Commit graph

287,481 commits

Author SHA1 Message Date
Sujith Manoharan
d808ecd874 ath9k: Fix MCI TX control
This patch makes sure that the antenna configuration
is used properly when setting AR_MCI_TX_CTRL.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-03 14:55:21 +02:00
Sujith Manoharan
e18e164e9a ath9k: Handle 2-ANT AR9565 in MCI reset
The value programmed in the BTCOEX control register
is different for each chip. This patch adds support
for 2-ANT, 1-ANT solutions based on AR9565.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-03 14:55:19 +02:00
Sujith Manoharan
d1d07813bb ath9k: Add new MCI configuration parameters
Several new MCI parameters need to be handled for
new chips, add them.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-03 14:55:18 +02:00
Sujith Manoharan
7d1805e194 ath9k: Remove useless check in MCI reset
If we fail to allocate the sched/gpm buffers when
initializing MCI, we bail out properly. Checking
them in ar9003_mci_reset() is unnecessary, so remove it.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-03 14:55:16 +02:00
Sujith Manoharan
ae55099f5b ath9k: Move MCI registers to reg_mci.h
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-03 14:55:13 +02:00
Geert Uytterhoeven
ff5e56859d iwlegacy: 4965-rs: Remove bogus colon after newline from debug message
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-03 14:22:46 +02:00
Kalle Valo
a437b3d928 * add triggers for firmware dump collection
* remove support for -9.ucode
 * new statitics API
 * rate control improvements
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJU9AGsAAoJEC0Llv5uNjIBatAP/39ocqHYTungymXnMhjB7JfV
 7QgJMivYcxpbzjIFYO1UuBh7QxSPpU6lQAFFaKzig6PdedIjrO2hclHszjyB35Ap
 D/FdVbsOll2RGV9jzOhjfppzN7igxeSkZWUk2CCcTuhSr4eKyTHbyVo7a2WE1w/n
 pW4lHuBSpwCmo7GFhiFvYm87CGNFTsbBUYpCCr+PMRmW3nL23CBApmswLqlEaGRN
 MPPhiE5y83V6X+u7yrO9sdgMUS3aYs/m+sOCgUXESlNsnWTYXQCpNAoNQb1P8gGA
 WxSqCyHvqHtFURvm+7EWcjFy29f850rLxmlsD1pkpAsYO5jzwXMPvKp9CTT364QH
 oQol5EaW3k/LgVdyaHX84MUDu28xdyF+RlZRVBZ9ukbxAiRdzhxXja2BupviopQT
 UFoj4z/Xvl9Iy7x8h7irKwlM8nhR/9siluXCU01uRgb7bfCQYghthcAiCrp9Xt2I
 6/B16H02xlNpVi1h5y69PRNUbponVsM546TDXBL9XFn9sHRJ2HsHYlBn2SfNXEQt
 bJzIAr1RMfDNAW9fz/egusgJZPNMfmyGHns7cu03ikDcIeR/q45bRfoQ4XrRTIWc
 Y5apNPFqwqnOSeznui1EASx4NOKsXXp6WBxWxA9SxajMO3l97GgczgkJ6o6BI5JE
 jdzQtUoIWfL+hu++tVFz
 =uonl
 -----END PGP SIGNATURE-----

Merge tag 'iwlwifi-next-for-kalle-2015-03-01' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

* add triggers for firmware dump collection
* remove support for -9.ucode
* new statitics API
* rate control improvements
2015-03-03 13:49:36 +02:00
Dave Airlie
ed9ed50ccc Revert "drm/rockchip: Flip select/depends in Kconfig"
This reverts commit 9c58e8dbd3.

This doesn't seem to fully fix this, Kbuild who knows.

Signed-off-by: Dave Airlie <airlied@redhat.com>
2015-03-03 21:11:34 +10:00
Daniel Vetter
9c58e8dbd3 drm/rockchip: Flip select/depends in Kconfig
Otherwise Kconfig gets confused and somehow ends up creating a 2nd drm
submenu. I couldn't find i915 because of this any more at first.

Cc: Andy Yan <andy.yan@rock-chips.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: linux-kbuild@vger.kernel.or
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
2015-03-03 20:31:16 +10:00
Stefan Agner
e8361f70a8 spi: spi-imx: use correct enumeration type
The fourth argument of dmaengine_prep_slave_sg needs to be of the
enumeration type dma_transfer_direction instead of dma_data_direction.
Since the used enumeration values actually stay the same, this is not
an actual issue at runtime.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-03 09:58:24 +00:00
Dave Airlie
9d0685ae04 imx-drm fixes for mode fixup, dw_hdmi/imx, and parallel-display
- A clock fix for too large pixel clocks depending on the
   DI clock flag simplification patch
 - Pruning of unsupported modes and a missing end of array element
   for dw_hdmi-imx
 - LVDS modeset fix for mode fixup
 - Fix parallel-display deferred probing if drm_panel is used
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJU68LkAAoJEFDCiBxwnmDrU88P/093tyHInYjgzDS9UIyNHKfK
 TbGzpOP/WiaDcN5MxY2aBCUwzXxRZacQBSxTZLPwT5Zm0vuLbYDlqII5ttH6xI1A
 eSFhH89zntcWHHtbu5iQ0BE6doKpyzDX8RD/0uS/DANdKfdyyl51mv+FSYKuoOQR
 OW3SGrFY6YrWW2Fmi7IstJ4vfdM3f0HO/kaMAMnADCdPMquObrL0LMLI+r8JVqEQ
 FpaNwzD/KuyBoaYuNm+l/LsMkfsZZdTVuwnRLqNx+avB/a318GdN6Argzh23kEDb
 cxyzMv9/eP/hMzMAMaoCdlhcgWnBWQ9rPP9CVVHjT7juv4Bj4/IIfWimXNUOdfE1
 ld1jKxsx07xKQHq+Vmh/648N+0utUABZzq9I/toyKDa37zC3pDMeG1ZgELnEXbN8
 8mf69SLE62hZEuempM54h2enMPH4nbvOVKcRMZXIpGNiPyNK890B9aijbZUVQ9Wm
 K5td2bKbaqSiq17PRyFddFPy9CkDASMFwiLZ9cfeCoVYb1tiFAV6maBEsTJPi18H
 OVhy5CC5PeR8VlqaKcR3Nt/+pTtl1vkou2yAvYFMeO3iX1U3VQ1J5o0MuAA2E1sC
 /mRJ4jCbMzlCFsqo/2CSu/DG2gF9UfhU/CQ4vLTNU09lBWTRwkeC7JHnJUawVSJL
 LTcGvb1Fb2R0NkE7nqET
 =CrJz
 -----END PGP SIGNATURE-----

Merge tag 'imx-drm-fixes-2015-02-24' of git://git.pengutronix.de/git/pza/linux into drm-fixes

imx-drm fixes for mode fixup, dw_hdmi/imx, and parallel-display

- A clock fix for too large pixel clocks depending on the
  DI clock flag simplification patch
- Pruning of unsupported modes and a missing end of array element
  for dw_hdmi-imx
- LVDS modeset fix for mode fixup
- Fix parallel-display deferred probing if drm_panel is used

* tag 'imx-drm-fixes-2015-02-24' of git://git.pengutronix.de/git/pza/linux:
  DRM: i.MX: parallel display: Support probe deferral for finding DRM panel
  drm/imx: imx-ldb: enable DI clock in encoder_mode_set
  drm/imx: dw_hdmi-imx: add end of array element to current control array
  drm/imx: dw_hdmi-imx: add mode_valid callback prune unsupported modes
  gpu: ipu-v3: do not divide by zero if the pixel clock is too large
2015-03-03 19:57:41 +10:00
Sravanthi Tangeda
ce458fcfcb i40e/i40evf: Bump versions
Bump i40e to 1.2.10 and i40evf to 1.2.4

Change-ID: I48aa64df05fcc8356e7026f3a9e69ecf78d0c785
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:31 -08:00
Neerav Parikh
fc51de96ed i40e: Only enable TC0 for NIC partition type
In case of MFP mode the driver was returning incorrect number of TCs
for partitions that are not enabled for iSCSI. Though the driver does
not configure these TCs in the Tx scheduler for the NIC partitions;
it does use this map to setup the queue mappings.

This patch fixes this and keeps all the NIC partitions to the default
PF TC i.e. TC0.

Change-ID: Iede214c907e7bac1356e999049b9f642759512b3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:30 -08:00
Neerav Parikh
15d504b946 i40e: Register DCBNL ops in MFP mode
Allow DCBNL operations in MFP mode to allow query of port DCB settings
via all the PFs and register iSCSI APP on iSCSI enabled PF.

Change-ID: I34cc39b4665d0a631847d4079350d3814f02381e
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:30 -08:00
Mitch Williams
ed250ecc55 i40evf: ethtool RSS fixes
Add an extra check to make sure that the indirection table pointer is
valid before dereferencing it.

Change-ID: I698adbf3daff03081d01f489dc95a9f1ad8b12f1
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:29 -08:00
Anjali Singhai Jain
66ddcffb1a i40e: Fix RSS size at init since default num queue calculation has changed
With changes to default number of queue pairs that the interface comes up with
from 1 per online CPU to 1 per lan_msix, we need to make sure we recalculate
rss_size. We will now recalculate rss_size based on number of queues enabled in
the VSI.

Without this fix if the max_lan_msix < num_online_cpu we will be coming up
with fewer queues but will be populating rss_size based on num_online_cpus.
This will result in packets getting silently dropped because RSS LUT has queues
that are not enabled.

Change-ID: Ifac8796ce1be1758bb0c34f38dbf4a3a76621e76
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:29 -08:00
Anjali Singhai Jain
5db4cb59cd i40e: Move RSS table size for VSIs to the VSI struct
Since all VSIs don't have the same RSS table size,
have one for each VSI instead of having a single define
for RSS table size

Change-ID: Ic2c7c66e4a389d4b6c8841a707510a9735041f02
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:28 -08:00
Anjali Singhai Jain
f8faaa40b4 i40e/i40evf: Add missing packet types for VXLAN encapsulated packet types
We were missing a few packet types for VXLAN offload. This patch fixes
that.

Change-ID: I4b23aa0b08e40ed49d0df6c49a5ed9f2009b44ce
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:27 -08:00
Neerav Parikh
750fcbcf18 i40e: Fix issue with removal of apps from DBCNL app table
This patch fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local
DCBX application configuration TLVs.

Change-ID: I1f1ee04c81c145071b2ab15657546eb10b81fadb
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:27 -08:00
Anjali Singhai Jain
025b4a545f i40e: Add FW check to disable DCB and wrap autoneg workaround with FW check
For FW < 4.33 DCB should be disabled.
Also Autoneg workaround to avoid Rx stall is still needed for FW < 4.33.

Change-ID: Iff36ad86be2f597e7701096014d6d094332a9a21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:26 -08:00
Anjali Singhai Jain
9a3bd2f1e3 i40e: Enable more than 64 qps for the Main VSI
When running in a single TC mode the HW can be configured to enable more
than max RSS qps for the Main VSI. This  patch makes it possible to
enable as many as num_online_cpus().

ethtool -L can still be used to reconfigure number of qps
to a smaller value.

Change-ID: I3e2df085276982603d86dfd79477c0ada8d30b8f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:25 -08:00
Mitch Williams
8f40082434 i40e: don't disable PF LB when disabling VFs
Since we now have functionality to enable and disable PF loopback at
runtime, don't try to do it automatically. Removing this call also gets
rid of a bogus error message when removing the PF module with VFs
enabled.

Change-ID: Ic38652d8a3b9498d96113bfaa5ea7bad050862e9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:25 -08:00
Akeem G Abodunrin
579b23d8dc i40e: Add safety net for switch calling
This patch adds default case to handle unmatched switch calls.

Change-ID: Icd203570a1dc5322c1038f68b98a83195e8ad28c
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:24 -08:00
Shannon Nelson
7edf810c61 i40e/i40evf: print FW build number in version string
Include the FW build number in the formatted FW version string.  In order
to fit within ethtool's 32 character limit, the etrack's unused high order
bits are trimmed as is the leading 0 for the NVM version.  This leaves
us with 2 character left for if/when the etrack id goes to 5 hex chars
and the NVM major number goes to 2 chars.

Change-ID: Icb004c4b9b14a2f54dd200b467fcc1d7b9297308
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:24 -08:00
Neerav Parikh
d40d00b1c2 i40e: Skip the priority tagging if DCB is not enabled
If DCB is not enabled priority tagging is not needed
so skip over that section.

Change-ID: Ia3f3fa07945b421259a9ca38329d6d1cbd6c6bcc
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:23 -08:00
Matthew Vick
eca3204765 fm10k: Resolve various spelling errors and checkpatch warnings
Fix a few silly typos in the code and checkpatch warnings in support of
general code cleanliness.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:23 -08:00
Matthew Vick
5bf33dc687 fm10k: Implement ndo_features_check
The introduction of ndo_features_check allows drivers to report their
offload capabilities per-skb. Implement this in fm10k to take advantage
of this new functionality.

Reported-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:22 -08:00
Matthew Vick
8c1a90aa49 fm10k: Modify tunnel length header check when offloading
The FM10000 host interface can only support up to 184 bytes when
performing tunnel offloads. Because of this, a check was added to
prevent the driver from attempting to feed a header to the hardware too
big for it to parse. Make this check a little more robust by calculating
the inner L4 header length based on whether it is TCP or UDP.

Cc: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-03-03 01:07:21 -08:00
Colin Ian King
393d23c4e2 mtd: atmel_nand: fix typo in dev_err error message
Fix typo, "Unkown" -> "Unknown"

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-03-02 22:59:43 -08:00
Geert Uytterhoeven
5e0899db69 mtd: nand: MTD_NAND_HISI504 should depend on HAS_DMA
If NO_DMA=y:

    drivers/built-in.o: In function `hisi_nfc_probe':
    hisi504_nand.c:(.text+0x23e646): undefined reference to `dmam_alloc_coherent'

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-03-02 22:55:56 -08:00
Max Mansfield
c7d373c3f0 usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
This patch integrates Cyber Cortex AV boards with the existing
ftdi_jtag_quirk in order to use serial port 0 with JTAG which is
required by the manufacturers' software.

Steps: 2

[ftdi_sio_ids.h]
1. Defined the device PID

[ftdi_sio.c]
2. Added a macro declaration to the ids array, in order to enable the
jtag quirk for the device.

Signed-off-by: Max Mansfield <max.m.mansfield@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2015-03-03 07:47:06 +01:00
Ben Hutchings
dacc73e0cf sh_eth: Really fix padding of short frames on TX
My previous fix to clear padding of short frames used skb->len as the
DMA length, assuming that skb_padto() extended skb->len to include the
padding.  That isn't the case; we need to use skb_put_padto() instead.

(This wasn't immediately obvious because software padding isn't
actually needed on the R-Car H2.  We could make it conditional on
which chip is being driven, but it's probably not worth the effort.)

Reported-by: "Violeta Menéndez González" <violeta.menendez@codethink.co.uk>
Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-02 21:30:56 -05:00
Ben Hutchings
9b4a6364a6 Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
This reverts commit fd9af07c34.

The hardware manual states that the frame error and multicast bits are
copied to bits 9:0 of RD0, not bits 25:16.  I've tested that this is
true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too
long) and RFS8 (multicast).

Also adjust a comment to agree with this.

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-02 21:30:56 -05:00
Ben Hutchings
6ded286555 sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
In case of RX ring underrun (RDE), we attempt to reset the software
descriptor pointers (dirty_rx and cur_rx) to match where the hardware
will read the next descriptor from, as that might not be the first
dirty descriptor.  This relies on reading RDFAR, but that register
doesn't exist on all supported chips - specifically, not on the R-Car
chips.  This will result in unpredictable behaviour on those chips
after an RDE.

Make this pointer reset conditional and assume that it isn't needed on
the R-Car chips.  This fix also assumes that RDFAR is never exposed at
offset 0 in the memory map - this is currently true, and a subsequent
commit will fix the ambiguity between offset 0 and no-offset in the
register offset maps.

Fixes: 79fba9f517 ("net: sh_eth: fix the rxdesc pointer when rx ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-02 21:30:56 -05:00
Ben Hutchings
7d7355f58b sh_eth: Ensure proper ordering of descriptor active bit write/read
When submitting a DMA descriptor, the active bit must be written last.
When reading a completed DMA descriptor, the active bit must be read
first.

Add memory barriers to ensure that this ordering is maintained.

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-02 21:30:56 -05:00
Eduardo Valentin
78045bfe85 Merge branch 'fixes' of github.com:lmajewski/linux-samsung-thermal into work-fixes
Pull samsung thermal fixes from Lukasz Majewski:
"Changes:
- Exynos7 power down detection mode fix
- Fix for cpufreq cooling device regression
- Updating MAINTAINER's entry for Samsung Exynos Thermal"

Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
2015-03-02 22:18:31 -04:00
Alexander Aring
263be3326b at86rf230: restore trx len when needed
In the most cases the spi messages has a length of two. Currently we
always set the the len field to two before transmit a spi message. In
cases for read out/write in the frame buffer we need another len. This
patch use trx len two as default. For the frame buffer cases we restore
the trx len to two on success and failure. This will reduce the len
setting of two when it's already two.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-03-03 02:15:25 +01:00
Alexander Aring
31fa74344c at86rf230: remove multiple dereferencing for ctx
This patch cleanups the referencing for the state change context
variable. The state change context should only set once and this is by
initial a state change. This patch will use the initial state change
variable in the complete handler of the state change by using the ctx
context which should be always the same like the initial state change
context.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-03-03 02:15:25 +01:00
Alexander Aring
cca990c85d at86rf230: remove multiple dereferencing for irq
By holding the irq variable inside at86rf230_state_change we can squash
some multiple dereferencing for getting irq num.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-03-03 02:15:25 +01:00
Alexander Aring
74de4c804c at86rf230: refactor receive handling
This patch refactor the receive handling into one function.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-03-03 02:15:25 +01:00
Alexander Aring
ef5428a138 at86rf230: cleanup and squash stack variable
I had this variable because I thought it would be protected by
disable/enable irq but this is not true. It's protected by stop/wake
netdev queue which is called by ieee802154_xmit_complete.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-03-03 02:15:25 +01:00
Alexander Aring
ba6d223932 at86rf230: add transmit retry support
This patch introduce a transmit retry handling into at86rf230 transmit
path. Current behaviour is to wait the normal receive time if we want
to go into STATE_TX_ON when the transceiver is in STATE_BUSY_RX_AACK
which indicates that a frame is currently receiving. A non force state
change will not interrupt the the receiving state.

The current behaviour is that after the normal receive time we will
start a force change into STATE_TX_ON. With this patch we do seven
retries to go into STATE_TX_ON without forcing. After we hit the
AT86RF2XX_MAX_TX_RETRIES we will start the force state change.
This is a polling like method to go into STATE_TX_ON in times of maximum
receiving time.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-03-03 02:15:24 +01:00
Kim, Ben Young Tae
3267c884ce Bluetooth: btusb: Add support for QCA ROME chipset family
This patch supports ROME Bluetooth family from Qualcomm Atheros,
e.g. QCA61x4 or QCA6574.

New chipset have similar firmware downloading sequences to previous
chipset from Atheros, however, it doesn't support vid/pid switching
after downloading the patch so that firmware needs to be handled by
btusb module directly.

ROME chipset can be differentiated from previous version by reading
ROM version.

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 16 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e300 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  8 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e360 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-03-03 02:07:01 +01:00
Kim, Ben Young Tae
ace3198258 Bluetooth: btusb: Add setup callback for chip init on USB
Some of chipset does not allow to send a patch or config files through
HCI VS channel at early stage as well as they don't support to send
USB patch files to other channel except USB bulk path.

New callback added is for initialization of BT controller through USB

Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-03-03 02:07:00 +01:00
Ping Cheng
e0d41fd435 HID: wacom: rely on actual touch down count to decide touch_down
touch_down is a flag to indicate if there are touches on tablet
or not. Since one set of touch events may be posted over more
than one data packet/touch frame, and pen may come in proximity
while touch events are partially sent, counting all touch events
for the set reflects the actual status of touch_down.

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-03 00:27:10 +01:00
Ping Cheng
486b908d44 HID: wacom: do not send pen events before touch is up/forced out
If pen comes in proximity while touch is down, we force touch up
before sending pen events. Otherwise, there can be unfinished
touch events compete with pen events. This idea has been fully
implemented for Tablet PCs. But other tablets that support both
pen and touch are not fully considered.

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-03 00:27:09 +01:00
Scott Branden
0c7e67a928 Input: add driver for Broadcom keypad controller
Broadcom Keypad controller is used to interface a SoC with a matrix-type
keypad device. The keypad controller supports multiple row and column
lines. A key can be placed at each intersection of a unique row and a
unique column. The keypad controller can sense a key-press and key-release
and report the event using an interrupt to the CPU.

Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-03-02 15:16:52 -08:00
Arnd Bergmann
4a6155a465 Input: sun4i-ts - add thermal driver dependency
The sun4i-ts driver has had a dependency on the thermal code
with the addition of the thermal zone sensor support, but this
is not currently enforced in Kconfig, so with TOUCHSCREEN_SUN4I=y,
THERMAL=m and THERMAL_OF=y we get

drivers/built-in.o: In function `sun4i_ts_remove':
:(.text+0x2376f4): undefined reference to `thermal_zone_of_sensor_unregister'
drivers/built-in.o: In function `sun4i_ts_probe':
:(.text+0x237a94): undefined reference to `thermal_zone_of_sensor_register'
:(.text+0x237c00): undefined reference to `thermal_zone_of_sensor_unregister'

We need the dependency on THERMAL in order to ensure that this
driver becomes a loadable module if the thermal support itself
is modular, while the dependency on THERMAL_OF is a runtime
dependency and the driver will still build if it is missing.
It is entirely possible to build sun4i-ts without THERMAL_OF
just to use the hwmon sensors and/or touchscreen.

Fixes: 2236971079 ("Input: sun4i-ts - add thermal zone sensor support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[wens@csie.org: Fix description and Kconfig dependencies]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-03-02 15:15:50 -08:00
Linus Torvalds
023a6007a0 Two GPIO fixes for the v4.0 kernel series:
- Fix a translation problem in of_get_named_gpiod_flags()
 - Fix a long standing container_of() mistake in the TPS65912
   driver.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJU9EyeAAoJEEEQszewGV1z16YP/1/sPyqZpj6f6Z9Q3shAffGY
 chDyxuaf8X7weiRd7vap93BPnnYJeJQkLQQCOEbsGmGsXOxLCIpqv6ShINYsRcnD
 aUnhVt6c9PxxkllfDaBJfKgXOa+M647Uj0Bzfkl2W9zuIJaeyGqUVOu7rvsFmf8f
 44ofuNdHYKHgkFtcdhPthIHC3zhGpDUwKR4OUElgZd89sHLcIEYVT0KQddRY0qE/
 RVb3KaP4FrlEL9vFrXABDsh9UufvN29gybAJSuCe/fgqdLAxTsOIoKktA8xNSXZR
 wWj47pjopRE1/GIJ03ug0boiv0eKwumvUwAn5xlrdJurcIGh0NrHSSF9JPCgMdSK
 48+45k+MmYQPJVQG/n4NRgAUv10KbN+0u/4MViNLYzTQuGkoCriei7/FL5/04TOi
 52xpdJ3Nf0R/ItzpPrmoNRx8vWzt7vg3SLiQi3kzeej9ej1DW+a9OvDeGiImAtKO
 MEx0Q3Nm5VNQ5kjiZaRan8/HK/Yys1fESqYdlbOxAEPRaCh3tl78x1jIN+ulivIn
 myyMyCn3H5y6DEYqORRyw97egqvCjLz6/BqIIuApKNVOy+gpkdmYtpL1GMEOWOJK
 J+w1fx7cnHXBhGAQHKgmqFvHF9L1Bqadd3RlvXk17XDhxM9mRWka4S4E+08/BEtb
 qL7OgdAzI0EPn0WxWBKM
 =5nhV
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO fixes from Linus Walleij:
 "Two GPIO fixes:

   - Fix a translation problem in of_get_named_gpiod_flags()

   - Fix a long standing container_of() mistake in the TPS65912 driver"

* tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: tps65912: fix wrong container_of arguments
  gpiolib: of: allow of_gpiochip_find_and_xlate to find more than one chip per node
2015-03-02 14:13:39 -08:00
Linus Torvalds
10d6dfc197 Merge branch 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal management fixes from Eduardo Valentin:
 "Specifics:

   - Several fixes in tmon tool.

   - Fixes in intel int340x for _ART and _TRT tables.

   - Add id for Avoton SoC into powerclamp driver.

   - Fixes in RCAR thermal driver to remove race conditions and fix fail
     path

   - Fixes in TI thermal driver: removal of unnecessary code and build
     fix if !CONFIG_PM_SLEEP

   - Cleanups in exynos thermal driver

   - Add stubs for include/linux/thermal.h.  Now drivers using thermal
     calls but that also work without CONFIG_THERMAL will be able to
     compile for systems that don't care about thermal.

  Note: I am sending this pull on Rui's behalf while he fixes issues in
  his Linux box"

* 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: int340x_thermal: Ignore missing _ART, _TRT tables
  thermal/intel_powerclamp: add id for Avoton SoC
  tools/thermal: tmon: silence 'set but not used' warnings
  tools/thermal: tmon: use pkg-config to determine library dependencies
  tools/thermal: tmon: support cross-compiling
  tools/thermal: tmon: add .gitignore
  tools/thermal: tmon: fixup tui windowing calculations
  tools/thermal: tmon: tui: don't hard-code dialog window size assumptions
  tools/thermal: tmon: add min/max macros
  tools/thermal: tmon: add --target-temp parameter
  thermal: exynos: Clean-up code to use oneline entry for exynos compatible table
  thermal: rcar: Make error and remove paths symmetrical with init
  thermal: rcar: Fix race condition between init and interrupt
  thermal: Introduce dummy functions when thermal is not defined
  ti-soc-thermal: Delete an unnecessary check before the function call "cpufreq_cooling_unregister"
  thermal: ti-soc-thermal: bandgap: Fix build warning if !CONFIG_PM_SLEEP
2015-03-02 14:08:10 -08:00