pwm_get_period() is called twice in case the child parameter is set. I
assume retrieving this parameter once is enough therefore this patch
removes the conditial invocation of pwm_get_period().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Swap interrupt disable and thermal zone unregistration in the error and
remove paths, to make them more symmetrical with the initialization
path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As soon as the interrupt has been enabled by devm_request_irq(), the
interrupt routine may be called, depending on the current status of the
hardware.
However, at that point rcar_thermal_common hasn't been initialized
complely yet. E.g. rcar_thermal_common.base is still NULL, causing a
NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
pgd = c0004000
[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc7-ape6evm-04564-gb6e46cb7cbe82389 #30
Hardware name: Generic R8A73A4 (Flattened Device Tree)
task: ee8953c0 ti: ee896000 task.ti: ee896000
PC is at rcar_thermal_irq+0x1c/0xf0
LR is at _raw_spin_lock_irqsave+0x48/0x54
Postpone the call to devm_request_irq() until all initialization has
been done to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
According to SMBIOSv3 specification the length of DMI table can be
up to 32bits wide. So use appropriate type to avoid overflow.
It's obvious that dmi_num theoretically can be more than u16 also,
so it's can be changed to u32 or at least it's better to use int
instead of u16, but on that moment I cannot imagine dmi structure
count more than 65535 and it can require changing type of vars that
work with it. So I didn't correct it.
Acked-by: Ard Biesheuvel <ard@linaro.org>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
While adding support loading kernel and initrd above 4G to grub2 in legacy
mode, I was referring to efi_high_alloc().
That will allocate buffer for kernel and then initrd, and initrd will
use kernel buffer start as limit.
During testing found two buffers will be overlapped when initrd size is
very big like 400M.
It turns out efi_high_alloc() boundary checking is not right.
end - size will be the new start, and should not compare new
start with max, we need to make sure end is smaller than max.
[ Basically, with the current efi_high_alloc() code it's possible to
allocate memory above 'max', because efi_high_alloc() doesn't check
that the tail of the allocation is below 'max'.
If you have an EFI memory map with a single entry that looks like so,
[0xc0000000-0xc0004000]
And want to allocate 0x3000 bytes below 0xc0003000 the current code
will allocate [0xc0001000-0xc0004000], not [0xc0000000-0xc0003000]
like you would expect. - Matt ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The cpufreq_cooling_unregister() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Fix following build warning if CONFIG_PM_SLEEP is not set:
drivers/thermal/ti-soc-thermal/ti-bandgap.c:1478:12: warning: 'ti_bandgap_suspend' defined but not used [-Wunused-function]
static int ti_bandgap_suspend(struct device *dev)
^
drivers/thermal/ti-soc-thermal/ti-bandgap.c:1492:12: warning: 'ti_bandgap_resume' defined but not used [-Wunused-function]
static int ti_bandgap_resume(struct device *dev)
^
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
- Fix two regression introduced in 4.0-rc1 affecting PV/PVH guests in
certain configurations.
- Prevent pvscsi frontends bypassing backend checks.
- Allow privcmd hypercalls to be preempted even on kernel with
voluntary preemption. This fixes soft-lockups with long running
toolstack hypercalls (e.g., when creating/destroying large domains).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJU7GDMAAoJEFxbo/MsZsTRj7AIAIFD2Dgu9p56nx6rUA6JOWP9
2O1VlINEkggUFNCekTJ3HkAjHreC2Ir67nk1PTTfL3ZN+PqxEv+IoUF1XKJxE/G3
0KchszK0MVnc7UBrUJWRUEpGo92iIC9QBc8MyDN6dGbfV5lT4aHB5ug/aSZqG8HV
8ITOftfwnVE8ukOK9bSRPZRejnoRMbGUmqpr0X17sE4Zb8+LEf0iO5Yh88NEjzxM
OD5hL3TGN5uXh6rYHS+U82M1g83G4Q7v10WIN5O96QhA6e5rVbVNsohHpL8IHY5q
kazw7wBY//SKGCGniACYnh+vZDeNddwCz8chj6S49h272zanMleyolrUjlcMGzQ=
=xmcy
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-4.0-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bugfixes from David Vrabel:
"Xen regression and bug fixes for 4.0-rc1
- Fix two regressions introduced in 4.0-rc1 affecting PV/PVH guests
in certain configurations.
- Prevent pvscsi frontends bypassing backend checks.
- Allow privcmd hypercalls to be preempted even on kernel with
voluntary preemption. This fixes soft-lockups with long running
toolstack hypercalls (e.g., when creating/destroying large
domains)"
* tag 'stable/for-linus-4.0-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: Initialize cr4 shadow for 64-bit PV(H) guests
xen-scsiback: mark pvscsi frontend request consumed only after last read
x86/xen: allow privcmd hypercalls to be preempted
x86/xen: Make sure X2APIC_ENABLE bit of MSR_IA32_APICBASE is not set
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-23
This series contains updates to e1000e, igbvf, i40e and i40evf.
David adds support for i219 devices to the e1000e driver.
Jeff (me) provides two patches to cleanup igbvf, first cleans up the
whitespace issues found and the second cleans up the usage of msleep(),
min() and max() with usleep_range(), min_t() and max_t() respectively.
Kamil updates the shadow RAM read/write functions by refactoring them
to prepare for future work.
Shannon renames the debugfs command "clear_stats pf" to clear_stats port"
to clarify what the function really does.
Mitch refactors the receive routine, by splitting the receive hot path
code into two, one for packet split and one for single buffer, which
improves receive performance. Disables NAPI polling sooner when closing
the interface to fix an occasional panic during close which was
caused by the driver trying to delete and clean rings at the same time.
Also refactors reset for i40evf, since a recent change to the shutdown
flow messed up the reset flow. Since i40evf_down() now holds the
critical section lock, we cannot call it from the reset handler, which
also holds the lock.
Nicholas restricts the virtual channel opcodes should remain consistent
between updates to the opcode enum.
Neerav converts the VSI connection type to use a #define instead of
using a magic number.
Anjali updates the registers file to remove registers no longer available.
Also fixes the EMPR interrupt handling, so that we won't trigger another
EMPR when we receive an EMPR event.
Catherine cleans up the variable an_enable since it was set and never
used.
Greg fixes the netdev op that allows the operator to turn MAC/VLAN
spoof checking on and off so that it includes the flag for VLAN spoof
checking.
v2: Updated patch #10 in the series to use test_and_clear_bit() as
suggested by Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_hw_params->bds_cnt and GENET_DEFAULT_BD_CNT are used only in Tx init.
Rename them accordingly:
- bcmgenet_hw_params->bds_cnt => bcmgenet_hw_params->tx_bds_per_q
- GENET_DEFAULT_BD_CNT => GENET_Q16_TX_BD_CNT
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is 1-to-1 mapping between TxCBs and TxBDs. Precalculate TxCB->bd_addr
once in bcmgenet_init_dma() instead of doing it over and over needlessly in
bcmgenet_get_txcb().
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Rename bcmgenet_init_multiq() to bcmgenet_init_tx_queues()
2. Fix bcmgenet_init_tx_queues() function description
3. Move Tx default queue init inside bcmgenet_init_tx_queues()
4. Modify bcmgenet_init_dma() to call bcmgenet_init_tx_queues()
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Simplify function description
2. Rename function parameter write_ptr to start_ptr to better indicate use
3. Remove unnecessary local variable first_bd
4. Remove out-of-place comment "Unclassified traffic goes to ring 16"
5. Fix TDMA_WRITE_PTR register init
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support an older USB cradle by Denso, I added its vendor- and product-ID to the array of usb_device_id acm_ids. In this way cdc-acm feels responsible for this cradle. The related /dev/ttyACM node is being created properly, and the data transfer works.
However, later cradle models by Denso do have proper descriptors, so the patch is not required for these. At the same time both the older and the later model have the same vendor- and product-ID, but they both work with the patched driver.
Declaration of the Denso cradles I tested:
- both models have the same IDs: vendorID 0x076d, productID 0x0006
- older model: Denso CU-321 (descriptors not properly set)
- later model: Denso CU-821 (with proper descriptors)
Signed-off-by: Bjoern Gerhart <oss@airbjorn.de>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is necessary to make some storage arrays work.
Some storage devices have more than 8 LUNs. In addition
you can hook up a WideSCSI bus to USB. In these cases even
level 2 devices can have more than 8 LUNs. For them
it is necessary to simply believe the class specific
command and report its result back to the SCSI layer.
Off by one Alan noticed is fixed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the JMicron JMS567 enclosures with the JMS539 choke on report-opcodes,
so avoid it.
Tested-and-reported-by: Tom Arild Naess <tanaess@gmail.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a signal is delivered, the information in the siginfo structure
is copied to userspace. Good security practice dicatates that the
unused fields in this structure should be initialized to 0 so that
random kernel stack data isn't exposed to the user. This patch adds
such an initialization to the two places where usbfs raises signals.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dave Mielke <dave@mielke.cc>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Main benefit of this is to get xhci connected USB scanners to work.
Some devices use a clear endpoint halt request as a 'soft reset' even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side. xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host side
toggle and sequence, and get it in sync with the device side.
Tested-by: Mike Mammarella <mikem@crystalorb.net>
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the high order bit fields for Max scratchpad buffers when
calculating how many scratchpad buffers are needed.
I'm suprised this hasn't caused more issues, we never allocated more than
32 buffers even if xhci needed more. Either we got lucky and xhci never
really used past that area, or then we got enough zeroed dma memory anyway.
Should be backported as far back as possible
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 9737479285 ("usb: host: xhci-plat: add support for the Armada
375/38x XHCI controllers") extended the xhci-plat driver to support the Armada
375/38x SoCs, mostly by adding a quirk configuring the MBUS window.
However, that quirk was run before the clock the controllers needs has been
enabled. This usually worked because the clock was first enabled by the
bootloader, and left as such until the driver is probe, where it tries to
access the MBUS configuration registers before enabling the clock.
Things get messy when EPROBE_DEFER is involved during the probe, since as part
of its error path, the driver will rightfully disable the clock. When the
driver will be reprobed, it will retry to access the MBUS registers, but this
time with the clock disabled, which hangs forever.
Fix this by running the quirks after the clock has been enabled by the driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull HID fixes from Jiri Kosina:
- a few fixes to Sony driver (rmmod breakage, spinlock initialization),
by Antonio Ospite, Frank Praznik and Jiri Kosina
- fix for wMaxInputLength handling regression in i2c-hid, by Seth
Forshee
- IRQ safety spinlock fix in sensor hub driver, by Srinivas Pandruvada
- IRQ level sensitivity fix to i2c-hid to be compliant with the spec,
by Mika Westerberg
- a couple device ID additions piggy-backing on top of that
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: microsoft: Add ID for NE7K wireless keyboard
HID: i2c-hid: Limit reads to wMaxInputLength bytes for input events
HID: sony: fix uninitialized per-controller spinlock
HID: sony: initialize sony_dev_list_lock properly
HID: sony: Fix a WARNING shown when rmmod-ing the driver
HID: sensor-hub: correct dyn_callback_lock IRQ-safe change
HID: hid-sensor-hub: Correct documentation
HID: saitek: add USB ID for older R.A.T. 7
HID: i2c-hid: The interrupt should be level sensitive
HID: wacom: Add missing ABS_MISC event and feature declaration for 27QHD
Instead of an additional reading from the register let's update it even if the
value is kept the same.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch does the following changes:
a) the calculation of clk_div is simplified to oneliner;
b) chip->clk_div is updated if clk_div is not zero, therefore the condition is
simplified by using chip->clk_div in both cases;
c) while here, the redundant parentheses are removed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to have an additional variable to get a TX level. The patch
refactors this piece of code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no sense to keep a member assignment in the internal structure inside
the condition which reprograms HW. It makes code readability better if kept
outside of the condition.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some bios really like to joke and start the planes at an offset ...
hooray!
Align start and end to fix this.
v2: Fixup calculation of size, spotted by Chris Wilson.
v3: Fix serious fumble I've just spotted.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86883
Cc: stable@vger.kernel.org
Cc: Johannes W <jargon@molb.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reported-and-tested-by: Johannes W <jargon@molb.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[Jani: split WARN_ONs, rebase on v4.0-rc1]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atm, it's possible that the interrupt handler is called when the device
is in D3 or some other low-power state. It can be due to another device
that is still in D0 state and shares the interrupt line with i915, or on
some platforms there could be spurious interrupts even without sharing
the interrupt line. The latter case was reported by Klaus Ethgen using a
Lenovo x61p machine (gen 4). He noticed this issue via a system
suspend/resume hang and bisected it to the following commit:
commit e11aa36230
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Jun 18 09:52:55 2014 -0700
drm/i915: use runtime irq suspend/resume in freeze/thaw
This is a problem, since in low-power states IIR will always read
0xffffffff resulting in an endless IRQ servicing loop.
Fix this by handling interrupts only when the driver explicitly enables
them and so it's guaranteed that the interrupt registers return a valid
value.
Note that this issue existed even before the above commit, since during
runtime suspend/resume we never unregistered the handler.
v2:
- clarify the purpose of smp_mb() vs. synchronize_irq() in the
code comment (Chris)
v3:
- no need for an explicit smp_mb(), we can assume that synchronize_irq()
and the mmio read/writes in the install hooks provide for this (Daniel)
- remove code comment as the remaining synchronize_irq() is self
explanatory (Daniel)
v4:
- drm_irq_uninstall() implies synchronize_irq(), so no need to call it
explicitly (Daniel)
Reference: https://lkml.org/lkml/2015/2/11/205
Reported-and-bisected-by: Klaus Ethgen <Klaus@Ethgen.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we walk the list of vma, or even for protecting against concurrent
framebuffer creation, we must hold the struct_mutex or else a second
thread can corrupt the list as we walk it.
Fixes regression from
commit d7f46fc4e7
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Fri Dec 6 14:10:55 2013 -0800
drm/i915: Make pin count per VMA
References: https://bugs.freedesktop.org/show_bug.cgi?id=89085
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When converting from implicitly tracked execlist queue items to ref counted
requests, not all frees of requests were replaced with unrefs, and extraneous
refs/unrefs of contexts were added.
Correct the unbalanced refcount & replace the frees.
Remove a noisy warning when hitting the request creation path.
drm_i915_gem_request and intel_context are both kref reference counted
structures. Upon allocation, drm_i915_gem_request's ref count should be
bumped using kref_init. When a context is assigned to the request,
the context's reference count should be bumped using i915_gem_context_reference.
i915_gem_request_reference will reduce the context reference count when
the request is freed.
Problem introduced in
commit 6d3d8274bc
Author: Nick Hoath <nicholas.hoath@intel.com>
AuthorDate: Thu Jan 15 13:10:39 2015 +0000
drm/i915: Subsume intel_ctx_submit_request in to drm_i915_gem_request
v2: Added comments explaining how the ctx pointer and the request object should
be ref-counted. Removed noisy warning.
v3: Cleaned up the language used in the commit & the header
description (Thanks David Gordon)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88652
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When Downclock mode is not found, the same info is added to the
corresponding debug log.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding an overview of DRRS in general and the implementation for eDP DRRS.
Also, describing the functions related to eDP DRRS.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch enables eDP DRRS for CHV by adding the
required IS_CHERRYVIEW() checks.
CHV uses the same register bit as VLV.
[Vandana]: Since CHV has 2 sets of M_N registers, it will follow the same code
path as gen < 8. Added CHV check in dp_set_m_n()
[Ram]: Rebased on top of previous patch modifications
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Definition of VLV RR switch bit and corresponding toggling in
set_drrs function.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Broadwell, there is one instance of Transcoder MN values per transcoder.
For dynamic switching between multiple refreshr rates, M/N values may be
reprogrammed on the fly. Link N programming triggers update of all data and
link M & N registers and the new M/N values will be used in the next frame
that is output.
V2: [By Ram]: intel_dp_set_m_n() is rewritten to accommodate
gen >= 8 [Rodrigo]
V3: Coding style correction [Ram]
V4: [By Ram] intel_dp_set_m_n modifications are moved into a
separate patch, retaining only DRRS related changes here [Rodrigo]
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Till Gen 7 we have two sets of M_N registers, but Gen 8 onwards
we have only one M_N register set. To support DRRS on both scenarios
a input parameter to intel_dp_set_m_n is added.
In case of DRRS, When platform provides two set of M_N registers for dp,
we can program them with two different dividers and switch between them.
But when only one such register set is provided, we have to program
the required divider M_N value on that registers itself.
Two enum members M1_N1 and M2_N2 are defined to represent the above
scenarios.
M1_N1 : Program dp_m_n on M1_N1 registers
dp_m2_n2 on M2_N2 registers (If supported)
M2_N2 : Program dp_m2_n2 on M1_N1 registers
M2_N2 registers are not supported
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As of Gen6, the general purpose area of the hardware status page has shrunk and
now begins at dword 0x30. i915 driver uses dword 0x20 to store the seqno which
is now reserved. So shift our HWSP dwords up into the general purpose range
before this bites us.
Note that all available documentation just says this is reserved
without going into details about what it's used for.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
[danvet: Add clarification from Thomas that unfortunately Bspec is
silent on what "reserverd" precisely means.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove a useless pm_runtime_put_sync leading to unbalanced
usage_count.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
The A2Q (Add To Queue) and UPDATE bits are left in their previous state
when resetting the layer.
This lead to weird behavior when enabling the plane again: the framebuffer
previously queued is dequeued and we end up with access to an old memory
region.
Reset those bits when resetting the channel.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Lenovo Thinkpad 10 has wacom digitizer connected as a I2C-HID device. Add
generic support for this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some LCD panels have back-powering issue when un-powered, allows users
to use an alternate pinctrl "sleep" in order to clamp outputs to a
wanted state at suspend.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
On suspend: switch off CRTC if not already suspended with runtime PM
On resume: switch on CRTC if we were not already suspended from runtime
PM while suspending.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Correct two problems with the error handling when using the netlink
forwarding API: first, the netlink skb is never freed if nla_put()
fails; and second, genlmsg_unicast() can fail if the netlink socket
is full. In the latter case, the corresponding data skb is not counted
as a drop and userspace programs like wmediumd will see TCP stalls
due to lost packets.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to the documentation, no data is passed with the OVER_CURRENT
regulator notifier event.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We tried to read the CONFIG_E register, not the CONTROL_E register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The seq_puts/seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Miscellanea:
o Remove unnecessary dev_err("seq_<foo> overflow\n") messages
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the documentation, no data is passed with the
REGULATION_OUT and UNDER_VOLTAGE regulator notifier events.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit d58cf5ff65 brought a second controller to the list of supported
devices and changed a number of the chip selects. Besides the previous number
was wrong anyway the mentioned patch makes it wrong again meanwhile has a
proper numbers in the commit message. Indeed, SPI1 has 5 bits and SPI2 has 2
bits, but it does not mean to have power of two of this bits as a possible
number of the chip selects. So, this patch fixes it eventually.
Fixes: d58cf5ff65 (spi: dw-pci: describe Intel MID controllers better)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Ensures that block2mtd is triggered after the block devices are enumerated
at boot time.
This issue is seen on BCM2835 (Raspberry Pi) systems when mounting JFFS2
block2mtd filesystems, probably because of the delay on enumerating a USB
MMC card reader.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rodrigo Freire <rfreire@redhat.com>
Signed-off-by: Herton Krzesinski <herton@redhat.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The lower 16 bits of the address, which is managed by mem_res, need to be
zero. Check the address to verify this.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>