TI's opt3001 light sensor is a simple and yet powerful
little device. The device provides 99% IR rejection,
automatic full-scale, very low power consumption and
measurements from 0.01 to 83k lux.
This patch adds support for that device using the IIO
framework.
See http://www.ti.com/product/opt3001 for more information.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This cleans up the most ugly workaround in this driver. There are no
functional changes yet in the decoding algorithm, but we improve the
following things:
* Get rid of spurious warning messages on systems with fast HRTIMER.
* If the clock is not fast enough for decoding to work, we give
up immediately.
* In that case we return EAGAIN instead of EIO, so it's easier to
discriminate causes of failure.
Returning EAGAIN is somewhat controversial: It's technically correct
as a faster clock might become available. OTOH once all clocks are
enabled this is a permanent error. There is no ECLOCKTOOSLOW error
code.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* add spaces around binary operators in cases where it reduces readability
* align multiline statements around opening parenthesis
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
in Message-ID: <55919E72.3010807@gmx.de>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver currently does not take into account the minimum sample time
as per the Figure 6-8 Chapter 9.1.1 12-bit ADC electrical characteristics.
We set a static amount of cycles instead of considering the sample time
as a given value, which depends on hardware characteristics.
Determine sampling frequencies by first reading the device tree property
node and then calculating the required Long Sample Time Adder (LSTAdder)
value, based on the ADC clock frequency and sample time value obtained
from the device tree. This LSTAdder value is then used for calculating
the sampling frequencies possible.
In case the sample time property is not specified through the device
tree, a safe default value of 1000ns is assumed.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for Microchip's 13 bit 1 channel AD converter MCP3301
Signed-off-by: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There is a overshoot in DCDC1/DCDC2, we have 2 method to workaround:
1st is use dvs pin to switch the voltage between value in BUCKn_ON_VSEL
and BUCKn_DVS_VSEL. If DVS pin is inactive, the voltage of DCDC1/DCDC2
are controlled by BUCKn_ON_VSEL, when we pull dvs1/dvs2 pin to active,
they would be controlled by BUCKn_DVS_VSEL. In this case, the ramp rate
is same as the value programmed in BUCKn_RATE, and the fastest rate is
10mv/us.
2nd method is gradual adjustment, adjust the voltage to a target value
step by step via i2c, each step is set to 100 mA. If you write the
voltage directly using an i2c write the rk808 will always ramp as fast
as it possibly can, about 100mv/us.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
r852_ecc_correct() reads a 32-bit register into a 16-bit variable,
ecc_reg, but this variable is later used as if it was larger. This is
reported by clang when building the kernel with many warnings:
drivers/mtd/nand/r852.c:512:11: error: shift count >= width of type
[-Werror,-Wshift-count-overflow]
ecc_reg >>= 16;
^ ~~
Fix this by making ecc_reg 32-bit, like the return type of
r852_read_reg_dword().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVrBp0AAoJEHm+PkMAQRiGADsH/iCVjA1x+a19xpeuHNJcjcQR
Lin8td8zdUxereBNQOFjnkhCmKtzLODXGkQdYFaWZx8mbEQ93wC+nPV8O+LsqPbI
T/2MjJ78IjlNsoTyE4b1AhqpASsxrLZJNB+f9dd251f1BSAzKfRER0G46WxbOPN7
9HdzCMbtx03ZJkr9baE6alljxA43O5mpDzpotKIagfTMQr5h0ra16uXlmVXFjHRs
roNJsugwKxJPnVmLWWOM1JsAjRSMBAXQUQxhJJCMDOhgZZ5KR1z6L30ESeFTUhvh
WG/2MEfyVYXn91kV0N+AUCuOFHTv6uiaz3RaRVJFDSv3sPOh1WQ9tQHxyrBsqyY=
=MA/P
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc3' into next
Sync up with Linux 4.2-rc3 to bring in infrastructure (OF) pieces.
It is needed for k2l keystone2 EVM which uses NAND flash with 4K page
size, hence add support for 4K page size nand devices.
[Brian: similar work submitted by Murali Karicheri <m-karicheri2@ti.com>
and Hao Zhang <hzhang@ti.com>]
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ELAN0600 seems to work just fine in mouse emulation mode through i2c-hid,
but to have full raw touch support we need to register it in elan_i2c.ko
Reported-and-tested-by: Alessio Treglia <alessio@debian.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 2d53809594 ("Input: zforce_ts - convert to use the gpiod
interface") converted this driver to use the gpiod functions. These
functions take the active low property into account, so we don't have
to invert the result of gpiod_get_value_cansleep(). This has been
missed in that commit. Fix it.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We check the ATS state (enabled/disabled) and fetch the PCI ATS Invalidate
Queue Depth in performance-sensitive paths. It's easy to cache these,
which removes dependencies on PCI.
Remember the ATS enabled state. When enabling, read the queue depth once
and cache it in the device_domain_info struct. This is similar to what
amd_iommu.c does.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
This patch introduces a new compatible string: "atmel,sama5d3-rstc" and
new reset function for sama5d3 and later chips.
As in sama5d3 or later chips, we don't have to shutdown the DDR
controller before reset. Shutdown the DDR controller before reset is a
workaround to avoid DDR signal driving the bus, but since sama5d3 and
later chips there is no such a conflict.
So in this patch:
1. the sama5d3 reset function only need to write the rstc register
and return.
2. we can remove the code related with sama5d3 DDR controller as
we don't use it at all.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When dom0 is being ballooned balloon_process() will hold the balloon
mutex until it is finished. This will block e.g. creation of new
domains as the device backends for the new domain need some
autoballooned pages for the ring buffers.
Avoid this by releasing the balloon mutex from time to time during
ballooning. Adjust the comment above balloon_process() regarding
multiple instances of balloon_process().
Instead of open coding it, just use cond_resched().
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
oz_timer_add() modifies the expiry value of an active timer, which
results in data corruption.
Use hrtimer_start() and remove the silly conditional.
While at it use the proper helper function to convert milliseconds to
ktime.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Shigekatsu Tateno <shigekatsu.tateno@atmel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org
Link: http://lkml.kernel.org/r/20150413210035.357448657@linutronix.de
Tests with a Sierra Wireless MC7355 have shown that 1199:9041 devices
also require the option_send_setup() code to be used on the USB
interface for the AT port to make unsolicited response codes work
correctly. Move these devices from the qcserial driver to the option
driver like it has been done for the 1199:68c0 devices in commit
d80c0d1418 ("USB: qcserial/option: make
AT URCs work for Sierra Wireless MC73xx").
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The param_val variable is what determines if schmitt
trigger is enabled on a pin or not. A typo here mean
that schmitt trigger was always enabled for standard
and i2c pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
imx1_pinconf_set assumes that the array of pins in struct
imx1_pinctrl_soc_info can be indexed by pin id to get the
pinctrl_pin_desc for a pin. This used to be correct up to commit
607af165c0 which removed some entries from the array and so made it
wrong to access the array by pin id.
The result of this bug is a wrong pin name in the output for small pin
ids and an oops for the bigger ones.
This patch is the result of a discussion that includes patches by Markus
Pargmann and Chris Ruehl.
Fixes: 607af165c0 ("pinctrl: i.MX27: Remove nonexistent pad definitions")
Cc: stable@vger.kernel.org
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's possible to hit a race condition if interrupts are generated on a GPIO
pin when the IRQ line in question is being disabled.
If the interrupt is freed, bcm2835_gpio_irq_disable() is called which
disables the event generation sources (edge, level). If an event occurred
between the last disabling of hard IRQs and the write to the event
source registers, a bit would be set in the GPIO event detect register
(GPEDSn) which goes unacknowledged by bcm2835_gpio_irq_handler()
so Linux complains loudly.
There is no per-GPIO mask register, so when disabling GPIO interrupts
write 1 to the relevant bit in GPEDSn to clear out any stale events.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PFC driver causes the kernel to hang on the R-Car gen2 SoC based boards
when the CPU_ALL_PORT() macro is fixed to reflect the reality, i.e. when the
GPIO space becomes actually sparse. This happens because the _GP_GPIO() macro
includes an indexed initializer which causes the "holes" (array entries filled
with all 0s) between the groups of the existing GPIOs; and the driver can't
cope with that. There seems to be no reason to use the indexed initializer,
so we can remove the index specifier and so avoid the "holes".
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a21763a0b1
"pinctrl: nomadik: activate strict mux mode"
put all Nomadik pin controllers to strict mode. This was
not good on the Snowball platform: the muxing of GPIOs to
different pins is done with hogs in the DTS file, and then
these GPIOs are used by offset, relying on hogs to mux the
pins. Since that means the pin controller "owns" the pins
and at the same time we have a GPIO user, this pin controller
is by definition not strict.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 6adfb1ef10.
Ironlake RPS code runs under an irqsave spinlock and hence sleeping
isn't allowed. Not a this long delay while blocking irqs isn't great
at all, but fixing the locking scheme is a lot more involved.
So just revert for now.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: kernel test robot <ying.huang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Add support for the Security System included in Allwinner SoC A20.
The Security System is a hardware cryptographic accelerator that support:
- MD5 and SHA1 hash algorithms
- AES block cipher in CBC/ECB mode with 128/196/256bits keys.
- DES and 3DES block cipher in CBC/ECB mode
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
An implicit truncation is done when using a variable of 64 bits
in MATH command:
warning: large integer implicitly truncated to unsigned type [-Woverflow]
Silence the compiler by feeding it with an explicit truncated value.
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When successful, the descriptor that performs RNG initialization
is allowed to return a status code of 7000_0000h, since last command
in the descriptor is a JUMP HALT.
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HW coherency won't work properly for CAAM write transactions
if AWCACHE is left to default (POR) value - 4'b0001.
It has to be programmed to 4'b0010, i.e. AXI3 Cacheable bit set.
For platforms that have HW coherency support:
-PPC-based: the update has no effect; CAAM coherency already works
due to the IOMMU (PAMU) driver setting the correct memory coherency
attributes
-ARM-based: the update fixes cache coherency issues,
since IOMMU (SMMU) driver is not programmed to behave similar to PAMU
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In order to ensure that the ERA property is properly read from DT
on all platforms, of_property_read* function needs to be used.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the pwm_get_xxx() helpers instead of directly accessing the fields
in struct pwm_device. This will allow us to smoothly move to the atomic
update approach.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Some PWM drivers are testing the PWMF_ENABLED flag. Create a helper
function to hide the logic behind enabled test. This will allow us to
smoothly move from the current approach to an atomic PWM update
approach.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch makes use of the new amd headers (that are part of the new
amdgpu driver), instead of private defines.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The MAP_QUEUES packet length for Carrizo is different than for Kaveri.
Therefore, we now need to calculate the runlist length with regard to the
underlying H/W.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch adds support for the VI APU in the DQM module.
Most of the functionality of DQM is shared between CI and VI. Therefore,
only a handful of functions are required to be in the
H/W-specific part of DQM.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch implements all the VI MQD manager functions.
This is done in a different file as the MQD format is different
between CI and VI
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch adds the PCI IDs of supported CZ devices to the
supported_devices structure in amdkfd. That structure is used during the
amdkfd probing stage, to check if the currently probed device is eligible
to be handled by amdkfd.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch adds the gfx8 interface file between amdgpu and amdkfd. This
interface file is currently in use when running on a Carrizo-based
system.
The interface itself is represented by a pointer to struct
kfd_dev. The pointer is located inside amdgpu_device structure.
All the register accesses that amdkfd need are done using this
interface. This allows us to avoid direct register accesses in
amdkfd proper, while also allows us to avoid locking between
amdkfd and amdgpu.
The single exception is the doorbells that are used in both of
the drivers. However, because they are located in separate pci
bar pages, the danger of sharing registers between the drivers
is minimal.
Having said that, we are planning to move the doorbells as well
to amdgpu.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch adds the gfx7 interface file between amdgpu and amdkfd. This
interface file mirrors (some) of the functions in radeon_kfd.c
(the interface file between radeon and amdkfd).
The gfx7 interface is used when it is run on a Kaveri-based system.
This interface file was used for bring-up of amdkfd on amdgpu and for
debugging purposes. For users who would like to run HSA on Kaveri, please
use the radeon graphic driver.
Note: CONFIG_DRM_AMDGPU_CIK must be selected for amdgpu to handle Kaveri.
v2: removed MTYPE_NONCACHED enum definition as it is defined in another
patch
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch adds an interface file between amdgpu and amdkfd. This
interface file is H/W agnostic, thus containing functions that
operate the same for any AMD APU/GPU H/W generation.
The functions in this interface mirror (some) of the functions in
radeon_kfd.c (the radeon<-->amdkfd interface file). The main functions
are:
- amdgpu_amdkfd_init - initialize the amdkfd module
- amdgpu_amdkfd_load_interface - load the H/W interface according to the
currently probed device
- amdgpu_amdkfd_device_probe - probe the device in amdkfd
- amdgpu_amdkfd_device_init - initialize the device in amdkfd
- amdgpu_amdkfd_interrupt - call the ISR of amdkfd
- amdgpu_amdkfd_suspend - suspend callback from amdgpu
- amdgpu_amdkfd_resume - resume callback from amdgpu
This patch also modifies the relevant amdgpu files, to use this new
interface.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This patch splits the KGD_ENGINE_SDMA to KGD_ENGINE_SDMA1 and
KGD_ENGINE_SDMA2 to match CZ definitions.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>