commit af3a4a9bbe ("[media] dib0700: NEC scancode cleanup") cleaned
up the NEC scancode logic but overlooked the RC5 case.
This patch brings the RC5 case in line with the NEC code and makes
the struct self-documenting.
Signed-off-by: David Härdeman <david@hardeman.nu>
Reported-by: David Cimbůrek <david.cimburek@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add 2 clocks which were erronously forgotten by the clock framework
port, namely :
- sa1100-rtc
- irda for pxa2xx-ir:UARTCLK
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Michael Turquette <mturquette@linaro.org>
Since pxa clocks were ported to the clock framework, an ordering issue
appears between clocks and clocksource initialization. As a consequence,
the pxa timer clock cannot be acquired in pxa_timer, and is disabled by
clock framework because it is "unused".
The ordering issue is that in the kernel boot sequence :
start_kernel()
...
time_init()
-> pxa_timer()
-> here the clocksource is initialized
...
rest_init()
kernel_init()
initcalls
-> here the clocks are initialized
In the current sequence, the clocks are initialized way after pxa_timer,
which cannot acquire the OSTIMER0 clock.
To solve this issue, the clocks initialization is moved to pxa_timer(),
so that clocks are initialized before clocksource for non device-tree.
For device-tree, the standard arm time_init() will take care of the
ordering.
Reviewed-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These KERN_<LEVEL> uses are unnecessary with pr_<level> and cause
bad logging output so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
GPIO chip select patch series appears to have broken the native chip select
support. This patch pulls the manual native chip select toggling out of
the transfer_one routine and adds a set_cs routine.
Tested natively on AM3354 with SPI serial flash on spi0cs0.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Michael Welling <mwelling@ieee.org>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
implement bus recovery methods for i2c-omap
so we can recover from situations where SCL/SDA
are stuck low.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
'channels' is allocated via kmemdup and it is never freed.
Use 'indio_dev->channels' directly instead, so that we avoid such
memory leak problem.
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to hardware team there should be some delay after
setting channel number, start mode and before setting START.
Add a one microsecond delay for this purpose.
Fixes: 1664f6a5b0 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
regulator_get_voltage() returns a non-negative value in case of success,
and a negative error in case of error. Let's fix this.
Fixes: 1664f6a5b0 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
At present we are incorrectly setting the register to 0x1 to power up
the ADC. Since it is an active high power down register, we need to set
the register to 0x0 to actually power up. Conversely, writing 0x1 to the
register powers it down.
This commit adds a couple of helpers to make the code clearer and then
use them to do the power-up/power-down properly.
Fixes: 1664f6a5b0 ("iio: adc: Cosmic Circuits 10001 ADC driver")
Signed-off-by: Naidu Tellapati <naidu.tellapati@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On A MIPS 32-cores machine a BUG_ON was triggered because some acesses to
mtd->usecount were done without taking mtd_table_mutex.
kernel: Call Trace:
kernel: [<ffffffff80401818>] __put_mtd_device+0x20/0x50
kernel: [<ffffffff804086f4>] blktrans_release+0x8c/0xd8
kernel: [<ffffffff802577e0>] __blkdev_put+0x1a8/0x200
kernel: [<ffffffff802579a4>] blkdev_close+0x1c/0x30
kernel: [<ffffffff8022006c>] __fput+0xac/0x250
kernel: [<ffffffff80171208>] task_work_run+0xd8/0x120
kernel: [<ffffffff8012c23c>] work_notifysig+0x10/0x18
kernel:
kernel:
Code: 2442ffff ac8202d8 000217fe <00020336> dc820128 10400003
00000000 0040f809 00000000
kernel: ---[ end trace 080fbb4579b47a73 ]---
Fixed by taking the mutex in blktrans_open and blktrans_release.
Note that this locking is already suggested in
include/linux/mtd/blktrans.h:
struct mtd_blktrans_ops {
...
/* Called with mtd_table_mutex held; no race with add/remove */
int (*open)(struct mtd_blktrans_dev *dev);
void (*release)(struct mtd_blktrans_dev *dev);
...
};
But we weren't following it.
Originally reported by (and patched by) Zhang and Giuseppe,
independently. Improved and rewritten.
Cc: stable@vger.kernel.org
Reported-by: Zhang Xingcai <zhangxingcai@huawei.com>
Reported-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com>
Tested-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit d4988623cc ("IB/qib: use arch_phys_wc_add()")
adjusted mtrr inititialization to use the new interface.
Unfortunately, the new interface returns a signed
value and the patch tested the unsigned wc_cookie.
Fix the issue by changing the type of wc_cookie to int. For
the success case the ret left at zero to avoid
a warning from the caller. For failure wc_cookie
is used as the ret.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These attributes should be exposed for the matching connector types
only, so checking is redundant.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The show methods for the attributes of DVI-I and TV-out types have a
bunch of code to deal with the differences between the two. Just split
the attributes into connector type specific ones. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split DVI-I and TV-out (which remains a group of types). As an
intermediate step, still share the attributes themselves between the
two. No user visible changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reduces duplication in the patches to follow. No functional
changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we're adding CEA modes after the inferred modes, which means
we might get multiple modes that are very close to each other, but
slightly different, which seems a bit silly. That's because duplicate
mode check that occurs when adding inferred modes would not consider
CEA modes as potential duplicates. Reverse the order so that CEA
modes get added before inferred modes, and are thus considered potential
duplicates.
Or as ajax put it on irc:
"< ajax> the point of the "pick a timing formula" heuristic was to
generate something the sink could _likely_ sink. if it tells us
timings it can sink explicitly then second-guessing seems dumb."
Cc: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The string iwpm_ulib_name is recorded in a nlmsg as a netlink attribute.
Without this fix parsing of the nlmsg by the userspace port mapper service fails
because of unknown attribute length, causing the port mapper service not to
register the client, which has sent the nlmsg.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Cc: <stable@vger.kernel.org> #v3.16
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This driver does not use any PCI IDs, don't include
the pci_ids.h header.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platform_device_id is not modified by these drivers and core uses it
as const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of error, the function platform_device_register_data() returns
ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 307e95c922 ("[media] mn88472: implement firmware parity check")
introduced the usage of exit paths that do not free the already allocated
firmware data in case the parity handling fails. Go through the correct
exit paths. Detected by Coverity CID 1295989.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GoTView MasterHD 3 is a DVB-T2/C USB 2.0 tuner.
It's based on the following components:
- USB bridge: RTL2832P (contains also DVB-T demodulator)
- Demodulator: Si2168-A30
- Tuner: Si2148-A20
The demodulator and the tuner will need firmwares. The Si2148 uses Si2158
firmware. Antti has the firmwares available for download:
http://palosaari.fi/linux/v4l-dvb/firmware/
Do note that for DVB-T either of the demodulators can be used. DVB-C and
DVB-T2 are only supported by the Si2168 demodulator. The driver will
register 2 frontends for the same adapter. Frontend 0 will be the RTL2832
demodulator and frontend 1 will be the Si2168 demodulator. The same
tuner is used for both.
As a consequence of the above, it's recommended to use application that
does implement proper DVBv5 support.
For some reason, the old I2C write method sporadically fails. Thus the
need for an option to only use the new I2C write method supported by the
RTL2832.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for I2C read operation without a preceeding write.
While here, change the error code to EOPNOTSUPP in case an
unsupported I2C operation is attempted.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The chips supported by the si2157 driver have two IF outputs (either
pins 12+13 or pins 9+11). Instead of hardcoding the output to be used
add an option to choose which output shall be used.
As this patch changes the default behaviour, the IF interface is
specified in each driver currently using si2157 driver. This is to
keep bisectability.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return error from si2168_cmd_execute in case the demodulator returns an
error.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change the dvbsky driver to support gapped clock instead of the current
hack.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a parameter in si2168_config to support gapped clock. This might be
necessary on some devices with higher bitrates.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Initialize sysreg by default, otherwise driver will crash in suspend
callback when not using DT.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: a7750c3ef0 ("i2c: s3c2410: Handle i2c sys_cfg register in i2c driver")
Make the modalias match driver name, this is required to make module
auto-loading work.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This adds calls to pinctrl subsystem in order to switch pin states
on suspend/resume if you provide a "sleep" state in DT.
If no "sleep" state is provided in the DT, these calls turn
to NOPs, so we don't need error checking here.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to the technical update (No. TN-RCS-B011A/E), the UGSTS LOCK
bit location is bit 8, not bits 1 and 0. It also says that the register
address offset of UGSTS is 0x88, not 0x90.
So, this patch fixes the USBHS_UGSTS_LOCK value and some comments.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
if devm_clk_get for wkupclk fails, there will be an unbalanced
pm_runtime_enable. Fix it here.
Reported-by: Benoit Parrot <bparrot@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
DM816x PHY uses usb_phy_* methods and because
of that, it must select USB_PHY, however, because
the drivers in question (DM816x, TWL4030 and
OMAP_USB2) sit outside of drivers/usb/ directory,
meaning they can be built even if USB_SUPPORT=n.
This patches fixes the dependencies by adding
USB_SUPPORT as a dependency and making all drivers
select USB_PHY (which cannot be selected through
menuconfig).
Note that this fixes some linking breakages when
building with randconfig.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This phy only exists on platforms under ARCH_QCOM, not ARCH_MSM.
Cc: Yaniv Gardi <ygardi@codeaurora.org>
Cc: Dov Levenglick <dovl@codeaurora.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- fixed a nasty bitfield mangling bug
- added new hints to the perf userspace tool
- pinned events processing to a single PMU
- modified events initialisation so they can be rotated now
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVQ7fuAAoJEL9jRaJfXa5Pr6EH+wd92YXgpFHy4x0O77GdK/gk
ErzfFlq/3GX6V+1WkMn0Nfj1vhl/Mq9RF4nSbmEU4c5x0ov48J67b94peo9RChfF
+BjaLw0mNijpCvcFYNIOW4qvJr5LKizvaq3uzw7h7AFl24MwRIKrNXJP6qON04sB
9TCekVCWutKORkEmVpl4Wltsb3LpqNwo/ziby2dmgRCsxPeXnOycsk45/4Tc0GSg
oR5MXLAuvxvNivNMF83FphiAeqPu1eeSWYkT468qqarr4NWKpbYd6uNTMViVHUcW
Yd6pxUwB7dphmLckDOIuJ9QJOfxL263uHaq1taUm1HVp15ldKfWapgVH4hIsUj8=
=mXhn
-----END PGP SIGNATURE-----
Merge tag 'ccn/updates-for-4.2' of git://git.linaro.org/people/pawel.moll/linux into next/drivers
Pull "Set of ARM CCN PMU driver updates" from Pawel Moll:
- fixed a nasty bitfield mangling bug
- added new hints to the perf userspace tool
- pinned events processing to a single PMU
- modified events initialisation so they can be rotated now
* tag 'ccn/updates-for-4.2' of git://git.linaro.org/people/pawel.moll/linux:
bus: arm-ccn: Allocate event when it is being added, not initialised
bus: arm-ccn: Do not group CCN events with other PMUs
bus: arm-ccn: Provide required event arguments
bus: arm-ccn: cpumask attribute
bus: arm-ccn: Fix node->XP config conversion
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates igb so that it will correctly perform the descriptor
count calculation. Previously it was taking NETDEV_FRAG_PAGE_MAX_SIZE
into account with isn't really correct since a different value is used to
determine the size of the pages used for TCP. That is actually determined
by SKB_FRAG_PAGE_ORDER.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once there were kernel drivers for some of the phidgets devices, and for
those kernel drivers to work the hid system needed exceptions. Now the
kernel drivers are long gone in favour of the user-space drivers.
The user-space drivers support many more phidget devices and uses libusb.
The udev rules set up permissions so that the kernel hid driver can be
unbound from libusb, as it does for many devices not in hid_ignore_list.
http://www.phidgets.com/docs/OS_-_Linux
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
info(drivers/i2c/busses/i2c-xiic.c:55): Scanning doc for struct xiic_i2c
Warning(drivers/i2c/busses/i2c-xiic.c:79): No description found for parameter 'endianness'
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although unlikely, it is remotely possible for an i2c command to need
more than 200ms complete. Unlike smbus, i2c devices can clock stretch
for an unspecified amount of time. The longest time I've seen
specified for a device is 144ms (bq27541 battery gas), but one could
imagine a device taking a bit slower. 1 second "ought to be enough for
anyone."
The above is not the only justifcation for going above 200ms for a
timeout, though. It turns out that if you've got a large number of
printks going out to a serial console, interrupts on a CPU can be
disabled for hundreds of milliseconds. That's not a great situation to
be in to start with (maybe we should put a cap in vprintk_emit()) but
it's pretty annoying to start seeing unexplained i2c timeouts.
Note that to understand why we can timeout when printk has interrupts
disabled, you need to understand that on current Linux ARM kernels
interrupts are routed to a single CPU in a multicore system. Thus,
you can get:
1. CPU1 is running rk3x_i2c_xfer()
2. CPU0 calls vprintk_emit(), which disables all IRQs on CPU0.
3. I2C interrupt is ready but is set to only run on CPU0, where IRQs
are disabled.
4. CPU1 timeout expires. I2C interrupt is still ready, but CPU0 is
still sitting in the same vprintk_emit()
5. CPU1 sees that no interrupt happened in 200ms, so timeout.
A normal system shouldn't see i2c timeouts anyway, so increasing the
timeout should help people debugging without hurting other people
excessively.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mapping range is inclusive between starting and ending addresses.
Signed-off-by: Christian König <christian.koenig@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When CONFIG_DEBUG_LOCK_ALLOC is defined, mutex magic is compared and
warned for (l->magic != l), here l is the address of mutex pointer.
In hid-sensor-hub as part of hsdev creation, a per hsdev mutex is
initialized during MFD cell creation. This hsdev, which contains, mutex
is part of platform data for the a cell. But platform_data is copied
in platform_device_add_data() in platform.c. This copy will copy the
whole hsdev structure including mutex. But once copied the magic
will no longer match. So when client driver call
sensor_hub_input_attr_get_raw_value, this will trigger mutex warning.
So to avoid this allocate mutex dynamically. This will be same even
after copy.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>