Commit graph

287,481 commits

Author SHA1 Message Date
Yijing Wang
017ffe64e8 PCI: Hold pci_slot_mutex while searching bus->slots list
Previously, pci_setup_device() and similar functions searched the
pci_bus->slots list without any locking.  It was possible for another
thread to update the list while we searched it.

Add pci_dev_assign_slot() to search the list while holding pci_slot_mutex.

[bhelgaas: changelog, fold in CONFIG_SYSFS fix]
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-07-30 16:19:53 -05:00
Vladimir Zapolskiy
2f51a9b8ad net: phy: spi_ks8995: clean up ks8995_registers_read/write
The change removes redundant sysfs binary file boundary checks,
since this task is already done on caller side in fs/sysfs/file.c

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 14:16:45 -07:00
hayeswang
37608f3e57 r8152: reset device when tx timeout
The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 14:03:46 -07:00
hayeswang
e501139a51 r8152: add pre_reset and post_reset
Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 14:03:46 -07:00
Yijing Wang
6754676297 PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
Rajat Jain reported a deadlock when PCIe hot-add and AER recovery happen at
the same time:

thread 1:

  pciehp_enable_slot
    pciehp_configure_device
      pci_bus_add_devices
        pci_bus_add_device
          device_attach
            device_lock(dev)                       # acquire device lock
            ...
            pciehp_probe
              init_slot
                pci_hp_register
                  pci_create_slot
                    down_write(pci_bus_sem)        # deadlock here

thread 2:

  aer_isr_one_error
    aer_process_err_device
      do_recovery
        broadcast_error_message(..., report_error_detected)
          pci_walk_bus(..., cb=report_error_detected, ...)
            down_read(&pci_bus_sem)                # acquire pci_bus_sem
            report_error_detected(dev)             # cb()
              device_lock(dev)                     # deadlock here

Previously, the bus->devices and bus->slots list were protected by
pci_bus_sem.  In pci_create_slot(), we held it for writing so we could
add to the bus->slots list.

Add a new local pci_slot_mutex to protect bus->slots.  Hold pci_bus_sem for
reading while searching the bus->devices list.

[bhelgaas: changelog]
Link: http://lkml.kernel.org/r/CAA93t1qpPqbih+UB0McA_d_+2rVaNkXsinAUxYzK9+JXSS+L-g@mail.gmail.com
Reported-by: Rajat Jain <rajatja@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-07-30 15:49:10 -05:00
Dan Carpenter
2dc127bb29 hpsa: fix an sprintf() overflow in the reset handler
The string "cmd %d RESET FAILED, new lockup detected" is not quite
large enough so the sprintf() will overflow.  I have increased the size
of the buffer and also changed the sprintf calls to snprintf.

Fixes: 73153fe533 ('hpsa: use block layer tag for command allocation')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-07-30 13:11:40 -07:00
Chris Leech
9c8108a4d3 iSCSI: let session recovery_tmo sysfs writes persist across recovery
The iSCSI session recovery_tmo setting is writeable in sysfs, but it's
also set every time a connection is established when parameters are set
from iscsid over netlink.  That results in the timeout being reset to
the default value after every recovery.

The DM multipath tools want to use the sysfs interface to lower the
default timeout when there are multiple paths to fail over.  It has
caused confusion that we have a writeable sysfs value that seem to keep
resetting itself.

This patch adds an in-kernel flag that gets set once a sysfs write
occurs, and then ignores netlink parameter setting once it's been
modified via the sysfs interface.  My thinking here is that the sysfs
interface is much simpler for external tools to influence the session
timeout, but if we're going to allow it to be modified directly we
should ensure that setting is maintained.

Signed-off-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-07-30 12:43:00 -07:00
Brian King
aaf1b05938 ipr: Driver version 2.6.2
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-07-30 12:41:47 -07:00
Brian King
359d96e73c ipr: Endian / sparse fixes
Some misc fixes for endianness checking with sparse so sparse with
endian checking now runs clean. Fixes a minor bug in the process
which was uncovered by sparse which would result in unnecessary
error recovery for check conditions.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-07-30 12:41:21 -07:00
Wen Xiong
bb8647e86e ipr: Byte swapping for device_id attribute in sysfs
On LE system, users see the wrong device_id attribute. This patch
does necessary byte swapping for device_id attribute and works on
both of LE and BE systems.

Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-07-30 12:39:39 -07:00
Hannes Reinecke
0ae80ba91f scsi: retry MODE SENSE on unit attention
The 'sd' driver is calling scsi_mode_sense() to figure out
internal details. But scsi_mode_sense() never checks for
any pending unit attentions, so we're getting annoying error
messages like:

MODE SENSE: unimplemented page/subpage: 0x00/0x00

and a possible wrong decision for device cache handling.

Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-07-30 12:37:20 -07:00
Jiang Liu
5f2269916b PCI/MSI: Free legacy IRQ when enabling MSI/MSI-X
Once MSI/MSI-X is enabled by the device driver, a PCI device won't use
legacy IRQs again until MSI/MSI-X is disabled.

Call pcibios_free_irq() when enabling MSI/MSI-X and pcibios_alloc_irq()
when disabling MSI/MSI-X.  This allows arch code to manage resources
associated with the legacy IRQ.

[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
2015-07-30 14:17:28 -05:00
Jiang Liu
811a4e6fce PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed
Add pci_has_managed_irq(), pci_set_managed_irq(), and
pci_reset_managed_irq() to simplify code.  No functional change.

[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
2015-07-30 14:13:20 -05:00
Jiang Liu
991de2e590 PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()
To support IOAPIC hotplug, we need to allocate PCI IRQ resources on demand
and free them when not used anymore.

Implement pcibios_alloc_irq() and pcibios_free_irq() to dynamically
allocate and free PCI IRQs.

Remove mp_should_keep_irq(), which is no longer used.

[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
2015-07-30 14:05:57 -05:00
Jiang Liu
890e484758 PCI: Add pcibios_alloc_irq() and pcibios_free_irq()
Add pcibios_alloc_irq() and pcibios_free_irq(), which are called when
binding/unbinding PCI device drivers.

PCI arch code may implement these to manage IRQ resources for hotplugged
devices.

[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
2015-07-30 13:59:47 -05:00
Emmanuel Grumbach
aecdc63d87 iwlwifi: pcie: fix stuck queue detection for sleeping clients
The stuck queue detection mechanism allows to detect queues
that are stuck. For sleeping clients, a queue may rightfully
be stuck: if a poor client implementation stays asleep for
more than 10s, then we don't want to trigger recovery flows
because of that client.
In order to cope with this, I added a mechanism that
monitors the state of the client: when a client goes to
sleep, the timer of his queues is frozen. When he wakes up,
the timer is reset to the right value so that if a client
was awake for more than 10s and the queues are stuck, only
then, the recovery flow will kick in.
This is valid only on non-shared queues: A-MPDU queues.

There was a bug in case we Tx to a sleeping client that has
an empty A-MPDU queue: the timer was armed to now + 10s.
This is bad, but pretty harmless.
The problem is that when the client wakes up, the timer is
modified to be now + remainder. But remainder is 0 since the
queue was empty when that client went to sleep...

Fix this by checking the state of the client before playing
with the timer when we add a packet to an empty queue.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2015-07-30 21:38:14 +03:00
Dudley Du
0642ffd6a8 Input: cyapa - do not try to enable proximity reporting on older devices
Avoid the driver generate warning message when the cyapa driver working
with the old Gen5 trackpad device which does not support the proximity
function.  Those old Gen5 trackpad device all have the platform version
less than 2.

Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-07-30 11:34:00 -07:00
Dudley Du
ddbb299db0 Input: cyapa - introduce device tree binding
Add device tree support for  Cypress trackpad devices.

Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-07-30 11:33:59 -07:00
Dudley Du
36e9615bd7 Input: cyapa - add regulator vcc support
We need to power up the chip before we can initialize it.

On systems that delegate task of powering up regulators to firmware we
assume that we'll be simply given a dummy regulator.

Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-07-30 11:33:59 -07:00
Javier Martinez Canillas
02d9bd05dc Input: touchscreen - export OF module alias information
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.

In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.

And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.

To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-07-30 11:05:37 -07:00
Javier Martinez Canillas
2e9e910e8a Input: export I2C module alias information in missing drivers
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-07-30 11:05:37 -07:00
Linus Torvalds
dbe08116b8 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
 "The main change is support for keyboards and touchpads found in 2015
  editions of Macbooks"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Revert "Input: zforce - don't overwrite the stack"
  Input: bcm5974 - add support for the 2015 Macbook Pro
  HID: apple: Add support for the 2015 Macbook Pro
  Input: bcm5974 - prepare for a new trackpad generation
  Input: synaptics - dump ext10 capabilities as well
2015-07-30 11:03:04 -07:00
Tony Battersby
0c958ecc69 scsi: fix memory leak with scsi-mq
Fix a memory leak with scsi-mq triggered by commands with large data
transfer length.

__sg_alloc_table() sets both table->nents and table->orig_nents to the
same value.  When the scatterlist is DMA-mapped, table->nents is
overwritten with the (possibly smaller) size of the DMA-mapped
scatterlist, while table->orig_nents retains the original size of the
allocated scatterlist.  scsi_free_sgtable() should therefore check
orig_nents instead of nents, and all code that initializes sdb->table
without calling __sg_alloc_table() should set both nents and orig_nents.

Fixes: d285203cf6 ("scsi: add support for a blk-mq based I/O path.")
Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-07-30 10:40:33 -07:00
Brian King
3f1c058131 ipr: Fix invalid array indexing for HRRQ
Fixes another signed / unsigned array indexing bug in the ipr driver.
Currently, when hrrq_index wraps, it becomes a negative number. We
do the modulo, but still have a negative number, so we end up indexing
backwards in the array. Given where the hrrq array is located in memory,
we probably won't actually reference memory we don't own, but nonetheless
ipr is still looking at data within struct ipr_ioa_cfg and interpreting it as
struct ipr_hrr_queue data, so bad things could certainly happen.

Each ipr adapter has anywhere from 1 to 16 HRRQs. By default, we use 2 on new
adapters.  Let's take an example:

Assume ioa_cfg->hrrq_index=0x7fffffffe and ioa_cfg->hrrq_num=4:

The atomic_add_return will then return -1. We mod this with 3 and get -2, add
one and get -1 for an array index.

On adapters which support more than a single HRRQ, we dedicate HRRQ to adapter
initialization and error interrupts so that we can optimize the other queues
for fast path I/O. So all normal I/O uses HRRQ 1-15. So we want to spread the
I/O requests across those HRRQs.

With the default module parameter settings, this bug won't hit, only when
someone sets the ipr.number_of_msix parameter to a value larger than 3 is when
bad things start to happen.

Cc: <stable@vger.kernel.org>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-07-30 10:38:47 -07:00
Brian King
bb7c54339e ipr: Fix incorrect trace indexing
When ipr's internal driver trace was changed to an atomic, a signed/unsigned
bug slipped in which results in us indexing backwards in our memory buffer
writing on memory that does not belong to us. This patch fixes this by removing
the modulo and instead just mask off the low bits.

Cc: <stable@vger.kernel.org>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-07-30 10:38:00 -07:00
Brian King
36b8e180e1 ipr: Fix locking for unit attention handling
Make sure we have the host lock held when calling scsi_report_bus_reset. Fixes
a crash seen as the __devices list in the scsi host was changing as we were
iterating through it.

Cc: <stable@vger.kernel.org>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-07-30 10:36:21 -07:00
Ricardo Neri
9115c7589b efi: Check for NULL efi kernel parameters
Even though it is documented how to specifiy efi parameters, it is
possible to cause a kernel panic due to a dereference of a NULL pointer when
parsing such parameters if "efi" alone is given:

PANIC: early exception 0e rip 10:ffffffff812fb361 error 0 cr2 0
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.2.0-rc1+ #450
[ 0.000000]  ffffffff81fe20a9 ffffffff81e03d50 ffffffff8184bb0f 00000000000003f8
[ 0.000000]  0000000000000000 ffffffff81e03e08 ffffffff81f371a1 64656c62616e6520
[ 0.000000]  0000000000000069 000000000000005f 0000000000000000 0000000000000000
[ 0.000000] Call Trace:
[ 0.000000]  [<ffffffff8184bb0f>] dump_stack+0x45/0x57
[ 0.000000]  [<ffffffff81f371a1>] early_idt_handler_common+0x81/0xae
[ 0.000000]  [<ffffffff812fb361>] ? parse_option_str+0x11/0x90
[ 0.000000]  [<ffffffff81f4dd69>] arch_parse_efi_cmdline+0x15/0x42
[ 0.000000]  [<ffffffff81f376e1>] do_early_param+0x50/0x8a
[ 0.000000]  [<ffffffff8106b1b3>] parse_args+0x1e3/0x400
[ 0.000000]  [<ffffffff81f37a43>] parse_early_options+0x24/0x28
[ 0.000000]  [<ffffffff81f37691>] ? loglevel+0x31/0x31
[ 0.000000]  [<ffffffff81f37a78>] parse_early_param+0x31/0x3d
[ 0.000000]  [<ffffffff81f3ae98>] setup_arch+0x2de/0xc08
[ 0.000000]  [<ffffffff8109629a>] ? vprintk_default+0x1a/0x20
[ 0.000000]  [<ffffffff81f37b20>] start_kernel+0x90/0x423
[ 0.000000]  [<ffffffff81f37495>] x86_64_start_reservations+0x2a/0x2c
[ 0.000000]  [<ffffffff81f37582>] x86_64_start_kernel+0xeb/0xef
[ 0.000000] RIP 0xffffffff81ba2efc

This panic is not reproducible with "efi=" as this will result in a non-NULL
zero-length string.

Thus, verify that the pointer to the parameter string is not NULL. This is
consistent with other parameter-parsing functions which check for NULL pointers.

Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
2015-07-30 18:07:11 +01:00
Greg Kroah-Hartman
e34d572a92 USB-serial fixes for v4.2-rc5
Here's a fix for some Sierra Wireless modems and a couple of new device
 ids.
 
 Signed-off-by: Johan Hovold <johan@kernel.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABAgAGBQJVuje2AAoJEEEN5E/e4bSVj08P/19Nc1SRPatVQWnriDLt0mYX
 tBqELVcjkEk79YRGRvebHbTaZ1wScN17hDR9ThMsDPi57uLytbihmVYia6ZNX9qE
 GnXBqiRmp8jdtK39yUpJ8KtobrF3adGlC6RbKU3U8R5fCSAnyzq6HEhoLBot3m/H
 xpwFBONFt3R8Ym67zRbh5GVu/n56laAxx5C3tFAs0LsAIuj1fMlfVpeTtex8FzgX
 wsGaxfSub1YWjww1vExYHEQaRTTL2TFq38nijZzbysD1JPyX4yxeEoyLbSeuuDXr
 8qzsRBVz49c/SuknAuvCVwcyM9OzR3ZUfZHa/5s+3sCHrPwHsslwYPVs8KcrZAfW
 8B4egi7z/tANi+UJ+rmJRFlJQxLK68JUv0AO3CuunC6PcagnJ4qirAh7wPC8ZzBN
 Pb0jB7rxNQsMPbcv44xMoQN2yOSZaW/g9OYuLLEQfIUNEUpjkxe6Gl9pqbTwllIR
 uC96awWSKRt9GEk23yFTM35EGOEwFJpbYcH51O1o4yEO430iJXImbPkAzMO08KAw
 XE3gINmSib6+uRrzEBieTNXj8Fe/5jsHEqcMZcusTP2h1DFyoMwkCYILXU1IBDJ7
 HC20jqhEBBB54O8Gy8teRXVXjizSmnHHylABCjovtLFQ+B7aoCjs9CtCkTRLmCcQ
 TSsZi6xxWXbo1BgJVapC
 =0bb/
 -----END PGP SIGNATURE-----

Merge tag 'usb-serial-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v4.2-rc5

Here's a fix for some Sierra Wireless modems and a couple of new device
ids.

Signed-off-by: Johan Hovold <johan@kernel.org>
2015-07-30 09:55:17 -07:00
Yuval Mintz
ce7fa78ce1 bnx2x: Fix compilation when CONFIG_BNX2X_SRIOV is not set
Commit 05cc5a39dd ("bnx2x: add vlan filtering offload") has broken
compilation when CONFIG_BNX2X_SRIOV is not set.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 09:52:18 -07:00
Peter Chen
913e4a90b6 usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth
According to USB Audio Device 2.0 Spec, Ch4.10.1.1:
wMaxPacketSize is defined as follows:
Maximum packet size this endpoint is capable of sending or receiving
when this configuration is selected.
This is determined by the audio bandwidth constraints of the endpoint.

In current code, the wMaxPacketSize is defined as the maximum packet size
for ISO endpoint, and it will let the host reserve much more space than
it really needs, so that we can't let more endpoints work together at
one frame.

We find this issue when we try to let 4 f_uac2 gadgets work together [1]
at FS connection.

[1]http://www.spinics.net/lists/linux-usb/msg123478.html

Acked-by: Daniel Mack <zonque@gmail.com>
Cc: andrzej.p@samsung.com
Cc: Daniel Mack <zonque@gmail.com>
Cc: tiwai@suse.de
Cc: <stable@vger.kernel.org> #v3.18+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:38 -05:00
Sanjay Singh Rawat
8078f314b8 usb: gadget: f_mass_storage: stop thread in bind failure case
After the worker thread is launched, bind function is doing further
configuration. In case of failure stop the thread.

Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sanjay Singh Rawat <snjsrwt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:37 -05:00
Dan Carpenter
5feb5d2003 usb: gadget: m66592-udc: forever loop in set_feature()
There is an "&&" vs "||" typo here so this loops 3000 times or if we get
unlucky it could loop forever.

Fixes: ceaa0a6eea ('usb: gadget: m66592-udc: add support for TEST_MODE')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:37 -05:00
Dan Carpenter
1c99cabfc9 usb: gadget: fotg210-udc: remove duplicate conditions
We handle the "if (!req->req.length)" condition at the start of the
function and return.  We can delete this dead code.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:37 -05:00
Ivan T. Ivanov
6f98f545b0 usb: phy: msm: Add D+/D- lines route control
apq8016-sbc board is using Dual SPDT USB Switch (TC7USB40MU),
witch is controlled by GPIO to de/multiplex D+/D- USB lines to
USB2513B Hub and uB connector. Add support for this.

Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:36 -05:00
Robert Baldyga
736d093b59 usb: gadget: apply generic altsetting support check mechanism
Replace calls of gadget_supports_altsettings() function (which check altset
support by comparing UDC controller name with hardcoded names) with
gadget_is_altset_supported() which checks generic quirk bitfield.

Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:36 -05:00
Robert Baldyga
7a896d4052 usb: gadget: f_ecm/f_ncm: check quirk instead of UDC name
Use generic mechanism to check if UDC controller supports zlp.

Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:36 -05:00
Robert Baldyga
a4cc42157f usb: gadget: f_mass_storage: check quirk instead of UDC name
Use generic mechanism to check if UDC controller supports stalling.

Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:36 -05:00
Robert Baldyga
ca1023c81d usb: gadget: add 'quirk_zlp_not_supp' to usb_gadget
Due to some UDC controllers may not support zlp, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.

This patch adds 'quirk_zlp_not_supp' field to struct usb_gadget and helper
function gadget_is_zlp_supported(). It also sets 'quirk_zlp_not_supp'
to 1 in musb UDC driver, which has such limitation.

[ balbi@ti.com : make it build ]

Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:35 -05:00
Robert Baldyga
02ded1b0d8 usb: gadget: add 'quirk_stall_not_supp' to usb_gadget
Due to some UDC controllers may not support stalling, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.

This patch adds 'quirk_stall_not_supp' field to struct usb_gadget and helper
function gadget_is_stall_supported(). It also sets 'quirk_stall_not_supp'
to 1 in at91_udc driver, which has such limitation.

Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:35 -05:00
Robert Baldyga
ffd9a0fcbb usb: gadget: add 'quirk_altset_not_supp' to usb_gadget
Due to some UDC controllers may not support altsettings, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.

This patch adds 'quirk_altset_not_supp' field to struct usb_gadget and helper
function gadget_is_altset_supported(). It also sets 'quirk_altset_not_supp'
to 1 in pxa25x_udc and pxa27x_udc drivers, which have such limitation.

Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:35 -05:00
Kishon Vijay Abraham I
c0bd5456a4 usb: dwc3: ep0: handle non maxpacket aligned transfers > 512
Use chained TRB mechanism to handle non maxpacket aligned transfers
greater than bounce buffer size. With this the first TRB will be programmed
to receive 'ALIGN(ur->length - maxp, maxp)' data and the second TRB
will be programmed to receive the remaining data using bounce buffer.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:35 -05:00
Kishon Vijay Abraham I
2abd9d5fa6 usb: dwc3: ep0: Add chained TRB support
Add chained TRB support to ep0. Now TRB's can be chained just by
invoking _dwc3_ep0_start_trans_ with 'chain' parameter set to true.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:34 -05:00
Kishon Vijay Abraham I
368ca113ca usb: dwc3; ep0: Modify _dwc3_ep0_start_trans_ API to take 'chain' parameter
No functional change. Added a new parameter in _dwc3_ep0_start_trans_ to
indicate whether the TRB is a chained TRB or last TRB. This is in
preparation for adding chained TRB support for ep0.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:34 -05:00
Kishon Vijay Abraham I
8a34422056 usb: dwc3: ep0: preparation for handling non maxpacket aligned transfers > 512
No functional change. This is in preparation for handling non maxpacket
aligned transfers greater than bounce buffer size. This is basically to
avoid code duplication when using chained TRB transfers to handle
non maxpacket aligned transfers greater than bounce buffer size.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:34 -05:00
Kishon Vijay Abraham I
2e5464da4e usb: dwc3: ep0: use _roundup_ to calculate the transfer size
No functional change. Used _roundup_ macro to calculate the transfer
size aligned to maxpacket in  dwc3_ep0_complete_data. It also makes it
similar to how transfer size is calculated in __dwc3_ep0_do_control_data.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:34 -05:00
Kishon Vijay Abraham I
b2fb5b1a0f usb: dwc3: ep0: Fix mem corruption on OUT transfers of more than 512 bytes
DWC3 uses bounce buffer to handle non max packet aligned OUT transfers and
the size of bounce buffer is 512 bytes. However if the host initiates OUT
transfers of size more than 512 bytes (and non max packet aligned), the
driver throws a WARN dump but still programs the TRB to receive more than
512 bytes. This will cause bounce buffer to overflow and corrupt the
adjacent memory locations which can be fatal.

Fix it by programming the TRB to receive a maximum of DWC3_EP0_BOUNCE_SIZE
(512) bytes.

Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-30 11:43:33 -05:00
Michał Pecio
49bda21266 USB: pl2303: fix baud-rate divisor calculations
This commit fixes the following issues:

1. The 9th bit of buf was believed to be the LSB of divisor's
exponent, but the hardware interprets it as MSB (9th bit) of the
mantissa. The exponent is actually one bit shorter and applies
to base 4, not 2 as previously believed.

2. Loop iterations doubled the exponent instead of incrementing.

3. The exponent wasn't checked for overflow.

4. The function returned requested rate instead of actual rate.

Due to issue #2, the old code deviated from the wrong formula
described in #1 and actually yielded correct rates when divisor
was lower than 4096 by using exponents of 0, 2 or 4 base-2,
interpreted as 0, 1, 2 base-4 with the 9th mantissa bit clear.
However, at 93.75 kbaud or less the rate turned out too slow
due to #2 or too fast due to #2 and #3.

I tested this patch by sending and validating 0x00,0x01,..,0xff
to an FTDI dongle at 234, 987, 2401, 9601, 31415, 115199, 250k,
500k, 750k, 1M, 1.5M, 3M+1 baud. All rates passed.

I also used pv to check speed at some rates unsupported by FTDI:
45 (the lowest possible), 2M, 4M, 5M and 6M-1. Looked sane.

Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Fixes: 399aa9a75a ("USB: pl2303: use divisors for unsupported baud
rates")
Cc: stable <stable@vger.kernel.org> # v3.18
[johan: update summary ]
Signed-off-by: Johan Hovold <johan@kernel.org>
2015-07-30 18:11:07 +02:00
Linus Torvalds
0a552051a4 Two patches headed for -stable.
nct7802: Fix integer overflow seen when writing voltage limits
 nct7904: Rename pwm attributes to match hwmon ABI
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJVuZTpAAoJEMsfJm/On5mBlNIP/0olmsXqXiAwaUfksLbv9nMF
 fBriG9J39VHconorUhaMK5ugKxLTHoYP1AFSYGAIlgb10x5xEN3IsjtQ7NZCfwMf
 JD4V1fBF+2Vgec8662+dNkvbIAaXJnO+CLMy9OU9nTiRC8wNHG0UiDGRXAZSuCuu
 uDayrXXj05XSfs3xobZ58WXXcQNbkK7q6h1C2yP7N6k1xcWtu7mwK2dcQu0ZeUgf
 wn8vdSKLcdofnfvt0ckm0joObyzWeyzINS2BMyJh7yr/cZyPHuPVOCZaD1Kjy0ts
 +PVoibDmtN9l/KlZ3y7a6XHd45JmNbLkFUxnAkPmoLlNUpleNTGjW0c+ffwsn53P
 HzS5Qqc5X/A59J2a539KHsvE0QHAhmA2m+XjVsq5Kx4qcl7suRE/7GbwqWzMt2OP
 fPzMXcWd+G75oix9vC5SAFdm88vPVTs27j7qSnr+Cte3k49XYegCB3GPFrQHqAzP
 dTkri7sWFhOQByl0kwIbl1oa5lazcN1nd1YjPfszPFyErG8b7FtE8XktpQfSZ6/d
 QPzwXyHE2GgTxW4d3eMYpeslLBimSQSe51S/zL+Zvg263JHIpIH/j7/K7Fk5uRh6
 WXhnmmFrBVVOztOXvskL7AJ8hgghOHDAkrz6RmMG8KpHcpFnzYz7/O313SzotLNc
 HfLwctCm8hEwCzA09495
 =KC6y
 -----END PGP SIGNATURE-----

Merge tag 'hwmon-for-linus-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Two patches headed for -stable.

  nct7802: Fix integer overflow seen when writing voltage limits
  nct7904: Rename pwm attributes to match hwmon ABI"

* tag 'hwmon-for-linus-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (nct7802) Fix integer overflow seen when writing voltage limits
  hwmon: (nct7904) Rename pwm attributes to match hwmon ABI
2015-07-30 08:04:19 -07:00
Chris Wilson
5eb3e5a5e1 drm/i915: Declare the swizzling unknown for L-shaped configurations
The old style of memory interleaving swizzled upto the end of the
first even bank of memory, and then used the remainder as unswizzled on
the unpaired bank - i.e. swizzling is not constant for all memory. This
causes problems when we try to migrate memory and so the kernel prevents
migration at all when we detect L-shaped inconsistent swizzling.
However, this issue also extends to userspace who try to manually detile
into memory as the swizzling for an individual page is unknown (it
depends on its physical address only known to the kernel), userspace
cannot correctly swizzle.

Note that this is a new attempt for the previously merged one,
reverted in

commit d82c0ba6e3
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Tue Jul 14 12:29:27 2015 +0200

    Revert "drm/i915: Declare the swizzling unknown for L-shaped configurations"

This is cc: stable since we need it to fix up troubles with wc cpu
mmaps that userspace recently started to use widely.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91105
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
[danvet: Add note about previous (failed attempt).]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-07-30 16:51:20 +02:00
Chris Wilson
d0e30adc42 drm/i915: Mark PIN_USER binding as GLOBAL_BIND without the aliasing ppgtt
If the device does not support the aliasing ppgtt, we must translate
user bind requests (PIN_USER) from LOCAL_BIND to a GLOBAL_BIND. However,
since this is device specific we cannot do this conveniently in the
upper layers and so must manage the vma->bound flags in the backend.

Partial revert of commit 75d04a3773 [4.2-rc1]
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Tue Apr 28 17:56:17 2015 +0300

    drm/i915/gtt: Allocate va range only if vma is not bound

Note this was spotted by Daniel originally, but we dropped the ball in
getting the fix in before the bug going wild. Sorry all.

Reported-by: Vincent Legoll vincent.legoll@gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91133
References: https://bugs.freedesktop.org/show_bug.cgi?id=90224
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-07-30 16:45:30 +02:00