Commit graph

287,481 commits

Author SHA1 Message Date
Dave Gordon
2617268ff9 drm/i915: Add GuC-related header files
intel_guc_fwif.h contains the subset of the GuC interface that we
will need for submission of commands through the GuC. These MUST
be kept in sync with the definitions used by the GuC firmware, and
updates to this file will (or should) be autogenerated from the
source files used to build the firmware. Editing this file is
therefore not recommended.

i915_guc_reg.h contains definitions of GuC-related hardware:
registers, bitmasks, etc. These should match the BSpec.

v2:
    Files renamed & resliced per review comments by Chris Wilson

v4:
    Added DON'T-EDIT-ME warning [Tom O'Rourke]

Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-07-21 08:38:00 +02:00
Alex Dai
63dc04498a drm/i915: Add GuC-related module parameters
Two new module parameters: "enable_guc_submission" which will turn
on submission of batchbuffers via the GuC (when implemented), and
"guc_log_level" which controls the level of debugging logged by the
GuC and captured by the host.

Signed-off-by: Alex Dai <yu.dai@intel.com>

v4:
    Mark "enable_guc_submission" unsafe [Daniel Vetter]

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-07-21 08:37:35 +02:00
Dave Gordon
ea70299d6e drm/i915: Add i915_gem_object_create_from_data()
i915_gem_object_create_from_data() is a generic function to save data
from a plain linear buffer in a new pageable gem object that can later
be accessed by the CPU and/or GPU.

We will need this for the microcontroller firmware loading support code.

Derived from i915_gem_object_write(), originally by Alex Dai

v2:
    Change of function: now allocates & fills a new object, rather than
        writing to an existing object
    New name courtesy of Chris Wilson
    Explicit domain-setting and other improvements per review comments
        by Chris Wilson & Daniel Vetter

v4:
    Rebased

Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-07-21 08:36:12 +02:00
Lucas Stach
63caae8480 sched/idle: Move latency tracing stop/start calls deeper inside the idle loop
Make sure to stop tracing only once we are past a point where
all latency tracing events have been processed (irqs are not
enabled again). This has the slight advantage of capturing more
latency related events in the idle path, but most importantly it
makes sure that latency tracing doesn't get re-enabled
inadvertently when new events are coming in.

This makes the irqsoff latency tracer useful again, as we stop
capturing CPU sleep time as IRQ latency.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel@pengutronix.de
Cc: patchwork-lst@pengutronix.de
Link: http://lkml.kernel.org/r/1437410090-3747-1-git-send-email-l.stach@pengutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2015-07-21 08:18:51 +02:00
David S. Miller
f3120acc78 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-07-17

This series contains updates to igb, ixgbe, ixgbevf, i40e, bnx2x,
freescale, siena and dp83640.

Jacob provides several patches to clarify the intended way to implement
both SIOCSHWTSTAMP and ethtool's get_ts_info().  It is okay to support
the specific filters in SIOCSHWTSTAMP by upscaling them to the generic
filters.

Alex Duyck provides a igb patch to pull the time stamp from the fragment
before it gets added to the skb, to avoid a possible issue in which the
fragment can possibly be less than IGB_RX_HDR_LEN due to the time stamp
being pulled after the copybreak check.  Also provides a ixgbevf patch to
fold the ixgbevf_pull_tail() call into ixgbevf_add_rx_frag(), which gives
the advantage that the fragment does not have to be modified after it is
added to the skb.

Fan provides patches for ixgbe/ixgbevf to set the receive hash type
based on receive descriptor RSS type.

Todd provides a fix for igb where on check for link on any media other
than copper was not being detected since it was looking on the incorrect
PHY page (due to the page being used gets switched before the function
to check link gets executed).
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:50:19 -07:00
Florian Fainelli
28b45910cc net: bcmgenet: Remove init parameter from bcmgenet_mii_config
Now that we have reworked the way we perform the PHY initialization, we
no longer need to differentiate between init time vs. non-init time
calls, just use a dev_info_once() print to print the PHY type.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:48:14 -07:00
Florian Fainelli
6cc8e6d4dc net: bcmgenet: Delay PHY initialization to bcmgenet_open()
We are currently doing a full PHY initialization and even starting the
pHY state machine during bcmgenet_mii_init() which is executed in the
driver's probe function. This is convenient to determine whether we can
attach to a proper PHY device but comes at the expense of spending up to
10ms per MDIO transactions (to reach the waitqueue timeout), which slows
things down.

This also creates a sitaution where we end-up attaching twice to the
PHY, which is not quite correct either.

Fix this by moving bcmgenet_mii_probe() into bcmgenet_open() and update
its error path accordingly.

Avoid printing the message "attached PHY at address 1 [...]" every time
we bring up/down the interface and remove this print since it duplicates
what the PHY driver already does for us.

Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:48:14 -07:00
Florian Fainelli
c624f89121 net: bcmgenet: Determine PHY type before scanning MDIO bus
Our internal GPHY might be powered off before we attempt scanning the
MDIO bus and bind a driver to it. The way we are currently determining
whether a PHY is internal or not is done *after* we have successfully
matched its driver. If the PHY is powered down, it will not respond to
the MDIO bus, so we will not be able to bind a driver to it.

Our Device Tree for GENET interfaces specifies a "phy-mode" value:
"internal" which tells if this internal uses an internal PHY or not.

If of_get_phy_mode() fails to parse the 'phy-mode' property, do an
additional manual lookup, and if we find "internal" set the
corresponding internal variable accordingly.

Replace all uses of phy_is_internal() with a check against
priv->internal_phy to avoid having to rely on whether or not
priv->phydev is set correctly.

Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:48:14 -07:00
Florian Fainelli
bd4060a610 net: bcmgenet: Power on integrated GPHY in bcmgenet_power_up()
We are currently disabling the GPHY interface during bcmgenet_close(),
and attempting to power it back on during bcmgenet_open(). This works
fine for the first time, because we called bcmgenet_mii_config() which
took care of enabling the interface, however, bcmgenet_power_up() really
needs to power on the GPHY for correctness.

This will be particularly important as we want to move
bcmgenet_mii_probe() down to bcmgenet_open() to avoid seeing the "PHY
already attached" message.

Fixes: a642c4f790 ("net: bcmgenet: power up and down integrated GPHY when unused")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:48:14 -07:00
Florian Fainelli
978ffac418 net: bcmgenet: Use correct dev_id for free_irq
bcmgenet_open()'s error path call free_irq() with a dev_id argument
different from the one we used to call request_irq() with, this will
make us trip over the warning in kernel/irq/manage.c:__free_irq()

Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:48:14 -07:00
Florian Fainelli
6ac3ce8295 net: bcmgenet: Remove excessive PHY reset
We are currently issuing multiple PHY resets during a suspend/resume,
first during bcmgenet_power_up() which does a hardware reset, then a
software reset by calling bcmgenet_mii_reset(). This is both unnecessary
and can take as long as 10ms per MDIO transactions while we re-apply
workarounds because we do not yet have MDIO interrupts enabled.

phy_resume() takes care of re-apply our workarounds in case we need any,
and bcmgenet_power_up() does a PHY hardware reset, all of this is more
than enough to guarantee that the PHY operates correctly.

Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:48:14 -07:00
Joachim Eastwood
1734befd06 stmmac: add proper probe function to dwmac-meson
By using a few functions from stmmac_platform we can now create
a proper probe function in this driver. By doing so we can drop
the OF match data and simplify the overall driver.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:45:57 -07:00
Joachim Eastwood
f4f8dfdedf stmmac: add proper probe function to dwmac-lpc18xx
By using a few functions from stmmac_platform we can now create
a proper probe function in this driver. By doing so we can drop
the OF match data and simplify the overall driver.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:45:57 -07:00
Joachim Eastwood
402dae0bed stmmac: export probe_config_dt() and get_platform_resources()
Export stmmac_probe_config_dt() and stmmac_get_platform_resources()
so they can be used in the dwmac-* drivers themselves. This will
allow us to build more flexible and standalone drivers which just
use stmmac_platform as a library for setup functions.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:45:57 -07:00
Joachim Eastwood
b0003ead75 stmmac: make stmmac_probe_config_dt return the platform data struct
Since stmmac_probe_config_dt() allocates the platform data structure
it is cleaner if it just returned this structure directly. This
function will later be used in the probe function in dwmac-* drivers.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:45:56 -07:00
Joachim Eastwood
f396cb0121 stmmac: introduce stmmac_get_platform_resources()
Refactor all code that deals with platform resources into it's
own get function. This function will later be used in the probe
function in dwmac-* drivers.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:45:56 -07:00
Joachim Eastwood
4ed2d8fca7 stmmac: clean up platform/of_match data retrieval
Refactor code to clearly separate probing non-dt versus dt. In the
non-dt case platform data must be supplied to probe successfully.
For dt the platform data structure is created and match data is
copied into it. Note that support for supplying platform data in
dt from AUXDATA is dropped as no users in mainline does this.

This change will allow dt dwmac-* drivers to call the config_dt()
function from probe to create the needed platform data struct and
retrieve common dt properties.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:45:56 -07:00
Joachim Eastwood
0dacf3f664 stmmac: use of_device_get_match_data to retrieve of match data
By using of_device_get_match_data() the code that retrieve
match data can be simplified quite a bit.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:45:56 -07:00
Reinhard Speyerer
e3426ca7bc qmi_wwan: add the second QMI/network interface for Sierra Wireless MC7305/MC7355
Sierra Wireless MC7305/MC7355 with USB ID 1199:9041 also provide a
second QMI/network interface like the MC73xx with USB ID 1199:68c0 on
USB interface #10 when used in the appropriate USB configuration.
Add the corresponding QMI_FIXED_INTF entry to the qmi_wwan driver.

Please note that the second QMI/network interface is not working for
early MC73xx firmware versions like 01.08.x as the device does not
respond to QMI messages on the second /dev/cdc-wdm port.

Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:42:39 -07:00
Sergei Shtylyov
06613e38f1 ravb: fix race updating TCCR
The TCCR.TSRQn bit may get clearead after TCCR gets read, so that TCCR write
would get skipped. We don't need to check this bit before setting.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:42:02 -07:00
Karicheri, Muralidharan
194ac06e39 net: netcp: fix improper initialization in netcp_ndo_open()
The keystone qmss will raise interrupt when packet arrive at the
receive queue. Only control available to avoid interrupt from happening
is to keep the free descriptor queue (FDQ) empty in the receive side.
So the filling of descriptors into the FDQ has to happen after
request_irq() call is made as part of knav_queue_enable_notify(). So
move the function netcp_rxpool_refill() after this call.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:37:39 -07:00
dingtianhong
a951bc1e6b bonding: correct the MAC address for "follow" fail_over_mac policy
The "follow" fail_over_mac policy is useful for multiport devices that
either become confused or incur a performance penalty when multiple
ports are programmed with the same MAC address, but the same MAC
address still may happened by this steps for this policy:

1) echo +eth0 > /sys/class/net/bond0/bonding/slaves
   bond0 has the same mac address with eth0, it is MAC1.

2) echo +eth1 > /sys/class/net/bond0/bonding/slaves
   eth1 is backup, eth1 has MAC2.

3) ifconfig eth0 down
   eth1 became active slave, bond will swap MAC for eth0 and eth1,
   so eth1 has MAC1, and eth0 has MAC2.

4) ifconfig eth1 down
   there is no active slave, and eth1 still has MAC1, eth2 has MAC2.

5) ifconfig eth0 up
   the eth0 became active slave again, the bond set eth0 to MAC1.

Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same
MAC address, it will break this policy for ACTIVE_BACKUP mode.

This patch will fix this problem by finding the old active slave and
swap them MAC address before change active slave.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:29:40 -07:00
David S. Miller
686c953ea9 linux-can-fixes-for-4.2-20150716
-----BEGIN PGP SIGNATURE-----
 
 iQEcBAABCgAGBQJVp19MAAoJEP5prqPJtc/HsA8IAIqYKwJtXHItVoG6GBxLo/iJ
 G6OhCxSgDPUdytdyvWRmYL+2g6q9+BefnApwGroM0wowytHx4I6kF2O4LKEvthnD
 TzDV6uY0n1CR8FzCdfQdTFedAfxIx7DLCqY/iC+JRFTh6Vhvj46WtHickthu4Se+
 ygTWg5f5Da086JTUtwbb75TCHJv8xxtN57t6yZTtDoyaftqWd1Dzrmi8dBwHRWBA
 6X/rE4VekFwFCbqOlv5ghm86lD77sMTEaU0xkm9FeZmO/CnUD3JASwi844RtCqXR
 wj3OJ89qH14YmpJwjpakIwHfTyyPJurzPpPkCTZ6awmdNhCvp+h3nbfjKRqs0WU=
 =pQGs
 -----END PGP SIGNATURE-----

Merge tag 'linux-can-fixes-for-4.2-20150716' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2015-07-16

this is a pull request of 2 patches by Stefan Agner. He fixes the resume
operation in the mcp251x driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 20:25:59 -07:00
Scott Feldman
3f98a8e636 rocker: add offload_fwd_mark support
If device flags ingress packet as "fwd offload", mark the
skb->offlaod_fwd_mark using the ingress port's dev->offlaod_fwd_mark.  This
will be the hint to the kernel that this packet has already been forwarded
by device to egress ports matching skb->offlaod_fwd_mark.

For rocker, derive port dev->offlaod_fwd_mark based on device switch ID and
port ifindex.  If port is bridged, use the bridge ifindex rather than the
port ifindex.

Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 18:32:45 -07:00
Simon Horman
8254973fa3 rocker: forward packets to CPU when port is joined to openvswitch
Teach rocker to forward packets to CPU when a port is joined to Open vSwitch.
There is scope to later refine what is passed up as per Open vSwitch flows
on a port.

This does not change the behaviour of rocker ports that are
not joined to Open vSwitch.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 18:26:03 -07:00
Florian Fainelli
b8c6cd1d31 net: dsa: bcm_sf2: do not use indirect reads and writes for 7445E0
7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).

For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.

Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).

We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 16:47:30 -07:00
Nikolay Aleksandrov
7d5cd2ce52 bonding: correctly handle bonding type change on enslave failure
If the bond is enslaving a device with different type it will be setup
by it, but if after being setup the enslave fails the bond doesn't
switch back its type and also keeps pointers to foreign structures that can
be long gone. Thus revert back any type changes if the enslave failed and
the bond had to change its type.
Example:
 Before patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default
    link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
    link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
(notice the MASTER flag is gone)

 After patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
    link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
    link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff

Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: e36b9d16c6 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 16:23:06 -07:00
Viresh Kumar
4bc384ae62 cpufreq: propagate errors returned from __cpufreq_governor()
Return codes aren't honored properly in cpufreq_set_policy(). This can
lead to two problems:
- wrong errors propagated to sysfs
- we try to do next state-change even if the previous one failed

cpufreq_governor_dbs() now returns proper errors on all invalid
state-transition requests and this code should honor that.

Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-07-21 01:12:02 +02:00
Viresh Kumar
871ef3b53a cpufreq: governor: Don't WARN on invalid states
With previous commit, governors have started to return errors on invalid
state-transition requests. We already have a WARN for an invalid
state-transition request in cpufreq_governor_dbs(). This does trigger
today, as the sequence of events isn't guaranteed by cpufreq core.

Lets stop warning on that for now, and make sure we don't enter an
invalid state.

Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-07-21 01:12:02 +02:00
Viresh Kumar
a72c49590a cpufreq: governor: Avoid invalid states with additional checks
There can be races where the request has come to a wrong state. For
example INIT followed by STOP (instead of START) or START followed by
EXIT (instead of STOP).

Address these races by making sure the state-machine never gets into
any invalid state. Also return an error if an invalid state-transition
is requested.

Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-07-21 01:12:02 +02:00
Viresh Kumar
43e0ee361e cpufreq: governor: split out common part of {cs|od}_dbs_timer()
Some part of cs_dbs_timer() and od_dbs_timer() is exactly same and is
unnecessarily duplicated.

Create the real work-handler in cpufreq_governor.c and put the common
code in this routine (dbs_timer()).

Shouldn't make any functional change.

Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-07-21 01:12:01 +02:00
Viresh Kumar
44152cb82d cpufreq: governor: Keep single copy of information common to policy->cpus
Some information is common to all CPUs belonging to a policy, but are
kept on per-cpu basis. Lets keep that in another structure common to all
policy->cpus. That will make updates/reads to that less complex and less
error prone.

The memory for cpu_common_dbs_info is allocated/freed at INIT/EXIT, so
that it we don't reallocate it for STOP/START sequence. It will be also
be used (in next patch) while the governor is stopped and so must not be
freed that early.

Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-07-21 01:12:01 +02:00
Mathias Krause
8ce344c66e ACPI / processor: remove leftover __refdata annotations
The processor_handler structure does not reference any __init / __exit
code or data. Therefore the __refdata annotation is not needed. It used
to be prior to commit fe7bf106eb ("acpi: delete __cpuinit usage from
all acpi files") due to the __cpuinit annotation of acpi_processor_add().
But with that commit in place that requirement has gone.

The same is true for the acpi_cpu_notifier notifier block.
acpi_cpu_soft_notify() used to be marked __cpuinit but lost its
annotation in the above mentioned commit as well. Therefore the __refdata
annotation isn't needed there either.

Just drop the unneded __refdata annotations to be able to catch future
section mismatches.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-07-21 01:01:46 +02:00
Boris Brezillon
8c4b4b0d19 drm: atmel-hlcdc: fix vblank initial state
drm_vblank_on() now warns on nested use or if vblank is not properly
initialized. This patch fixes Atmel HLCDC vblank initial state.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
2015-07-20 22:47:11 +02:00
Greg Kroah-Hartman
ed15e8880f Merge 4.2-rc3 into staging-next
We need the staging fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-20 13:21:28 -07:00
Nikolay Aleksandrov
06f6d1094a bonding: fix destruction of bond with devices different from arphrd_ether
When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[  908.963051] eql: event: 9
[  908.963052] eql: IFF_SLAVE
[  908.963054] eql: event: 2
[  908.963056] eql: IFF_SLAVE
[  908.963058] eql: event: 6
[  908.963059] eql: IFF_SLAVE
[  908.963110] bond0: Releasing active interface eql
[  908.976168] bond0: Destroying bond bond0
[  908.976266] bond0 (unregistering): Released all slaves
[  908.984097] ------------[ cut here ]------------
[  908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[  908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[  908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]

[  908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G        W  O
4.2.0-rc2+ #8
[  908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[  908.984172]  0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[  908.984175]  ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[  908.984178]  ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[  908.984181] Call Trace:
[  908.984188]  [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[  908.984193]  [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[  908.984196]  [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[  908.984199]  [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[  908.984205]  [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[  908.984208]  [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[  908.984217]  [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[  908.984225]  [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[  908.984228]  [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[  908.984232]  [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[  908.984236]  [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[  908.984241]  [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[  908.984244]  [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[  908.984247] ---[ end trace 7c006ed4abbef24b ]---

Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f939981492 ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.

Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3dd ("bonding: Manage /proc/net/bonding/ entries from
                      the netdev events")
Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 12:56:11 -07:00
Nikolay Aleksandrov
22f94e6256 bonding: trivial: remove unused variables
Get rid of these:
drivers/net/bonding//bond_main.c: In function ‘bond_update_slave_arr’:
drivers/net/bonding//bond_main.c:3754:6: warning: variable
‘slaves_in_agg’ set but not used [-Wunused-but-set-variable]
  int slaves_in_agg;
      ^
  CC [M]  drivers/net/bonding//bond_3ad.o
drivers/net/bonding//bond_3ad.c: In function
‘ad_marker_response_received’:
drivers/net/bonding//bond_3ad.c:1870:61: warning: parameter ‘marker’
set but not used [-Wunused-but-set-parameter]
 static void ad_marker_response_received(struct bond_marker *marker,
                                                             ^
drivers/net/bonding//bond_3ad.c:1871:19: warning: parameter ‘port’ set
but not used [-Wunused-but-set-parameter]
      struct port *port)
                   ^

Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 12:50:32 -07:00
Vivien Didelot
40a7166044 net: dsa: mv88e6xxx: fix fid_mask when leaving bridge
The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.

This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.

Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).

Indeed, br0 uses FID 0, and br1 uses FID 3.

After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).

With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 12:44:14 -07:00
Michael S. Tsirkin
75993300d0 virtio_net: don't require ANY_LAYOUT with VERSION_1
ANY_LAYOUT is a compatibility feature. It's implied
for VERSION_1 devices, and non-transitional devices
might not offer it. Change code to behave accordingly.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 12:43:33 -07:00
Govindarajulu Varadarajan
d9382bda4e enic: allow adaptive coalesce setting for msi/legacy intr
* Allow setting of adaptive coalescing setting for all types of interrupt.

* In msi & legacy intr, we use single interrupt for rx & tx. In this case
  tx_coalesce_usecs is invalid. We should use only rx_coalesce_usecs.
  Do not display tx_coal values for msi/intx. And do not allow user to set
  this as well.

* Driver supports only tx/rx_coalesce_usec and adaptive coalesce settings.
  For other values, driver does not return error. So ethtool succeeds for
  unsupported values. Introduce enic_coalesce_valid() function to validate
  the coalescing values.

* If user requests for coalesce value greater than what adaptor supports,
  driver uses the max value. We should at least log this.

Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 12:39:34 -07:00
Govindarajulu Varadarajan
fc865d6b4a enic: add adaptive coalescing intr for intx and msi poll
Adaptive interrupt coalescing is available for msix. This patch adds the support
for msi poll. Interface for adaptive interrupt coalescing is already added in
driver. We just did not enable it for legacy intr & msi.

enic_calc_int_moderation() & enic_set_int_moderation() are defined as static
after enic_poll. Since enic_poll needs it, move both of these function
definitions above enic_poll. No change in functionality.

Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-20 12:39:34 -07:00
Stephen Boyd
6acc63b502 clk: h8300: Remove clk.h and clkdev.h includes
Neither of these includes are used in these files, remove them.

Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2015-07-20 11:11:41 -07:00
Stephen Boyd
6a8ce8c96c clk: at91: Include clk.h and slab.h
This clock provider uses the consumer API, so include clk.h
explicitly. Also include slab.h instead of relying on clkdev.h
for it.

Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2015-07-20 11:11:40 -07:00
Stephen Boyd
27df3ee278 clk: ti: Switch clk-provider.h include to clk.h
This file isn't a clock provider but uses the consumer API, so
include clk.h instead of clk-provider.h.

Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2015-07-20 11:11:38 -07:00
Stephen Boyd
cb58e14efb clk: pistachio: Include clk.h
This clock provider uses the consumer API, so include clk.h
explicitly.

Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2015-07-20 11:11:37 -07:00
Stephen Boyd
e2a657090a clk: ingenic: Include clk.h
This clock provider uses the consumer API, so include clk.h
explicitly.

Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2015-07-20 11:11:36 -07:00
Stephen Boyd
530b544ebf clk: si570: Include clk.h
This clock provider uses the consumer API, so include clk.h
explicitly.

Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2015-07-20 11:11:35 -07:00
Stephen Boyd
67bb5408a8 clk: moxart: Include clk.h
This clock provider uses the consumer API, so include clk.h
explicitly.

Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2015-07-20 11:11:33 -07:00
Stephen Boyd
a826a1a421 clk: cdce925: Include clk.h
This clock provider uses the consumer API, so include clk.h
explicitly.

Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2015-07-20 11:11:32 -07:00
Stephen Boyd
3c37311730 clk: Include clk.h in clk.c
This file implements the clk API and so it should include clk.h
directly instead of indirectly including it through
clk-provider.h.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
2015-07-20 11:11:30 -07:00