The current iProc BCMA front-end driver can only work on ARM32 based
platforms; therefore its config option in Kconfig should be changed to
reflect that. This fixes arm64 allmodconfig build failure when compiling
the the iProc BCMA driver that contains struct pci_sys_data that is
arm32 specific
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
PCI: iproc: Add arm64 support
Add arm64 support to the iProc PCIe driver.
Note that on arm32, bus->sysdata points to the arm32-specific
pci_sys_data struct, and pci_sys_data.private_data contains the
iproc_pcie pointer. For arm64, there's nothing corresponding to
pci_sys_data, so we keep the iproc_pcie pointer directly in
bus->sysdata.
In addition, arm64 does IRQ mapping in pcibios_add_device(), so it
doesn't need pci_fixup_irqs() as arm32 does.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
hdp flush is not needed for IBs that dispatched from kernel inside
because there is no video memory host access
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
compute ring didn't use const engine byfar, so ignore CE things in
compute routine
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
We recently changed the drm_amdgpu_info_device struct so now there is
a 4 byte hole at the end. We need to initialize it so we don't disclose
secret information from the stack.
Fixes: fa92754e9c ('drm/amdgpu: add VCE harvesting instance query')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we fail during device init, record what state each
block is in so that we can tear down clearly.
Fixes various problems on device init failure.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes a broken hsync start value uncovered by:
abc0b1447d
(drm: Perform basic sanity checks on probed modes)
The driver handled the bad hsync start elsewhere, but
the above commit prevented it from getting added.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=91401
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
1. Always assign audio function pointers even if the display does
not support audio. We need to properly disable the audio stream
when when using a non-audio capable monitor. Fixes purple line
on some hdmi monitors.
2. Check if a pin is in use by another encoder before disabling
it.
v2: make sure we've fetched the edid before checking audio and
look up the encoder before calling audio_detect since
connector->encoder may not be assigned yet. Separate
pin and afmt. They are allocated at different times and
have no dependency on eachother.
v3: fix connector fetching in encoder functions
v4: fix missed dig->pin check in dce6_afmt_write_latency_fields
bugs:
https://bugzilla.kernel.org/show_bug.cgi?id=93701https://bugzilla.redhat.com/show_bug.cgi?id=1236337https://bugs.freedesktop.org/show_bug.cgi?id=91041
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Fix mistakenly used, hard coded, port number in get_phv_bit()
Fixes: 77fc29c ("net/mlx4_core: Preparations for 802.1ad VLAN support")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver for the Resource Power Manager (RPM) found in Qualcomm 8974 based
devices.
The driver exposes resources that child drivers can operate on; to
implementing regulator, clock and bus frequency drivers.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This adds the Qualcomm Shared Memory Driver (SMD) providing
communication channels to remote processors, ontop of SMEM.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Commit 665022d72f ("dm cache: avoid calls to prealloc_free_structs() if
possible") introduced a regression that caused the removal of a DM cache
device to hang in cache_postsuspend()'s call to wait_for_migrations()
with the following stack trace:
[<ffffffff81651457>] schedule+0x37/0x80
[<ffffffffa041e21b>] cache_postsuspend+0xbb/0x470 [dm_cache]
[<ffffffff810ba970>] ? prepare_to_wait_event+0xf0/0xf0
[<ffffffffa0006f77>] dm_table_postsuspend_targets+0x47/0x60 [dm_mod]
[<ffffffffa0001eb5>] __dm_destroy+0x215/0x250 [dm_mod]
[<ffffffffa0004113>] dm_destroy+0x13/0x20 [dm_mod]
[<ffffffffa00098cd>] dev_remove+0x10d/0x170 [dm_mod]
[<ffffffffa00097c0>] ? dev_suspend+0x240/0x240 [dm_mod]
[<ffffffffa0009f85>] ctl_ioctl+0x255/0x4d0 [dm_mod]
[<ffffffff8127ac00>] ? SYSC_semtimedop+0x280/0xe10
[<ffffffffa000a213>] dm_ctl_ioctl+0x13/0x20 [dm_mod]
[<ffffffff811fd432>] do_vfs_ioctl+0x2d2/0x4b0
[<ffffffff81117d5f>] ? __audit_syscall_entry+0xaf/0x100
[<ffffffff81022636>] ? do_audit_syscall_entry+0x66/0x70
[<ffffffff811fd689>] SyS_ioctl+0x79/0x90
[<ffffffff81023e58>] ? syscall_trace_leave+0xb8/0x110
[<ffffffff81654f6e>] entry_SYSCALL_64_fastpath+0x12/0x71
Fix this by accounting for the call to prealloc_data_structs()
immediately _before_ the call as opposed to after. This is needed
because it is possible to break out of the control loop after the call
to prealloc_data_structs() but before prealloc_used was set to true.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This reverts commit 386cb7cdee.
Taking the wake_worker() out of free_migration() will slow writeback
dramatically, and hence adaptability.
Say we have 10k blocks that need writing back, but are only able to
issue 5 concurrently due to the migration bandwidth: it's imperative
that we wake_worker() immediately after migration completion; waiting
for the next 1 second wake up (via do_waker) means it'll take a long
time to write that all back.
Reported-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The ">" should be ">=" or we end up reading beyond the end of the array.
Fixes: 6e973d2c43 ('clk: vexpress: Add separate SP810 driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This resulted in the use of polling mode when other approaches
(dma or interrupts) would have been more appropriate.
Happened for transfers longer than 477 bytes.
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.
This did not show when using native-CS, as the same register
is used to control cs as well as polarity, so the changes came
into effect at the same time. Unfortunately this is not true
with gpio-cs.
To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.
Also fixes resetting 3-wire mode after use of rx-mode, so that
a 3-Wire sequence TX, RX, TX works as well (right now it runs
TX, RX, RX instead)
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Pull SCSI target fixes from Nicholas Bellinger:
"This series is larger than what I'd normally be conformable with
sending for a -rc5 PULL request..
However, the bulk of the series is localized to qla2xxx target
specific fixes that address a number of real-world correctness issues,
that have been outstanding on the list for ~6 weeks now. They where
submitted + verified + acked by the HW LLD vendor, contributed by a
major production customer of the code, and are marked for v3.18.y
stable code.
That said, I don't see a good reason to wait another month to get
these fixes into mainline.
Beyond the qla2xx specific fixes, this series also includes:
- bugfix for a long standing use-after-free in iscsi-target during
TPG shutdown + demo-mode sessions.
- bugfix for a >= v4.0 regression OOPs in iscsi-target during a
iscsi_start_kthreads() failure.
- bugfix for a >= v4.0 regression hang in iscsi-target for iser
explicit session/connection logout.
- bugfix for a iser-target bug where a early CMA REJECTED status
during login triggers a NULL pointer dereference OOPs.
- bugfixes for a handful of v4.2-rc1 specific regressions related to
the larger set of recent backend configfs attribute changes.
A big thanks to QLogic + Pure Storage for the qla2xxx target bugfixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
Documentation/target: Fix tcm_mod_builder.py build breakage
iser-target: Fix REJECT CM event use-after-free OOPs
iscsi-target: Fix iser explicit logout TX kthread leak
iscsi-target: Fix iscsit_start_kthreads failure OOPs
iscsi-target: Fix use-after-free during TPG session shutdown
qla2xxx: terminate exchange when command is aborted by LIO
qla2xxx: drop cmds/tmrs arrived while session is being deleted
qla2xxx: disable scsi_transport_fc registration in target mode
qla2xxx: added sess generations to detect RSCN update races
qla2xxx: Abort stale cmds on qla_tgt_wq when plogi arrives
qla2xxx: delay plogi/prli ack until existing sessions are deleted
qla2xxx: cleanup cmd in qla workqueue before processing TMR
qla2xxx: kill sessions/log out initiator on RSCN and port down events
qla2xxx: fix command initialization in target mode.
qla2xxx: Remove msleep in qlt_send_term_exchange
qla2xxx: adjust debug flags
qla2xxx: release request queue reservation.
qla2xxx: Add flush after updating ATIOQ consumer index.
qla2xxx: Enable target mode for ISP27XX
qla2xxx: Fix hardware lock/unlock issue causing kernel panic.
...
These changes allow a PHY driver to trigger a VBUS interrupt and
to provide the value of VBUS.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
ether unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
composite unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate usb otg descriptor and initialize it according to gadget's otg
capabilities, if usb_otg_caps is not set, keep settings as current gadget
drivers. With this 2 new interfaces, gadget can use usb_otg_descriptor
for OTG 1.x, and usb_otg20_descriptor for OTG 2.0 or above, and otg
features can be decided by the combination of usb hardware property
and driver config.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After introduce usb otg properties, update ci_otg_is_fsm_mode conditions
to be depending on both usb hardware properties and usb driver config,
also resolve a compile issue in debug.c after the API change.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Init and update otg capabilities by DT, set gadget's otg capabilities
accordingly.
Acked-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Check property of usb hardware to update otg version and disable SRP, HNP
and ADP if its disable flag is present.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Copy usb_otg_descriptor from config's descriptor if host requests
USB_DT_OTG.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The A33 SoC uses the same musb controller as found on the A31 and later,
but allwinner has removed the configdata register, this commit adds special
handling for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The A31 SoC uses the same musb controller as found in earlier SoCs, but it
is hooked up slightly different. Its SRAM is private and no longer controlled
through the SRAM controller, and its reset is controlled via a separate
reset controller. This commit adds support for this setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is based on initial code to get the Allwinner sunxi musb controller
supported by Chen-Yu Tsai and Roman Byshko.
This adds support for the Allwinner sunxi musb controller in both host only
and otg mode. Peripheral only mode is not supported, as no boards use that.
This has been tested on a cubietruck (A20 SoC) and an UTOO P66 tablet
(A13 SoC) with a variety of devices in host mode and with the g_serial gadget
driver in peripheral mode, plugging otg / host cables in/out a lot of times
in all possible imaginable plug orders.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind(). Field 'can_activate' in struct f_obex is no longer
needed as setting 'bind_deactivated' flag makes us sure, that the function
will be binded only if deactivation can be performed successfully.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces 'bind_deactivated' flag in struct usb_function.
Functions which don't want to be activated automatically after bind should
set this flag, and when they start to be ready to work they should call
usb_function_activate().
When USB function sets 'bind_deactivated' flag, initial deactivation
counter is incremented automatically, so there is no need to call
usb_function_deactivate() in function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using usb_gadget_disconnect to make gadget temporarily invisible to host
doesn't provide desired result, because gadget is connected immediately
after binding regardless to previous usb_gadget_disconnect() calls.
For this reason we use usb_gadget_deactivate() instead of
usb_gadget_disconnect() to make it working as expected.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Driver handles PHY initialization, clock management, power
management and workarounds required after resetting the hardware.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass storage spec allows up to 16 LUNs, so let's not
add some more restrictive limits.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
EXPORT_SYMBOL_GPL() is usually placed after function definition
not before.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>