Commit graph

287,481 commits

Author SHA1 Message Date
Peter Oh
ae7d3821a7 ath10k: initialize msdu ext. descriptor before use
Initial QCA99X0 support has a known issue with TCP Tx throughput.
All other path such as UDP Tx/Rx and TCP Rx meet their expectation
(> 900Mbps), but TCP Tx marked as low as 5Mbps when single pair is
used on iperf.

The root cause is turned out because TSO flag is not initialized
properly so that firmware configures TSO in wrong way.
TSO flags in msdu extension descriptor is required to be reset
to indicate firmware there is no TSO is enabled, otherwise it
could act as TSO is enabled which causes huge throughput drop.

In fact, it's enough by resetting TSO flags only to prevent the
unexpected behavior, but initializing whole msdu ext. descriptor
will help to clear uncertainty of firmware could bring on as it
constantly updated.

Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-30 17:05:29 +03:00
Vasanthakumar Thiagarajan
8a055a8adc ath10k: add QCA99X0 to supported device list
Add vendor/device id of QCA99X0 V2.0 to pci id table and
QCA99X0_HW_2_0_CHIP_ID_REV to ath10k_pci_supp_chips[] for
QCA99X0 to get detected by the driver.

kvalo: now QCA99X0 family of chipsets is supported by ath10k.
Tested client, AP and monitor mode with QCA9990.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-30 17:04:00 +03:00
Raja Mani
1201844e6d ath10k: increase max client to 512 in qca99x0
When max client was set to 512 in qca99x0, there was host memory
alloc failure during wmi service ready event handling. This issue
got resolved now, increasing max client limit from 256 to 512.

Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-30 16:54:57 +03:00
Raja Mani
c8ecfc1c33 ath10k: fix memory alloc failure in qca99x0 during wmi svc rdy event
Host memory required for firmware is allocated while handling
wmi service ready event. Right now, wmi service ready is handled
in tasklet context and it calls dma_alloc_coherent() with atomic
flag (GFP_ATOMIC) to allocate memory in host needed for firmware.
The problem is, dma_alloc_coherent() with GFP_ATOMIC fails in
the platform (at least in AP platform) where it has less atomic
pool memory (< 2mb). QCA99X0 requires around 2 MB of host memory
for one card, having additional QCA99X0 card in the same platform
will require similarly amount of memory. So, it's not guaranteed that
all the platform will have enough atomic memory pool.

Fix this issue, by handling wmi service ready event in workqueue
context and calling dma_alloc_coherent() with GFP_KERNEL. mac80211 work
queue will not be ready at the time of handling wmi service ready.
So, it can't be used to handle wmi service ready. Also, register work
gets scheduled during insmod in existing ath10k_wq and waits for
wmi service ready to completed. Both workqueue can't be used for
this purpose. New auxiliary workqueue is added to handle wmi service
ready.

Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-07-30 16:54:28 +03:00
Dan Streetman
844190dbeb crypto: nx - use be32_to_cpu for __be32 field in debug msg
One of the debug messages in the NX 842 PowerNV driver is missing
the required be32_to_cpu() wrapper when accessing the __be32 field
csb->count.  Add the wrapper so the message will show the correct count.

Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2015-07-30 21:49:41 +08:00
Dan Streetman
7371c0a5c2 crypto: nx - don't err if compressed output > input
Return success instead of error if compression succeeds but the output is
larger than the input.

It's unlikely that the caller will use the compressed data since it's
larger than the original uncompressed data, but there was no error and
returning an error code is incorrect.  Further, for testing small input
buffers, the output is likely to be larger than the input and success
needs to be returned to verify the test.

Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2015-07-30 21:49:40 +08:00
Alexander Aring
8b44f0dd2f at86rf230: remove hrtimer on 1 usec delay
According Documentation/timers/timers-howto.txt the usually case for
setting up a hrtimer takes > ~10us. So we should use udelay in this
case so we are sure that the state change was done, before doing the
state change assert.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-30 14:02:21 +02:00
Daniel Drake
d63b282645 Bluetooth: btusb: match generic class code in interface descriptor
btusb currently has a generic match on USB device descriptors:
        { USB_DEVICE_INFO(0xe0, 0x01, 0x01) },

However, http://www.usb.org/developers/defined_class states:

  Base Class E0h (Wireless Controller)
  This base class is defined for devices that are Wireless controllers.
  Values not shown in the table below are reserved. These class codes are
  to be used in Interface Descriptors, with the exception of the Bluetooth
  class code which can also be used in a Device Descriptor.

Add a match on the interface descriptors accordingly.

This fixes compatibility with the RTL8723AU device shown below.
This device conforms to the USB Interface Association Descriptor
specification, which requires the device to have class ef/02/01.
The extra IAD descriptor then specifies that interfaces 0 and 1
belong to the same function/driver, which is true. Provided that
the Bluetooth device class spec accepts use of the IAD, I imagine that
technically, all btusb devices should be configured like this.

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=0724 Rev= 2.00
S:  Manufacturer=Realtek
S:  Product=802.11n WLAN Adapter
S:  SerialNumber=00e04c000001
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8723au
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=500us

Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-30 13:42:26 +02:00
Frederic Danis
4a546ec364 Bluetooth: btbcm: Add BCM4330B1 UART device
Add "waiting for configuration" address.
Add lmp_subver and firmware name for BCM4330B1 controller.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-07-30 13:18:08 +02:00
Joerg Roedel
5271782835 iommu/amd: Set global dma_ops if swiotlb is disabled
Some AMD systems also have non-PCI devices which can do DMA.
Those can't be handled by the AMD IOMMU, as the hardware can
only handle PCI. These devices would end up with no dma_ops,
as neither the per-device nor the global dma_ops will get
set. SWIOTLB provides global dma_ops when it is active, so
make sure there are global dma_ops too when swiotlb is
disabled.

Signed-off-by: Joerg Roedel <jroedel@suse.de>
2015-07-30 10:28:48 +02:00
Joerg Roedel
3230232457 iommu/amd: Use swiotlb in passthrough mode
In passthrough mode (iommu=pt) all devices are identity
mapped. If a device does not support 64bit DMA it might
still need remapping. Make sure swiotlb is initialized to
provide this remapping.

Signed-off-by: Joerg Roedel <jroedel@suse.de>
2015-07-30 10:28:48 +02:00
Joerg Roedel
02ca20212f iommu/amd: Allow non-IOMMUv2 devices in IOMMUv2 domains
Since devices with IOMMUv2 functionality might be in the
same group as devices without it, allow those devices in
IOMMUv2 domains too.
Otherwise attaching the group with the IOMMUv2 device to the
domain will fail.

Signed-off-by: Joerg Roedel <jroedel@suse.de>
2015-07-30 10:28:48 +02:00
Joerg Roedel
1e6a7b04c0 iommu/amd: Use iommu core for passthrough mode
Remove the AMD IOMMU driver implementation for passthrough
mode and rely on the new iommu core features for that.

Signed-off-by: Joerg Roedel <jroedel@suse.de>
2015-07-30 10:28:48 +02:00
Joerg Roedel
55c99a4dc5 iommu/amd: Use iommu_attach_group()
Since the conversion to default domains the
iommu_attach_device function only works for devices with
their own group. But this isn't always true for current
IOMMUv2 capable devices, so use iommu_attach_group instead.

Signed-off-by: Joerg Roedel <jroedel@suse.de>
2015-07-30 10:28:48 +02:00
Jiri Pirko
31557f0f97 mlxsw: Introduce Mellanox SwitchX-2 ASIC support
Benefit from the previously introduced Mellanox Switch infrastructure and
add driver for SwitchX-2 ASIC. Note that this driver is very simple now.
It implements bare minimum for getting device to work on slow-path.
Fast-path offload functionality is going to be added soon.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 00:05:00 -07:00
Ido Schimmel
4ec14b7634 mlxsw: Add interface to access registers and process events
Ethernet Management Datagrams (EMADs) are Ethernet packets sent between
the host and the device in order to configure the available device registers.
Another use case is notifications sent from the device to the host,
letting it know about certain events, such as port up / down.

Add the ability to construct EMADs with provisions to construct and
parse the registers' payloads. Implement EMAD transaction layer
which is responsible for the reliable transmission of EMADs. Also, add
an infrastructure used by the switch driver to register for particular
events generated by the device.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 00:05:00 -07:00
Jiri Pirko
eda6500a98 mlxsw: Add PCI bus implementation
Add PCI bus implementation for Mellanox Technologies Switch ASICs. This
includes firmware initialization, async queues manipulation and command
interface implementation.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 00:04:59 -07:00
Jiri Pirko
93c1edb27f mlxsw: Introduce Mellanox switch driver core
Add core components of Mellanox switch driver infrastructure.
Core infrastructure is designed so that it can be used by multiple
bus drivers (PCI now, I2C and SGMII are planned to be implemented
in the future). Multiple switch kind drivers can be registered as well.
This core serves as a glue between buses and drivers.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-30 00:04:59 -07:00
Shahed Shaikh
15f1bb1f1e qlcnic: Fix corruption while copying
Use proper typecasting while performing byte-by-byte copy

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:57:26 -07:00
Sriharsha Basavapatna
8670f2a5ac be2net: Support vxlan offload stats in the driver
This patch adds vxlan offload specific counters to ethtool stats. We
provide tx/rx queue counters to show the number of vxlan offload pkts
sent/received.

Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:54:05 -07:00
Thanneeru Srinivasulu
60f83c8987 net: thunderx: Fix for crash while BGX teardown
Cortina phy does not have kernel driver and we don't attach
device with phy layer for intefaces like XFI, XLAUI etc,
Hence check for interface type before calling disconnect.

Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:32 -07:00
Sunil Goutham
4adf435114 net: thunderx: Add PCI driver shutdown routine
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:32 -07:00
Sunil Goutham
b49087dd0f net: thunderx: Fix crash when changing rss with mutliple traffic flows
This fixes a crash when changing rss with multiple traffic flows.

While interface teardown, disable tx queues after all NAPI threads
are done. If done otherwise tx queues might be woken up inside NAPI
if any CQE_TX are processed.

Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:32 -07:00
Sunil Goutham
3d7a8aaad8 net: thunderx: Set watchdog timeout value
If a txq (SQ) remains in stopped state after this timeout its
considered as stuck and interface is reinited.

Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:32 -07:00
Sunil Goutham
74840b83bd net: thunderx: Wakeup TXQ only if CQE_TX are processed
Previously TXQ is wakedup whenever napi is executed
and irrespective of if any CQE_TX are processed or not.
Added 'txq_stop' and 'txq_wake' counters to aid in debugging
if there are any future issues.

Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:31 -07:00
Sunil Goutham
f8ce9666fa net: thunderx: Suppress alloc_pages() failure warnings
Suppressing standard alloc_pages() warnings. Some kernel configs limit
alloc size and the network driver may fail. Do not drop a kernel
warning in this case, instead just drop a oneliner that the network
driver could not be loaded since the buffer could not be allocated.

Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:31 -07:00
Sunil Goutham
2cb468e01e net: thunderx: Fix TSO packet statistic
Fixing TSO packages not being counted.

Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:31 -07:00
Sunil Goutham
c62cd3c451 net: thunderx: Fix memory leak when changing queue count
Fix for memory leak when changing queue/channel count via ethtool

Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:31 -07:00
Sunil Goutham
32c1b965f4 net: thunderx: Fix RQ_DROP miscalculation
With earlier configured value sufficient number of CQEs are not
being reserved for transmitted packets. Hence under heavy incoming
traffic load, receive notifications will take away most of the CQ
thus transmit notifications will be lost resulting in tx skbs not
being freed.

Finally SQ will be full and it will be stopped, watchdog timer
will kick in. After this fix receive notifications will not take
morethan half of CQ reserving the rest for transmit notifications.

Also changed CQ & SQ sizes from 16k to 4k.
This is also due to the receive notifications taking first half of
CQ under heavy load and time taken by NAPI to clear transmit notifications
will increase with higher queue sizes. Again results in SQ being stopped.

Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:31 -07:00
Sunil Goutham
143ceb0b8a net: thunderx: Fix memory leak while tearing down interface
Fixed 'tso_hdrs' memory not being freed properly.
Also fixed SQ skbuff maintenance issues.

Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:30 -07:00
Sunil Goutham
4b561c17d9 net: thunderx: Fix data integrity issues with LDWB
Switching back to LDD transactions from LDWB.

While transmitting packets out with LDWB transactions
data integrity issues are seen very frequently.
hence switching back to LDD.

Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:52:30 -07:00
Oded Gabbay
a63c580a52 drm/amdkfd: fix bug when initializing sdma vm
A logical AND operation was used during mask and shift, instead of a
bitwise AND operation. This patch fixes this bug by changing the
operation to bitwise AND.

Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
2015-07-30 09:26:15 +03:00
Oded Gabbay
e8a64b20eb drm/amdgpu: fix bug when amdkfd destroys hqd
The wrong define was used to check if the hqd is still active

v2: Don't use SHIFT as the MASK is already shifted

Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
2015-07-30 09:26:00 +03:00
Yuval Mintz
05cc5a39dd bnx2x: add vlan filtering offload
Current driver always uses vlan-promisc mode, i.e., it receives both
tagged and untagged traffic and lets the network stack drop packets
tagged with unrequested vlan tags.

This patch implements vlan-filtering offload in the driver -
Unless explicitly configured to promisc mode, only untagged packets or
packets tagged with requested vlans would reach the Rx flow.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:24:45 -07:00
Achiad Shochat
98e81b0ad6 net/mlx5e: Remove the mlx5e_update_priv_params() function
It was used to update netdev priv parameters that require stopping
and re-opening the device in a generic way - it got the new
parameters and did: ndo_stop(), copy new parameters into current
parameters, ndo_open().

We chose to remove it for two reasons:
1) It requires additional instance of struct mlx5e_params on the
   stack and looking forward we expect this struct to grow.
2) Sometimes we want to do additional operations (besides
   just updating the priv parameters) while the netdev is stopped.
   For example, updating netdev->mtu @mlx5e_change_mtu() should
   be done while the netdev is stopped (done in this commit).

Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:04:47 -07:00
Achiad Shochat
1fc22739a8 net/mlx5e: Introduce create/destroy RSS indir table access functions
Introduce access functions to create/destroy RSS indrection table
and use it in the Ethernet driver.

Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:04:47 -07:00
Achiad Shochat
1f2a30037b net/mlx5e: Do not use netdev_err() before the netdev is registered
Since it is un-named at this time.

Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:04:46 -07:00
Achiad Shochat
97de9f310a net/mlx5e: Avoid redundant de-reference
Use the already defined rq pointer directly.

Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:04:46 -07:00
Achiad Shochat
28abbfddf4 net/mlx5e: Remove redundant assignment of sq->user_index
It is not needed by the mlx5 Eth driver since it has a CQ per RQ/SQ.

Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:04:46 -07:00
Achiad Shochat
a4418a6c36 net/mlx5e: Remove redundant field mlx5e_priv->num_tc
This field already exists under the mlx5e_params struct

Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:04:46 -07:00
Achiad Shochat
68cdf5d6e9 net/mlx5e: Use hard-coded 4K page size for RQ/SQ/CQ
The page size of the device's RQ/SQ/CQ objects is defined in 4K
units regardless of the system pages size.
Thus using the Linux's PAGE_SHIFT macro yields wrong device
configuration in systems where PAGE_SHIFT!=12.

Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:04:46 -07:00
Haggai Abramonvsky
c928ed5517 net/mlx5_core: Check the return value of mlx5_command_exec()
mlx5_cmd_exec() might fail - need to check return value.

Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 23:04:46 -07:00
Scott Wood
b4b67f269d gianfar: Fix warnings when built on 64-bit
As part of defconfig consolidation using fragments, we'd like to be
able to have the same drivers enabled on 32-bit and 64-bit.  Gianfar
happens to only exist on 32-bit systems, and when building the
resulting 64-bit kernel warnings were produced.

A couple of the warnings are trivial, but the rfbptr code has deeper
issues.  It uses the virtual address as the DMA address, which again,
happens to work in the environments where this driver is currently
used, but is not the right thing to do.

Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation
support")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 22:57:24 -07:00
Guenter Roeck
9200bc4c28 hwmon: (nct7802) Fix integer overflow seen when writing voltage limits
Writing a large value into a voltage limit attribute can result
in an overflow due to an auto-conversion from unsigned long to
unsigned int.

Cc: Constantine Shulyupin <const@MakeLinux.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2015-07-29 20:06:50 -07:00
Guenter Roeck
0d6aaffc3a hwmon: (nct7904) Rename pwm attributes to match hwmon ABI
pwm attributes have well defined names, which should be used.

Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Cc: stable@vger.kernel.org #v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2015-07-29 20:06:46 -07:00
Dave Airlie
bdce3e7c72 Merge branch 'msm-fixes-4.2' of git://people.freedesktop.org/~robclark/linux into drm-fixes
Fix for nasty crash on mdp4 in disable path, fix for dma-buf export,
smb leak on mdp5 which could result in intermittent modeset fails, and
don't let interrupted system call disturb atomic commit once we are
past the point of no return.

* 'msm-fixes-4.2' of git://people.freedesktop.org/~robclark/linux:
  drm/msm/mdp5: release SMB (shared memory blocks) in various cases
  drm/msm: change to uninterruptible wait in atomic commit
  drm/msm: mdp4: Fix drm_framebuffer dereference crash
  drm/msm: fix msm_gem_prime_get_sg_table()
2015-07-30 12:41:44 +10:00
Karicheri, Muralidharan
31a184b7ac net: netcp: ethss: cleanup gbe_probe() and gbe_remove() functions
This patch clean up error handle code to use goto label properly. In some
cases, the code unnecessarily use goto instead of just returning the error
code.  Code also make explicit calls to devm_* APIs on error which is
not necessary. In the gbe_remove() also it makes similar calls which is
also unnecessary.

Also fix few checkpatch warnings

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 18:37:41 -07:00
Karicheri, Muralidharan
c20afae75c net: netcp: ethss: fix up incorrect use of list api
The code seems to assume a null is returned when the list is empty
from first_sec_slave() to break the loop which is incorrect. Fix the
code by using list_empty().

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 18:37:40 -07:00
Karicheri, Muralidharan
01a030996e net: netcp: fix cleanup interface list in netcp_remove()
Currently if user do rmmod keystone_netcp.ko following warning is
seen :-

[   59.035891] ------------[ cut here ]------------
[   59.040535] WARNING: CPU: 2 PID: 1619 at drivers/net/ethernet/ti/
netcp_core.c:2127 netcp_remove)

This is because the interface list is not cleaned up in netcp_remove.
This patch fixes this. Also fix some checkpatch related warnings.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-29 18:37:40 -07:00
Linus Torvalds
d41a83ba4b Power management and ACPI fixes for v4.2-rc5
- Fix a recently introduced issue in the cpufreq core causing
    it to attempt to create duplicate symbolic links to the policy
    directory in sysfs for CPUs that are offline when the cpufreq
    driver is being registered (Rafael J Wysocki).
 
  - Fix a recently introduced problem in the ACPI device power
    management core code causing it to store an incorrect value
    in the device object's power.state field in some cases which
    in turn leads to attempts to turn power resources off while
    they should still be on going forward (Mika Westerberg).
 
  - Fix an intel_pstate driver issue introduced during the 4.1 cycle
    which leads to kernel panics on boot on Knights Landing chips due
    to incomplete support for them in that driver (Lukasz Anaczkowski).
 
 /
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABCAAGBQJVuUbwAAoJEILEb/54YlRxb64P/jtDaEmhvMDLnOAP/8/+v+Hq
 kRLF2T+zcX7yu1wEjqWsO94ir+IYX51rbIkMp0rt8+m/CqhTF8QyqvQgaxW2fMAj
 KA6++qT/c+8yeTdSSoxDSV4ux3Ax+d22Q560NOqIFFKK0b+IRSTVirzjyhcMrBJS
 iiaTS8R6o19BttjZrJw4SRnNBXoAeEHeVlMXOqk3S6lq/b89XGIqG93mzaXsFUdz
 xXmkkqudP6z5+jymmiTGp0X+sIpDlR7UruZnk0hZZbEEdmEodlkVFOtYQEV1cro1
 +e3lhMcvG1uO5Sxb5nabKtq8J8rG/buKP+vvsBifKrkxNZMSdnjVvHKxqooVkKVt
 MwGUrjnZhE1dvgL9QvnDNlafitRmrPtolohZ1v7YEXjhsvbbZafr8kkXgo+OmwUs
 wPYmzRg5H2+Di9jhms6hV1z89GtyzsVVOigf3cQZd7hBye4ZsPdWVx0QMyU+0+nC
 GXRRl/8zKyCWCRdnnBwokWs3wiMUAGJ998WPtgo9LhhCXV/JxKIzTXDq+vYxUJ7g
 Z5tbtg7Sgg4VH6WqVQC07x24FFwXKLVtrKd60x0/gbGXYCf7TPwO2dQKjaiF4cHb
 4XSdc2RDEUd2uV7r22j8MaHkPEC33V/Z76nVL49wu8TE4/n0KF6O0+RXMB9Mvsmr
 iZ/CV3rgDFfhf3trOC9v
 =tXB4
 -----END PGP SIGNATURE-----

Merge tag 'pm+acpi-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management and ACPI fixes from Rafael Wysocki:
 "These fix three regressions, two recent ones (cpufreq core and ACPI
  device power management) and one introduced during the 4.1 cycle
  (intel_pstate).

  Specifics:

   - Fix a recently introduced issue in the cpufreq core causing it to
     attempt to create duplicate symbolic links to the policy directory
     in sysfs for CPUs that are offline when the cpufreq driver is being
     registered (Rafael J Wysocki)

   - Fix a recently introduced problem in the ACPI device power
     management core code causing it to store an incorrect value in the
     device object's power.state field in some cases which in turn leads
     to attempts to turn power resources off while they should still be
     on going forward (Mika Westerberg)

   - Fix an intel_pstate driver issue introduced during the 4.1 cycle
     which leads to kernel panics on boot on Knights Landing chips due
     to incomplete support for them in that driver (Lukasz Anaczkowski)"

* tag 'pm+acpi-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: Avoid attempts to create duplicate symbolic links
  ACPI / PM: Use target_state to set the device power state
  intel_pstate: Add get_scaling cpu_defaults param to Knights Landing
2015-07-29 18:14:48 -07:00