commit 117e5e9c4c upstream.
If the bootloader uses the long descriptor format and jumps to
kernel decompressor code, TTBCR may not be in a right state.
Before enabling the MMU, it is required to clear the TTBCR.PD0
field to use TTBR0 for translation table walks.
The commit dbece45894 ("ARM: 7501/1: decompressor:
reset ttbcr for VMSA ARMv7 cores") does the reset of TTBCR.N, but
doesn't consider all the bits for the size of TTBCR.N.
Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to
indicate the use of TTBR0 and the correct base address width.
Fixes: dbece45894 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d248220f04 upstream.
Since commit 6ce0d20016 ("ARM: dma: Use dma_pfn_offset for dma address translation"),
dma_to_pfn() already returns the PFN with the physical memory start offset
so we don't need to add it again.
This fixes USB mass storage lock-up problem on systems that can't do DMA
over the entire physical memory range (e.g.) Keystone 2 systems with 4GB RAM
can only do DMA over the first 2GB. [K2E-EVM].
What happens there is that without this patch SCSI layer sets a wrong
bounce buffer limit in scsi_calculate_bounce_limit() for the USB mass
storage device. dma_max_pfn() evaluates to 0x8fffff and bounce_limit
is set to 0x8fffff000 whereas maximum DMA'ble physical memory on Keystone 2
is 0x87fffffff. This results in non DMA'ble pages being given to the
USB controller and hence the lock-up.
NOTE: in the above case, USB-SCSI-device's dma_pfn_offset was showing as 0.
This should have really been 0x780000 as on K2e, LOWMEM_START is 0x80000000
and HIGHMEM_START is 0x800000000. DMA zone is 2GB so dma_max_pfn should be
0x87ffff. The incorrect dma_pfn_offset for the USB storage device is because
USB devices are not correctly inheriting the dma_pfn_offset from the
USB host controller. This will be fixed by a separate patch.
Fixes: 6ce0d20016 ("ARM: dma: Use dma_pfn_offset for dma address translation")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 06dfe5cc0c upstream.
SA1111 PCMCIA was broken when PCMCIA switched to using dev_pm_ops for
the PCMCIA socket class. PCMCIA used to handle suspend/resume via the
socket hosting device, which happened at normal device suspend/resume
time.
However, the referenced commit changed this: much of the resume now
happens much earlier, in the noirq resume handler of dev_pm_ops.
However, on SA1111, the PCMCIA device is not accessible as the SA1111
has not been resumed at _noirq time. It's slightly worse than that,
because the SA1111 has already been put to sleep at _noirq time, so
suspend doesn't work properly.
Fix this by converting the core SA1111 code to use dev_pm_ops as well,
and performing its own suspend/resume at noirq time.
This fixes these errors in the kernel log:
pcmcia_socket pcmcia_socket0: time out after reset
pcmcia_socket pcmcia_socket1: time out after reset
and the resulting lack of PCMCIA cards after a S2RAM cycle.
Fixes: d7646f7632 ("pcmcia: use dev_pm_ops for class pcmcia_socket_class")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 293f293637 upstream.
On arm/arm64, we depend on the kvm_unmap_hva* callbacks (via
mmu_notifiers::invalidate_*) to unmap the stage2 pagetables when
the userspace buffer gets unmapped. However, when the Hypervisor
process exits without explicit unmap of the guest buffers, the only
notifier we get is kvm_arch_flush_shadow_all() (via mmu_notifier::release
) which does nothing on arm. Later this causes us to access pages that
were already released [via exit_mmap() -> unmap_vmas()] when we actually
get to unmap the stage2 pagetable [via kvm_arch_destroy_vm() ->
kvm_free_stage2_pgd()]. This triggers crashes with CONFIG_DEBUG_PAGEALLOC,
which unmaps any free'd pages from the linear map.
[ 757.644120] Unable to handle kernel paging request at virtual address
ffff800661e00000
[ 757.652046] pgd = ffff20000b1a2000
[ 757.655471] [ffff800661e00000] *pgd=00000047fffe3003, *pud=00000047fcd8c003,
*pmd=00000047fcc7c003, *pte=00e8004661e00712
[ 757.666492] Internal error: Oops: 96000147 [#3] PREEMPT SMP
[ 757.672041] Modules linked in:
[ 757.675100] CPU: 7 PID: 3630 Comm: qemu-system-aar Tainted: G D
4.8.0-rc1 #3
[ 757.683240] Hardware name: AppliedMicro X-Gene Mustang Board/X-Gene Mustang Board,
BIOS 3.06.15 Aug 19 2016
[ 757.692938] task: ffff80069cdd3580 task.stack: ffff8006adb7c000
[ 757.698840] PC is at __flush_dcache_area+0x1c/0x40
[ 757.703613] LR is at kvm_flush_dcache_pmd+0x60/0x70
[ 757.708469] pc : [<ffff20000809dbdc>] lr : [<ffff2000080b4a70>] pstate: 20000145
...
[ 758.357249] [<ffff20000809dbdc>] __flush_dcache_area+0x1c/0x40
[ 758.363059] [<ffff2000080b6748>] unmap_stage2_range+0x458/0x5f0
[ 758.368954] [<ffff2000080b708c>] kvm_free_stage2_pgd+0x34/0x60
[ 758.374761] [<ffff2000080b2280>] kvm_arch_destroy_vm+0x20/0x68
[ 758.380570] [<ffff2000080aa330>] kvm_put_kvm+0x210/0x358
[ 758.385860] [<ffff2000080aa524>] kvm_vm_release+0x2c/0x40
[ 758.391239] [<ffff2000082ad234>] __fput+0x114/0x2e8
[ 758.396096] [<ffff2000082ad46c>] ____fput+0xc/0x18
[ 758.400869] [<ffff200008104658>] task_work_run+0x108/0x138
[ 758.406332] [<ffff2000080dc8ec>] do_exit+0x48c/0x10e8
[ 758.411363] [<ffff2000080dd5fc>] do_group_exit+0x6c/0x130
[ 758.416739] [<ffff2000080ed924>] get_signal+0x284/0xa18
[ 758.421943] [<ffff20000808a098>] do_signal+0x158/0x860
[ 758.427060] [<ffff20000808aad4>] do_notify_resume+0x6c/0x88
[ 758.432608] [<ffff200008083624>] work_pending+0x10/0x14
[ 758.437812] Code: 9ac32042 8b010001 d1000443 8a230000 (d50b7e20)
This patch fixes the issue by moving the kvm_free_stage2_pgd() to
kvm_arch_flush_shadow_all().
Tested-by: Itaru Kitayama <itaru.kitayama@riken.jp>
Reported-by: Itaru Kitayama <itaru.kitayama@riken.jp>
Reported-by: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit da60626e7d upstream.
Clear the current reset status prior to rebooting the platform. This
adds the bit missing from 04fef228fb ("[ARM] pxa: introduce
reset_status and clear_reset_status for driver's usage").
Fixes: 04fef228fb ("[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a778937888 upstream.
Commit 148c274ea6 ("ARM: kirkwood: ib62x0: add u-boot environment
partition") split the "u-boot" partition into "u-boot" and "u-boot
environment". However, instead of the size of the environment, an offset
was given, resulting in overlapping partitions.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Fixes: 148c274ea6 ("ARM: kirkwood: ib62x0: add u-boot environment partition")
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Luka Perkov <luka@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7de249964f upstream.
Add access checks to sys_oabi_epoll_wait() and sys_oabi_semtimedop().
This fixes CVE-2016-3857, a local privilege escalation under
CONFIG_OABI_COMPAT.
Reported-by: Chiachih Wu <wuchiachih@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Dave Weinstein <olorin@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b46211d6dc upstream.
Add missing sysconfig/sysstatus information
to OMAP3 hwmod. The information has been
checked against OMAP34xx and OMAP36xx TRM.
Without this change DSI block is not reset
during boot, which is required for working
Nokia N950 display.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f127089650 upstream.
When a L2 cache controller is used in a system that provides hardware
coherency, the entire outer cache operations are useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
In the current kernel implementation, the outer cache flush range
operation is triggered by the dma_alloc function.
This operation can be take place during runtime and in some
circumstances may lead to the PCIe/PL310 deadlock on Armada 375/38x
SoCs.
This patch extends the __dma_clear_buffer() function to receive a
boolean argument related to the coherency of the system. The same
things is done for the calling functions.
Reported-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[bwh: Backported to 3.16:
- Drop changes to struct arm_dm_alloc_args, cma_allocator_alloc()
- Pass the new parameter to __alloc_from_contiguous() from __dma_alloc()
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b00ccf5b68 upstream.
pruss hwmod RSTST register wrongly points to PWRSTCTRL register in case of
am43xx. Fix the RSTST register offset value.
This can lead to setting of wrong power state values for PER domain.
Fixes: 1c7e224d ("ARM: OMAP2+: hwmod: AM335x: runtime register update")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c5379ba8fc upstream.
Until now, our understanding for HW I/O coherency to work on the
Cortex-A9 based Marvell SoC was that only the PCIe regions should be
mapped strongly-ordered. However, we were still encountering some
deadlocks, especially when testing the CESA crypto engine. After
checking with the HW designers, it was concluded that all the MMIO
registers should be mapped as strongly ordered for the HW I/O coherency
mechanism to work properly.
This fixes some easy to reproduce deadlocks with the CESA crypto engine
driver (dmcrypt on a sufficiently large disk partition).
Tested-by: Terry Stockert <stockert@inkblotadmirer.me>
Tested-by: Romain Perier <romain.perier@free-electrons.com>
Cc: Terry Stockert <stockert@inkblotadmirer.me>
Cc: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 591d215afc upstream.
kvm provides kvm_vcpu_uninit(), which amongst other things, releases the
last reference to the struct pid of the task that was last running the vcpu.
On arm64 built with CONFIG_DEBUG_KMEMLEAK, starting a guest with kvmtool,
then killing it with SIGKILL results (after some considerable time) in:
> cat /sys/kernel/debug/kmemleak
> unreferenced object 0xffff80007d5ea080 (size 128):
> comm "lkvm", pid 2025, jiffies 4294942645 (age 1107.776s)
> hex dump (first 32 bytes):
> 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> backtrace:
> [<ffff8000001b30ec>] create_object+0xfc/0x278
> [<ffff80000071da34>] kmemleak_alloc+0x34/0x70
> [<ffff80000019fa2c>] kmem_cache_alloc+0x16c/0x1d8
> [<ffff8000000d0474>] alloc_pid+0x34/0x4d0
> [<ffff8000000b5674>] copy_process.isra.6+0x79c/0x1338
> [<ffff8000000b633c>] _do_fork+0x74/0x320
> [<ffff8000000b66b0>] SyS_clone+0x18/0x20
> [<ffff800000085cb0>] el0_svc_naked+0x24/0x28
> [<ffffffffffffffff>] 0xffffffffffffffff
On x86 kvm_vcpu_uninit() is called on the path from kvm_arch_destroy_vm(),
on arm no equivalent call is made. Add the call to kvm_arch_vcpu_free().
Signed-off-by: James Morse <james.morse@arm.com>
Fixes: 749cf76c5a ("KVM: ARM: Initial skeleton to compile KVM support")
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8f50b8e574 upstream.
In the omap gpmc driver it can be noticed that GPMC_CONFIG4_OEEXTRADELAY
is overwritten by the WEEXTRADELAY value from the device tree and
GPMC_CONFIG4_WEEXTRADELAY is not updated by the value from the device
tree.
As a consequence, the memory accesses cannot be configured properly when
the extra delay are needed for OE and WE.
Fix the update of GPMC_CONFIG4_WEEXTRADELAY with the value from the
device tree file and prevents GPMC_CONFIG4_OEXTRADELAY
being overwritten by the WEXTRADELAY value from the device tree.
Signed-off-by: Ocquidant, Sebastien <sebastienocquidant@eaton.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 56530f5d2d upstream.
Currently pmd_mknotpresent will use a zero entry to respresent an
invalidated pmd.
Unfortunately this definition clashes with pmd_none, thus it is
possible for a race condition to occur if zap_pmd_range sees pmd_none
whilst __split_huge_pmd_locked is running too with pmdp_invalidate
just called.
This patch fixes the race condition by modifying pmd_mknotpresent to
create non-zero faulting entries (as is done in other architectures),
removing the ambiguity with pmd_none.
[catalin.marinas@arm.com: using L_PMD_SECT_VALID instead of PMD_TYPE_SECT]
Fixes: 8d96250700 ("ARM: mm: Transparent huge page support for LPAE systems.")
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[bwh: Backported to 3.16: also convert from a macro to a function, as done
earlier upstream]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6245318869 upstream.
In a subsequent patch, pmd_mknotpresent will clear the valid bit of the
pmd entry, resulting in a not-present entry from the hardware's
perspective. Unfortunately, pmd_present simply checks for a non-zero pmd
value and will therefore continue to return true even after a
pmd_mknotpresent operation. Since pmd_mknotpresent is only used for
managing huge entries, this is only an issue for the 3-level case.
This patch fixes the 3-level pmd_present implementation to take into
account the valid bit. For bisectability, the change is made before the
fix to pmd_mknotpresent.
[catalin.marinas@arm.com: comment update regarding pmd_mknotpresent patch]
Fixes: 8d96250700 ("ARM: mm: Transparent huge page support for LPAE systems.")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steve Capper <Steve.Capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e2dfb4b880 upstream.
PTRACE_SETVFPREGS fails to properly mark the VFP register set to be
reloaded, because it undoes one of the effects of vfp_flush_hwstate().
Specifically vfp_flush_hwstate() sets thread->vfpstate.hard.cpu to
an invalid CPU number, but vfp_set() overwrites this with the original
CPU number, thereby rendering the hardware state as apparently "valid",
even though the software state is more recent.
Fix this by reverting the previous change.
Fixes: 8130b9d7b9 ("ARM: 7308/1: vfp: flush thread hwstate before copying ptrace registers")
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Simon Marchi <simon.marchi@ericsson.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d4b9e0790a upstream.
The ARM architecture mandates that when changing a page table entry
from a valid entry to another valid entry, an invalid entry is first
written, TLB invalidated, and only then the new entry being written.
The current code doesn't respect this, directly writing the new
entry and only then invalidating TLBs. Let's fix it up.
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c20c8f750d upstream.
The omap_hwmod _enable() function can return success without setting
the hwmod state to _HWMOD_STATE_ENABLED for IPs with reset lines when
all of the reset lines are asserted. The omap_hwmod _idle() function
also performs a similar check, but after checking for the hwmod state
first. This triggers the WARN when pm_runtime_get and pm_runtime_put
are invoked on IPs with all reset lines asserted. Reverse the checks
for hwmod state and reset lines status to fix this.
Issue found during a unbind operation on a device with reset lines
still asserted, example backtrace below
------------[ cut here ]------------
WARNING: CPU: 1 PID: 879 at arch/arm/mach-omap2/omap_hwmod.c:2207 _idle+0x1e4/0x240()
omap_hwmod: mmu_dsp: idle state can only be entered from enabled state
Modules linked in:
CPU: 1 PID: 879 Comm: sh Not tainted 4.4.0-00008-ga989d951331a #3
Hardware name: Generic OMAP5 (Flattened Device Tree)
[<c0018e60>] (unwind_backtrace) from [<c0014dc4>] (show_stack+0x10/0x14)
[<c0014dc4>] (show_stack) from [<c037ac28>] (dump_stack+0x90/0xc0)
[<c037ac28>] (dump_stack) from [<c003f420>] (warn_slowpath_common+0x78/0xb4)
[<c003f420>] (warn_slowpath_common) from [<c003f48c>] (warn_slowpath_fmt+0x30/0x40)
[<c003f48c>] (warn_slowpath_fmt) from [<c0028c20>] (_idle+0x1e4/0x240)
[<c0028c20>] (_idle) from [<c0029080>] (omap_hwmod_idle+0x28/0x48)
[<c0029080>] (omap_hwmod_idle) from [<c002a5a4>] (omap_device_idle+0x3c/0x90)
[<c002a5a4>] (omap_device_idle) from [<c0427a90>] (__rpm_callback+0x2c/0x60)
[<c0427a90>] (__rpm_callback) from [<c0427ae4>] (rpm_callback+0x20/0x80)
[<c0427ae4>] (rpm_callback) from [<c0427f84>] (rpm_suspend+0x138/0x74c)
[<c0427f84>] (rpm_suspend) from [<c0428b78>] (__pm_runtime_idle+0x78/0xa8)
[<c0428b78>] (__pm_runtime_idle) from [<c041f514>] (__device_release_driver+0x64/0x100)
[<c041f514>] (__device_release_driver) from [<c041f5d0>] (device_release_driver+0x20/0x2c)
[<c041f5d0>] (device_release_driver) from [<c041d85c>] (unbind_store+0x78/0xf8)
[<c041d85c>] (unbind_store) from [<c0206df8>] (kernfs_fop_write+0xc0/0x1c4)
[<c0206df8>] (kernfs_fop_write) from [<c018a120>] (__vfs_write+0x20/0xdc)
[<c018a120>] (__vfs_write) from [<c018a9cc>] (vfs_write+0x90/0x164)
[<c018a9cc>] (vfs_write) from [<c018b1f0>] (SyS_write+0x44/0x9c)
[<c018b1f0>] (SyS_write) from [<c0010420>] (ret_fast_syscall+0x0/0x1c)
---[ end trace a4182013c75a9f50 ]---
While at this, fix the sequence in _shutdown() as well, though there
is no easy reproducible scenario.
Fixes: 747834ab83 ("ARM: OMAP2+: hwmod: revise hardreset behavior")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9ec423ed62 upstream.
Commit be3d7d023b ("ARM: kirkwood: Add DTS file for NSA320")
created the new file kirkwood-nsa320.dts but did not
add it to the Makefile.
Fixes: be3d7d023b ("ARM: kirkwood: Add DTS file for NSA320")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fc5c796e12 upstream.
Commit 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology
NAS devices") created the new file kirkwood-ds112.dts but did not
add it to the Makefile.
Fixes: 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology NAS devices")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5616f36713 upstream.
The secondary CPU starts up in ARM mode. When the kernel is compiled in
thumb2 mode we have to explicitly compile the secondary startup
trampoline in ARM mode, otherwise the CPU will go to Nirvana.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3ca4a23810 upstream.
Commit 127500ccb7 ("ARM: OMAP2+: Only write the sysconfig on idle
when necessary") talks about verification of sysconfig cache value before
updating it, only during idle path. But the patch is adding the
verification in the enable path. So, adding the check in a proper place
as per the commit description.
Not keeping this check during enable path as there is a chance of losing
context and it is safe to do on idle as the context of the register will
never be lost while the device is active.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: commit 127500ccb7 "ARM: OMAP2+: Only write the sysconfig on idle when necessary"
[paul@pwsan.com: appears to have been caused by my own mismerge of the
originally posted patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 127500ccb7 upstream.
Currently, whenever we idle a device _idle_sysc() is called and writes to the
devices SYSCONFIG register to set the idle mode. A lot devices are using the
smart-idle mode and so the write to the SYSCONFIG register is programming the
same value that is already stored in the register.
Writes to the devices SYSCONFIG register can be slow, for example, writing to
the DMTIMER SYSCONFIG register takes 3 interface clock cycles and 3 functional
clock cycles. If the DMTIMER is using the slow 32kHz functional clock this can
take ~100us.
Furthermore, during boot on an OMAP4430 panda board, I see that there are 100
calls to _idle_sysc(), however, only 3 out of the 100 calls actually write
the SYSCONFIG register with a new value.
Therefore, to avoid unnecessary writes to device SYSCONFIG registers when
idling the device, only write the value if the value has changed. It should be
safe to do this on idle as the context of the register will never be lost while
the device is active.
Verified that suspend, CORE off and retention states are working with this
change on OMAP3430 Beagle board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 98f4222150 upstream.
Based on CPU type choose generic omap3 or omap3430 specific cpuidle
parameters. Parameters for omap3430 were measured on Nokia N900 device and
added by commit 5a1b1d3a9e ("OMAP3: RX-51: Pass cpu idle parameters")
which were later removed by commit 231900afba ("ARM: OMAP3: cpuidle -
remove rx51 cpuidle parameters table") due to huge code complexity.
This patch brings cpuidle parameters for omap3430 devices again, but uses
simple condition based on CPU type.
Fixes: 231900afba ("ARM: OMAP3: cpuidle - remove rx51 cpuidle
parameters table")
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8e58041114 upstream.
The davinci platform has tried to get support for the EEPROM right,
but failed to get a clean build so far. At the moment, we get
a warning whenever CONFIG_SYSFS is disabled, as that is needed by
EEPROM_AT24:
warning: (MACH_DAVINCI_EVM && MACH_SFFSDR && MACH_DAVINCI_DM6467_EVM && MACH_DAVINCI_DM365_EVM && MACH_DAVINCI_DA830_EVM && MACH_MITYOMAPL138 && MACH_MINI2440) selects EEPROM_AT24 which has unmet direct dependencies (I2C && SYSFS)
Kevin Hilman initially added the 'select' to ensure that EEPROM_AT24
is always enabled in machines that really want it for normal operation
(i.e. for reading the MAC address). This broke when I2C was disabled,
and Russell King followed up with another patch to select that as
well.
I now see that the SYSFS dependency is still missing, which leaves
us with three options:
a) add 'select SYSFS' in addition to the others
b) change AT24_EEPPROM to work without sysfs (should be possible)
c) remove all those selects again and get the files to build when
I2C is disabled.
I would really hate to do a) because adding select statements that
hardwire user-selectable symbols is generally a bad idea. I first
tried b) but then ended up redoing the patch from scratch to approach
c), so we can also remove the other selects.
I checked that CONFIG_I2C is still enabled with davinci_all_defconfig,
so that does not have to change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 45b146d746 ("ARM: Davinci: Fix I2C build errors")
Fixes: 22ca466847 ("davinci: kconfig: select at24 eeprom for selected boards")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b3a7f31eb7 upstream.
The Armada 375 has the same SATA IP as Armada 370 and Armada XP, which
requires the PHY speed to be set in the LP_PHY_CTL register for SATA
hotplug to work.
Therefore, this commit updates the compatible string used to describe
the SATA IP in Armada 375 from marvell,orion-sata to
marvell,armada-370-sata.
Fixes: 4de5908509 ("ARM: mvebu: add Device Tree description of the Armada 375 SoC")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4cad67fca3 upstream.
Calling return copy_to_user(...) in an ioctl will not
do the right thing if there's a pagefault:
copy_to_user returns the number of bytes not copied
in this case.
Fix up kvm to do
return copy_to_user(...)) ? -EFAULT : 0;
everywhere.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[ luis: backported to 3.16:
- dropped changes to arch/arm64/kvm/guest.c ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9d021c9d1b upstream.
Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.
Hence each dts in the Linux kernel should provide a unique model
identifier.
Commit 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology NAS
devices") created the new files kirkwood-ds111.dts and kirkwood-ds112.dts
using the same model identifier.
This patch provides a unique model identifier for the
Synology DiskStation DS112.
Fixes: 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology NAS devices")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e972c37459 upstream.
Since the dawn of time the ICST code has only supported divide
by one or hang in an eternal loop. Luckily we were always dividing
by one because the reference frequency for the systems using
the ICSTs is 24MHz and the [min,max] values for the PLL input
if [10,320] MHz for ICST307 and [6,200] for ICST525, so the loop
will always terminate immediately without assigning any divisor
for the reference frequency.
But for the code to make sense, let's insert the missing i++
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5070fb14a0 upstream.
When trying to set the ICST 307 clock to 25174000 Hz I ran into
this arithmetic error: the icst_hz_to_vco() correctly figure out
DIVIDE=2, RDW=100 and VDW=99 yielding a frequency of
25174000 Hz out of the VCO. (I replicated the icst_hz() function
in a spreadsheet to verify this.)
However, when I called icst_hz() on these VCO settings it would
instead return 4122709 Hz. This causes an error in the common
clock driver for ICST as the common clock framework will call
.round_rate() on the clock which will utilize icst_hz_to_vco()
followed by icst_hz() suggesting the erroneous frequency, and
then the clock gets set to this.
The error did not manifest in the old clock framework since
this high frequency was only used by the CLCD, which calls
clk_set_rate() without first calling clk_round_rate() and since
the old clock framework would not call clk_round_rate() before
setting the frequency, the correct values propagated into
the VCO.
After some experimenting I figured out that it was due to a simple
arithmetic overflow: the divisor for 24Mhz reference frequency
as reference becomes 24000000*2*(99+8)=0x132212400 and the "1"
in bit 32 overflows and is lost.
But introducing an explicit 64-by-32 bit do_div() and casting
the divisor into (u64) we get the right frequency back, and the
right frequency gets set.
Tested on the ARM Versatile.
Cc: linux-clk@vger.kernel.org
Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 55795ef546 upstream.
The SKF_AD_ALU_XOR_X ancillary is not like the other ancillary data
instructions since it XORs A with X while all the others replace A with
some loaded value. All the BPF JITs fail to clear A if this is used as
the first instruction in a filter. This was found using american fuzzy
lop.
Add a helper to determine if A needs to be cleared given the first
instruction in a filter, and use this in the JITs. Except for ARM, the
rest have only been compile-tested.
Fixes: 3480593131 ("net: filter: get rid of BPF_S_* enum")
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 0f090bf14e upstream.
Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver
is already in the kernel, this node enables the controller support for
WM8650
Signed-off-by: Roman Volkov <rvolkov@v1ros.org>
Reviewed-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 76cc404bfd upstream.
Reviewed-by: Jeff Layton <jeff.layton@primarydata.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3a35e470bc upstream.
Gateworks Ventana boards seem to need "RGMII-ID" (internal delay)
PHY mode, instead of simple "RGMII", for their Marvell 88E1510
transceiver. Otherwise, the Ethernet MAC doesn't work with Marvell PHY
driver (TX doesn't seem to work correctly).
Tested on GW5400 rev. C.
This bug affects ARM Fedora 23.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit fa0708b320 upstream.
In cpu_v7_do_suspend routine, r11 is used while it is NOT
saved/restored, different compiler may have different usage
of ARM general registers, so it may cause issues during
calling cpu_v7_do_suspend.
We meet kernel fault occurs when using GCC 4.8.3, r11 contains
valid value before calling into cpu_v7_do_suspend, but when returned
from this routine, r11 is corrupted and lead to kernel fault.
Doing save/restore for those corrupted registers is a must in
assemble code.
Signed-off-by: Anson Huang <Anson.Huang@freescale.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5442f0eadf upstream.
The "reg" entry in the "poweroff" section of "kirkwood-ts219.dtsi"
addressed the wrong uart (0 = console). This patch changes the address
to select uart 1, which is the uart connected to the pic
microcontroller, which can switch the device off.
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 4350a47bba ("ARM: Kirkwood: Make use of the QNAP Power off driver.")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 54c09889bf upstream.
The z2 machine calls pxa27x_set_pwrmode() in order to power off
the machine, but this function gets discarded early at boot because
it is marked __init, as pointed out by kbuild:
WARNING: vmlinux.o(.text+0x145c4): Section mismatch in reference from the function z2_power_off() to the function .init.text:pxa27x_set_pwrmode()
The function z2_power_off() references
the function __init pxa27x_set_pwrmode().
This is often because z2_power_off lacks a __init
annotation or the annotation of pxa27x_set_pwrmode is wrong.
This removes the __init section modifier to fix rebooting and the
build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ba4a90a6d8 ("ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 696d8b70c0 upstream.
In case when the interrupt happened for the second eDMA the channel
number was incorrectly passed to the client driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 7e31210349 upstream.
IOMMU-based dma_mmap() implementation lacked proper support for offset
parameter used in mmap call (it always assumed that mapping starts from
offset zero). This patch adds support for offset parameter to IOMMU-based
implementation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 371f0f085f upstream.
dma_mmap() function in IOMMU-based dma-mapping implementation lacked
a check for valid range of mmap parameters (offset and buffer size), what
might have caused access beyond the allocated buffer. This patch fixes
this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d836ace65e upstream.
DSA expects the host_dev pointer to be the device structure associated
with the MDIO bus controller driver. First commit breaking that was
c3a07134e6 ("mv643xx_eth: convert to use the Marvell Orion MDIO
driver"), and then, it got completely under the radar for a while.
Reported-by: Frans van de Wiel <fvdw@fvdw.eu>
Fixes: c3a07134e6 ("mv643xx_eth: convert to use the Marvell Orion MDIO driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
This reverts commit b5614b199b,
which was commit 5be9fc23cd upstream.
Ben Hutchings pointed out this was not applicable to the 3.16-ckt kernel.
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Benjamin Cama <benoar@dolka.fr>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 1dbdad7507 upstream.
The i2c5 pinctrl offsets are wrong. If the bootloader doesn't set the
pins up, communication with tca6424a doesn't work (controller timeouts)
and it is not possible to enable HDMI.
Fixes: 9be495c426 ("ARM: dts: omap5-evm: Add I2c pinctrl data")
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3a2fa775bd upstream.
Let's fix pinmux address of gpio 170 used by tfp410 powerdown-gpio.
According to the OMAP35x Technical Reference Manual
CONTROL_PADCONF_I2C3_SDA[15:0] 0x480021C4 mode0: i2c3_sda
CONTROL_PADCONF_I2C3_SDA[31:16] 0x480021C4 mode4: gpio_170
the pinmux address of gpio 170 must be 0x480021C6.
The former wrong address broke i2c3 (used by hdmi ddc), resulting in
kernel message:
omap_i2c 48060000.i2c: controller timed out
Fixes: 8cecf52bef ("ARM: omap3-beagle.dts: add display information")
Signed-off-by: Carl Frederik Werner <frederik@cfbw.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 688bc577ac upstream.
When running a guest with the architected timer disabled (with QEMU and
the kernel_irqchip=off option, for example), it is important to make
sure the timer gets turned off. Otherwise, the guest may try to
enable it anyway, leading to a screaming HW interrupt.
The fix is to unconditionally turn off the virtual timer on guest
exit.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9b55613f42 upstream.
When a kernel is built covering ARMv6 to ARMv7, we omit to clear the
IT state when entering a signal handler. This can cause the first
few instructions to be conditionally executed depending on the parent
context.
In any case, the original test for >= ARMv7 is broken - ARMv6 can have
Thumb-2 support as well, and an ARMv6T2 specific build would omit this
code too.
Relax the test back to ARMv6 or greater. This results in us always
clearing the IT state bits in the PSR, even on CPUs where these bits
are reserved. However, they're reserved for the IT state, so this
should cause no harm.
Fixes: d71e1352e2 ("Clear the IT state when invoking a Thumb-2 signal handler")
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a077224fd3 upstream.
While working on the 32-bit ARM port of UEFI, I noticed a strange
corruption in the kernel log. The following snprintf() statement
(in drivers/firmware/efi/efi.c:efi_md_typeattr_format())
snprintf(pos, size, "|%3s|%2s|%2s|%2s|%3s|%2s|%2s|%2s|%2s]",
was producing the following output in the log:
| | | | | |WB|WT|WC|UC]
| | | | | |WB|WT|WC|UC]
| | | | | |WB|WT|WC|UC]
|RUN| | | | |WB|WT|WC|UC]*
|RUN| | | | |WB|WT|WC|UC]*
| | | | | |WB|WT|WC|UC]
|RUN| | | | |WB|WT|WC|UC]*
| | | | | |WB|WT|WC|UC]
|RUN| | | | | | | |UC]
|RUN| | | | | | | |UC]
As it turns out, this is caused by incorrect code being emitted for
the string() function in lib/vsprintf.c. The following code
if (!(spec.flags & LEFT)) {
while (len < spec.field_width--) {
if (buf < end)
*buf = ' ';
++buf;
}
}
for (i = 0; i < len; ++i) {
if (buf < end)
*buf = *s;
++buf; ++s;
}
while (len < spec.field_width--) {
if (buf < end)
*buf = ' ';
++buf;
}
when called with len == 0, triggers an issue in the GCC SRA optimization
pass (Scalar Replacement of Aggregates), which handles promotion of signed
struct members incorrectly. This is a known but as yet unresolved issue.
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=65932). In this particular
case, it is causing the second while loop to be executed erroneously a
single time, causing the additional space characters to be printed.
So disable the optimization by passing -fno-ipa-sra.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5be9fc23cd upstream.
Since v3.18, attempts to deliver IRQ0 are rejected, breaking orion5x.
Fix this by increasing all interrupts by one, as did 5d6bed2a9c for
dove. Also, force MULTI_IRQ_HANDLER for all orion platforms (including
dove) as the specific handler is needed to shift back IRQ numbers by
one.
[gregory.clement@free-electrons.com]: moved the select
MULTI_IRQ_HANDLER from PLAT_ORION_LEGACY to ARCH_ORION5X as it broke
the build for dove.
Fixes: a71b092a9c ("ARM: Convert handle_IRQ to use __handle_domain_irq")
Signed-off-by: Benjamin Cama <benoar@dolka.fr>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Detlef Vollmann <dv@vollmann.ch>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b9e23f3219 upstream.
Legacy IPs like PWMSS, present under l4per2_7xx_clkdm, cannot support
smart-idle when its clock domain is in HW_AUTO on DRA7 SoCs. Hence,
program clock domain to SW_WKUP.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
