commit 94e46a4f2d upstream.
This fixes an oops on unbind / module unload (on the musb omap2430
platform).
musb_remove function now calls musb_platform_exit before disabling
runtime pm.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df6b074dbe upstream.
Without pm_runtime_{get,put}_sync calls in place, reading
vbus status via /sys causes the following error:
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
pgd = b333e822
[fa0ab060] *pgd=48011452(bad)
[<c05261b0>] (musb_default_readb) from [<c0525bd0>] (musb_vbus_show+0x58/0xe4)
[<c0525bd0>] (musb_vbus_show) from [<c04c0148>] (dev_attr_show+0x20/0x44)
[<c04c0148>] (dev_attr_show) from [<c0259f74>] (sysfs_kf_seq_show+0x80/0xdc)
[<c0259f74>] (sysfs_kf_seq_show) from [<c0210bac>] (seq_read+0x250/0x448)
[<c0210bac>] (seq_read) from [<c01edb40>] (__vfs_read+0x1c/0x118)
[<c01edb40>] (__vfs_read) from [<c01edccc>] (vfs_read+0x90/0x144)
[<c01edccc>] (vfs_read) from [<c01ee1d0>] (SyS_read+0x3c/0x74)
[<c01ee1d0>] (SyS_read) from [<c0106fe0>] (ret_fast_syscall+0x0/0x54)
Solution was suggested by Tony Lindgren <tony@atomide.com>.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17539f2f4f upstream.
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87c ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c91815b596 upstream.
This is a requirement which has always existed but, somehow, wasn't
reflected in the documentation and problems weren't found until now
when Tuba Yavuz found a possible deadlock happening between dwc3 and
f_hid. She described the situation as follows:
spin_lock_irqsave(&hidg->write_spinlock, flags); // first acquire
/* we our function has been disabled by host */
if (!hidg->req) {
free_ep_req(hidg->in_ep, hidg->req);
goto try_again;
}
[...]
status = usb_ep_queue(hidg->in_ep, hidg->req, GFP_ATOMIC);
=>
[...]
=> usb_gadget_giveback_request
=>
f_hidg_req_complete
=>
spin_lock_irqsave(&hidg->write_spinlock, flags); // second acquire
Note that this happens because dwc3 would call ->complete() on a
failed usb_ep_queue() due to failed Start Transfer command. This is,
anyway, a theoretical situation because dwc3 currently uses "No
Response Update Transfer" command for Bulk and Interrupt endpoints.
It's still good to make this case impossible to happen even if the "No
Reponse Update Transfer" command is changed.
Reported-by: Tuba Yavuz <tuba@ece.ufl.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit daaecc6541 upstream.
We don't support PRTCAP == OTG yet, so prevent user from
setting it via debugfs.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64627388b5 upstream.
USB3 hubs don't support global suspend.
USB3 specification 10.10, Enhanced SuperSpeed hubs only support selective
suspend and resume, they do not support global suspend/resume where the
hub downstream facing ports states are not affected.
When system enters hibernation it first enters freeze process where only
the root hub enters suspend, usb_port_suspend() is not called for other
devices, and suspend status flags are not set for them. Other devices are
expected to suspend globally. Some external USB3 hubs will suspend the
downstream facing port at global suspend. These devices won't be resumed
at thaw as the suspend status flag is not set.
A USB3 removable hard disk connected through a USB3 hub that won't resume
at thaw will fail to synchronize SCSI cache, return “cmd cmplt err -71”
error, and needs a 60 seconds timeout which causing system hang for 60s
before the USB host reset the port for the USB3 removable hard disk to
recover.
Fix this by always calling usb_port_suspend() during freeze for USB3
devices.
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fafcfdf63 upstream.
It looks like there is a possibility of a double-free vulnerability on an
error path of the f_midi_set_alt function in the f_midi driver. If the
path is feasible then free_ep_req gets called twice:
req->complete = f_midi_complete;
err = usb_ep_queue(midi->out_ep, req, GFP_ATOMIC);
=> ...
usb_gadget_giveback_request
=>
f_midi_complete (CALLBACK)
(inside f_midi_complete, for various cases of status)
free_ep_req(ep, req); // first kfree
if (err) {
ERROR(midi, "%s: couldn't enqueue request: %d\n",
midi->out_ep->name, err);
free_ep_req(midi->out_ep, req); // second kfree
return err;
}
The double-free possibility was introduced with commit ad0d1a058e
("usb: gadget: f_midi: fix leak on failed to enqueue out requests").
Found by MOXCAFE tool.
Signed-off-by: Tuba Yavuz <tuba@ece.ufl.edu>
Fixes: ad0d1a058e ("usb: gadget: f_midi: fix leak on failed to enqueue out requests")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaa358c779 upstream.
Mention that ->complete() should never be called from within
usb_ep_queue().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af6f852909 upstream.
musb->endpoints[] has array size MUSB_C_NUM_EPS.
We must check array bounds before accessing the array and not afterwards.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6555ad13a0 upstream.
Add device id for Harman FirmwareHubEmulator to make the device
auto-detectable by the driver.
Signed-off-by: Clemens Werther <clemens.werther@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9608e5c0f0 upstream.
This patch adds a device ID for the RT Systems cable used to
program Yaesu VX-8R/VX-8DR handheld radios. It uses the main
FTDI VID instead of the common RT Systems VID.
Signed-off-by: Major Hayden <major@mhtx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2471d4a24 upstream.
In the earlier commit dad3f793f2 ("usb: dwc2: Make sure we
disconnect the gadget state"), I was trying to fix up the
fact that we somehow weren't disconnecting the gadget state,
so that when the OTG port was plugged in the second time we
would get warnings about the state tracking being wrong.
(This seems to be due to a quirk of the HiKey board where
we do not ever get any otg interrupts, particularly the session
end detected signal. Instead we only see status change
interrupt.)
The fix there was somewhat simple, as it just made sure to
call dwc2_hsotg_disconnect() before we connected things up
in OTG mode, ensuring the state handling didn't throw errors.
But in looking at a different issue I was seeing with UDC
state handling, I realized that it would be much better
to call dwc2_hsotg_disconnect when we get the state change
signal moving to host mode.
Thus, this patch removes the earlier disconnect call I added
and moves it (and the needed locking) to the host mode
transition.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd3f1790b0 upstream.
xhci_disable_slot() allows the invoker to pass a command pointer
as paramenter. Otherwise, it will allocate one. This will cause
memory leak when a command structure was allocated inside of this
function while queuing command trb fails. Another problem comes up
when the invoker passed a command pointer, but xhci_disable_slot()
frees it when it detects a dead host.
This patch fixes these two problems by removing the command parameter
from xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b64149ca01 upstream.
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it checks
the corespoding virt-dev pointer and returns directly (w/o issuing
disable slot command) if it's null.
This is unnecessary and will cause problems in case where virt-dev
allocation fails and xhci_disable_slot() is called to roll back the
hardware state. Refer to the implementation of xhci_alloc_dev().
This patch removes lines to check virt-dev in xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b16ea8b949 upstream.
The FIFO/Queue type values are incorrect. Correct them according to
DWC_usb3 programming guide section 1.2.27 (or DWC_usb31 section 1.2.25).
Additionally, this patch includes ProtocolStatusQ and AuxEventQ types.
Fixes: cf6d867d3b ("usb: dwc3: core: add fifo space helper")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03310a1548 ]
This code looks up a USB device node from a given parent USB device but
never dropped its reference to the returned node.
As only the address of the node is used for a later matching, the
reference can be dropped immediately.
Note that this trigger implementation confuses the description of the
USB device connected to a port with the port itself (which does not have
a device-tree representation).
Fixes: 4f04c210d0 ("usb: core: read USB ports from DT in the usbport LED trigger driver")
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 084a804e01 upstream.
To reproduce the lock up do the following
- connect otg host adapter and a USB device to the dual-role port
so that it is in host mode.
- suspend to mem.
- disconnect otg adapter.
- resume the system.
If we call dwc3_host_exit() before tasks are thawed
xhci_plat_remove() seems to lock up at the second usb_remove_hcd() call.
To work around this we queue the _dwc3_set_mode() work on
the system_freezable_wq.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Suggested-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a087f0321 upstream.
When I debug a kernel crash issue in funcitonfs, found ffs_data.ref
overflowed, While functionfs is unmounting, ffs_data is put twice.
Commit 43938613c6 ("drivers, usb: convert ffs_data.ref from atomic_t to
refcount_t") can avoid refcount overflow, but that is risk some situations.
So no need put ffs data in ffs_fs_kill_sb, already put in ffs_data_closed.
The issue can be reproduced in Mediatek mt6763 SoC, ffs for ADB device.
KASAN enabled configuration reports use-after-free errro.
BUG: KASAN: use-after-free in refcount_dec_and_test+0x14/0xe0 at addr ffffffc0579386a0
Read of size 4 by task umount/4650
====================================================
BUG kmalloc-512 (Tainted: P W O ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in ffs_fs_mount+0x194/0x844 age=22856 cpu=2 pid=566
alloc_debug_processing+0x1ac/0x1e8
___slab_alloc.constprop.63+0x640/0x648
__slab_alloc.isra.57.constprop.62+0x24/0x34
kmem_cache_alloc_trace+0x1a8/0x2bc
ffs_fs_mount+0x194/0x844
mount_fs+0x6c/0x1d0
vfs_kern_mount+0x50/0x1b4
do_mount+0x258/0x1034
INFO: Freed in ffs_data_put+0x25c/0x320 age=0 cpu=3 pid=4650
free_debug_processing+0x22c/0x434
__slab_free+0x2d8/0x3a0
kfree+0x254/0x264
ffs_data_put+0x25c/0x320
ffs_data_closed+0x124/0x15c
ffs_fs_kill_sb+0xb8/0x110
deactivate_locked_super+0x6c/0x98
deactivate_super+0xb0/0xbc
INFO: Object 0xffffffc057938600 @offset=1536 fp=0x (null)
......
Call trace:
[<ffffff900808cf5c>] dump_backtrace+0x0/0x250
[<ffffff900808d3a0>] show_stack+0x14/0x1c
[<ffffff90084a8c04>] dump_stack+0xa0/0xc8
[<ffffff900826c2b4>] print_trailer+0x158/0x260
[<ffffff900826d9d8>] object_err+0x3c/0x40
[<ffffff90082745f0>] kasan_report_error+0x2a8/0x754
[<ffffff9008274f84>] kasan_report+0x5c/0x60
[<ffffff9008273208>] __asan_load4+0x70/0x88
[<ffffff90084cd81c>] refcount_dec_and_test+0x14/0xe0
[<ffffff9008d98f9c>] ffs_data_put+0x80/0x320
[<ffffff9008d9d904>] ffs_fs_kill_sb+0xc8/0x110
[<ffffff90082852a0>] deactivate_locked_super+0x6c/0x98
[<ffffff900828537c>] deactivate_super+0xb0/0xbc
[<ffffff90082af0c0>] cleanup_mnt+0x64/0xec
[<ffffff90082af1b0>] __cleanup_mnt+0x10/0x18
[<ffffff90080d9e68>] task_work_run+0xcc/0x124
[<ffffff900808c8c0>] do_notify_resume+0x60/0x70
[<ffffff90080866e4>] work_pending+0x10/0x14
Cc: stable@vger.kernel.org
Signed-off-by: Xinyong <xinyong.fang@linux.alibaba.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5f596830e upstream.
This change fixes buffer overflows and silent data corruption with the
usbmon device driver text file read operations.
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb88a05887 upstream.
Corsair Strafe RGB keyboard does not respond to usb control messages
sometimes and hence generates timeouts.
Commit de3af5bf25 ("usb: quirks: add delay init quirk for Corsair
Strafe RGB keyboard") tried to fix those timeouts by adding
USB_QUIRK_DELAY_INIT.
Unfortunately, even with this quirk timeouts of usb_control_msg()
can still be seen, but with a lower frequency (approx. 1 out of 15):
[ 29.103520] usb 1-8: string descriptor 0 read error: -110
[ 34.363097] usb 1-8: can't set config #1, error -110
Adding further delays to different locations where usb control
messages are issued just moves the timeouts to other locations,
e.g.:
[ 35.400533] usbhid 1-8:1.0: can't add hid device: -110
[ 35.401014] usbhid: probe of 1-8:1.0 failed with error -110
The only way to reliably avoid those issues is having a pause after
each usb control message. In approx. 200 boot cycles no more timeouts
were seen.
Addionaly, keep USB_QUIRK_DELAY_INIT as it turned out to be necessary
to have the delay in hub_port_connect() after hub_port_init().
The overall boot time seems not to be influenced by these additional
delays, even on fast machines and lightweight distributions.
Fixes: de3af5bf25 ("usb: quirks: add delay init quirk for Corsair Strafe RGB keyboard")
Cc: stable@vger.kernel.org
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df3334c223 upstream.
Currently the driver attempts to spin lock on udc->lock before a NULL
pointer check is performed on udc, hence there is a potential null
pointer dereference on udc->lock. Fix this by moving the null check
on udc before the lock occurs.
Fixes: ea6873a45a ("usbip: vudc: Add SysFS infrastructure for VUDC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5126a504b6 upstream.
This USB-SATA controller seems to be similar with JMicron bridge
152d:2566 already on the list. Adding it here fixes "Invalid
field in cdb" errors.
Signed-off-by: Teijo Kinnunen <teijo.kinnunen@code-q.fi>
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a513c905b upstream.
A typo broke the comparison.
Fixes: cbeef22fd6 ("usb: uas: unconditionally bring back host after reset")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@kernel.org
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 191edc5e2e upstream.
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17aa31f13c upstream.
This fixes an issue that a gadget driver (usb_f_fs) is possible to
stop rx transactions after the usb-dmac is used because the following
functions missed to set/check the "running" flag.
- usbhsf_dma_prepare_pop_with_usb_dmac()
- usbhsf_dma_pop_done_with_usb_dmac()
So, if next transaction uses pio, the usbhsf_prepare_pop() can not
start the transaction because the "running" flag is 0.
Fixes: 8355b2b308 ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 675272d092 upstream.
In commit 2bfa0719ac ("usb: gadget: function: f_fs: pass
companion descriptor along") there is a pointer arithmetic
bug where the comp_desc is obtained as follows:
comp_desc = (struct usb_ss_ep_comp_descriptor *)(ds +
USB_DT_ENDPOINT_SIZE);
Since ds is a pointer to usb_endpoint_descriptor, adding
7 to it ends up going out of bounds (7 * sizeof(struct
usb_endpoint_descriptor), which is actually 7*9 bytes) past
the SS descriptor. As a result the maxburst value will be
read incorrectly, and the UDC driver will also get a garbage
comp_desc (assuming it uses it).
Since Felipe wrote, "Eventually, f_fs.c should be converted
to use config_ep_by_speed() like all other functions, though",
let's finally do it. This allows the other usb_ep fields to
be properly populated, such as maxpacket and mult. It also
eliminates the awkward speed-based descriptor lookup since
config_ep_by_speed() does that already using the ones found
in struct usb_function.
Fixes: 2bfa0719ac ("usb: gadget: function: f_fs: pass companion descriptor along")
Cc: stable@vger.kernel.org
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cf439e0d3 upstream.
During _ffs_func_bind(), the received descriptors are evaluated
to prepare for binding with the gadget in order to allocate
endpoints and optionally set up OS descriptors. However, the
high- and super-speed descriptors are only parsed based on
whether the gadget_is_dualspeed() and gadget_is_superspeed()
calls are true, respectively.
This is a problem in case a userspace program always provides
all of the {full,high,super,OS} descriptors when configuring a
function. Then, for example if a gadget device is not capable
of SuperSpeed, the call to ffs_do_descs() for the SS descriptors
is skipped, resulting in an incorrect offset calculation for
the vla_ptr when moving on to the OS descriptors that follow.
This causes ffs_do_os_descs() to fail as it is now looking at
the SS descriptors' offset within the raw_descs buffer instead.
_ffs_func_bind() should evaluate the descriptors unconditionally,
so remove the checks for gadget speed.
Fixes: f0175ab519 ("usb: gadget: f_fs: OS descriptors support")
Cc: stable@vger.kernel.org
Co-Developed-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52ad2bd891 upstream.
This patch adds support for new CASSY devices to the ldusb driver. The
PIDs are also added to the ignore list in hid-quirks.
Signed-off-by: Karsten Koop <kkoop@ld-didactic.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f035d139ff upstream.
DWC3 tracks TRB counter for each ep0 direction separately. In control
read transfer completion handler, the driver needs to reset the TRB
enqueue counter for ep0 IN direction. Currently the driver only resets
the TRB counter for control OUT endpoint. Check for the data direction
and properly reset the TRB counter from correct control endpoint.
Cc: stable@vger.kernel.org
Fixes: c2da2ff006 ("usb: dwc3: ep0: don't use ep0in for transfers")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6180026341 upstream.
There are 2 control endpoint structures for DWC3. However, the driver
only updates the OUT direction control endpoint structure during
ConnectDone event. DWC3 driver needs to update the endpoint max packet
size for control IN endpoint as well. If the max packet size is not
properly set, then the driver will incorrectly calculate the data
transfer size and fail to send ZLP for HS/FS 3-stage control read
transfer.
The fix is simply to update the max packet size for the ep0 IN direction
during ConnectDone event.
Cc: stable@vger.kernel.org
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02a10f061a upstream.
commit a8c06e407e ("usb: separate out sysdev pointer from usb_bus")
converted to use hcd->self.sysdev for DMA operations instead of
hcd->self.controller, but forgot to do it for hcd test mode. Replace
the correct one in this commit.
Fixes: a8c06e407e ("usb: separate out sysdev pointer from usb_bus")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a1646d922 upstream.
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Device ids found here:
usb 3-3: New USB device found, idVendor=1b1c, idProduct=1b13
usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3: Product: Corsair K70 RGB Gaming Keyboard
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46408ea558 upstream.
There is a race condition between finish_unlinks->finish_urb() function
and usb_kill_urb() in ohci controller case. The finish_urb calls
spin_unlock(&ohci->lock) before usb_hcd_giveback_urb() function call,
then if during this time, usb_kill_urb is called for another endpoint,
then new ed will be added to ed_rm_list at beginning for unlink, and
ed_rm_list will point to newly added.
When finish_urb() is completed in finish_unlinks() and ed->td_list
becomes empty as in below code (in finish_unlinks() function):
if (list_empty(&ed->td_list)) {
*last = ed->ed_next;
ed->ed_next = NULL;
} else if (ohci->rh_state == OHCI_RH_RUNNING) {
*last = ed->ed_next;
ed->ed_next = NULL;
ed_schedule(ohci, ed);
}
The *last = ed->ed_next will make ed_rm_list to point to ed->ed_next
and previously added ed by usb_kill_urb will be left unreferenced by
ed_rm_list. This causes usb_kill_urb() hang forever waiting for
finish_unlink to remove added ed from ed_rm_list.
The main reason for hang in this race condtion is addition and removal
of ed from ed_rm_list in the beginning during usb_kill_urb and later
last* is modified in finish_unlinks().
As suggested by Alan Stern, the solution for proper handling of
ohci->ed_rm_list is to remove ed from the ed_rm_list before finishing
any URBs. Then at the end, we can add ed back to the list if necessary.
This properly handle the updated ohci->ed_rm_list in usb_kill_urb().
Fixes: 977dcfdc60 ("USB: OHCI: don't lose track of EDs when a controller dies")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Aman Deep <aman.deep@samsung.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2685bdacd upstream.
Running io_watchdog_func() while ohci_urb_enqueue() is running can
cause a race condition where ohci->prev_frame_no is corrupted and the
watchdog can mis-detect following error:
ohci-platform 664a0800.usb: frame counter not updating; disabled
ohci-platform 664a0800.usb: HC died; cleaning up
Specifically, following scenario causes a race condition:
1. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
2. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
3. ohci_urb_enqueue() sets ohci->prev_frame_no to a frame number
read by ohci_frame_no(ohci)
4. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
5. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section
6. Later, ohci_urb_enqueue() is called
7. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
8. The timer scheduled on step 4 expires and io_watchdog_func() runs
9. io_watchdog_func() calls spin_lock_irqsave(&ohci->lock, flags)
and waits on it because ohci_urb_enqueue() is already in the
critical section on step 7
10. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
11. ohci_urb_enqueue() sets ohci->prev_frame_no to new frame number
read by ohci_frame_no(ohci) because the frame number proceeded
between step 3 and 6
12. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
13. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section, then wake up
io_watchdog_func() which is waiting on step 9
14. io_watchdog_func() enters the critical section
15. io_watchdog_func() calls ohci_frame_no(ohci) and set frame_no
variable to the frame number
16. io_watchdog_func() compares frame_no and ohci->prev_frame_no
On step 16, because this calling of io_watchdog_func() is scheduled on
step 4, the frame number set in ohci->prev_frame_no is expected to the
number set on step 3. However, ohci->prev_frame_no is overwritten on
step 11. Because step 16 is executed soon after step 11, the frame
number might not proceed, so ohci->prev_frame_no must equals to
frame_no.
To address above scenario, this patch introduces a special sentinel
value IO_WATCHDOG_OFF and set this value to ohci->prev_frame_no when
the watchdog is not pending or running. When ohci_urb_enqueue()
schedules the watchdog (step 4 and 12 above), it compares
ohci->prev_frame_no to IO_WATCHDOG_OFF so that ohci->prev_frame_no is
not overwritten while io_watchdog_func() is running.
Signed-off-by: Shigeru Yoshida <Shigeru.Yoshida@windriver.com>
Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ded600ea9f ]
If of_clk_get() fails, the clean-up of already initialized clocks should be
the same as when clk_prepare_enable() fails. Thus a clk_disable_unprepare()
for each clock should be called before the clk_put().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 16adc674d0 ("usb: dwc3: ep0: fix setup_packet_pending initialization")
Signed-off-by: Andreas Platschek <andreas.platschek@opentech.at>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 009f41aed4 upstream.
Keep usbip_device sockfd state in sync with tcp_socket. When tcp_socket
is reset to null, reset sockfd to -1 to keep it in sync.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e901b98738 upstream.
This patch adds a new helper function to perform a sanity check of the
given URB to see whether it contains a valid endpoint. It's a light-
weight version of what usb_submit_urb() does, but without the kernel
warning followed by the stack trace, just returns an error code.
Especially for a driver that doesn't parse the descriptor but fills
the URB with the fixed endpoint (e.g. some quirks for non-compliant
devices), this kind of check is preferable at the probe phase before
actually submitting the urb.
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec897569ad upstream.
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit
2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Fixes: 2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/18559/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11fb379987 upstream.
The current code tries to test for bits that are masked out by
usb_endpoint_maxp(). Instead, use the proper accessor to access
the new high bandwidth bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbeef22fd6 upstream.
Quoting Hans:
If we return 1 from our post_reset handler, then our disconnect handler
will be called immediately afterwards. Since pre_reset blocks all scsi
requests our disconnect handler will then hang in the scsi_remove_host
call.
This is esp. bad because our disconnect handler hanging for ever also
stops the USB subsys from enumerating any new USB devices, causes commands
like lsusb to hang, etc.
In practice this happens when unplugging some uas devices because the hub
code may see the device as needing a warm-reset and calls usb_reset_device
before seeing the disconnect. In this case uas_configure_endpoints fails
with -ENODEV. We do not want to print an error for this, so this commit
also silences the shost_printk for -ENODEV.
ENDQUOTE
However, if we do that we better drop any unconditional execution
and report to the SCSI subsystem that we have undergone a reset
but we are not operational now.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce5bf9a50d upstream.
Upon usb composition switch there is possibility of ep0 file
release happening after gadget driver bind. In case of composition
switch from adb to a non-adb composition gadget will never gets
bound again resulting into failure of usb device enumeration. Fix
this issue by checking FFS_FL_BOUND flag and avoid extra
gadget driver unbind if it is already done as part of composition
switch.
This fixes adb reconnection error reported on Android running
v4.4 and above kernel versions. Verified on Hikey running vanilla
v4.15-rc7 + few out of tree Mali patches.
Reviewed-at: https://android-review.googlesource.com/#/c/582632/
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg KH <gregkh@linux-foundation.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Cc: Badhri <badhri@google.com>
Cc: Android Kernel Team <kernel-team@android.com>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
[AmitP: Cherry-picked it from android-4.14 and updated the commit log]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7b8f77872 upstream.
According to drivers/usb/serial/io_edgeport.c, the driver may sleep
under a spinlock.
The function call path is:
edge_bulk_in_callback (acquire the spinlock)
process_rcvd_data
process_rcvd_status
change_port_settings
send_iosp_ext_cmd
write_cmd_usb
usb_kill_urb --> may sleep
To fix it, the redundant usb_kill_urb() is removed from the error path
after usb_submit_urb() fails.
This possible bug is found by my static analysis tool (DSAC) and checked
by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
