user ABI (even when the user
behaviour is not entirely sane).
Fixes: a7526eb5d0 (net: Unbreak compat_sys_{send,recv}msg)
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a4176a9391 ]
colons are used as a separator in netdev device lookup in dev_ioctl.c
Specific functions are SIOCGIFTXQLEN SIOCETHTOOL SIOCSIFNAME
Signed-off-by: Matthew Thode <mthode@mthode.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 34eea79e26 ]
In tcf_em_validate(), after calling request_module() to load the
kind-specific module, set em->ops to NULL before returning -EAGAIN, so
that module_put() is not called again by tcf_em_tree_destroy().
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e32e733d1 ]
ip_check_defrag() may be used by af_packet to defragment outgoing packets.
skb_network_offset() of af_packet's outgoing packets is not zero.
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fba04a9e0c ]
skb_copy_bits() returns zero on success and negative value on error,
so it is needed to invert the condition in ip_check_defrag().
Fixes: 1bf3751ec9 ("ipv4: ip_check_defrag must not modify skb before unsharing")
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c4cff0cf5 ]
The gnet_stats_copy_app() function gets called, more often than not, with its
second argument a pointer to an automatic variable in the caller's stack.
Therefore, to avoid copying garbage afterwards when calling
gnet_stats_finish_copy(), this data is better copied to a dynamically allocated
memory that gets freed after use.
[xiyou.wangcong@gmail.com: remove a useless kfree()]
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7afb8886a0 ]
Ignacy reported that when eth0 is down and add a vlan device
on top of it like:
ip link add link eth0 name eth0.1 up type vlan id 1
We will get a refcount leak:
unregister_netdevice: waiting for eth0.1 to become free. Usage count = 2
The problem is when rtnl_configure_link() fails in rtnl_newlink(),
we simply call unregister_device(), but for stacked device like vlan,
we almost do nothing when we unregister the upper device, more work
is done when we unregister the lower device, so call its ->dellink().
Reported-by: Ignacy Gawedzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b4711757d ]
ipv6_cow_metrics() currently assumes only DST_HOST routes require
dynamic metrics allocation from inetpeer. The assumption breaks
when ndisc discovered router with RTAX_MTU and RTAX_HOPLIMIT metric.
Refer to ndisc_router_discovery() in ndisc.c and note that dst_metric_set()
is called after the route is created.
This patch creates the metrics array (by calling dst_cow_metrics_generic) in
ipv6_cow_metrics().
Test:
radvd.conf:
interface qemubr0
{
AdvLinkMTU 1300;
AdvCurHopLimit 30;
prefix fd00:face:face:face::/64
{
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr off;
};
};
Before:
[root@qemu1 ~]# ip -6 r show | egrep -v unreachable
fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec
fe80::/64 dev eth0 proto kernel metric 256
default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec
After:
[root@qemu1 ~]# ip -6 r show | egrep -v unreachable
fd00:face:face:face::/64 dev eth0 proto kernel metric 256 expires 27sec mtu 1300
fe80::/64 dev eth0 proto kernel metric 256 mtu 1300
default via fe80::74df:d0ff:fe23:8ef2 dev eth0 proto ra metric 1024 expires 27sec mtu 1300 hoplimit 30
Fixes: 8e2ec63917 (ipv6: don't use inetpeer to store metrics for routes.)
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 364d5716a7 ]
ifla_vf_policy[] is wrong in advertising its individual member types as
NLA_BINARY since .type = NLA_BINARY in combination with .len declares the
len member as *max* attribute length [0, len].
The issue is that when do_setvfinfo() is being called to set up a VF
through ndo handler, we could set corrupted data if the attribute length
is less than the size of the related structure itself.
The intent is exactly the opposite, namely to make sure to pass at least
data of minimum size of len.
Fixes: ebc08a6f47 ("rtnetlink: Add VF config code to rtnetlink")
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7744b5f369 ]
This patch fixes two issues in UDP checksum computation in pktgen.
First, the pseudo-header uses the source and destination IP
addresses. Currently, the ports are used for IPv4.
Second, the UDP checksum covers both header and data. So we need to
generate the data earlier (move pktgen_finalize_skb up), and compute
the checksum for UDP header + data.
Fixes: c26bf4a513 ("pktgen: Add UDPCSUM flag to support UDP checksums")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7eb71e0351 upstream.
It turns out it's possible to get __remove_osd() called twice on the
same OSD. That doesn't sit well with rb_erase() - depending on the
shape of the tree we can get a NULL dereference, a soft lockup or
a random crash at some point in the future as we end up touching freed
memory. One scenario that I was able to reproduce is as follows:
<osd3 is idle, on the osd lru list>
<con reset - osd3>
con_fault_finish()
osd_reset()
<osdmap - osd3 down>
ceph_osdc_handle_map()
<takes map_sem>
kick_requests()
<takes request_mutex>
reset_changed_osds()
__reset_osd()
__remove_osd()
<releases request_mutex>
<releases map_sem>
<takes map_sem>
<takes request_mutex>
__kick_osd_requests()
__reset_osd()
__remove_osd() <-- !!!
A case can be made that osd refcounting is imperfect and reworking it
would be a proper resolution, but for now Sage and I decided to fix
this by adding a safe guard around __remove_osd().
Fixes: http://tracker.ceph.com/issues/8087
Cc: Sage Weil <sage@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc9f1f518c upstream.
No reason to use BUG_ON for osd request list assertions.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c6e6fc53e upstream.
It is important that both regular and lingering requests lists are
empty when the OSD is removed.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cfbf654efc ]
When making use of RFC5061, section 4.2.4. for setting the primary IP
address, we're passing a wrong parameter header to param_type2af(),
resulting always in NULL being returned.
At this point, param.p points to a sctp_addip_param struct, containing
a sctp_paramhdr (type = 0xc004, length = var), and crr_id as a correlation
id. Followed by that, as also presented in RFC5061 section 4.2.4., comes
the actual sctp_addr_param, which also contains a sctp_paramhdr, but
this time with the correct type SCTP_PARAM_IPV{4,6}_ADDRESS that
param_type2af() can make use of. Since we already hold a pointer to
addr_param from previous line, just reuse it for param_type2af().
Fixes: d6de309759 ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Saran Maruti Ramanara <saran.neti@telus.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bdbbb8527b ]
In commit be9f4a44e7 ("ipv4: tcp: remove per net tcp_sock")
I tried to address contention on a socket lock, but the solution
I chose was horrible :
commit 3a7c384ffd ("ipv4: tcp: unicast_sock should not land outside
of TCP stack") addressed a selinux regression.
commit 0980e56e50 ("ipv4: tcp: set unicast_sock uc_ttl to -1")
took care of another regression.
commit b5ec8eeac4 ("ipv4: fix ip_send_skb()") fixed another regression.
commit 811230cd85 ("tcp: ipv4: initialize unicast_sock sk_pacing_rate")
was another shot in the dark.
Really, just use a proper socket per cpu, and remove the skb_orphan()
call, to re-enable flow control.
This solves a serious problem with FQ packet scheduler when used in
hostile environments, as we do not want to allocate a flow structure
for every RST packet sent in response to a spoofed packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 811230cd85 ]
When I added sk_pacing_rate field, I forgot to initialize its value
in the per cpu unicast_sock used in ip_send_unicast_reply()
This means that for sch_fq users, RST packets, or ACK packets sent
on behalf of TIME_WAIT sockets might be sent to slowly or even dropped
once we reach the per flow limit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 95bd09eb27 ("tcp: TSO packets automatic sizing")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59ccaaaa49 ]
Reported in: https://bugzilla.kernel.org/show_bug.cgi?id=92081
This patch avoids calling rtnl_notify if the device ndo_bridge_getlink
handler does not return any bytes in the skb.
Alternately, the skb->len check can be moved inside rtnl_notify.
For the bridge vlan case described in 92081, there is also a fix needed
in bridge driver to generate a proper notification. Will fix that in
subsequent patch.
v2: rebase patch on net tree
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 06539d3071 ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e9e16e614 ]
Lubomir Rintel reported that during replacing a route the interface
reference counter isn't correctly decremented.
To quote bug <https://bugzilla.kernel.org/show_bug.cgi?id=91941>:
| [root@rhel7-5 lkundrak]# sh -x lal
| + ip link add dev0 type dummy
| + ip link set dev0 up
| + ip link add dev1 type dummy
| + ip link set dev1 up
| + ip addr add 2001:db8:8086::2/64 dev dev0
| + ip route add 2001:db8:8086::/48 dev dev0 proto static metric 20
| + ip route add 2001:db8:8088::/48 dev dev1 proto static metric 10
| + ip route replace 2001:db8:8086::/48 dev dev1 proto static metric 20
| + ip link del dev0 type dummy
| Message from syslogd@rhel7-5 at Jan 23 10:54:41 ...
| kernel:unregister_netdevice: waiting for dev0 to become free. Usage count = 2
|
| Message from syslogd@rhel7-5 at Jan 23 10:54:51 ...
| kernel:unregister_netdevice: waiting for dev0 to become free. Usage count = 2
During replacement of a rt6_info we must walk all parent nodes and check
if the to be replaced rt6_info got propagated. If so, replace it with
an alive one.
Fixes: 4a287eba2d ("IPv6 routing, NLM_F_* flag support: REPLACE and EXCL flags support, warn about missing CREATE flag")
Reported-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
