AM43xx supports pixel clock divider of 1, just like all OMAP3+ SoCs. Fix
the minimum divider value.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The MSM IOMMU driver unconditionally calls bus_set_iommu(), which is a
very stupid thing to do on multi-platform kernels. While marking the
driver BROKEN may seem a little extreme, there is no other way to make
the driver skip initialization. One of the problems is that it doesn't
have devicetree binding documentation and the driver doesn't contain a
struct of_device_id table either, so no way to check that it is indeed
valid to set up the IOMMU operations for this driver.
This fixes a problem on Tegra20 where the DRM driver will try to use the
obviously non-existent MSM IOMMU.
Marking the driver BROKEN shouldn't do any harm, since there aren't any
users currently. There is no struct of_device_id table, so the device
can't be instantiated from device tree, and I couldn't find any code
that would instantiate a matching platform_device either, so the driver
is effectively unused.
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Olav Haugan <ohaugan@codeaurora.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The Rockchip IOMMU driver unconditionally executes code and registers a
struct iommu_ops with the platform bus irrespective of whether it runs
on a Rockchip SoC or not. This causes problems in multi-platform kernels
where drivers for other SoCs will no longer be able to register their
own struct iommu_ops or even try to use a struct iommu_ops for an IOMMU
that obviously isn't there.
The smallest fix I could think of is to check for the existence of any
Rockchip IOMMU devices in the device tree and skip initialization
otherwise.
This fixes a problem on Tegra20 where the DRM driver will try to use the
obviously non-existent Rockchip IOMMU.
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The OMAP IOMMU driver unconditionally executes code and registers a
struct iommu_ops with the platform bus irrespective of whether it runs
on an OMAP SoC or not. This causes problems in multi-platform kernels
where drivers for other SoCs will no longer be able to register their
own struct iommu_ops or even try to use a struct iommu_ops for an IOMMU
that obviously isn't there.
The smallest fix I could think of is to check for the existence of any
OMAP IOMMU devices in the device tree and skip initialization otherwise.
This fixes a problem on Tegra20 where the DRM driver will try to use the
obviously non-existent OMAP IOMMU.
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Suman Anna <s-anna@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The Exynos System MMU driver unconditionally executes code and registers
a struct iommu_ops with the platform bus irrespective of whether it runs
on an Exynos SoC or not. This causes problems in multi-platform kernels
where drivers for other SoCs will no longer be able to register their
own struct iommu_ops or even try to use a struct iommu_ops for an IOMMU
that obviously isn't there.
The smallest fix I could think of is to check for the existence of any
Exynos System MMU devices in the device tree and skip initialization
otherwise.
This fixes a problem on Tegra20 where the DRM driver will try to use the
obviously non-existent Exynos System MMU.
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Cc: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Various build/boot bots have reported WARNs being triggered by the ARM
iopgtable LPAE self-tests on i386 machines.
This boils down to two instances of right-shifting a 32-bit unsigned
long (i.e. an iova) by more than the size of the type. On 32-bit ARM,
this happens to give us zero, hence my testing didn't catch this
earlier.
This patch fixes the issue by using DIV_ROUND_UP and explicit case to
to avoid the erroneous shifts.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This is a follow up patches after adding i2c mux adapter for bypass
mode. Potentially many different types of sensor can be attached to
INVMPU6XXX device, which can be connected to main cpu i2c bus in
bypass mode.
Why do we need this?
The system ACPI table entry will consist of only one device for
INV6XXX, assuming that this driver will handle all connected sensors.
That is not true for the Linux driver. There are bunch of IIO drivers
for each sensors, hence we created a mux on this device. So to load
these additional drivers, we need to create i2c devices for them
in this driver using this mux adapter.
There are multiple options:
1. Use the auto detect feature, this needs a new i2c class for the
adapter as the existing HWMON class is not acceptable. Also the
autodetect has overhead of executing detect method for each
matching class of adapters.
This is a simple implementation. This option was previously submitted
with not a happy feedback.
2. Option is use ACPI magic and parse the configuration data. What
we need to create a i2c device at a minimum is address and a name.
Address can be obtained for secondary device in more or less in a
standard way from using _CRS element. But there is no name. To get
name we need to process proprietary vendor data. Not having name is
not fun, as you have to create device using the device name of
INVN6XXXX, respecting driver duplicate name space restriction.
Also each client driver needs to have this name in the id table.
Since multiple driver can be loaded, the driver should be able to
detect its presence and gracefully exit for the other client driver
to take it over.
So we use two step process:
- Use DMI to id platform and parse propritery data. This is not uncommon
for many x86 platform specific driver. We will get both name and address.
The change created necessary infrastructure to add more properitery vendor
data parsing.
- If DMI match fails, then create device on INV6XXX-client (we can't
create with same name as INV6XXX as it will cause duplicate name and driver
model will reject.) With this each client sensor driver which needs to get
attached via INV6XXXX, need this name in the id table and detect the
physical presence of sensor in probe and exit if not found.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The regmap_access_table and regmap_config structures may be const
because they are not modified by the driver and regmap_init() accepts
pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix sparse warning:
warning: symbol 'gpmc_cs_get_name' was not declared. Should it be static?
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Some GPMC_CONFIG7 register bits marked as "RESERVED", means they
shouldn't be overwritten. A typical approach to handle such bits called
"Read-Modify-Write". Writing procedure used in gpmc_cs_set_memconf()
utilizes RMW technique, but implemented incorrectly. Due to obvious typo
in code read register value is being rewritten by another value, which
leads to loss of read RESERVED bits. This patch fixes this.
While at it, replace magic numbers with named constants to improve code
readability.
Signed-off-by: Semen Protsenko <semen.protsenko@globallogic.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
As pxa_timer_common_init() is only called in init context, mark it as
such, and quiesce the compiler warnings :
WARNING: vmlinux.o(.text.unlikely+0x45d4): Section mismatch in reference
from the function pxa_timer_common_init() to the function
.init.text:sched_clock_register()
WARNING: vmlinux.o(.text.unlikely+0x4610): Section mismatch in reference
from the function pxa_timer_common_init() to the function
.init.text:clocksource_mmio_init()
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We have two race conditions in the probe code which could lead to a null
pointer dereference in the interrupt handler.
The interrupt handler accesses the clockevent device, which may not yet be
registered.
First race condition happens when the interrupt handler gets registered before
the interrupts get disabled. The second race condition happens when the
interrupts get enabled, but the clockevent device is not yet registered.
Fix that by disabling the interrupts before we register the interrupt and enable
the interrupts after the clockevent device got registered.
Reported-by: Gongbae Park <yongbae2@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The Kconfig options for the asm9260 timer is wrong as it can be selected by
another platform with allyes config and thus leading to a compilation failure
as some non arch related code is pulled by the compilation.
Fix this by having the platform Kconfig to select the timer as it is done for
the others drivers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Conflicts:
drivers/clocksource/Kconfig
The commit below didn't update the max_ht_ampdu_exponent
for the devices listed in iwl-[1-6]000.c which, in result,
became 0 instead of 8K. This reduced the size of the Rx
AMPDU from 64K to 8K which had an impact in the Rx
throughput. One user reported that because of this, his
downstream throughput droppped by a half.
CC: <stable@vger.kernel.org> [3.19]
Fixes: c064ddf318 ("iwlwifi: change max HT and VHT A-MPDU exponent")
Reported-and-tested-by: Valentin Manea <linux-wireless@mrs.ro>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This return 0 without setting atomic bits on fb == crtc->cursor->fb
where causing frontbuffer false positives.
According to Daniel:
The original regression seems to have been introduced in the original
check/commit split:
commit 757f9a3e5b
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Wed Sep 24 14:20:24 2014 -0300
drm/i915: move check of intel_crtc_cursor_set_obj() out
Which already cause other trouble, resulting in the check getting moved in
commit e391ea882b
Author: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Date: Wed Sep 24 14:20:25 2014 -0300
drm/i915: Fix not checking cursor and object sizes
The frontbuffer tracking itself only was broken when we shifted it into
the check/commit logic with:
commit 32b7eeec4d
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Wed Dec 24 07:59:06 2014 -0800
drm/i915: Refactor work that can sleep out of commit (v7)
v2: When putting more debug prints I notice the solution was simpler
than I thought. AMS design is solid, just this return was wrong.
Sorry for the noise.
v3: Remove the entire chunck that would probably
be removed by gcc anyway. (by Daniel)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bump i40e to 1.2.9 and i40evf 1.2.3
Also update the copyright year.
Change-ID: I345d777e94abd0acffe6a28793f675d251a86299
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the netdev name to the VF misc vector name. Without
this patch, all the interrupts show the same info, so it difficult to
distinguish them.
Change-ID: I247828697e1373ecfb5f8dc1bc9618e98a7f4942
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow an application to query the i40e driver's private flags to get the
status of NPAR enablement. This will be used by applications to determine
if there are NPAR specific features available.
Change-ID: Ia6d9477a48f9c4cb41ca022bd433f77da3f2146c
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set FLAG_RD for send_driver_version AQ command.
Change-ID: I8253051eff85a1d4b5a4e12ce0395b65ceb91e62
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the RX routine in use to the features log message.
Change-ID: Ifbbf28fb7f42b9a3d2828586488e9e6331107dd5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setup FCoE netdev device type as "fcoe", so that it shows up in
sysfs as FCoE device.
Change-ID: Ie13a1a332dba4d5802586926104ee01ef20da44f
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BUF flag must be set for indirect AQ command.
Change-ID: I6819718a47baf69d1a91ebaed89f735ed6e86025
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for bridge offload ndo_ops getlink and setlink to
enable bridge hardware mode as per the mode set via IFLA_BRIDGE_MODE.
The support is only enabled in case of a PF VSI and not available for
any other VSI type.
By default the i40e driver inserts a bridge as part of the bring-up
when a FDIR type VSI and/or a FCoE VSI is created. This bridge is
created in VEB mode by default i.e. after creating the bridge using
"Add VEB" AQ command the loopback for the PF's default VSI is enabled.
The patch adds capability where all the VSIs created as downlink to
the bridge inherits the loopback property and enables loopback only
if the uplink bridge is operating in VEB mode.
Hence, there is no need to explicitly enable loopback as part of
allocating resources for SR-IOV VFs and call to do that has been
removed.
In case a user-request is made either via "bridge" utility or using
the bridge netlink interface that requires to change the hardware
bridge mode then that would require a PF reset and rebuild of the
switch hierarchy.
Also update the copyright year.
Change-ID: I4d78fc1c83158efda29ba7be92239b74f75d6d25
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add configfs controls to get, set and commit NPAR BW configurations.
We export three controls:
min_bw - Can take a value from 0 to 100 inclusive
max_bw - Can take a value from 1 to 100 inclusive
commit - A write-only control that accepts only a value of 1 and will
cause the BW settings to be permanently committed to NVM so
that they are persistent across power cycles and system
resets
The BW values are relative and are expressed as percentages. For more
information on the interpretation of the BW settings see the Dell
specifications for NPAR.
Also update the copyright year.
Change-ID: Id7496ca65630b5037e32ba6a5a748fbc1632881b
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-By: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to be able to get, set and commit permanently the NPAR
partition BW configuration through configfs. These are necessary
precursor functions for that feature.
Also update the copyright year.
Change-ID: I9d5ca160a9288145f1dd2042994028679fff55f3
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an IOMMU is in use, the packet split receive path shows a distinct
advantage over the single-buffer path because it minimizes DMA mapping
and unmapping. However, this is not an advantage for systems with no
IOMMU. At init time, check to see if an IOMMU is enabled and enable
packet split receives.
Change-ID: I4f70d2e9c31bbea3dc8fd0c5734959a6e6602210
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Copy setting from ethtool to the HW specific struct to actually
enable prints. Change print from i40e to i40evf to differentiate
drivers in bare metal scenarios.
Also update the copyright year.
Change-ID: I06fee26247299a08f2e1c70fc811a9ea0931c4dd
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a struct to the VSI struct to keep track of rxnfc
settings done via ethtool. Without this patch, the device can only
list the options available, not the current settings and this is not
clear to the user. Without current settings, the available settings
never changing looks like a bug.
Also update the copyright year.
Change-ID: I087bbfdb33b330496a671630a7586773e3b3e589
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a requested speed variable to the link_status struct to store the
last speeds we requested from the firmware (the speeds the FW will be
advertising with if autoneg is enabled).
Use the advertised speed settings in get_settings in ethtool now that
we have it. Also set the requested speed settings in set_settings in
ethtool as they are requested and initialize them in probe based on what
the firmware remembers as the last requested speeds.
To accommodate some longer lines in this new code, and improve
readability I have added two functions i40e_get_settings_link_up
and i40e_get_settings_link_down which get_settings now calls first.
It then does all of the settings that happen regardless of link
state. Some PHY types that supported the same settings were also combined.
Also update the copyright year.
Change-ID: Ica0c5ac81b6069ea6a7406fce7482f7816d4455c
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_debug_aq() prints information helpful in debugging
admin queue commands, but it doesn't do so correctly on big endian machines.
This patch adds the appropriate LExx_TO_CPU wrappers for big endian
architectures.
Also update the copyright year.
Change-ID: I4b2dc229ed5bf6dfe35632a58cddf53c21aff4b0
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent change to bitmap_create mishandles errors.
In particular a failure doesn't alway cause 'err' to be set.
Signed-off-by: NeilBrown <neilb@suse.de>
Since __ATTR_PREALLOC was introduced in v3.19-rc1~78^2~18
it can now be used by md.
This ensure that writing to these sysfs attributes will never
block due to a memory allocation.
Such blocking could become a deadlock if mdmon is trying to
reconfigure an array after a failure prior to re-enabling writes.
Signed-off-by: NeilBrown <neilb@suse.de>
When we have more than 1 drive failure, it's possible we start
rebuild one drive while leaving another faulty drive in array.
To determine whether array will be optimal after building, current
code only check whether a drive is missing, which could potentially
lead to data corruption. This patch is to add checking Faulty flag.
Signed-off-by: NeilBrown <neilb@suse.de>
When a drive is marked write-mostly it should only be the
target of reads if there is no other option.
This behaviour was broken by
commit 9dedf60313
md/raid1: read balance chooses idlest disk for SSD
which causes a write-mostly device to be *preferred* is some cases.
Restore correct behaviour by checking and setting
best_dist_disk and best_pending_disk rather than best_disk.
We only need to test one of these as they are both changed
from -1 or >=0 at the same time.
As we leave min_pending and best_dist unchanged, any non-write-mostly
device will appear better than the write-mostly device.
Reported-by: Tomáš Hodek <tomas.hodek@volny.cz>
Reported-by: Dark Penguin <darkpenguin@yandex.ru>
Signed-off-by: NeilBrown <neilb@suse.de>
Link: http://marc.info/?l=linux-raid&m=135982797322422
Fixes: 9dedf60313
Cc: stable@vger.kernel.org (3.6+)
When printing the driver_override parameter when it is 4095 and 4094 bytes
long, the printing code would access invalid memory because we need count+1
bytes for printing.
Fixes: 782a985d7a ("PCI: Introduce new device binding path using pci_dev.driver_override")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
CC: stable@vger.kernel.org # v3.16+
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Alexander Graf <agraf@suse.de>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl error:
space prohibited before that ','
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl errors for
the file fb_bd663474.c:
ERROR: space prohibited before that close parenthesis ')'
ERROR: space prohibited after that open parenthesis '('
ERROR: space required after that ','
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses the checkpatch.pl warning
WARNING: __aligned(size) is preferred over __attribute__((aligned(size)))
aligned(x) is a macro :
#define __aligned(x) __attribute__((aligned(x)))
Signed-off-by: Vatika Harlalka <vatikaharlalka@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid deadlock, do not call blocking functions with spinlocks held.
Replace GFP_KERNEL with GFP_ATOMIC, as the latter will fail if the pile
doesn't have enough free pages but will not sleep and hence deadlock can
be avoided.
Found by Coccinelle.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Byte Queue Limits (BQL) support to via-rhine driver.
[edumazet] tweaked patch and changed TX_RING_SIZE from 16 to 64
Signed-off-by: Tino Reichardt <milky-kernel@mcmilk.de>
Tested-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the pending indexes are released /after/ pushing the Tx response
then a stale pending index may be used if a new Tx request is
immediately pushed by the frontend. The may cause various WARNINGs or
BUGs if the stale pending index is actually still in use.
Fix this by releasing the pending index before pushing the Tx
response.
The full barrier for the pending ring update is not required since the
the Tx response push already has a suitable write barrier.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Churn Detection machines detect the situation where a port is operable,
but the Actor and Partner have not attached the link to an Aggregator and
brought the link into operation within a bound time period. Under normal
operation of the LACP, agreement between Actor and Partner should be reached
very rapidly. Continued failure to reach agreement can be symptomatic of
device failure.
Actor-churn-detection state-machine
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
===================================
BEGIN=True + PortEnable=False
|
v
+------------------------+ ActorPort.Sync=True +------------------+
| ACTOR_CHURN_MONITOR | ---------------------> | NO_ACTOR_CHURN |
|========================| |==================|
| ActorChurn=False | ActorPort.Sync=False | ActorChurn=False |
| ActorChurn.Timer=Start | <--------------------- | |
+------------------------+ +------------------+
| ^
| |
ActorChurn.Timer=Expired |
| ActorPort.Sync=True
| |
| +-----------------+ |
| | ACTOR_CHURN | |
| |=================| |
+--------------> | ActorChurn=True | ------------+
| |
+-----------------+
Similar for the Partner-churn-detection.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.1AX standard states:
"The DA in LACPDUs is the Slow_Protocols_Multicast address."
This patch enforces that and drops LACPDUs with destination MAC
addresses other than Slow_Protocols_Multicast address
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I overlooked the fact that we need to allocate a minimum 8 blocks and
that just allocating the planes depending on how much they need to fetch
from the DDB in proportion of how much memory bw is necessary for the
whole display can lead to cases where we don't respect those minima (and
thus overrun).
So, instead, start by allocating 8 blocks to each active display plane
and then allocate the remaining blocks like before.
v2: Rebase on top of -nightly
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The HID over I2C specification allows to have the interrupt for a HID
device to be GPIO instead of directly connected to the IO-APIC.
Add support for this so that when the driver does not find proper interrupt
number from the I2C client structure we check if it has ACPI GpioInt()
resource listed in _CRS. If it is found we convert it to an interrupt
number and use it instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>