commit 8cfd36a0b5 upstream.
When destroying a net namespace, all hwsim interfaces, which are not
created in default namespace are deleted. But the async deletion of the
interfaces could last longer than the actual destruction of the
namespace, which results to an use after free bug. Therefore use
synchronous deletion in this case.
Fixes: 100cb9ff40 ("mac80211_hwsim: Allow managing radios from non-initial namespaces")
Reported-by: syzbot+70ce058e01259de7bb1d@syzkaller.appspotmail.com
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95a2562590 ]
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69728051f5 ]
If a device is runtime PM suspended when we enter suspend and has
a dedicated wake IRQ, we can get the following warning:
WARNING: CPU: 0 PID: 108 at kernel/irq/manage.c:526 enable_irq+0x40/0x94
[ 102.087860] Unbalanced enable for IRQ 147
...
(enable_irq) from [<c06117a8>] (dev_pm_arm_wake_irq+0x4c/0x60)
(dev_pm_arm_wake_irq) from [<c0618360>]
(device_wakeup_arm_wake_irqs+0x58/0x9c)
(device_wakeup_arm_wake_irqs) from [<c0615948>]
(dpm_suspend_noirq+0x10/0x48)
(dpm_suspend_noirq) from [<c01ac7ac>]
(suspend_devices_and_enter+0x30c/0xf14)
(suspend_devices_and_enter) from [<c01adf20>]
(enter_state+0xad4/0xbd8)
(enter_state) from [<c01ad3ec>] (pm_suspend+0x38/0x98)
(pm_suspend) from [<c01ab3e8>] (state_store+0x68/0xc8)
This is because the dedicated wake IRQ for the device may have been
already enabled earlier by dev_pm_enable_wake_irq_check(). Fix the
issue by checking for runtime PM suspended status.
This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. On resume, dmesg will have the warning above.
The reason why I have not run into this issue earlier has been that I
typically run my PM test cases from on a serial console instead over ssh.
Fixes: c843455975 (PM / wakeirq: Enable dedicated wakeirq for suspend)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3cd091a773 ]
Commit 662591461c (ACPI / EC: Drop EC noirq hooks to fix a
regression) modified the ACPI EC driver so that it doesn't switch
over to busy polling mode during noirq stages of system suspend and
resume in an attempt to fix an issue resulting from that behavior.
However, that modification introduced a system resume regression on
Thinkpad X240, so make the EC driver switch over to the polling mode
during noirq stages of system suspend and resume again, which
effectively reverts the problematic commit.
Fixes: 662591461c (ACPI / EC: Drop EC noirq hooks to fix a regression)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197863
Reported-by: Markus Demleitner <m@tfiu.de>
Tested-by: Markus Demleitner <m@tfiu.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b84ca1875 ]
The interrupt status register in both dwmac1000 and dwmac4 ignores
interrupt enable (for dwmac4) / interrupt mask (for dwmac1000).
Therefore, if we want to check only the bits that can actually trigger
an irq, we have to filter the interrupt status register manually.
Commit 0a764db103 ("stmmac: Discard masked flags in interrupt status
register") fixed this for dwmac1000. Fix the same issue for dwmac4.
Just like commit 0a764db103 ("stmmac: Discard masked flags in
interrupt status register"), this makes sure that we do not get
spurious link up/link down prints.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 70f6bf2a3b ]
When maxcpus=1 is in the kernel command line, the BP is responsible
for re-enabling the HWP - because currently only the APs invoke
intel_pstate_hwp_enable() during their online process - which might
put the system into unstable state after resume.
Fix this by enabling the HWP explicitly on BP during resume.
Reported-by: Doug Smythies <dsmythies@telus.net>
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Yu Chen <yu.c.chen@intel.com>
[ rjw: Subject/changelog, minor modifications ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f4fc93d47 ]
I attach a back-end device to a cache set, and the cache set is not
registered yet, this back-end device did not attach successfully, and no
error returned:
[root]# echo 87859280-fec6-4bcc-20df7ca8f86b > /sys/block/sde/bcache/attach
[root]#
In sysfs_attach(), the return value "v" is initialized to "size" in
the beginning, and if no cache set exist in bch_cache_sets, the "v" value
would not change any more, and return to sysfs, sysfs regard it as success
since the "size" is a positive number.
This patch fixes this issue by assigning "v" with "-ENOENT" in the
initialization.
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73ac105be3 ]
back-end device sdm has already attached a cache_set with ID
f67ebe1f-f8bc-4d73-bfe5-9dc88607f119, then try to attach with
another cache set, and it returns with an error:
[root]# cd /sys/block/sdm/bcache
[root]# echo 5ccd0a63-148e-48b8-afa2-aca9cbd6279f > attach
-bash: echo: write error: Invalid argument
After that, execute a command to modify the label of bcache
device:
[root]# echo data_disk1 > label
Then we reboot the system, when the system power on, the back-end
device can not attach to cache_set, a messages show in the log:
Feb 5 12:05:52 ceph152 kernel: [922385.508498] bcache:
bch_cached_dev_attach() couldn't find uuid for sdm in set
In sysfs_attach(), dc->sb.set_uuid was assigned to the value
which input through sysfs, no matter whether it is success
or not in bch_cached_dev_attach(). For example, If the back-end
device has already attached to an cache set, bch_cached_dev_attach()
would fail, but dc->sb.set_uuid was changed. Then modify the
label of bcache device, it will call bch_write_bdev_super(),
which would write the dc->sb.set_uuid to the super block, so we
record a wrong cache set ID in the super block, after the system
reboot, the cache set couldn't find the uuid of the back-end
device, so the bcache device couldn't exist and use any more.
In this patch, we don't assigned cache set ID to dc->sb.set_uuid
in sysfs_attach() directly, but input it into bch_cached_dev_attach(),
and assigned dc->sb.set_uuid to the cache set ID after the back-end
device attached to the cache set successful.
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 682811b3ce ]
After long time running of random small IO writing,
I reboot the machine, and after the machine power on,
I found bcache got stuck, the stack is:
[root@ceph153 ~]# cat /proc/2510/task/*/stack
[<ffffffffa06b2455>] closure_sync+0x25/0x90 [bcache]
[<ffffffffa06b6be8>] bch_journal+0x118/0x2b0 [bcache]
[<ffffffffa06b6dc7>] bch_journal_meta+0x47/0x70 [bcache]
[<ffffffffa06be8f7>] bch_prio_write+0x237/0x340 [bcache]
[<ffffffffa06a8018>] bch_allocator_thread+0x3c8/0x3d0 [bcache]
[<ffffffff810a631f>] kthread+0xcf/0xe0
[<ffffffff8164c318>] ret_from_fork+0x58/0x90
[<ffffffffffffffff>] 0xffffffffffffffff
[root@ceph153 ~]# cat /proc/2038/task/*/stack
[<ffffffffa06b1abd>] __bch_btree_map_nodes+0x12d/0x150 [bcache]
[<ffffffffa06b1bd1>] bch_btree_insert+0xf1/0x170 [bcache]
[<ffffffffa06b637f>] bch_journal_replay+0x13f/0x230 [bcache]
[<ffffffffa06c75fe>] run_cache_set+0x79a/0x7c2 [bcache]
[<ffffffffa06c0cf8>] register_bcache+0xd48/0x1310 [bcache]
[<ffffffff812f702f>] kobj_attr_store+0xf/0x20
[<ffffffff8125b216>] sysfs_write_file+0xc6/0x140
[<ffffffff811dfbfd>] vfs_write+0xbd/0x1e0
[<ffffffff811e069f>] SyS_write+0x7f/0xe0
[<ffffffff8164c3c9>] system_call_fastpath+0x16/0x1
The stack shows the register thread and allocator thread
were getting stuck when registering cache device.
I reboot the machine several times, the issue always
exsit in this machine.
I debug the code, and found the call trace as bellow:
register_bcache()
==>run_cache_set()
==>bch_journal_replay()
==>bch_btree_insert()
==>__bch_btree_map_nodes()
==>btree_insert_fn()
==>btree_split() //node need split
==>btree_check_reserve()
In btree_check_reserve(), It will check if there is enough buckets
of RESERVE_BTREE type, since allocator thread did not work yet, so
no buckets of RESERVE_BTREE type allocated, so the register thread
waits on c->btree_cache_wait, and goes to sleep.
Then the allocator thread initialized, the call trace is bellow:
bch_allocator_thread()
==>bch_prio_write()
==>bch_journal_meta()
==>bch_journal()
==>journal_wait_for_write()
In journal_wait_for_write(), It will check if journal is full by
journal_full(), but the long time random small IO writing
causes the exhaustion of journal buckets(journal.blocks_free=0),
In order to release the journal buckets,
the allocator calls btree_flush_write() to flush keys to
btree nodes, and waits on c->journal.wait until btree nodes writing
over or there has already some journal buckets space, then the
allocator thread goes to sleep. but in btree_flush_write(), since
bch_journal_replay() is not finished, so no btree nodes have journal
(condition "if (btree_current_write(b)->journal)" never satisfied),
so we got no btree node to flush, no journal bucket released,
and allocator sleep all the times.
Through the above analysis, we can see that:
1) Register thread wait for allocator thread to allocate buckets of
RESERVE_BTREE type;
2) Alloctor thread wait for register thread to replay journal, so it
can flush btree nodes and get journal bucket.
then they are all got stuck by waiting for each other.
Hua Rui provided a patch for me, by allocating some buckets of
RESERVE_BTREE type in advance, so the register thread can get bucket
when btree node splitting and no need to waiting for the allocator
thread. I tested it, it has effect, and register thread run a step
forward, but finally are still got stuck, the reason is only 8 bucket
of RESERVE_BTREE type were allocated, and in bch_journal_replay(),
after 2 btree nodes splitting, only 4 bucket of RESERVE_BTREE type left,
then btree_check_reserve() is not satisfied anymore, so it goes to sleep
again, and in the same time, alloctor thread did not flush enough btree
nodes to release a journal bucket, so they all got stuck again.
So we need to allocate more buckets of RESERVE_BTREE type in advance,
but how much is enough? By experience and test, I think it should be
as much as journal buckets. Then I modify the code as this patch,
and test in the machine, and it works.
This patch modified base on Hua Rui’s patch, and allocate more buckets
of RESERVE_BTREE type in advance to avoid register thread and allocate
thread going to wait for each other.
[patch v2] ca->sb.njournal_buckets would be 0 in the first time after
cache creation, and no journal exists, so just 8 btree buckets is OK.
Signed-off-by: Hua Rui <huarui.dev@gmail.com>
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99361bbf26 ]
Kernel thread routine bch_writeback_thread() has the following code block,
447 down_write(&dc->writeback_lock);
448~450 if (check conditions) {
451 up_write(&dc->writeback_lock);
452 set_current_state(TASK_INTERRUPTIBLE);
453
454 if (kthread_should_stop())
455 return 0;
456
457 schedule();
458 continue;
459 }
If condition check is true, its task state is set to TASK_INTERRUPTIBLE
and call schedule() to wait for others to wake up it.
There are 2 issues in current code,
1, Task state is set to TASK_INTERRUPTIBLE after the condition checks, if
another process changes the condition and call wake_up_process(dc->
writeback_thread), then at line 452 task state is set back to
TASK_INTERRUPTIBLE, the writeback kernel thread will lose a chance to be
waken up.
2, At line 454 if kthread_should_stop() is true, writeback kernel thread
will return to kernel/kthread.c:kthread() with TASK_INTERRUPTIBLE and
call do_exit(). It is not good to enter do_exit() with task state
TASK_INTERRUPTIBLE, in following code path might_sleep() is called and a
warning message is reported by __might_sleep(): "WARNING: do not call
blocking ops when !TASK_RUNNING; state=1 set at [xxxx]".
For the first issue, task state should be set before condition checks.
Ineed because dc->writeback_lock is required when modifying all the
conditions, calling set_current_state() inside code block where dc->
writeback_lock is hold is safe. But this is quite implicit, so I still move
set_current_state() before all the condition checks.
For the second issue, frankley speaking it does not hurt when kernel thread
exits with TASK_INTERRUPTIBLE state, but this warning message scares users,
makes them feel there might be something risky with bcache and hurt their
data. Setting task state to TASK_RUNNING before returning fixes this
problem.
In alloc.c:allocator_wait(), there is also a similar issue, and is also
fixed in this patch.
Changelog:
v3: merge two similar fixes into one patch
v2: fix the race issue in v1 patch.
v1: initial buggy fix.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Cc: Michael Lyle <mlyle@lyle.org>
Cc: Junhui Tang <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a3381e3a65 ]
Commit b539cc82d4 (PM / Domains: Ignore domain-idle-states that are
not compatible), made it possible to ignore non-compatible
domain-idle-states OF nodes. However, in case that happens while doing
the OF parsing, the number of elements in the allocated array would
exceed the numbers actually needed, thus wasting memory.
Fix this by pre-iterating the genpd OF node and counting the number of
compatible domain-idle-states nodes, before doing the allocation. While
doing this, it makes sense to rework the code a bit to avoid open coding,
of parts responsible for the OF node iteration.
Let's also take the opportunity to clarify the function header for
of_genpd_parse_idle_states(), about what is being returned in case of
errors.
Fixes: b539cc82d4 (PM / Domains: Ignore domain-idle-states that are not compatible)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ac7292a25 ]
The page given to gnttab_end_foreign_access() to free could be a
compound page so use put_page() instead of free_page() since it can
handle both compound and single pages correctly.
This bug was discovered when migrating a Xen VM with several VIFs and
CONFIG_DEBUG_VM enabled. It hits a BUG usually after fewer than 10
iterations. All netfront devices disconnect from the backend during a
suspend/resume and this will call gnttab_end_foreign_access() if a
netfront queue has an outstanding skb. The mismatch between calling
get_page() and free_page() on a compound page causes a reference
counting error which is detected when DEBUG_VM is enabled.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f599c64fdf ]
When a netfront device is set up it registers a netdev fairly early on,
before it has set up the queues and is actually usable. A userspace tool
like NetworkManager will immediately try to open it and access its state
as soon as it appears. The bug can be reproduced by hotplugging VIFs
until the VM runs out of grant refs. It registers the netdev but fails
to set up any queues (since there are no more grant refs). In the
meantime, NetworkManager opens the device and the kernel crashes trying
to access the queues (of which there are none).
Fix this in two ways:
* For initial setup, register the netdev much later, after the queues
are setup. This avoids the race entirely.
* During a suspend/resume cycle, the frontend reconnects to the backend
and the queues are recreated. It is possible (though highly unlikely) to
race with something opening the device and accessing the queues after
they have been destroyed but before they have been recreated. Extend the
region covered by the rtnl semaphore to protect against this race. There
is a possibility that we fail to recreate the queues so check for this
in the open function.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63347db0af ]
The acpi_get_bus_status wrapper for acpi_bus_get_status_handle has some
code to handle certain device quirks, in some cases we also need this
quirk handling for the initial _STA call.
Specifically on some devices calling _STA before all _DEP dependencies
are met results in errors like these:
[ 0.123579] ACPI Error: No handler for Region [ECRM] (00000000ba9edc4c)
[GenericSerialBus] (20170831/evregion-166)
[ 0.123601] ACPI Error: Region GenericSerialBus (ID=9) has no handler
(20170831/exfldio-299)
[ 0.123618] ACPI Error: Method parse/execution failed
\_SB.I2C1.BAT1._STA, AE_NOT_EXIST (20170831/psparse-550)
acpi_get_bus_status already has code to avoid this, so by using it we
also silence these errors from the initial _STA call.
Note that in order for the acpi_get_bus_status handling for this to work,
we initialize dep_unmet to 1 until acpi_device_dep_initialize gets called,
this means that battery devices will be instantiated with an initial
status of 0. This is not a problem, acpi_bus_attach will get called soon
after the instantiation anyways and it will update the status as first
point of order.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54ddce7062 ]
The battery code uses acpi_device->dep_unmet to check for unmet deps and
if there are unmet deps it does not bind to the device to avoid errors
about missing OpRegions when calling ACPI methods on the device.
The missing OpRegions when there are unmet deps problem also applies to
the _STA method of some battery devices and calling it too early results
in errors like these:
[ 0.123579] ACPI Error: No handler for Region [ECRM] (00000000ba9edc4c)
[GenericSerialBus] (20170831/evregion-166)
[ 0.123601] ACPI Error: Region GenericSerialBus (ID=9) has no handler
(20170831/exfldio-299)
[ 0.123618] ACPI Error: Method parse/execution failed
\_SB.I2C1.BAT1._STA, AE_NOT_EXIST (20170831/psparse-550)
This commit fixes these errors happening when acpi_get_bus_status gets
called by checking dep_unmet for battery devices and reporting a status
of 0 until all dependencies are met.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a7770ae194 ]
The handling of empty DMI strings looks quite broken to me:
* Strings from 1 to 7 spaces are not considered empty.
* True empty DMI strings (string index set to 0) are not considered
empty, and result in allocating a 0-char string.
* Strings with invalid index also result in allocating a 0-char
string.
* Strings starting with 8 spaces are all considered empty, even if
non-space characters follow (sounds like a weird thing to do, but
I have actually seen occurrences of this in DMI tables before.)
* Strings which are considered empty are reported as 8 spaces,
instead of being actually empty.
Some of these issues are the result of an off-by-one error in memcmp,
the rest is incorrect by design.
So let's get it square: missing strings and strings made of only
spaces, regardless of their length, should be treated as empty and
no memory should be allocated for them. All other strings are
non-empty and should be allocated.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 79da472111 ("x86: fix DMI out of memory problems")
Cc: Parag Warudkar <parag.warudkar@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe9748b7b4 ]
Fixes failure to compile with recent envyas as a result of the 'movw'
alias being removed for v5.
A bit of history:
v3 only has a 16-bit sign-extended immediate mov op. In order to set
the high bits, there's a separate 'sethi' op. envyas validates that
the value passed to mov(imm) is between -0x8000 and 0x7fff. In order
to simplify macros that load both the low and high word, a 'movw'
alias was added which takes an unsigned 16-bit immediate. However the
actual hardware op still sign extends.
v5 has a full 32-bit immediate mov op. The v3 16-bit immediate mov op
is gone (loads 0 into the dst reg). However due to a bug in envyas,
the movw alias still existed, and selected the no-longer-present v3
16-bit immediate mov op. As a result usage of movw on v5 is the same
as mov with a 0x0 argument.
The proper fix throughout is to only ever use the 'movw' alias in
combination with 'sethi'. Anything else should get the sign-extended
validation to ensure that the intended value ends up in the
destination register.
Changes in fuc3 binaries is the result of a different encoding being
selected for a mov with an 8-bit value.
v2: added commit message written by Ilia, thanks for that!
v3: messed up rebasing, now it should apply
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1029361084 ]
On reboot SM can program port pkey table before ipoib registered its
event handler, which could result in missing pkey event and leave root
interface with initial pkey value from index 0.
Since OPA port starts with invalid pkey in index 0, root interface will
fail to initialize and stay down with no-carrier flag.
For IB ipoib interface may end up with pkey different from value
opensm put in pkey table idx 0, resulting in connectivity issues
(different mcast groups, for example).
Close the window by calling event handler after registration
to make sure ipoib pkey is in sync with port pkey table.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b1e7fe161 ]
The dd refcount is speculatively incremented prior to allocating
the fd memory with kzalloc(). If that kzalloc() failed the dd
refcount leaks.
Increment refcount on kzalloc success.
Fixes: e11ffbd575 ("IB/hfi1: Do not free hfi1 cdev parent structure early")
Reviewed-by: Michael J Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82a9792656 ]
The pci_request_irq() interfaces always adds the IRQF_SHARED bit to
all IRQ requests.
When the kernel is built with CONFIG_DEBUG_SHIRQ config flag, if the
IRQF_SHARED bit is set, a call to the IRQ handler is made from the
__free_irq() function. This is testing a race condition between the
IRQ cleanup and an IRQ racing the cleanup. The HFI driver should be
able to handle this race, but does not.
This race can cause traces that start with this footprint:
BUG: unable to handle kernel NULL pointer dereference at (null)
Call Trace:
<hfi1 irq handler>
...
__free_irq+0x1b3/0x2d0
free_irq+0x35/0x70
pci_free_irq+0x1c/0x30
clean_up_interrupts+0x53/0xf0 [hfi1]
hfi1_start_cleanup+0x122/0x190 [hfi1]
postinit_cleanup+0x1d/0x280 [hfi1]
remove_one+0x233/0x250 [hfi1]
pci_device_remove+0x39/0xc0
Export IRQ cleanup function so it can be called from other modules.
Using the exported cleanup function:
Re-order the driver cleanup code to clean up IRQ resources before
other resources, eliminating the race.
Re-order error path for init so that the race does not occur.
Reduce severity on spurious error message for SDMA IRQs to info.
Reviewed-by: Alex Estrin <alex.estrin@intel.com>
Reviewed-by: Patel Jay P <jay.p.patel@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 202a0a70e4 ]
When the frame check sequence (FCS) is split across the last two frames
of a fragmented packet, part of the FCS gets counted twice, once when
subtracting the FCS, and again when subtracting the previously received
data.
For example, if 1602 bytes are received, and the first fragment contains
the first 1600 bytes (including the first two bytes of the FCS), and the
second fragment contains the last two bytes of the FCS:
'skb->len == 1600' from the first fragment
size = lstatus & BD_LENGTH_MASK; # 1602
size -= ETH_FCS_LEN; # 1598
size -= skb->len; # -2
Since the size is unsigned, it wraps around and causes a BUG later in
the packet handling, as shown below:
kernel BUG at ./include/linux/skbuff.h:2068!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c021ec60] skb_pull+0x24/0x44
LR [c01e2fbc] gfar_clean_rx_ring+0x498/0x690
Call Trace:
[df7edeb0] [c01e2c1c] gfar_clean_rx_ring+0xf8/0x690 (unreliable)
[df7edf20] [c01e33a8] gfar_poll_rx_sq+0x3c/0x9c
[df7edf40] [c023352c] net_rx_action+0x21c/0x274
[df7edf90] [c0329000] __do_softirq+0xd8/0x240
[df7edff0] [c000c108] call_do_irq+0x24/0x3c
[c0597e90] [c00041dc] do_IRQ+0x64/0xc4
[c0597eb0] [c000d920] ret_from_except+0x0/0x18
--- interrupt: 501 at arch_cpu_idle+0x24/0x5c
Change the size to a signed integer and then trim off any part of the
FCS that was received prior to the last fragment.
Fixes: 6c389fc931 ("gianfar: fix size of scatter-gathered frames")
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbd27448fa ]
When using the max_mw_size parameter of ntb_transport to limit the size of
the Memory windows, communication cannot be established and the queues
freeze.
This is because the mw_size that's reported to the peer is correctly
limited but the size used locally is not. So the MW is initialized
with a buffer smaller than the window but the TX side is using the
full window. This means the TX side will be writing to a region of the
window that points nowhere.
This is easily fixed by applying the same limit to tx_size in
ntb_transport_init_queue().
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b081808a66 ]
Failure in XRCD FW deallocation command leaves memory leaked and
returns error to the user which he can't do anything about it.
This patch changes behavior to always free memory and always return
success to the user.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 40339af33c ]
In commit 36777d9fa2 ("i40e: check current configured input set when
adding ntuple filters") some code was added to report the input set
mask for a given filter when reporting it to the user.
This code is necessary so that the reported filter correctly displays
that it is or is not masking certain fields.
Unfortunately the code was incorrect. Development error accidentally
swapped the mask values for the IPv4 addresses with the L4 port numbers.
The port numbers are only 16bits wide while IPv4 addresses are 32 bits.
Unfortunately we assigned only 16 bits to the IPv4 address masks.
Additionally we assigned 32bit value 0xFFFFFFF to the TCP port numbers.
This second part does not matter as the value would be truncated to
16bits regardless, but it is unnecessary.
Fix the reported masks to properly report that the entire field is
masked.
Fixes: 36777d9fa2 ("i40e: check current configured input set when adding ntuple filters")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02b4016bfe ]
When implementing support for IP_USER_FLOW filters, we correctly
programmed a filter for both the non fragmented IPv4/Other filter, as
well as the fragmented IPv4 filters. However, we did not properly
program the input set for fragmented IPv4 PCTYPE. This meant that the
filters would almost certainly not match, unless the user specified all
of the flow types.
Add support to program the fragmented IPv4 filter input set. Since we
always program these filters together, we'll assume that the two input
sets must match, and will thus always program the input sets to the same
value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2bafa8fac1 ]
commit 2de6aa3a66 ("ixgbe: Add support for padding packet")
Uses RXDCTL.RLPML to limit the maximum frame size on Rx when using
build_skb. Unfortunately that register does not work on 82599.
Added an explicit check to avoid setting this register on 82599 MAC.
Extended the comment related to the setting of RXDCTL.RLPML to better
explain its purpose.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3624a8f025 ]
Returning EOPNOTSUPP is problematic because it can also be
returned by the method function, and we use it in quite a few
places in drivers these days.
Instead, dedicate EPROTONOSUPPORT to indicate that the ioctl framework
is enabled but the requested object and method are not supported by
the kernel. No other case will return this code, and it lets userspace
know to fall back to write().
grep says we do not use it today in drivers/infiniband subsystem.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 980b4c95e7 ]
Since CRYPTO_SHA384 does not exists, Kconfig should not select it.
Anyway, all SHA384 stuff is in CRYPTO_SHA512 which is already selected.
Fixes: a21eb94fc4d3i ("crypto: axis - add ARTPEC-6/7 crypto accelerator driver")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c7e1b40590 ]
Exar sleep wake-up handling has been done on a per-channel basis by
virtue of INT0 being accessible from each channel's address space. I
believe this was initially done out of necessity, but now that Exar
devices have their own driver, we can do things more efficiently by
registering a dedicated INT0 handler at the PCI device level.
I see this change providing the following benefits:
1. If more than one port is active, eliminates the redundant bus
cycles for reading INT0 on every interrupt.
2. This note associated with hooking in the per-channel handler in
8250_port.c is resolved:
/* Fixme: probably not the best place for this */
Cc: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cf315ea596 ]
When a VF is under PF VLAN assignment:
ip link set <pf> vf <#> vlan <vid>
This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":
failed to kill vid 0081/<vid> for device <vf>
This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.
Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.
The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.
However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a53285228 ]
Problem description:
After ethernet cable connect and disconnect for several iterations on a
device with i210, tx timestamp will stop being put into the socket.
Steps to reproduce:
1. Setup a device with i210 and wire it to a 802.1AS capable switch (
Extreme Networks Summit x440 is used in our case)
2. Have the gptp daemon running on the device and make sure it is synced
with the switch
3. Have the switch disable and enable the port, wait for the device gets
resynced with the switch
4. Iterates step 3 until the device is not albe to get resynced
5. Review the log in dmesg and you will see warning message "igb : clearing
Tx timestamp hang"
Root cause:
If ptp_tx_work() gets scheduled just before the port gets disabled, a LINK
DOWN event will be processed before ptp_tx_work(), which may cause timeout
in ptp_tx_work(). In the timeout logic, the TSYNCTXCTL's TXTT bit (Transmit
timestamp valid bit) is not cleared, causing no new timestamp loaded to
TXSTMP register. Consequently therefore, no new interrupt is triggerred by
TSICR.TXTS bit and no more Tx timestamp send to the socket.
Signed-off-by: Daniel Hua <daniel.hua@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 177132df5e ]
Before libvirt modifies the MAC address and vlan tag for an SRIOV VF
for use by a virtual machine (either using vfio device assignment or
macvtap passthru mode), it saves the current MAC address and vlan tag
so that it can reset them to their original value when the guest is
done. Libvirt can't leave the VF MAC set to the value used by the
now-defunct guest since it may be started again later using a
different VF, but it certainly shouldn't just pick any random value,
either. So it saves the state of everything prior to using the VF, and
resets it to that.
The igb driver initializes the MAC addresses of all VFs to
00:00:00:00:00:00, and reports that when asked (via an RTM_GETLINK
netlink message, also visible in the list of VFs in the output of "ip
link show"). But when libvirt attempts to restore the MAC address back
to 00:00:00:00:00:00 (using an RTM_SETLINK netlink message) the kernel
responds with "Invalid argument".
Forbidding a reset back to the original value leaves the VF MAC at the
value set for the now-defunct virtual machine. Especially on a system
with NetworkManager enabled, this has very bad consequences, since
NetworkManager forces all interfacess to be IFF_UP all the time - if
the same virtual machine is restarted using a different VF (or even on
a different host), there will be multiple interfaces watching for
traffic with the same MAC address.
To allow libvirt to revert to the original state, we need a way to
remove the administrative set MAC on a VF, to allow normal host
operation again, and to reset/overwrite the VF MAC via VF netdev.
This patch implements the outlined scenario by allowing to set the
VF MAC to 00:00:00:00:00:00 via RTM_SETLINK on the PF.
igb_ndo_set_vf_mac resets the IGB_VF_FLAG_PF_SET_MAC flag to 0,
so it's possible to reset the VF MAC back to the original value via
the VF netdev.
Note: Recent patches to libvirt allow for a workaround if the NIC
isn't capable of resetting the administrative MAC back to all 0, but
in theory the NIC should allow resetting the MAC in the first place.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <arron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 587d8628fb ]
This patch prevents the thinkpad_acpi driver from warning about 2 event
codes returned for keyboard palm-detection. No behavioral changes,
other than suppressing the warning in the kernel log. The events are
still forwarded via acpi-netlink channels.
We could, optionally, decide to forward the event through a
input-switch on the tpacpi input device. However, so far no suitable
input-code exists, and no similar drivers report such events. Hence,
leave it an acpi event for now.
Note that the event-codes are named based on empirical studies. On the
ThinkPad X1 5th Gen the sensor can be found underneath the arrow key.
Cc: Matthew Thode <mthode@mthode.org>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e0346f9fcb ]
If we receive the link status message from PF with link up before queues
are actually enabled, it will trigger a TX hang. This fixes the issue
by ignoring a link up message if the VF state is not yet in RUNNING
state.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 06aa040f03 ]
When a host disables and enables a PF device, all the associated
VFs are removed and added back in. It also generates a PFR which in turn
resets all the connected VFs. This behaviour is different from that of
Linux guest on Linux host. Hence we end up in a situation where there's
a PFR and device removal at the same time. And watchdog doesn't have a
clue about this and schedules a reset_task. This patch adds code to send
signal to reset_task that the device is currently being removed.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e58decc9c5 ]
Fix to return error code -EINVAL instead of 0 when num_vfs above
limit_vfs, as done elsewhere in this function.
Fixes: 0dc7862191 ("nfp: handle SR-IOV already enabled when driver is probing")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7ad81482ca ]
We get the "new_profile_index" value from the mouse device when we're
handling raw events. Smatch taints it as untrusted data and complains
that we need a bounds check. This seems like a reasonable warning
otherwise there is a small read beyond the end of the array.
Fixes: 0e70f97f25 ("HID: roccat: Add support for Kova[+] mouse")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cba04cdf43 ]
The interrupt is requested before the device is powered on and
it's value in some cases cannot be reliable. It happens on some
devices that an interrupt is generated as soon as requested
before having the chance to disable the irq.
Set the irq flag as IRQ_NOAUTOEN before requesting it.
This patch mutes the error:
stmfts 2-0049: failed to read events: -11
received sometimes during boot time.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 96d5eaa9bb ]
While testing with the ARM specific memset() macro removed, I ran into a
compiler warning that shows an old bug:
drivers/scsi/arm/fas216.c: In function 'fas216_rq_sns_done':
drivers/scsi/arm/fas216.c:2014:40: error: argument to 'sizeof' in 'memset' call is the same expression as the destination; did you mean to provide an explicit length? [-Werror=sizeof-pointer-memaccess]
It turns out that the definition of the scsi_cmd structure changed back
in linux-2.6.25, so now we clear only four bytes (sizeof(pointer))
instead of 96 (SCSI_SENSE_BUFFERSIZE). I did not check whether we
actually need to initialize the buffer here, but it's clear that if we
do it, we should use the correct size.
Fixes: de25deb180 ("[SCSI] use dynamically allocated sense buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00db63c128 ]
If valid netdevice is not found for RoCE, GID table should not be
searched with NULL netdevice.
Doing so causes the search routines to ignore the netdev argument and may
match the wrong GID table entry if the netdev is deleted.
Fixes: abae1b71dd ("IB/cma: cma_validate_port should verify the port and netdevice")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ddcff49b6 ]
'hwname' is malloced in hwsim_new_radio_nl() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ff4dd73dd2 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f541c09ebf ]
According to all published information, the watchdog disable bit for SB800
compatible controllers is bit 1 of PM register 0x48, not bit 2. For the
most part that doesn't matter in practice, since the bit has to be cleared
to enable watchdog address decoding, which is the default setting, but it
still needs to be fixed.
Cc: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 246d8b184c ]
polling the completion queue directly does not interfere
with the existing polling logic, hence drop the requirement.
Be aware that running ib_process_cq_direct with non IB_POLL_DIRECT
CQ may trigger concurrent CQ processing.
This can be used for polling mode ULPs.
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Reported-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
[maxg: added wcs array argument to __ib_process_cq]
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44a5f423e7 ]
When performing a read using FIFO mode, the spi controller shifts out
the last 2 bytes that were written in a previous transfer on MOSI.
This undocumented behaviour can cause devices to misinterpret the
transfer, so we explicitly clear the WFIFO before each read.
This behaviour was noticed on EspressoBin.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
