Make selection between ULPI and UTMI+ interfaces possible by
providing definition for the bit in Global USB2 PHY
Configuration Register that controls it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Definitions for Global USB2 PHY Vendor Control Register
bits. We will need them to access ULPI PHY registers later.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UTMI+ Low Pin Interface (ULPI) is a commonly used PHY
interface for USB 2.0. The ULPI specification describes a
standard set of registers which the vendors can extend for
their specific needs. ULPI PHYs provide often functions
such as charger detection and ADP sensing and probing.
There are two major issues that the bus type is meant to
tackle:
Firstly, ULPI registers are accessed from the controller.
The bus provides convenient method for the controller
drivers to share that access with the actual PHY drivers.
Secondly, there are already platforms that assume ULPI PHYs
are runtime detected, such as many Intel Baytrail based
platforms. They do not provide any kind of hardware
description for the ULPI PHYs like separate ACPI device
object that could be used to enumerate a device from.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit db62b9a804 (usb: dwc2: host: don't
use dma_alloc_coherent with irqs disabled)
introduced a build warning by using NULL
as an integer. Fix that by just using 0 instead
of NULL.
Signed-off-by: Felipe Balbi <balbi@ti.com>
And let driver convert it to host-byte order as needed.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hrtimer_start() will no longer defer already expired timers to the
softirq in 4.2, and the __hrtimer_start_range_ns() function is
getting removed, causing build errors when both the tip tree and
the arm-ccn changes are merged.
This changes the code back to using hrtimer_start, which will
do the right thing after this branch gets merged with the
timers update from tip.
As pointed out after a discussion on the mailing list, the result will
not be worse than the what was there before you pulled my updates, as
the code was using normal hrtimer_start(). It's just when I realised
that it should be pinned I looked at what x86 uncore pmu is doing and
shamelessly (and probably a bit mindlessly) copied the "do not wakeup"
version from there.
[arnd: update commit message]
Reported-by: Mark Brown <mark.brown@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A couple of changes to the core SoC support code. Perhaps the most
important part is a fix for a regression in LP1 suspend/resume code that
was introduced a while back.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BR2n
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
Merge "ARM: tegra: Core SoC changes for v4.2-rc1" from Thierry Reding:
A couple of changes to the core SoC support code. Perhaps the most
important part is a fix for a regression in LP1 suspend/resume code that
was introduced a while back.
* tag 'tegra-for-4.2-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: move to using a restart handler
ARM: tegra20: Store CPU "resettable" status in IRAM
soc/tegra: Watch wait_for_completion_timeout() return type
The RAM code is used by the memory and external memory controllers to
determine which set of timings to use for memory frequency scaling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yv05
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-ramcode' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "ARM: tegra: RAM code access for v4.2-rc1" from Thierry Reding:
The RAM code is used by the memory and external memory controllers to
determine which set of timings to use for memory frequency scaling.
* tag 'tegra-for-4.2-ramcode' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Add RAM code reader helper
of: Document long-ram-code property in nvidia,tegra20-apbmisc
Adds support for Tegra132 (which is mostly the same as for Tegra124,
except for cache maintenance). debugfs support is also introduced for
the SMMU part of the memory controller, which allows users to inspect
the translation state for SWGROUPs and memory clients.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJVU1AnAAoJEN0jrNd/PrOhWI8P/jqbjvaCbsbVciS4myB8xYhP
A4pny5L38xmz6ngKliBEfW10nwq2JsH+dKAlXzRYMej4QghKjVrVzY2AtYQ3v5wv
MeUx+yJTA54PxRHnI+dAiD7ak8ZswKsFADSVxbbOVHmI+4LQ9PAryW1lhQqikP+8
FzVXWzNrCh1Ikv9qiOYimbKycCYVwzf1cpOnaYgDt+WRfCZBYRaVP2KdTblgC8yu
BM2FiPoWUKdB+YCMYJB7qJtfZOe+lF6lUA8nUVaydnW3F9ll+fCnG/Ypk1iRkXr7
rrAW6IIvkvlLpxb4o27QkuSZYNEvjwbpNAfYEocZ7v/bLAa1Knwjj3MUItgE6MFp
zZuZ0bJ135DvGvNmkPpq3bK8c+iDsqqW2XjmHY6DCSDS9rYzyvu9b37XOYsV9HVr
iMY3Zd8gjrtzMwiE3xLaGxaz20osuWLU4JbOHHRVpgf2u5AWGEfN/kdO+ZJlerFG
7Z3t8svJaGaHB0EICvRxx/1dcnyW/FAS/7GC2Pb3afHBlqmxXdHa6cGzpbFlmEfz
miYgVlEZziJXL+MsUPNHUoupSe9jo/oxm8YOIXR7z9pI9Xg2OWOxhv0afG+i1Y/a
AniEnEmeon+wmL0699bDCvvtEEyRW+k2/mT9xp/M9Nr48DLRHYRVuiNYXd/wAk1t
xu63NH9f+I/4pMb1H+Za
=86m4
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.2-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "ARM: tegra: Memory controller updates for v4.2-rc1" from Thierry Reding:
Adds support for Tegra132 (which is mostly the same as for Tegra124,
except for cache maintenance). debugfs support is also introduced for
the SMMU part of the memory controller, which allows users to inspect
the translation state for SWGROUPs and memory clients.
* tag 'tegra-for-4.2-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: tegra: Disable ARBITRATION_EMEM interrupt
memory: tegra: Add Tegra132 support
iommu/tegra-smmu: Add debugfs support
memory: tegra: Add SWGROUP names
Now that the axp20x-regulators driver supports different variants of the
AXP family, we can enable regulator support for AXP22X without the risk
of incorrectly configuring regulators.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add AXP22X regulator definitions and variant id associations.
This introduces a new "switch" type output for one of the regulators.
It is a switchable secondary output of one regulator, with the same
voltage level as the primary output.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: Moved variant choosing to multi family support patch]
[wens@csie.org: Add dc-dc work frequency range]
[wens@csie.org: Add "switch" type output regulator DC1SW]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rework the AXP20X_ macros and probe function to support the several chip
families, so that each family can define it's own set of regulators.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: Support different DC-DC work frequency ranges]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the AXP22x PMIC devices to the existing AXP20x driver.
This includes the AXP221 and AXP223, which are identical except for
the external data bus. Only AXP221 is added for now. AXP223 will be
added after it's Reduced Serial Bus (RSB) interface is supported.
AXP22x defines a new set of registers, power supplies and regulators,
but most of the API is similar to the AXP20x ones.
A new irq chip definition is used, even though the available interrupts
on AXP22x is a subset of those on AXP20x. This is done so the interrupt
numbers match those on the datasheet.
This patch only enables the interrupts, system power-off function, and PEK
sub-device. The regulator driver must first support different variants
before we enable it from the mfd driver.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: fix interrupts and move regulators to separate patch]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If userspace asks for an INQUIRY buffer smaller than 36 bytes, the SCSI
translation layer will happily write past the end of the INQUIRY buffer
allocation.
This is fairly easily reproducible by running the libiscsi test
suite and then starting an xfstests run.
Fixes: 4f1982 ("NVMe: Update SCSI Inquiry VPD 83h translation")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The HDA to codec clock is named hda2codec_2x, so use the proper name in
the clock table.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC clock driver uses symbols exported by the EMC driver, so it
needs the corresponding dependency to avoid build breakage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
As opposed to round_rate(), determine_rate() can take rate constraints
into account when choosing the best rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra124, as we now have a proper driver for the EMC.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver is currently only tested on Tegra124 Jetson TK1, but should
work with other Tegra124 boards, provided that correct EMC tables are
provided through the device tree. Older chip models have differing
timing change sequences, so they are not currently supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
[treding@nvidia.com: use more consistent function names]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock has never been able to do anything.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To be used by clock implementations for switching to a new parent during
rate change.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of implement its own hexdump logic, use the printk
format, and convert to use pr_info().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename the macros to input_dbg() and ir_dbg(), using pr_fmt()
on both, to be coherent with the other debug macro changes.
The ir_dbg() also prints the IR name.
I'm not sure if it is a good idea to keep both macros here,
but merging them would require tests on different flavors of
saaa7134-based boards.
So, for now, let's keep both.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rename the macro to vbi_dbg()/video_dbg() and use pr_fmt(),
to be coherent with the other debug macro changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
instead of using dev->name, let's use pr_fmt() like on the
other parts of saa7134. Also, rename the debug macro to
ts_dbg() to match the namespace for the debug macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Converting debug prints to use pr_foo() is not trivial, as the
result will be a way worse than what's provided here, due to the
pieces of the code that prints the I2C transfers. Those use a
lot pr_cont(), and, depending on using either level 1 or 2,
a different set of macros are selected.
So, let's replace d1printk() and d2printk() macros by i2c_dbg()
and i2c_count() adding a debug level there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On media drivers, debugging messages should be grouped into
categories, as this makes easier to debug the driver.
In the case of saa7134, the core has 2 debug categories, one
for IRQ, and another one for the core itself. The IRQ have
actually 2 levels of debug.
So, instead of using pr_dbg(), where everything would be in
the same box, let's define two macros that use pr_fmt(),
one for the core, and another one for irq.
With that, we can replace the remaining printk() occurrences
at the core to use either core_dbg() or irq_dbg(), depending
on the group of debug macros that need to be enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On a few places, mostly during board detection, some printk()
macros were called without especifying any message level.
Those are actually warnings. So, use pr_warn() for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As this module doesn't use any debug level, it is easy to
just replace all debug printks by pr_debug().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As this module doesn't use any debug level, it is easy to
just replace all debug printks by pr_debug().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On saa7134-alsa, there is just one printk macro that use a
different debug level.
It should be easy to enable/disable this one using dynamic_printk,
if one need to individually control it.
So, this module can easily use pr_debug() instead of using its
own macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On a few places, the search expression used on the script that
replaced pr_info/pr_warn didn't match, because the string were
on the next line.
It is best to manually edit those lines, and re-indent the
paragraphs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replaces all occurrences of printk with KERN_INFO, KERN_WARNING
and KERN_ERR to pr_info/pr_warning, pr_err, using this small
shell script:
for i in drivers/media/pci/saa7134/*.[ch]; do sed s,'printk(KERN_INFO ','pr_info(',g <$i >a && mv a $i; done
for i in drivers/media/pci/saa7134/*.[ch]; do sed s,'printk(KERN_ERR ','pr_err(',g <$i >a && mv a $i; done
for i in drivers/media/pci/saa7134/*.[ch]; do sed s,'printk(KERN_WARNING ','pr_warn(',g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a pr_fmt macro, and move saa7134.h header to the beginning,
to avoid warnings when using the pr_foo macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Like other KVM switches, the Aten DVI KVM switch needs a quirk to avoid spewing
errors:
[791759.606542] usb 1-5.4: input irq status -75 received
[791759.614537] usb 1-5.4: input irq status -75 received
[791759.622542] usb 1-5.4: input irq status -75 received
Add it.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a regulator is listed in devicetree, but the node is marked as
"disabled" we should skip parsing the regulator init data and
deny consumers from interacting with the regulator. This
simplifies devicetree maintenance where we can have one dtsi file
with all regulators supported by a PMIC and then select what
regulators are used depending on the board configuration.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up chained handler and handler data if they were set by
gpiochip_set_chained_irqchip().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are cases where we want to test if a given object is
part of the state, but don't want to add them if they're not.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This results in a warning when building out of tree:
"cc1: warning: include/drm: No such file or directory [enabled by default]"
Most code already uses #include <drm/foo.h> correctly, so fix the
instances that don't.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This results in a warning when building out of tree:
"cc1: warning: include/drm: No such file or directory [enabled by default]"
Most code already uses #include <drm/foo.h> correctly, so fix the
instances that don't.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is useful for drivers which have their own modeset infrastructure
but want to reuse most of the legacy state frobbery from the helpers.
i915 wants this.
v2: Add header declaration.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The atomic helpers don't call drm_calc_timestamping_constants, which
is a regression compared to the crtc helpers. Fix this.
Noticed while reviewing i915 atomic patches from Maarten.
v2: Also check state->enable to avoid a warning in dmesg. Reported by
Maarten.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Add reference counting on a kernel module that exports dma-buf and
implements its operations. This prevents the module from being unloaded
while DMABUF file is in use.
The original patch [1] was submitted by Tomasz Stanislawski, but this
is a simpler way to do it.
v3: call module_put() as late as possible, per gregkh's comment.
v2: move owner to struct dma_buf, and use DEFINE_DMA_BUF_EXPORT_INFO
macro to simplify the change.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
[1]: https://lkml.org/lkml/2012/8/8/163
The irq chip functions use the irq chipdata directly as the base register
address of the controller, so this should be passed in instead of a pointer
to the array address holding the base address.
This fixes Tegra20 CPUidle as now the un-/masking of IRQs at the LIC level
works again, but more importantly it fixes the resulting memory corruption.
Fixes: de3ce08049 ' irqchip: tegra: Add DT-based support for legacy interrupt controller'
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1431202014-3136-1-git-send-email-dev@lynxeye.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Following what DT already does. If the device does not have ACPI Interrupt
resource but instead it has one or more GpioInt resources listed below it,
we take the first GpioInt resource, convert it to suitable Linux IRQ number
and pass it to the driver instead.
This makes drivers simpler because the don't need to care about GPIOs at
all if only thing they need is interrupt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the convention used in most parts of the kernel including DT
counterpart of I2C slave enumeration. To make things consistent do the same
for ACPI I2C slave enumeration path as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>