The problem is we're going to switch to a new context, which could be
the default context. The plan was to use restore inhibit, which would be
fine, except if we are using dynamic page tables (which we will). If we
use dynamic page tables and we don't load new page tables, the previous
page tables might go away, and future operations will fault.
CTXA runs.
switch to default, restore inhibit
CTXA dies and has its address space taken away.
Run CTXB, tries to save using the context A's address space - this
fails.
The general solution is to make sure every context has it's own state,
and its own address space. For cases when we must restore inhibit, first
thing we do is load a valid address space. I thought this would be
enough, but apparently there are references within the context itself
which will refer to the old address space - therefore, we also must
reinitialize.
v2: to->ppgtt is only valid in full ppgtt.
v3: Rebased.
v4: Make post PDP update clearer.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch was formerly known as, "Force pd restore when PDEs change,
gen6-7." I had to change the name because it is needed for GEN8 too.
The real issue this is trying to solve is when a new object is mapped
into the current address space. The GPU does not snoop the new mapping
so we must do the gen specific action to reload the page tables.
GEN8 and GEN7 do differ in the way they load page tables for the RCS.
GEN8 does so with the context restore, while GEN7 requires the proper
load commands in the command streamer. Non-render is similar for both.
Caveat for GEN7
The docs say you cannot change the PDEs of a currently running context.
We never map new PDEs of a running context, and expect them to be
present - so I think this is okay. (We can unmap, but this should also
be okay since we only unmap unreferenced objects that the GPU shouldn't
be tryingto va->pa xlate.) The MI_SET_CONTEXT command does have a flag
to signal that even if the context is the same, force a reload. It's
unclear exactly what this does, but I have a hunch it's the right thing
to do.
The logic assumes that we always emit a context switch after mapping new
PDEs, and before we submit a batch. This is the case today, and has been
the case since the inception of hardware contexts. A note in the comment
let's the user know.
It's not just for gen8. If the current context has mappings change, we
need a context reload to switch
v2: Rebased after ppgtt clean up patches. Split the warning for aliasing
and true ppgtt options. And do not break aliasing ppgtt, where to->ppgtt
is always null.
v3: Invalidate PPGTT TLBs inside alloc_va_range.
v4: Rename ppgtt_invalidate_tlbs to mark_tlbs_dirty and move
pd_dirty_rings from i915_address_space to i915_hw_ppgtt. Fixes when
neither ctx->ppgtt and aliasing_ppgtt exist.
v5: Removed references to teardown_va_range.
v6: Updated needs_pd_load_pre/post.
v7: Fix pd_dirty_rings check in needs_pd_load_post, and update/move
comment about updated PDEs to object_pin/bind (Mika).
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of implementing the full tracking + dynamic allocation, this
patch does a bit less than half of the work, by tracking and warning on
unexpected conditions. The tracking itself follows which PTEs within a
page table are currently being used for objects. The next patch will
modify this to actually allocate the page tables only when necessary.
With the current patch there isn't much in the way of making a gen
agnostic range allocation function. However, in the next patch we'll add
more specificity which makes having separate functions a bit easier to
manage.
One important change introduced here is that DMA mappings are
created/destroyed at the same page directories/tables are
allocated/deallocated.
Notice that aliasing PPGTT is not managed here. The patch which actually
begins dynamic allocation/teardown explains the reasoning for this.
v2: s/pdp.page_directory/pdp.page_directories
Make a scratch page allocation helper
v3: Rebase and expand commit message.
v4: Allocate required pagetables only when it is needed, _bind_to_vm
instead of bind_vma (Daniel).
v5: Rebased to remove the unnecessary noise in the diff, also:
- PDE mask is GEN agnostic, renamed GEN6_PDE_MASK to I915_PDE_MASK.
- Removed unnecessary checks in gen6_alloc_va_range.
- Changed map/unmap_px_single macros to use dma functions directly and
be part of a static inline function instead.
- Moved drm_device plumbing through page tables operation to its own
patch.
- Moved allocate/teardown_va_range calls until they are fully
implemented (in subsequent patch).
- Merged pt and scratch_pt unmap_and_free path.
- Moved scratch page allocator helper to the patch that will use it.
v6: Reduce complexity by not tearing down pagetables dynamically, the
same can be achieved while freeing empty vms. (Daniel)
v7: s/i915_dma_map_px_single/i915_dma_map_single
s/gen6_write_pdes/gen6_write_pde
Prevent a NULL case when only GGTT is available. (Mika)
v8: Rebased after s/page_tables/page_table/.
v9: Reworked i915_pte_index and i915_pte_count.
Also exercise bitmap allocation here (gen6_alloc_va_range) and fix
incorrect write_page_range in i915_gem_restore_gtt_mappings (Mika).
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v3+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Gen8, PDPs are saved and restored with legacy contexts (legacy contexts
only exist on the render ring). So change the ordering of LRI vs MI_SET_CONTEXT
for the initialization of the context. Also the only cases in which we
need to manually update the PDPs are when MI_RESTORE_INHIBIT has been
set in MI_SET_CONTEXT (i.e. when the context is not yet initialized or
it is the default context).
Legacy submission is not available post GEN8, so it isn't necessary to
add extra checks for newer generations.
v2: Use new functions to replace the logic right away (Daniel)
v3: Add missing pd load logic.
v4: Add warning in case pd_load_pre & pd_load_post are true, and add
missing trace_switch_mm. Cleaned up pd_load conditions. Add more
information about when is pd_load_post needed. (Mika)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes, but will improve code clarity and removed some
duplicated defines.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
AUX addresses are 20 bits long. Send out the entire address instead of
just the low 16 bits.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And remove one bogus * from i915_gem_gtt.c since that's not a
kerneldoc there.
v2: Review from Chris:
- Clarify memory space to better distinguish from address space.
- Add note that shrink doesn't guarantee the freed memory and that
users must fall back to shrink_all.
- Explain how pinning ties in with eviction/shrinker.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two code changes:
- Extract i915_gem_shrinker_init.
- Inline i915_gem_object_is_purgeable since we open-code it everywhere
else too.
This already has the benefit of pulling all the shrinker code
together, next patch adds a bit of kerneldoc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use both up/down manual ei calcuations for symmetry and greater
flexibility for reclocking, instead of faking the down interrupt based
on a fixed integer number of up interrupts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite commit 31685c258e
Author: Deepak S <deepak.s@linux.intel.com>
Date: Thu Jul 3 17:33:01 2014 -0400
drm/i915/vlv: WA for Turbo and RC6 to work together.
Other than code clarity, the major improvement is to disable the extra
interrupts generated when idle. However, the reclocking remains rather
slow under the new manual regime, in particular it fails to downclock as
quickly as desired. The second major improvement is that for certain
workloads, like games, we need to combine render+media activity counters
as the work of displaying the frame is split across the engines and both
need to be taken into account when deciding the global GPU frequency as
memory cycles are shared.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we idle, we set the GPU frequency to the hardware minimum (not user
minimum). We introduce a new variable to distinguish between the
different roles, and to allow easy tuning of the idle frequency without
impacting over aspects of RPS. Setting the minimum frequency should be a
safety blanket as the pcu on the GPU should be power gating itself
anyway. However, in order for us to do set the absolute minimum
frequency, we need to relax a few of our assertions that we do not
exceed the user limits.
v2: Add idle_freq
v3: Init idle_freq for vlv and add a bunch of WARNs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the batch buffer is too large to fit into the aperture and we need a
GTT mapping for relocations, we currently fail. This only applies to a
subset of machines for a subset of environments, quite undesirable. We
can simply check after failing to insert the batch into the GTT as to
whether we only need a mappable binding for relocation and, if so, we can
revert to using a non-mappable binding and an alternate relocation
method. However, using relocate_entry_cpu() is excruciatingly slow for
large buffers on non-LLC as the entire buffer requires clflushing before
and after the relocation handling. Alternatively, we can implement a
third relocation method that only clflushes around the relocation entry.
This is still slower than updating through the GTT, so we prefer using
the GTT where possible, but is orders of magnitude faster as we
typically do not have to then clflush the entire buffer.
An alternative idea of using a temporary WC mapping of the backing store
is promising (it should be faster than using the GTT itself), but
requires fairly extensive arch/x86 support - along the lines of
kmap_atomic_prof_pfn() (which is not universally implemented even for
x86).
Testcase: igt/gem_exec_big #pnv,byt
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88392
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add a WARN_ONCE for the impossible reloc case and explain in
a short comment why we want to avoid ping-pong.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes the interface consistent to old i915_gem_obj_ggtt_pin.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the original code then if WARN_ON(i915_is_ggtt(vm) != !!ggtt_view)
was true then we leak "vma". Presumably that doesn't happen often but
static checkers complain and this bug is easy to fix.
Fixes: c3bbb6f2825d ('drm/i915: Do not use ggtt_view with (aliasing) PPGTT')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allow for a larger receive data size, and check if the receiver returned
the number of bytes written. Without this, we've basically skipped all
the unwritten bytes for short writes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To keep things clear rename the intel_dp->supported_rates[] to
intel_dp->sink_rates[], and rename the supported_rates[] name we used
elsewhere for the intersection of source and sink rates to
common_rates[].
Cc: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
TODO: Is there an actually nice way to print an array of ints?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"P1273_DPLL_Programming Spreadsheet.xlsm" lists a boatload of
frequencies for eDP. Try to use them all.
For now I've decided not to add hardcoded DPLL dividers for these cases
since chv_find_best_dpll() works just fine.
I've not actually tested any of these since I don't have an eDP 1.4 panel.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Complain loudly if we ever attempt to overflow the the supported_rates[]
array. This should never happen since the sink_rates[] array will always
be smaller or of equal size. But should someone change that we want to
catch it without scribblign over the stack.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that intel_dp_max_link_bw() no longer considers the source
restrictions we may try to enable MST with 5.4GHz even when the source
doesn't support it. To fix that switch the code over to handle the link
rate in the same way as the SST code handles it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the gen9 checks from the code and issue DP_LINK_RATE_SET whenever
the sink reports to support it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Consider the link rates reported by the sink via
DP_SUPPORTED_LINK_RATES when checking modes against the max link
rate.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_dp_compute_config() only really needs to know the rates supported
by both source and sink, so hide the raw source and sink arrays from it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the sink vs. source limit mess from intel_dp_max_link_bw() and
just move the source restriction checks to intel_dp_source_rates().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
[danvet: Resolve conflict with WaDisableHBR2:skl patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that both source and sink rates are always filled in there's no need
for any special cases in intel_supported_rates().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once we've read the rates from the sink we don't have to mess with them,
so the caller can just look at the stored rates without doing extra
copies. If the sink doesn't support the new link rate stuff, we just
point the caller at the default_rates[] array.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The source rates don't change, so we can just point the caller at the
const arrays.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No point in converting from hardware format every single time, just
store the rates in the final format under intel_dp.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No point in using uint32_t here, just plain old int will do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GGTT views are only applicable when dealing with GGTT. Change the code to
reject ggtt_view where it should not be used and require it when it should
be.
v2:
- Dropped _ppgtt_ infixes, allow both types to be passed
- Disregard other but normal views when no view is specified
- More checks that valid parameters are passed
- More readable error checking
v3:
- Prefer WARN_ONCE over BUG_ON when there is code path for failure
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[danvet: Drop unecessary forward decl from earlier patch iterations.]
[danvet: Remove unused variable spotted by Tvrtko.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Regressed by this commit:
commit 3455454e18ca3f92c565700539e744c620d8276b
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Mar 3 15:21:56 2015 +0200
drm/i915: Add a for_each_intel_connector macro
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge because of numerous and interleaving conflicts and git
rerere getting confused a bit too often.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
All conflicts are because of -next patches backported to -fixes, so
just go with the code in -next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Backporting a couple of plane related fixes from drm-next to v4.0.
* tag 'drm-intel-fixes-2015-03-19' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Make sure the primary plane is enabled before reading out the fb state
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
- Fixing SDMA initialization when in non-HWS mode (debug mode)
- Memory leak fix when destroying kernel queue
- Fix number of available compute pipelines according to new firmware
* tag 'drm-amdkfd-fixes-2015-03-19' of git://people.freedesktop.org/~gabbayo/linux:
drm/radeon: Changing number of compute pipe lines
drm/amdkfd: Fix SDMA queue init. in non-HWS mode
drm/amdkfd: destroy mqd when destroying kernel queue
Some BCM47XX SoC routers have LEDs connected to extra PCIe bcma buses.
Handling them in arch code requires predictable GPIO numbers.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With patch '960d6d08e3 "mwifiex: delay skb allocation for RX
until cmd53 over"' we no more pass skb parameter to MP aggregation setup
helper function. We instead pass length to be aggregated.
This patch fixes an issue where we were passing length parameter of NULL
skb to aggregation routine resulting into crash. We should instead pass
rx_len received from mp_regs.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are no known BCM4354 PCIe devices released so removing
support from the driver until proven otherwise.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently support was added for the BCM4345 SDIO chipset by
commit 9c51026509 ("brcmfmac: Add support for BCM4345 SDIO chipset")
however this was verified using a BCM43455 device, which is
a more recent revision of the chip. This patch assure that
older revisions are not probed as they would fail.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Syed Asifful Dayyan <syedd@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch added support for the BCM43430 802.11n SDIO chipset.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BCM4356 PCIe wireless device was added recently but overlooked
the fact that the MODULE_FIRMWARE() macros were missing for the
firmwares needed by this device.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO uses a thread to handle all communication with the device,
for this data is exchanged between threads. This data needs proper
memory barriers to make sure that data "exchange" is going correct.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several host controllers supporting runtime-pm are causing issues
with our sdio wireless cards because they disable the sdio interrupt
upon going into runtime suspend. This patch avoids that by doing
a pm_runtime_forbid() call during the probe. Tested with Sony Vaio
Duo 13 which uses sdhci-acpi host controller.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's clear from the indenting that curly braces were intended here.
Fixes: e35000ead4 ('mwifiex: preprocess packets from TX queue')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the USB Id to link the D-Link DWA 130 USB Wifi adapter
to the rt2830 driver.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Pieter Truter <ptruter@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast is not yet properly supported for all connection types;
actually, only non-secure AP is supported. For all other cases,
fall back to old "pseudo-DMS" approach. Namely, for:
- PBSS
- secure connection
When re-routing MCAST Rx->Tx on the AP, do not Tx back to the origin
of the frame
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dedicated vring for multicast frames; this vring allocated for
AP and PBSS (both P2P GO and client) configurations
For short frames, use MCS0; for long - MCS1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sync with the wmi definitions from the firmware team
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix checkpatch warning:
WARNING: Prefer ether_addr_copy() over memcpy() if the
Ethernet addresses are __aligned(2)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>