The dln2-adc driver uses interface(s) that are controlled by the
IIO_TRIGGERED_BUFFER Kconfig symbol, so the driver needs to select
that symbol to prevent the build error.
drivers/iio/adc/dln2-adc.o: In function `dln2_adc_probe':
dln2-adc.c:(.text+0x528): undefined reference to `devm_iio_triggered_buffer_setup'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New GPIO IRQs are allocated and mapped dynamically by default when
GPIO IRQ infrastructure is used by cherryview-pinctrl driver.
This causes issues on some Intel platforms [1][2] with broken BIOS which
hardcodes Linux IRQ numbers in their ACPI tables.
On such platforms cherryview-pinctrl driver should allocate and map all
GPIO IRQs at probe time.
Side effect - "Cannot allocate irq_descs @ IRQ%d, assuming pre-allocated\n"
can be seen at boot log.
NOTE. It still may fail if boot sequence will changed and some interrupt
controller will be probed before cherryview-pinctrl which will shift Linux IRQ
numbering (expected with CONFIG_SPARCE_IRQ enabled).
[1] https://bugzilla.kernel.org/show_bug.cgi?id=194945
[2] https://lkml.org/lkml/2017/9/28/153
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Chris Gorman <chrisjohgorman@gmail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Chris Gorman <chrisjohgorman@gmail.com>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Chris Gorman <chrisjohgorman@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A couple of serious fixes (use after free and blacklist for WRITE
SAME). One error leg fix (write_pending failure) and one user
experience problem (do not override max_sectors_kb) and one minor
unused function removal.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZ2P68AAoJEAVr7HOZEZN48hEP/0d7RH77AjV1smqQHJpel7b8
WFh7zWHfhyHEmDMf1xtepqw1RAsrkXfRy12wOOc3ppnaozBIh1GIvjHRWXtaEIaA
qsTJkROWro3XskxfKL8n0CqeATuk6EjfE+ehRFyXQ9F9yhIB4FxaYROzGUfM9rON
ScD2vHH0sE4PIUiavizjxSk6G4KNvGyqM/xtgUIymH7Dcd7MorOq1WBvGXp7etkG
QSCV1tvB63yg2jcqatANTLO0LuI9N023VGA/QrTLzpu6M54QZwMGAmVwZfkQ1/nO
RLGWTj6jrB4RSF690NN1QLRnf58GYEyIEa37Dlwp/bLyHv4Y9NxO3KB/M0MIf/x2
PJ5FmUw7IwPVzAk6WmGoUIvscDnrDplzVL0fMZKlnW3+8mQav+IIev7sBvPjMkMw
HA7PLNXrEpR1tOBhr9je2V2Jz9KxARZFRUqm238Rq03W6kjYQQbSG+dC06A7o2DQ
UYuXCWp+CZhbBSG29qPf8wzNbdndpkmXatwLrwVmmRn+/eo3BGF5/SfOKu0M8PTu
M4apqkZTZdMAzPckIe0lg6RIJ+F5lWPPX454CZqivM8MFNyjHbf2VJAvQbU9dNhM
dfrPsLogZNgCop13H06xAFS6m3dIP5YqUEo/yWXciC6hnvCP7z6ZkiqHTHJIIJMm
vwQJLkkB2Ex4NscJcZfw
=X/MK
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
- a couple of serious fixes: use after free and blacklist for WRITE
SAME
- one error leg fix: write_pending failure
- one user experience problem: do not override max_sectors_kb
- one minor unused function removal
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvscsis: Fix write_pending failure path
scsi: libiscsi: Remove iscsi_destroy_session
scsi: libiscsi: Fix use-after-free race during iscsi_session_teardown
scsi: sd: Do not override max_sectors_kb sysfs setting
scsi: sd: Implement blacklist option for WRITE SAME w/ UNMAP
Pull i2c fixes from Wolfram Sang:
"I2C has three driver fixes for the newly introduced drivers and one ID
addition for the i801 driver"
* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: make structure stm32f7_setup static const
i2c: ensure termination of *_device_id tables
i2c: i801: Add support for Intel Cedar Fork
i2c: stm32f7: fix setup structure
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just remove
the mmc bounce buffer code altogether, as it has practically no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0WJ+
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
Now acking of edge irqs happens the following way:
- omap_gpio_irq_handler
- "isr" = read irq status
- omap_clear_gpio_irqbank(bank, isr_saved & ~level_mask);
^ clear edge status, so irq can be accepted
- loop while "isr"
generic_handle_irq()
- handle_edge_irq()
- desc->irq_data.chip->irq_ack(&desc->irq_data);
- omap_gpio_ack_irq()
it might be that at this moment edge IRQ was triggered again and it will be
cleared and IRQ will be lost.
Use handle_simple_irq and clear edge interrupts early without disabling them in
omap_gpio_irq_handler to avoid loosing interrupts.
[1] https://marc.info/?l=linux-omap&m=149004465313534&w=2
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gcc warns that the length for the extra unaligned data in the hash
function may be used unaligned. In theory this could happen if
we pass a zero-length sg_list, or if sg_is_last() was never true:
In file included from drivers/crypto/stm32/stm32-hash.c:23:
drivers/crypto/stm32/stm32-hash.c: In function 'stm32_hash_one_request':
include/uapi/linux/kernel.h:12:49: error: 'ncp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
#define __KERNEL_DIV_ROUND_UP(n, d) (((n) + (d) - 1) / (d))
Neither of these can happen in practice, so the warning is harmless.
However while trying to suppress the warning, I noticed multiple
problems with that code:
- On big-endian kernels, we byte-swap the data like we do for
register accesses, however this is a data stream and almost
certainly needs to use a single writesl() instead of series
of writel() to give the correct hash.
- If the length is not a multiple of four bytes, we skip the
last word entirely, since we write the truncated length
using stm32_hash_set_nblw().
- If we change the code to round the length up rather than
down, the last bytes contain stale data, so it needs some
form of padding.
This tries to address all four problems, by correctly
initializing the length to zero, using endian-safe copy
functions, adding zero-padding and passing the padded length.
I have done no testing on this patch, so please review
carefully and if possible test with an unaligned length
and big-endian kernel builds.
Fixes: 8a1012d3f2 ("crypto: stm32 - Support for STM32 HASH module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Suspend fix for Samsung Exynos SoCs where we need to keep clks on
across suspend
- Two critical clk markings for clks that shouldn't ever turn off on
Rockchip SoCs
- A fix for a copy-paste mistake on Rockchip rk3128 causing some clks to
touch the same bit and trample over one another
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=jV1S
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
- build fix to export the clk_bulk_prepare() symbol
- suspend fix for Samsung Exynos SoCs where we need to keep clks on
across suspend
- two critical clk markings for clks that shouldn't ever turn off on
Rockchip SoCs
- a fix for a copy-paste mistake on Rockchip rk3128 causing some clks
to touch the same bit and trample over one another
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: samsung: exynos4: Enable VPLL and EPLL clocks for suspend/resume cycle
clk: Export clk_bulk_prepare()
clk: rockchip: add sclk_timer5 as critical clock on rk3128
clk: rockchip: fix up rk3128 pvtm and mipi_24m gate regs error
clk: rockchip: add pclk_pmu as critical clock on rk3128
Pull block fixes from Jens Axboe:
"A collection of fixes for this series. This contains:
- NVMe pull request from Christoph, one uuid attribute fix, and one
fix for the controller memory buffer address for remapped BARs.
- use-after-free fix for bsg, from Benjamin Block.
- bcache race/use-after-free fix for a list traversal, fixing a
regression in this merge window. From Coly Li.
- null_blk change configfs dependency change from a 'depends' to a
'select'. This is a change from this merge window as well. From me.
- nbd signal fix from Josef, fixing a regression introduced with the
status code changes.
- nbd MAINTAINERS mailing list entry update.
- blk-throttle stall fix from Joseph Qi.
- blk-mq-debugfs fix from Omar, fixing an issue where we don't
register the IO scheduler debugfs directory, if the driver is
loaded with it. Only shows up if you switch through the sysfs
interface"
* 'for-linus' of git://git.kernel.dk/linux-block:
bsg-lib: fix use-after-free under memory-pressure
nvme-pci: Use PCI bus address for data/queues in CMB
blk-mq-debugfs: fix device sched directory for default scheduler
null_blk: change configfs dependency to select
blk-throttle: fix possible io stall when upgrade to max
MAINTAINERS: update list for NBD
nbd: fix -ERESTARTSYS handling
nvme: fix visibility of "uuid" ns attribute
bcache: use llist_for_each_entry_safe() in __closure_wake_up()
In places like fc_rport_recv_plogi_req and fcoe_ctlr_vn_add we always
take the lport disc_mutex lock before the rports mutex
(rp_mutex) lock. Gaurding list_del_rcu(&rdata->peers) with
disc.disc_mutex in fc_rport_work is correct but the rp_mutex lock
can and should to be dropped before taking that lock else results
in a deadlock.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling rmmod() on a FC driver will results in warnings like
WARNING: CPU: 60 PID: 14640 at fs/sysfs/group.c:237 device_del+0x54/0x240()
sysfs group ffffffff81eff140 not found for kobject '3:0:0:3'
The problem here is that during scsi_remove_target() we will iterate
over all devices, but fail to remove any of those as the call to
scsi_device_get() fails the check to module_is_live(). Hence the
devices will not be removed at this point, but all intermediate
structures like fc rport etc. will be. Later on during
scsi_forget_host() the devices are removed for real, but the device
parent is already removed and causes this warning.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Kyle Fortin <kyle.fortin@oracle.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Bring initialisation of user space undefined instruction handling
early (core_initcall) since late_initcall() happens after modprobe in
initramfs is invoked. Similar fix for fpsimd initialisation
- Increase the kernel stack when KASAN is enabled
- Bring the PCI ACS enabling earlier via the
iort_init_platform_devices()
- Fix misleading data abort address printing (decimal vs hex)
-----BEGIN PGP SIGNATURE-----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=Iu63
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Bring initialisation of user space undefined instruction handling
early (core_initcall) since late_initcall() happens after modprobe in
initramfs is invoked. Similar fix for fpsimd initialisation
- Increase the kernel stack when KASAN is enabled
- Bring the PCI ACS enabling earlier via the
iort_init_platform_devices()
- Fix misleading data abort address printing (decimal vs hex)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Ensure fpsimd support is ready before userspace is active
arm64: Ensure the instruction emulation is ready for userspace
arm64: Use larger stacks when KASAN is selected
ACPI/IORT: Fix PCI ACS enablement
arm64: fix misleading data abort decoding
- a fix for iwpm netlink usage
- a fix for error unwinding in mlx5
- two fixes to vlan handling in qedr
- a couple small i40iw fixes
-----BEGIN PGP SIGNATURE-----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=17J/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"This is a pretty small pull request. Only 6 patches in total. There
are no outstanding -rc patches on the mailing list after this pull
request, so only if some new issues are discovered in the remainder of
the rc cycles will you hear from me again.
Summary:
- a fix for iwpm netlink usage
- a fix for error unwinding in mlx5
- two fixes to vlan handling in qedr
- a couple small i40iw fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
i40iw: Fix port number for query QP
i40iw: Add missing memory barriers
RDMA/qedr: Parse vlan priority as sl
RDMA/qedr: Parse VLAN ID correctly and ignore the value of zero
IB/mlx5: Fix label order in error path handling
RDMA/iwpm: Properly mark end of NL messages
ppp_release() tries to ensure that netdevices are unregistered before
decrementing the unit refcount and running ppp_destroy_interface().
This is all fine as long as the the device is unregistered by
ppp_release(): the unregister_netdevice() call, followed by
rtnl_unlock(), guarantee that the unregistration process completes
before rtnl_unlock() returns.
However, the device may be unregistered by other means (like
ppp_nl_dellink()). If this happens right before ppp_release() calling
rtnl_lock(), then ppp_release() has to wait for the concurrent
unregistration code to release the lock.
But rtnl_unlock() releases the lock before completing the device
unregistration process. This allows ppp_release() to proceed and
eventually call ppp_destroy_interface() before the unregistration
process completes. Calling free_netdev() on this partially unregistered
device will BUG():
------------[ cut here ]------------
kernel BUG at net/core/dev.c:8141!
invalid opcode: 0000 [#1] SMP
CPU: 1 PID: 1557 Comm: pppd Not tainted 4.14.0-rc2+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014
Call Trace:
ppp_destroy_interface+0xd8/0xe0 [ppp_generic]
ppp_disconnect_channel+0xda/0x110 [ppp_generic]
ppp_unregister_channel+0x5e/0x110 [ppp_generic]
pppox_unbind_sock+0x23/0x30 [pppox]
pppoe_connect+0x130/0x440 [pppoe]
SYSC_connect+0x98/0x110
? do_fcntl+0x2c0/0x5d0
SyS_connect+0xe/0x10
entry_SYSCALL_64_fastpath+0x1a/0xa5
RIP: free_netdev+0x107/0x110 RSP: ffffc28a40573d88
---[ end trace ed294ff0cc40eeff ]---
We could set the ->needs_free_netdev flag on PPP devices and move the
ppp_destroy_interface() logic in the ->priv_destructor() callback. But
that'd be quite intrusive as we'd first need to unlink from the other
channels and units that depend on the device (the ones that used the
PPPIOCCONNECT and PPPIOCATTACH ioctls).
Instead, we can just let the netdevice hold a reference on its
ppp_file. This reference is dropped in ->priv_destructor(), at the very
end of the unregistration process, so that neither ppp_release() nor
ppp_disconnect_channel() can call ppp_destroy_interface() in the interim.
Reported-by: Beniamino Galvani <bgalvani@redhat.com>
Fixes: 8cb775bc0a ("ppp: fix device unregistration upon netns deletion")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nine small fixes, really nothing that stands out.
A work around for a spurious MCE on Power9. A CXL fault handling fix, some fixes
to the new XIVE code, and a fix to the new 32-bit STRICT_KERNEL_RWX code.
Fixes for old code/stable: an fix to an incorrect TLB flush on boot but not on
any current machines, a compile error on 4xx and a fix to memory hotplug when
using radix (Power9).
Thanks to:
Anton Blanchard, Cédric Le Goater, Christian Lamparter, Christophe Leroy,
Christophe Lombard, Guenter Roeck, Jeremy Kerr, Michael Neuling, Nicholas
Piggin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=etbe
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Nine small fixes, really nothing that stands out.
A work-around for a spurious MCE on Power9. A CXL fault handling fix,
some fixes to the new XIVE code, and a fix to the new 32-bit
STRICT_KERNEL_RWX code.
Fixes for old code/stable: an fix to an incorrect TLB flush on boot
but not on any current machines, a compile error on 4xx and a fix to
memory hotplug when using radix (Power9).
Thanks to: Anton Blanchard, Cédric Le Goater, Christian Lamparter,
Christophe Leroy, Christophe Lombard, Guenter Roeck, Jeremy Kerr,
Michael Neuling, Nicholas Piggin"
* tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Increase memory block size to 1GB on radix
powerpc/mm: Call flush_tlb_kernel_range with interrupts enabled
powerpc/xive: Clear XIVE internal structures when a CPU is removed
powerpc/xive: Fix IPI reset
powerpc/4xx: Fix compile error with 64K pages on 40x, 44x
powerpc: Fix action argument for cpufeatures-based TLB flush
cxl: Fix memory page not handled
powerpc: Fix workaround for spurious MCE on POWER9
powerpc: Handle MCE on POWER9 with only DSISR bit 30 set
-----BEGIN PGP SIGNATURE-----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=mn3h
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.14-rc4' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Some i915 fixes from the last two weeks (as they were on a strange
base and I just waited for rc3), also a single sun4i hdmi fix"
* tag 'drm-fixes-for-v4.14-rc4' of git://people.freedesktop.org/~airlied/linux:
drm/i915/glk: Fix DMC/DC state idleness calculation
drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
drm/i915: Fix DDI PHY init if it was already on
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
drm/i915/bios: ignore HDMI on port A
drm/i915: remove redundant variable hw_check
drm/i915: always update ELD connector type after get modes
The driver currently handles two NVM formats,
one for 7000 family and below, and one for 8000 family and above.
The 3168 series uses something in between,
so currently the driver uses incorrect offsets for it.
Fix the incorrect offsets.
Fixes: c4836b056d ("iwlwifi: Add PCI IDs for the new 3168 series")
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current channel flags printing is very strange and messy,
in LAR we sometimes print the channel number and sometimes the
frequency, in both we print a calculated value (whether ad-hoc
is supported or not) etc.
Unify all this to
* print the channel number, not the frequency
* remove the band print (2.4/5.2 GHz, it's obvious)
* remove the calculated Ad-Hoc print
Doing all of this also gets the length of the string to a max
of 101 characters, which is below the max of 110 for tracing,
and thus avoids the warning that came up on certain channels
with certain flag combinations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It seems that libsensors treats -EIO as a special non-recoverable
failure when it tries to read the temperature while the firmware is
not running. To solve that, change the error code to a milder
-ENODATA.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196941
Fixes: c221daf219 ("iwlwifi: mvm: add registration to thermal zone")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Today we stop the device and the DMA without stopping the dbgc
recording before. This causes host crashes when the DMA
rate is high.
Stop dbgc recording when clearing the fw debug configuration
to fix this.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In monitor mode we are not expected to decrypt encrypted
packets (not having the keys).
Hence we are expected to get an unknown rx security status.
Keeping the print in monitor mode causes a print for each
captured packet flooding the dmesg.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One bugfix in sun4i for 4.14
* tag 'drm-misc-fixes-2017-10-05' of git://anongit.freedesktop.org/git/drm-misc:
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
drm/i915 fixes for 4.14-rc4:
All 3 highest GLK bugs fixed by Imre:
- GLK drv reload - Fix DDI Phy init if it was already on.
- GLK suspend resume - Reprogram DMC firmware after s3/s4.
- GLK DC states - Fix idleness calculation.
* tag 'drm-intel-fixes-2017-10-04' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915/glk: Fix DMC/DC state idleness calculation
drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
drm/i915: Fix DDI PHY init if it was already on
end of the 'DM_LIST_DEVICES' ioctl.
- A couple stable fixes for the DM crypt target.
- A DM raid health status reporting fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ1pR1AAoJEMUj8QotnQNa48kIAJ+HTqeNjVhspxqKyJHPl78W
3N/B11dWJ/CQ4xN7tbpC2gmsbnBBHE8RFTJzk3xQo7yoKsD0muqH35n0XA7X2A29
i7DoYro/7F6ZuPlgzhzcCjA7eTugR4vcp5dTFYoIQG0DaOKAkN/+gJTVjNDjpRR5
oGljZhKTeS4UNJTv/+ZjSMuAPycZq8LKRMOn/EgqT9MD4cIQ9VHN2qGc8jQt0Xrb
m58URvAoFesGnSjZcypk+JG2SbUfJ4WB3Db7+A+X7lu2219FIroFhNHMk9obYhXG
mkrhEnAsVsq/paPhCY4gdXWmSe7RNiAeSJeWhUSrNfjUACf1GF+l4CgBeBWIX+0=
=V40h
-----END PGP SIGNATURE-----
Merge tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix for the alignment of the event number reported at the
end of the 'DM_LIST_DEVICES' ioctl.
- a couple stable fixes for the DM crypt target.
- a DM raid health status reporting fix.
* tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: fix incorrect status output at the end of a "recover" process
dm crypt: reject sector_size feature if device length is not aligned to it
dm crypt: fix memory leak in crypt_ctr_cipher_old()
dm ioctl: fix alignment of event number in the device list
There are three important fields that indicate the overall health and
status of an array: dev_health, sync_ratio, and sync_action. They tell
us the condition of the devices in the array, and the degree to which
the array is synchronized.
This commit fixes a condition that is reported incorrectly. When a member
of the array is being rebuilt or a new device is added, the "recover"
process is used to synchronize it with the rest of the array. When the
process is complete, but the sync thread hasn't yet been reaped, it is
possible for the state of MD to be:
mddev->recovery = [ MD_RECOVERY_RUNNING MD_RECOVERY_RECOVER MD_RECOVERY_DONE ]
curr_resync_completed = <max dev size> (but not MaxSector)
and all rdevs to be In_sync.
This causes the 'array_in_sync' output parameter that is passed to
rs_get_progress() to be computed incorrectly and reported as 'false' --
or not in-sync. This in turn causes the dev_health status characters to
be reported as all 'a', rather than the proper 'A'.
This can cause erroneous output for several seconds at a time when tools
will want to be checking the condition due to events that are raised at
the end of a sync process. Fix this by properly calculating the
'array_in_sync' return parameter in rs_get_progress().
Also, remove an unnecessary intermediate 'recovery_cp' variable in
rs_get_progress().
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull HID subsystem fixes from Jiri Kosina:
- buffer management size fix for i2c-hid driver, from Adrian Salido
- tool ID regression fixes for Wacom driver from Jason Gerecke
- a few small assorted fixes and a few device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: multitouch: Support ALPS PTP stick with pid 0x120A"
HID: hidraw: fix power sequence when closing device
HID: wacom: Always increment hdev refcount within wacom_get_hdev_data
HID: wacom: generic: Clear ABS_MISC when tool leaves proximity
HID: wacom: generic: Send MSC_SERIAL and ABS_MISC when leaving prox
HID: i2c-hid: allocate hid buffers for real worst case
HID: rmi: Make sure the HID device is opened on resume
HID: multitouch: Support ALPS PTP stick with pid 0x120A
HID: multitouch: support buttons and trackpoint on Lenovo X1 Tab Gen2
HID: wacom: Correct coordinate system of touchring and pen twist
HID: wacom: Properly report negative values from Intuos Pro 2 Bluetooth
HID: multitouch: Fix system-control buttons not working
HID: add multi-input quirk for IDC6680 touchscreen
HID: wacom: leds: Don't try to control the EKR's read-only LEDs
HID: wacom: bits shifted too much for 9th and 10th buttons
Pull NVMe fixes from Christoph:
"A trivial one-liner from Martin to fix the visible of the uuid attr,
and another one (originally from Abhishek Shah, rewritten by me) to fix
the CMB addresses passed back to the controller in case of a system that
remaps BAR addresses between host and device."
Pull networking fixes from David Miller:
1) Check iwlwifi 9000 reorder buffer out-of-space condition properly,
from Sara Sharon.
2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov
Kasiviswanathan.
3) Fix session and tunnel release races in l2tp, from Guillaume Nault
and Sabrina Dubroca.
4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter.
5) Several mlx5 driver fixes from the Mellanox folks (max flow counters
cap check, invalid memory access in IPoIB support, etc.)
6) tun_get_user() should bail if skb->len is zero, from Alexander
Potapenko.
7) Fix RCU lookups in inetpeer, from Eric Dumazet.
8) Fix locking in packet_do_bund().
9) Handle cb->start() error properly in netlink dump code, from Jason
A. Donenfeld.
10) Handle multicast properly in UDP socket early demux code. From Paolo
Abeni.
11) Several erspan bug fixes in ip_gre, from Xin Long.
12) Fix use-after-free in socket filter code, in order to handle the
fact that listener lock is no longer taken during the three-way TCP
handshake. From Eric Dumazet.
13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov.
14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: 8021q: skip packets if the vlan is down
bpf: fix bpf_tail_call() x64 JIT
net: stmmac: dwmac-rk: Add RK3128 GMAC support
rndis_host: support Novatel Verizon USB730L
net: rtnetlink: fix info leak in RTM_GETSTATS call
socket, bpf: fix possible use after free
mlxsw: spectrum_router: Track RIF of IPIP next hops
mlxsw: spectrum_router: Move VRF refcounting
net: hns3: Fix an error handling path in 'hclge_rss_init_hw()'
net: mvpp2: Fix clock resource by adding an optional bus clock
r8152: add Linksys USB3GIGV1 id
l2tp: fix l2tp_eth module loading
ip_gre: erspan device should keep dst
ip_gre: set tunnel hlen properly in erspan_tunnel_init
ip_gre: check packet length and mtu correctly in erspan_xmit
ip_gre: get key from session_id correctly in erspan_rcv
tipc: use only positive error codes in messages
ppp: fix __percpu annotation
udp: perform source validation for mcast early demux
IPv4: early demux can return an error code
...
The structure stm32f7_setup is local to the source and does not need
to be in global scope, make it static const.
Cleans up sparse warning:
symbol 'stm32f7_setup' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure (of/i2c/platform)_device_id tables are NULL terminated.
Found by coccinelle spatch "misc/of_table.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add PCI ID for Intel Cedar Fork PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C drive setup structure is not properly allocated.
Make it static instead of pointer to store driver data.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
parse_cec_param() compares a string with "cec_disable" using only 7
characters of the 11-character-long string.
The proper solution for this would be:
#define CEC_DISABLE "cec_disable"
strncmp(str, CEC_DISABLE, strlen(CEC_DISABLE))
but when comparing a string against a string constant strncmp() has no
advantage over strcmp() because the comparison is guaranteed to be bound by
the string constant. So just replace str strncmp() with strcmp().
[ tglx: Made it use strcmp and updated the changelog ]
Fixes: 011d826111 ("RAS: Add a Corrected Errors Collector")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20170903075440.30250-1-nicolas.iooss_linux@m4x.org
Our first batch of fixes this release cycle, unfortunately a bit noisier
than usual. Two major groups stand out:
- Some pinctril dts/dtsi changes for stm32 due to a new driver being
merged during the merge window, and this aligns the DT contents between
the old format and the new. This could arguably be moved to the next
merge window but it also seemed relatively harmless to include now.
- Amlogic/meson had driver changes merged that required devicetree
changes to avoid functional/performance regressions. I've already
asked them to be more careful about this going forward, and making
sure drivers are compatible with older DTs when they make these kind
of changes. The platform is actively being upstreamed so there's a
few things in flight, we've seen this happen before and sometimes
it's hard to catch in time.
Besides that there is the usual mix of minor fixes.
-----BEGIN PGP SIGNATURE-----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=/0Nj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first batch of fixes this release cycle, unfortunately a bit
noisier than usual. Two major groups stand out:
- Some pinctril dts/dtsi changes for stm32 due to a new driver being
merged during the merge window, and this aligns the DT contents
between the old format and the new. This could arguably be moved to
the next merge window but it also seemed relatively harmless to
include now.
- Amlogic/meson had driver changes merged that required devicetree
changes to avoid functional/performance regressions. I've already
asked them to be more careful about this going forward, and making
sure drivers are compatible with older DTs when they make these
kind of changes. The platform is actively being upstreamed so
there's a few things in flight, we've seen this happen before and
sometimes it's hard to catch in time.
Besides that there is the usual mix of minor fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: dts: stm32: use right pinctrl compatible for stm32f469
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
ARM: defconfig: update Gemini defconfig
ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARM: dts: da850-evm: add serial and ethernet aliases
ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
ARM: dts: am33xx: Add spi alias to match SOC schematics
ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
arm64: dt marvell: Fix AP806 system controller size
MAINTAINERS: add Macchiatobin maintainers entry
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
ARM: at91: Replace uses of virt_to_phys with __pa_symbol
...
Update my imgtec.com and personal email address to my kernel.org one in
a few places as MIPS will soon no longer be part of Imagination
Technologies, and add mappings in .mailcap so get_maintainer.pl reports
the right address.
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to BSpec GLK like BXT needs to ignore the idle state of cores
before starting the DMC firmware's DC state handler.
Fixes: dbb28b5c3d ("drm/i915/DMC/GLK: Load DMC on GLK")
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003095159.711-2-imre.deak@intel.com
(cherry picked from commit b7208a3f3e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The DMC firmware program memory is lost after S3/S4 system suspend, so
we need to reprogram it during resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103070
Fixes: cebfcead63 ("drm/i915/DMC/CNL: Load DMC on CNL")
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003095159.711-1-imre.deak@intel.com
(cherry picked from commit 57522c4c87)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Port number 0 is an invalid port number. Set it to 1
as there is one port per i40iw device.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove duplicate set_64bit_val call to offset 24.
Replace some instances of set_64bit_val with
i40iw_insert_wqe_hdr as valid bit needs a write
barrier and should be the last write operation for the WQE.
Fixes: 786c6adb3a ("i40iw: add puda code")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Parse the vlan priority from the vlan tag and configure it to the
WC's sl field.
Fixes: abd49676c7 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Rename vlan_id field name to vlan as it contains more than the vlan_id.
Mask out non vlan id fields from vlan tag of the QED LL2 RX GSI
vlan output. As it is expected to be vlan id only.
Ignore vlan_id with value of zero.
Fixes: abd49676c7 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When UAR get_page fails, it needs to continue to cleanup debugfs for
congestion control parameters. Labels for error path were incorrectly
ordered.
This patch fixes to do correct cleanup on debugfs init failure and uar
get page failure.
Fixes: 4a2da0b8c0 ("IB/mlx5: Add debug control parameters for congestion control")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
commit f6810c15cf ("iommu/arm-smmu: Clean up early-probing
workarounds") removed kernel code that was allowing to initialize
and probe the SMMU devices early (ie earlier than PCI devices, through
linker script callback entries) in the boot process because it was not
needed any longer in that the SMMU devices/drivers now support deferred
probing.
Since the SMMUs probe routines are also in charge of requesting global
PCI ACS kernel enablement, commit f6810c15cf ("iommu/arm-smmu: Clean
up early-probing workarounds") also postponed PCI ACS enablement to
SMMUs devices probe time, which is too late given that PCI devices needs
to detect if PCI ACS is enabled to init the respective capability
through the following call path:
pci_device_add()
-> pci_init_capabilities()
-> pci_enable_acs()
Add code in the ACPI IORT SMMU platform devices initialization path
(that is called before ACPI PCI enumeration) to detect if there
exists firmware mappings to map root complexes ids to SMMU ids
and if so enable ACS for the system.
Fixes: f6810c15cf ("iommu/arm-smmu: Clean up early-probing workarounds")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 6edfa11cb3 ("clk: samsung: Add enable/disable operation for
PLL36XX clocks") added enable/disable operations to PLL clocks. Prior that
VPLL and EPPL clocks were always enabled because the enable bit was never
touched. Those clocks have to be enabled during suspend/resume cycle,
because otherwise board fails to enter sleep mode. This patch enables them
unconditionally before entering system suspend state. System restore
function will set them to the previous state saved in the register cache
done before that unconditional enable.
Fixes: 6edfa11cb3 ("clk: samsung: Add enable/disable operation for PLL36XX clocks")
CC: stable@vger.kernel.org # v4.13
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If a crypt mapping uses optional sector_size feature, additional
restrictions to mapped device segment size must be applied in
constructor, otherwise the device activation will fail later.
Fixes: 8f0009a225 ("dm crypt: optionally support larger encryption sector size")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The bit offset used to check if DCDC5 and DCDC6 are tied together in
poly-phase output is wrong. It was checking against a reserved bit,
which is always false.
In reality, neither the reference design layout nor actually produced
boards tie these two buck regulators together. But we should still
fix it, just in case.
Fixes: 1dbe0ccb06 ("regulator: axp20x-regulator: add support for AXP803")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, NVMe PCI host driver is programming CMB dma address as
I/O SQs addresses. This results in failures on systems where 1:1
outbound mapping is not used (example Broadcom iProc SOCs) because
CMB BAR will be progammed with PCI bus address but NVMe PCI EP will
try to access CMB using dma address.
To have CMB working on systems without 1:1 outbound mapping, we
program PCI bus address for I/O SQs instead of dma address. This
approach will work on systems with/without 1:1 outbound mapping.
Based on a report and previous patch from Abhishek Shah.
Fixes: 8ffaadf7 ("NVMe: Use CMB for the IO SQes if available")
Cc: stable@vger.kernel.org
Reported-by: Abhishek Shah <abhishek.shah@broadcom.com>
Tested-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
User-space normally keeps the node alive when creating a transaction
since it has a reference to the target. The local strong ref keeps it
alive if the sending process dies before the target process processes
the transaction. If the source process is malicious or has a reference
counting bug, this can fail.
In this case, when we attempt to decrement the node in the failure
path, the node has already been freed.
This is fixed by taking a tmpref on the node while constructing
the transaction. To avoid re-acquiring the node lock and inner
proc lock to increment the proc's tmpref, a helper is used that
does the ref increments on both the node and proc.
Signed-off-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
