commit 8ef42ddd9a upstream.
Not all host controller drivers have bus-suspend and bus-resume
methods. When one doesn't, it will cause problems if runtime PM is
enabled in the kernel. The PM core will attempt to suspend the
controller's root hub, the suspend will fail because there is no
bus-suspend routine, and a -EBUSY error code will be returned to the
PM core. This will cause the suspend attempt to be repeated shortly
thereafter, in a never-ending loop.
Part of the problem is that the original error code -ENOENT gets
changed to -EBUSY in usb_runtime_suspend(), on the grounds that the PM
core will interpret -ENOENT as meaning that the root hub has gotten
into a runtime-PM error state. While this change is appropriate for
real USB devices, it's not such a good idea for a root hub. In fact,
considering the root hub to be in a runtime-PM error state would not
be far from the truth. Therefore this patch updates
usb_runtime_suspend() so that it adjusts error codes only for
non-root-hub devices.
Furthermore, the patch attempts to prevent the problem from occurring
in the first place by not enabling runtime PM by default for root hubs
whose host controller driver doesn't have bus_suspend and bus_resume
methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b38f09ccc3 upstream.
Sony VAIO t-series machines are not capable of switching usb2 ports over
from Intel EHCI to xHCI controller. If tried the USB2 port will be left
unconnected and unusable.
This patch should be backported to stable kernels as old as 3.12,
that contain the commit 26b76798e0
"Intel xhci: refactor EHCI/xHCI port switching"
Reported-by: Jorge <xxopxe@gmail.com>
Tested-by: Jorge <xxopxe@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c03890ff5e upstream.
A recent patch that purported to fix firmware download on big-endian
machines failed to add the corresponding sparse annotation to the
i2c-header. This was reported by the kbuild test robot.
Adding the appropriate annotation revealed another endianess bug related
to the i2c-header Size-field in a code path that is exercised when the
firmware is actually being downloaded (and not just verified and left
untouched unless older than the firmware at hand).
This patch adds the required sparse annotation to the i2c-header and
makes sure that the Size-field is sent in little-endian byte order
during firmware download also on big-endian machines.
Note that this patch is only compile-tested, but that there is no
functional change for little-endian systems.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Ludovic Drolez <ldrolez@debian.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0839d757e upstream.
The NovaTech OrionLXm uses an onboard FTDI serial converter for JTAG and
console access.
Here is the lsusb output:
Bus 004 Device 123: ID 0403:7c90 Future Technology Devices
International, Ltd
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5dc2808c47 upstream.
Lists of endpoints are stored for bandwidth calculation for roothub ports.
Make sure we remove all endpoints from the list before the whole device,
containing its endpoints list_head stuctures, is freed.
This used to be done in the wrong order in xhci_mem_cleanup(),
and triggered an oops in resume from S4 (hibernate).
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df602c2d23 upstream.
Even if the USB-to-ATAPI converter supported multiple LUNs, this
driver would always detect the same physical device or media because
it doesn't use srb->device->lun in any way.
Tested with an Hewlett-Packard CD-Writer Plus 8200e.
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d7c0136a5 upstream.
Dan writes:
"The Dell drivers use the same configuration for PIDs:
81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card
These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.
>From DellGobi5kSetup.exe from the Dell drivers:
usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1db30a2a7 upstream.
Some OHCI controllers from ATI/AMD seem to have difficulty with
"global" USB suspend, that is, suspending an entire USB bus without
setting the suspend feature for each port connected to a device. When
we try to resume the child devices, the controller gives timeout
errors on the unsuspended ports, requiring resets, and can even cause
ohci-hcd to hang; see
http://marc.info/?l=linux-usb&m=139514332820398&w=2
and the following messages.
This patch fixes the problem by adding a new quirk flag to ohci-hcd.
The flag causes the ohci_rh_suspend() routine to suspend each
unsuspended, enabled port before suspending the root hub. This
effectively converts the "global" suspend to an ordinary root-hub
suspend. There is no need to unsuspend these ports when the root hub
is resumed, because the child devices will be resumed anyway in the
course of a normal system resume ("global" suspend is never used for
runtime PM).
This patch should be applied to all stable kernels which include
commit 0aa2832dd0 (USB: use "global suspend" for system sleep on
USB-2 buses) or a backported version thereof.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Peter Münster <pmlists@free.fr>
Tested-by: Peter Münster <pmlists@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 886c7c426d upstream.
When using dt resources retrieval (interrupts and reg properties) there is
no predefined order for these resources in the platform dev resource
table. Also don't expect the number of resource to be always 2.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d183c81929 upstream.
Per reference manuals of Freescale P1020 and P2020 SoCs, USB controller
present in these SoCs has bit 17 of USBx_CONTROL register marked as
Reserved - there is no PHY_CLK_VALID bit there.
Testing for this bit in ehci_fsl_setup_phy() behaves differently on two
P1020RDB boards available here - on one board test passes and fsl-usb
init succeeds, but on other board test fails, causing fsl-usb init to
fail.
This patch changes ehci_fsl_setup_phy() not to test PHY_CLK_VALID on
controller version 1.6 that (per manual) does not have this bit.
Signed-off-by: Nikita Yushchenko <nyushchenko@dev.rtsoft.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34f972d615 upstream.
A number of older CMOTech modems are based on Qualcomm
chips. The blacklisted interfaces are QMI/wwan.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5509076d1b upstream.
During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.
Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.
Reported-by: Ludovic Drolez <ldrolez@debian.org>
Tested-by: Ludovic Drolez <ldrolez@debian.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10164c2ad6 upstream.
Fix driver new_id sysfs-attribute removal deadlock by making sure to
not hold any locks that the attribute operations grab when removing the
attribute.
Specifically, usb_serial_deregister holds the table mutex when
deregistering the driver, which includes removing the new_id attribute.
This can lead to a deadlock as writing to new_id increments the
attribute's active count before trying to grab the same mutex in
usb_serial_probe.
The deadlock can easily be triggered by inserting a sleep in
usb_serial_deregister and writing the id of an unbound device to new_id
during module unload.
As the table mutex (in this case) is used to prevent subdriver unload
during probe, it should be sufficient to only hold the lock while
manipulating the usb-serial driver list during deregister. A racing
probe will then either fail to find a matching subdriver or fail to get
the corresponding module reference.
Since v3.15-rc1 this also triggers the following lockdep warning:
======================================================
[ INFO: possible circular locking dependency detected ]
3.15.0-rc2 #123 Tainted: G W
-------------------------------------------------------
modprobe/190 is trying to acquire lock:
(s_active#4){++++.+}, at: [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
but task is already holding lock:
(table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (table_lock){+.+.+.}:
[<c0075f84>] __lock_acquire+0x1694/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c03af3cc>] _raw_spin_lock+0x4c/0x5c
[<c02bbc24>] usb_store_new_id+0x14c/0x1ac
[<bf007eb4>] new_id_store+0x68/0x70 [usbserial]
[<c025f568>] drv_attr_store+0x30/0x3c
[<c01690e0>] sysfs_kf_write+0x5c/0x60
[<c01682c0>] kernfs_fop_write+0xd4/0x194
[<c010881c>] vfs_write+0xbc/0x198
[<c0108e4c>] SyS_write+0x4c/0xa0
[<c000f880>] ret_fast_syscall+0x0/0x48
-> #0 (s_active#4){++++.+}:
[<c03a7a28>] print_circular_bug+0x68/0x2f8
[<c0076218>] __lock_acquire+0x1928/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c0166b70>] __kernfs_remove+0x254/0x310
[<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
[<c0169fb8>] remove_files.isra.1+0x48/0x84
[<c016a2fc>] sysfs_remove_group+0x58/0xac
[<c016a414>] sysfs_remove_groups+0x34/0x44
[<c02623b8>] driver_remove_groups+0x1c/0x20
[<c0260e9c>] bus_remove_driver+0x3c/0xe4
[<c026235c>] driver_unregister+0x38/0x58
[<bf007fb4>] usb_serial_bus_deregister+0x84/0x88 [usbserial]
[<bf004db4>] usb_serial_deregister+0x6c/0x78 [usbserial]
[<bf005330>] usb_serial_deregister_drivers+0x2c/0x4c [usbserial]
[<bf016618>] usb_serial_module_exit+0x14/0x1c [sierra]
[<c009d6cc>] SyS_delete_module+0x184/0x210
[<c000f880>] ret_fast_syscall+0x0/0x48
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(table_lock);
lock(s_active#4);
lock(table_lock);
lock(s_active#4);
*** DEADLOCK ***
1 lock held by modprobe/190:
#0: (table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
stack backtrace:
CPU: 0 PID: 190 Comm: modprobe Tainted: G W 3.15.0-rc2 #123
[<c0015e10>] (unwind_backtrace) from [<c0013728>] (show_stack+0x20/0x24)
[<c0013728>] (show_stack) from [<c03a9a54>] (dump_stack+0x24/0x28)
[<c03a9a54>] (dump_stack) from [<c03a7cac>] (print_circular_bug+0x2ec/0x2f8)
[<c03a7cac>] (print_circular_bug) from [<c0076218>] (__lock_acquire+0x1928/0x1ce4)
[<c0076218>] (__lock_acquire) from [<c0076de8>] (lock_acquire+0xb4/0x154)
[<c0076de8>] (lock_acquire) from [<c0166b70>] (__kernfs_remove+0x254/0x310)
[<c0166b70>] (__kernfs_remove) from [<c0167aa0>] (kernfs_remove_by_name_ns+0x4c/0x94)
[<c0167aa0>] (kernfs_remove_by_name_ns) from [<c0169fb8>] (remove_files.isra.1+0x48/0x84)
[<c0169fb8>] (remove_files.isra.1) from [<c016a2fc>] (sysfs_remove_group+0x58/0xac)
[<c016a2fc>] (sysfs_remove_group) from [<c016a414>] (sysfs_remove_groups+0x34/0x44)
[<c016a414>] (sysfs_remove_groups) from [<c02623b8>] (driver_remove_groups+0x1c/0x20)
[<c02623b8>] (driver_remove_groups) from [<c0260e9c>] (bus_remove_driver+0x3c/0xe4)
[<c0260e9c>] (bus_remove_driver) from [<c026235c>] (driver_unregister+0x38/0x58)
[<c026235c>] (driver_unregister) from [<bf007fb4>] (usb_serial_bus_deregister+0x84/0x88 [usbserial])
[<bf007fb4>] (usb_serial_bus_deregister [usbserial]) from [<bf004db4>] (usb_serial_deregister+0x6c/0x78 [usbserial])
[<bf004db4>] (usb_serial_deregister [usbserial]) from [<bf005330>] (usb_serial_deregister_drivers+0x2c/0x4c [usbserial])
[<bf005330>] (usb_serial_deregister_drivers [usbserial]) from [<bf016618>] (usb_serial_module_exit+0x14/0x1c [sierra])
[<bf016618>] (usb_serial_module_exit [sierra]) from [<c009d6cc>] (SyS_delete_module+0x184/0x210)
[<c009d6cc>] (SyS_delete_module) from [<c000f880>] (ret_fast_syscall+0x0/0x48)
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e01280d28 upstream.
This reverts commit 1ebca9dad5.
This device was erroneously added to the sierra driver even though it's
not a Sierra device and was already handled by the option driver.
Cc: Richard Farina <sidhayn@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd73bd8831 upstream.
Fix regression introduced by commit 8e493ca176 ("USB: usb_wwan: fix
bulk-urb allocation") by making sure to require both bulk-in and out
endpoints during port probe.
The original option driver (which usb_wwan is based on) was written
under the assumption that either endpoint could be missing, but
evidently this cannot have been tested properly. Specifically, it would
handle opening a device without bulk-in (but would blow up during resume
which was implemented later), but not a missing bulk-out in write()
(although it is handled in some places such as write_room()).
Fortunately (?), the driver also got the test for missing endpoints
wrong so the urbs were in fact always allocated, although they would be
initialised using the wrong endpoint address (0) and any submission of
such an urb would fail.
The commit mentioned above fixed the test for missing endpoints but
thereby exposed the other bugs which would now generate null-pointer
exceptions rather than failed urb submissions.
The regression was introduced in v3.7, but the offending commit was also
marked for stable.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 895d240d1d upstream.
By specifying NO_UNION_NORMAL the ACM driver does only use the first two
USB interfaces (modem data & control). The AT Port, Diagnostic and NMEA
interfaces are left to the USB serial driver.
Signed-off-by: Michael Ulbricht <michael.ulbricht@systec-electronic.com>
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f2fe2d274 upstream.
To avoid memory fetch underflows with larger USB transfers, Tegra SoCs
need txfill_tuning's txfifothresh register field set to a non-default
value. Add a custom reset override in order to set this up.
These values are recommended practice for all Tegra chips. However,
I've only noticed practical problems when not setting them this way on
systems using Tegra124. Hence, CC: stable only for recent kernels which
actually support Tegra124.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f81b6d22a upstream.
We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.
The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.
This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.
This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae63674714 "USB: xhci: URB
cancellation support."
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aec044cc2 upstream.
When a driver doesn't have pre_reset, post_reset, or reset_resume
methods, the USB core unbinds that driver when its device undergoes a
reset or a reset-resume, and then rebinds it afterward.
The existing straightforward implementation can lead to problems,
because each interface gets unbound and rebound before the next
interface is handled. If a driver claims additional interfaces, the
claim may fail because the old binding instance may still own the
additional interface when the new instance tries to claim it.
This patch fixes the problem by first unbinding all the interfaces
that are marked (i.e., their needs_binding flag is set) and then
rebinding all of them.
The patch also makes the helper functions in driver.c a little more
uniform and adjusts some out-of-date comments.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: "Poulain, Loic" <loic.poulain@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a31a942a14 upstream.
Tests have shown that when a power-up transition is followed by other
PHY operations too quickly, the USB port appears dead. Waiting 1ms fixes
this problem.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ead5178bf4 upstream.
Add new ulpi IDs which are available on Xilinx Zynq boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3063a12be2 upstream.
commi 30a70b0 (usb: musb: fix obex in g_nokia.ko
causing kernel panic) removed phy_power_on()
and phy_power_off() calls from runtime PM callbacks
but it failed to note that the driver depended
on pm_runtime_get_sync() calls to power up the PHY,
thus leaving some platforms without any means to
have a working PHY.
Fix that by enabling the phy during omap2430_musb_init()
and killing it in omap2430_musb_exit().
Fixes: 30a70b0 (usb: musb: fix obex in g_nokia.ko causing kernel panic)
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reported-by: Michael Scott <hashcode0f@gmail.com>
Tested-by: Michael Scott <hashcode0f@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Reported-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eee3f15d5f upstream.
instead of relying on the otg pointer, which
can be NULL in certain cases, we can use the
gadget and host pointers we already hold inside
struct musb.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 610183051d upstream.
commit 388e5c5 (usb: dwc3: remove dwc3 dependency
on host AND gadget.) created the possibility for
host-only and peripheral-only dwc3 builds but
left a possible randconfig build error when host-only
builds are selected.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06f9b6e596 upstream.
Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.
Because of that, what used to be 8 bits long, has become 9 bits long.
Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.
So in dwc3_event_devt, the bit mask should be:
event_info [24:16] 9 bits
reserved31_25 [31:25] 7 bits
This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.
[ balbi@ti.com : improve commit log a bit ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01bb59ebff upstream.
When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
warning:
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]
Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.
This warning has been in since 3.2 kernel and was
caused by commit 421aa841a1
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c09ec25d36 upstream.
The same issue like with Panther Point chipsets. If the USB ports are
switched to xHCI on shutdown, the xHCI host will send a spurious interrupt,
which will wake the system. Some BIOS have work around for this, but not all.
One example is Compulab's mini-desktop, the Intense-PC2.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.
This patch should be backported to stable kernels as old as 3.12,
that contain the commit 638298dc66
"xhci: Fix spurious wakeups after S5 on Haswell"
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcffae7708 upstream.
xHCI driver has its own pci probe function that will call usb_hcd_pci_probe
to register its usb-2 bus, and then continue to manually register the
usb-3 bus. usb_hcd_pci_probe does a pm_runtime_put_noidle at the end and
might thus trigger a runtime suspend before the usb-3 bus is ready.
Prevent the runtime suspend by increasing the usage count in the
beginning of xhci_pci_probe, and decrease it once the usb-3 bus is
ready.
xhci-platform driver is not using usb_hcd_pci_probe to set up
busses and should not need to have it's usage count increased during probe.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c1b70361e upstream.
It was impossible to enumerate on a SuperSpeed (XHCI) host
with alternate setting = 1 due to the wrongly set 'bMaxBurst'
field in the SuperSpeed Endpoint Companion descriptor.
Testcase:
<host> modprobe -r usbtest; modprobe usbtest alt=1
<device> modprobe g_zero
plug device to SuperSpeed port on the host.
Without this patch the host always complains like so
"usb 12-2: Not enough bandwidth for new device state.
usb 12-2: Not enough bandwidth for altsetting 1"
Bug was introduced by commit cf9a08ae in v3.9
Fixes: cf9a08ae5a (usb: gadget: convert source sink and loopback to
new function interface)
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8eb6c653e upstream.
commit 511f3c5 (usb: gadget: udc-core: fix a regression during gadget driver
unbinding) introduced a crash when DEBUG is enabled.
The debug trace in the atmel_usba_stop function made the assumption that the
driver pointer passed in parameter was not NULL, but since the commit above,
such assumption was no longer always true.
This commit now uses the driver pointer stored in udc which fixes this
issue.
[ balbi@ti.com : improved commit log a bit ]
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aba37fd975 upstream.
This makes sure that the name coming out of configfs cannot be used
accidentally as a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2ff864b53 upstream.
The code in hcd-pci.c that matches up EHCI controllers with their
companion UHCI or OHCI controllers assumes that the private drvdata
fields don't get set too early. However, it turns out that this field
gets set by usb_create_hcd(), before hcd-pci expects it, and this can
result in a crash when two controllers are probed in parallel (as can
happen when a new controller card is hotplugged).
The companions_rwsem lock was supposed to prevent this sort of thing,
but usb_create_hcd() is called outside the scope of the rwsem.
A simple solution is to check that the root-hub pointer has been
initialized as well as the drvdata field. This doesn't happen until
usb_add_hcd() is called; that call and the check are both protected by
the rwsem.
This patch should be applied to stable kernels from 3.10 onward.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Stefani Seibold <stefani@seibold.net>
Tested-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9c3f68f3c upstream.
The user-settable knob, low_latency, has been the source of
several BUG reports which stem from flush_to_ldisc() running
in interrupt context. Since 3.12, which added several sleeping
locks (termios_rwsem and buf->lock) to the input processing path,
the frequency of these BUG reports has increased.
Note that changes in 3.12 did not introduce this regression;
sleeping locks were first added to the input processing path
with the removal of the BKL from N_TTY in commit
a88a69c912,
'n_tty: Fix loss of echoed characters and remove bkl from n_tty'
and later in commit 38db89799b,
'tty: throttling race fix'. Since those changes, executing
flush_to_ldisc() in interrupt_context (ie, low_latency set), is unsafe.
However, since most devices do not validate if the low_latency
setting is appropriate for the context (process or interrupt) in
which they receive data, some reports are due to misconfiguration.
Further, serial dma devices for which dma fails, resort to
interrupt receiving as a backup without resetting low_latency.
Historically, low_latency was used to force wake-up the reading
process rather than wait for the next scheduler tick. The
effect was to trim multiple milliseconds of latency from
when the process would receive new data.
Recent tests [1] have shown that the reading process now receives
data with only 10's of microseconds latency without low_latency set.
Remove the low_latency rx steering from tty_flip_buffer_push();
however, leave the knob as an optional hint to drivers that can
tune their rx fifos and such like. Cleanup stale code comments
regarding low_latency.
[1] https://lkml.org/lkml/2014/2/20/434
"Yay.. thats an annoying historical pain in the butt gone."
-- Alan Cox
Reported-by: Beat Bolli <bbolli@ewanet.ch>
Reported-by: Pavel Roskin <proski@gnu.org>
Acked-by: David Sterba <dsterba@suse.cz>
Cc: Grant Edwards <grant.b.edwards@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Hal Murray <murray+fedora@ip-64-139-1-69.sjc.megapath.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 247bf55727.
This commit, together with commit 3804fad454
"USBNET: ax88179_178a: enable tso if usb host supports sg dma" were
origially added to get xHCI 1.0 hosts and usb ethernet ax88179_178a devices
working together with scatter gather. xHCI 1.0 hosts pose some requirement on how transfer
buffers are aligned, setting this requirement for 1.0 hosts caused USB 3.0 mass
storage devices to fail more frequently.
USB 3.0 mass storage devices used to work before 3.14-rc1. Theoretically,
the TD fragment rules could have caused an occasional disk glitch.
Now the devices *will* fail, instead of theoretically failing.
>From a user perspective, this looks like a regression; the USB device obviously
fails on 3.14-rc1, and may sometimes silently fail on prior kernels.
The proper soluition is to implement the TD fragment rules required, but for now
this patch needs to be reverted to get USB 3.0 mass storage devices working at the
level they used to.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DELAY_INIT quirk only reduces the frequency of enumeration failures
with the Logitech HD Pro C920 and C930e webcams, but does not quite
eliminate them. We have found that adding a delay of 100ms between the
first and second Get Configuration request makes the device enumerate
perfectly reliable even after several weeks of extensive testing. The
reasons for that are anyone's guess, but since the DELAY_INIT quirk
already delays enumeration by a whole second, wating for another 10th of
that isn't really a big deal for the one other device that uses it, and
it will resolve the problems with these webcams.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've encountered a rare issue when enumerating two Logitech webcams
after a reboot that doesn't power cycle the USB ports. They are spewing
random data (possibly some leftover UVC buffers) on the second
(full-sized) Get Configuration request of the enumeration phase. Since
the data is random this can potentially cause all kinds of odd behavior,
and since it occasionally happens multiple times (after the kernel
issues another reset due to the garbled configuration descriptor), it is
not always recoverable. Set the USB_DELAY_INIT quirk that seems to work
around the issue.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci_irq() and ehci_hrtimer_func() can deadlock on ehci->lock when
threadirqs option is used. To prevent the deadlock use
spin_lock_irqsave() in ehci_irq().
This change can be reverted when hrtimer callbacks become threaded.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
