commit f2d580b9a8 upstream.
It turns out that preserving framebuffers after the rmfb call breaks
vmwgfx userspace. This was originally introduced because it was thought
nobody relied on the behavior, but unfortunately it seems there are
exceptions.
drm_framebuffer_remove may fail with -EINTR now, so a straight revert
is impossible. There is no way to remove the framebuffer from the lists
and active planes without introducing a race because of the different
locking requirements. Instead call drm_framebuffer_remove from a
workqueue, which is unaffected by signals.
Changes since v1:
- Add comment.
Changes since v2:
- Add fastpath for refcount = 1. (danvet)
Changes since v3:
- Rebased.
- Restore lastclose framebuffer removal too.
Fixes: 1380313281 ("drm/core: Preserve the framebuffer after removing it.")
Testcase: kms_rmfb_basic
References: https://lists.freedesktop.org/archives/dri-devel/2016-March/102876.html
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Thomas Hellstrom <thellstrom@vmware.com> #v3
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/6c63ca37-0e7e-ac7f-a6d2-c7822e3d611f@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5edf673d07 upstream.
When a dual-edge irq is triggered, an incorrect irq will be reported on
condition that the external signal is not stable and this incorrect irq
has been registered.
Correct the register offset.
Signed-off-by: Hongkun Cao <hongkun.cao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab6a11a7c8 upstream.
The ccp-crypto module for AES XTS support has a bug that can allow requests
greater than 4096 bytes in size to be passed to the CCP hardware. The CCP
hardware does not support request sizes larger than 4096, resulting in
incorrect output. The request should actually be handled by the fallback
mechanism instantiated by the ccp-crypto module.
Add a check to insure the request size is less than or equal to the maximum
supported size and use the fallback mechanism if it is not.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b66b2a0adf upstream.
The bcm_kona_gpio_reset() calls bcm_kona_gpio_write_lock_regs()
with what looks like the wrong parameter. The write_lock_regs
function takes a pointer to the registers, not the bcm_kona_gpio
structure.
Fix the warning, and probably bug by changing the function to
pass reg_base instead of kona_gpio, fixing the following warning:
drivers/gpio/gpio-bcm-kona.c:550:47: warning: incorrect type in argument 1
(different address spaces)
expected void [noderef] <asn:2>*reg_base
got struct bcm_kona_gpio *kona_gpio
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:2>*reg_base
got struct bcm_kona_gpio *kona_gpio
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e059158d5 ]
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 55e5bfb53c ]
Allow the MTU of geneve devices to be set to large values, in order to
exploit underlying networks with larger frame sizes.
GENEVE does not have a fixed encapsulation overhead (an openvswitch
rule can add variable length options), so there is no relevant maximum
MTU to enforce. A maximum of IP_MAX_MTU is used instead.
Encapsulated packets that are too big for the underlying network will
get dropped on the floor.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 72564b59ff ]
Allow the MTU of vxlan devices without an underlying device to be set
to larger values (up to a maximum based on IP packet limits and vxlan
overhead).
Previously, their MTUs could not be set to higher than the
conventional ethernet value of 1500. This is a very arbitrary value
in the context of vxlan, and prevented vxlan devices from being able
to take advantage of jumbo frames etc.
The default MTU remains 1500, for compatibility.
Signed-off-by: David Wragg <david@weave.works>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce577668a4 ]
When create a new vxlan link, example:
ip link add vtap mtu 1440 type vxlan vni 1 dev eth0
The argument "mtu" has no effect, because it is not set to conf->mtu. The
default value is used in vxlan_dev_configure function.
This problem was introduced by commit 0dfbdf4102 (vxlan: Factor out device
configuration).
Fixes: 0dfbdf4102 (vxlan: Factor out device configuration)
Signed-off-by: Chen Haiquan <oc@yunify.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6988cb63a ]
The team_device_event() notifier calls team_compute_features() to fix
vlan_features under team->lock to protect team->port_list. The problem is
that subsequent __team_compute_features() calls netdev_change_features()
to propagate vlan_features to upper vlan devices while team->lock is still
taken. This can lead to deadlock when NETIF_F_LRO is modified on lower
devices or team device itself.
Example:
The team0 as active backup with eth0 and eth1 NICs. Both eth0 & eth1 are
LRO capable and LRO is enabled. Thus LRO is also enabled on team0.
The command 'ethtool -K team0 lro off' now hangs due to this deadlock:
dev_ethtool()
-> ethtool_set_features()
-> __netdev_update_features(team)
-> netdev_sync_lower_features()
-> netdev_update_features(lower_1)
-> __netdev_update_features(lower_1)
-> netdev_features_change(lower_1)
-> call_netdevice_notifiers(...)
-> team_device_event(lower_1)
-> team_compute_features(team) [TAKES team->lock]
-> netdev_change_features(team)
-> __netdev_update_features(team)
-> netdev_sync_lower_features()
-> netdev_update_features(lower_2)
-> __netdev_update_features(lower_2)
-> netdev_features_change(lower_2)
-> call_netdevice_notifiers(...)
-> team_device_event(lower_2)
-> team_compute_features(team) [DEADLOCK]
The bug is present in team from the beginning but it appeared after the commit
fd867d5 (net/core: generic support for disabling netdev features down stack)
that adds synchronization of features with lower devices.
Fixes: fd867d5 (net/core: generic support for disabling netdev features down stack)
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0795bf64c ]
Otherwise, if we fail to allocate new PIO buffers, our TXQs will try to
use the old ones, which aren't there any more.
Fixes: 183233bec8 "sfc: Allocate and link PIO buffers; map them with write-combining"
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e5aed006be ]
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit addf8fc4ac ]
We used to check dev->reg_state against NETREG_REGISTERED after each
time we are woke up. But after commit 9e641bdcfa ("net-tun:
restructure tun_do_read for better sleep/wakeup efficiency"), it uses
skb_recv_datagram() which does not check dev->reg_state. This will
result if we delete a tun/tap device after a process is blocked in the
reading. The device will wait for the reference count which was held
by that process for ever.
Fixes this by using RCV_SHUTDOWN which will be checked during
sk_recv_datagram() before trying to wake up the process during uninit.
Fixes: 9e641bdcfa ("net-tun: restructure tun_do_read for better
sleep/wakeup efficiency")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Xi Wang <xii@google.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da4ed55165 ]
The problem is that fib_info->nh is [0] so the struct fib_info
allocation size depends on number of nexthops. If we just copy fib_info,
we do not copy the nexthops info and driver accesses memory which is not
ours.
Given the fact that fib4 does not defer operations and therefore it does
not need copy, just pass the pointer down to drivers as it was done
before.
Fixes: 850d0cbc91 ("switchdev: remove pointers from switchdev objects")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a621bac304 upstream.
When SCSI was written, all commands coming from the filesystem
(REQ_TYPE_FS commands) had data. This meant that our signal for needing
to complete the command was the number of bytes completed being equal to
the number of bytes in the request. Unfortunately, with the advent of
flush barriers, we can now get zero length REQ_TYPE_FS commands, which
confuse this logic because they satisfy the condition every time. This
means they never get retried even for retryable conditions, like UNIT
ATTENTION because we complete them early assuming they're done. Fix
this by special casing the early completion condition to recognise zero
length commands with errors and let them drop through to the retry code.
Reported-by: Sebastian Parschauer <s.parschauer@gmx.de>
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Tested-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a17fb329d upstream.
Grygorii Strashko reports:
The PM runtime will be left disabled for the device if its
.suspend_late() callback fails and async suspend is not allowed
for this device. In this case device will not be added in
dpm_late_early_list and dpm_resume_early() will ignore this
device, as result PM runtime will be disabled for it forever
(side effect: after 8 subsequent failures for the same device
the PM runtime will be reenabled due to disable_depth overflow).
To fix this problem, add devices to dpm_late_early_list regardless
of whether or not device_suspend_late() returns errors for them.
That will ensure failures in there to be handled consistently for
all devices regardless of their async suspend/resume status.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 310944d148 upstream.
The component master driver imx-drm-core matches component devices using
their of_node. Since commit 950b410dd1ab ("gpu: ipu-v3: Fix imx-ipuv3-crtc
module autoloading"), the imx-ipuv3-crtc dev->of_node is not set during
probing. Before that, of_node was set and caused an of: modalias to be
used instead of the platform: modalias, which broke module autoloading.
On the other hand, if dev->of_node is not set yet when the imx-ipuv3-crtc
probe function calls component_add, component matching in imx-drm-core
fails. While dev->of_node will be set once the next component tries to
bring up the component master, imx-drm-core component binding will never
succeed if one of the crtc devices is probed last.
Add of_node to the component platform data and match against the
pdata->of_node instead of dev->of_node in imx-drm-core to work around
this problem.
Fixes: 950b410dd1ab ("gpu: ipu-v3: Fix imx-ipuv3-crtc module autoloading")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7045c3689f upstream.
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9 ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 15606534bf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately since we don't have Dave's connector refcounting patch
here yet, it's very possible that drm_atomic_state_default_clear() could
get called by intel_display_resume() when
intel_dp_mst_destroy_connector() isn't completely finished destroying an
mst connector, but has already finished setting connector->funcs to
NULL. As such, we need to treat the connector like it's already been
destroyed and just skip it, otherwise we'll end up dereferencing a NULL
pointer.
This fix is only required for 4.6 and below. David Airlie's patchseries
for 4.7 to add connector reference counting provides a more proper fix
for this.
Changes since v1:
- Fix leftover whitespace
Upstream fix: 0552f7651b ("drm/i915/mst: use reference counted
connectors. (v3)")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
commit 255f0e7c41 upstream.
During boot, MST hotplugs are generally expected (even if no physical
hotplugging occurs) and result in DRM's connector topology changing.
This means that using num_connector from the current mode configuration
can lead to the number of connectors changing under us. This can lead to
some nasty scenarios in fbcon:
- We allocate an array to the size of dev->mode_config.num_connectors.
- MST hotplug occurs, dev->mode_config.num_connectors gets incremented.
- We try to loop through each element in the array using the new value
of dev->mode_config.num_connectors, and end up going out of bounds
since dev->mode_config.num_connectors is now larger then the array we
allocated.
fb_helper->connector_count however, will always remain consistent while
we do a modeset in fb_helper.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this. Also remove the now unused "dev"
local variable to appease gcc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-3-git-send-email-cpaul@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14a3842a1d upstream.
During boot time, MST devices usually send a ton of hotplug events
irregardless of whether or not any physical hotplugs actually occurred.
Hotplugs mean connectors being created/destroyed, and the number of DRM
connectors changing under us. This isn't a problem if we use
fb_helper->connector_count since we only set it once in the code,
however if we use num_connector from struct drm_mode_config we risk it's
value changing under us. On top of that, there's even a chance that
dev->mode_config.num_connector != fb_helper->connector_count. If the
number of connectors happens to increase under us, we'll end up using
the wrong array size for memcpy and start writing beyond the actual
length of the array, occasionally resulting in kernel panics.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-2-git-send-email-cpaul@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d746ab681 upstream.
When porting the hdmi deep color detection code from
radeon-kms to amdgpu-kms apparently some kind of
copy and paste error happened, attaching an else
branch to the wrong if statement.
The result is that hdmi deep color mode is always
disabled, regardless of gpu and display capabilities and
user wishes, as the code mistakenly thinks that the display
doesn't provide the required max_tmds_clock limit and falls
back to 8 bpc.
This patch fixes deep color support, as tested on a
R9 380 Tonga Pro + suitable display, and should be
backported to all kernels with amdgpu-kms support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b8812eb00 upstream.
This is a port of radeon commit:
3d2d98ee1a
drm/radeon: use drm_mode_vrefresh() rather than mode->vrefresh
to amdgpu.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7851496a32 upstream.
mode->hdisplay * (var->bits_per_pixel + 7) gets evaluated before
the division, potentially making the pitch larger than it should
be.
Since the original intention is to do a div-round-up, just use
the macro instead.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e02e588431 upstream.
Instead of calling vmw_cmd_ok, call vmw_cmd_dx_cid_check to
validate the context id for query commands.
Signed-off-by: Charmaine Lee <charmainel@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ccca1d5bf upstream.
Fix possible out of bounds read, by adding missing comma.
The code may read pass the end of the dsi_errors array
when the most significant bit (bit #31) in the intr_stat register
is set.
This bug has been detected using CppCheck (static analysis tool).
Signed-off-by: Itai Handler <itai_handler@hotmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11ca2b7ab4 upstream.
New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart.
So add it.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baf43c6eac upstream.
In v4l2-compliance utility, test VIDIOC_CREATE_BUFS will check whether reserved
filed of v4l2_create_buffers filled with zero
Reserved field is filled with zero in v4l_create_bufs.
This patch copy reserved field of v4l2_create_buffer from kernel space to user
space
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad67b437f1 upstream.
b84106b4e2 ("PCI: Disable IO/MEM decoding for devices with non-compliant
BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with
the PCI spec. But it didn't do anything for expansion ROM BARs, so we
still try to size them, resulting in warnings like this on Broadwell-EP:
pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref]
Move the non-compliant BAR check from __pci_read_base() up to
pci_read_bases() so it applies to the expansion ROM BAR as well as
to BARs 0-5.
Note that direct callers of __pci_read_base(), like sriov_init(), will now
bypass this check. We haven't had reports of devices with broken SR-IOV
BARs yet.
[bhelgaas: changelog]
Fixes: b84106b4e2 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71324fdc72 upstream.
The range is registered into a linked list which can be referenced
throughout the lifetime of the driver. Ensure the range's memory is useful
for the same lifetime by adding it to the driver's private data structure.
The bug was introduced in the driver's initial commit, which was present in
v3.10.
Fixes: f0b9a7e521 ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 997f16bd5d upstream.
Current clamping of a normal divider allows a value < 1 to be valid.
A divider of < 1 would actually only be possible if we had a PLL...
So this patch clamps the divider to 1.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6727f086cf upstream.
bcm2835_pll_off is currently assigning CM_PLL_ANARST to the control
register, which may lose the other bits that are currently set by the
clock dividers.
It also now locks during the read/modify/write cycle of both
registers.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb0ceaf77d upstream.
The clk_register() function returns a valid pointer to struct clk or
ERR_PTR() error code, this makes a check for returned NULL value
useless and may lead to oops on error path.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: bcc5fd49a0 ("clk: at91: add a driver for the h32mx clock")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e708b383f4 upstream.
In poweroff, we set the reset bit and the power down bit, but only
managed to unset the reset bit for poweron. This meant that if HDMI
did -EPROBE_DEFER after it had grabbed its clocks, we'd power down the
PLLH (that had been on at boot time) and never recover.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7387da520 upstream.
Commit 0b89e9aa28 (cpuidle: delay enabling interrupts until all
coupled CPUs leave idle) rightfully fixed a regression by letting
the coupled idle state framework to handle local interrupt enabling
when the CPU is exiting an idle state.
The current code checks if the idle state is coupled and, if so, it
will let the coupled code to enable interrupts. This way, it can
decrement the ready-count before handling the interrupt. This
mechanism prevents the other CPUs from waiting for a CPU which is
handling interrupts.
But the check is done against the state index returned by the back
end driver's ->enter functions which could be different from the
initial index passed as parameter to the cpuidle_enter_state()
function.
entered_state = target_state->enter(dev, drv, index);
[ ... ]
if (!cpuidle_state_is_coupled(drv, entered_state))
local_irq_enable();
[ ... ]
If the 'index' is referring to a coupled idle state but the
'entered_state' is *not* coupled, then the interrupts are enabled
again. All CPUs blocked on the sync barrier may busy loop longer
if the CPU has interrupts to handle before decrementing the
ready-count. That's consuming more energy than saving.
Fixes: 0b89e9aa28 (cpuidle: delay enabling interrupts until all coupled CPUs leave idle)
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c998c07836 upstream.
Currently the 'registered' member of the cpuidle_device struct is set
to 1 during cpuidle_register_device. In this same function there are
checks to see if the device is already registered to prevent duplicate
calls to register the device, but this value is never set to 0 even on
unregister of the device. Because of this, any attempt to call
cpuidle_register_device after a call to cpuidle_unregister_device will
fail which shouldn't be the case.
To prevent this, set registered to 0 when the device is unregistered.
Fixes: c878a52d3c (cpuidle: Check if device is already registered)
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ae3aeefab upstream.
As pm_runtime_set_active() may fail because the device's parent isn't
active, we can end up executing the ->runtime_resume() callback for the
device when it isn't allowed.
Fix this by invoking pm_runtime_set_active() before running the callback
and let's also deal with the error code.
Fixes: 37f204164d (PM: Add pm_runtime_suspend|resume_force functions)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36e6d081cf upstream.
GPIO lookup tables are supposed to be zero terminated. Let's do that
and avoid accidentally walking off the end.
Fixes: 61dd2ca2d4 ("mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41a3da2b8e upstream.
All configurations are lost and the registers will have
default values when the hardware is suspended and resumed,
so saving the private register space context on suspend, and
restoring it on resume.
Fixes: 4b45efe852 (mfd: Add support for Intel Sunrisepoint LPSS devices)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a18afe809 upstream.
On ads7828 the internal reference defaults to off upon power up. When
using internal reference, it needs to be turned on and the voltage needs
to settle before normal conversion cycle can be started. Hence perform a
dummy read in the probe to enable the internal reference allowing the
voltage to settle before performing a normal read.
Without this fix, the first read from the ADC when using internal
reference always returns incorrect data.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78cbccd3bd upstream.
When KDUMP is triggered the driver first talks to the firmware in INTX
mode, but the adapter firmware is still in MSIX mode. Therefore the first
driver command hangs since the driver is waiting for an INTX response and
firmware gives a MSIX response. If when the OS is installed on a RAID
drive created by the adapter KDUMP will hang since the driver does not
receive a response in sync mode.
Fixed by: Change the firmware to INTX mode if it is in MSIX mode before
sending the first sync command.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc4bf75ea3 upstream.
Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.
In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.
The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.
Fixed by: Adding another kthread_should_stop() before schedule_timeout()
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07beca2be2 upstream.
aac_fib_send has a special function case for initial commands during
driver initialization using wait < 0(pseudo sync mode). In this case,
the command does not sleep but rather spins checking for timeout.This
loop is calls cpu_relax() in an attempt to allow other processes/threads
to use the CPU, but this function does not relinquish the CPU and so the
command will hog the processor. This was observed in a KDUMP
"crashkernel" and that prevented the "command thread" (which is
responsible for completing the command from being timed out) from
starting because it could not get the CPU.
Fixed by replacing "cpu_relax()" call with "schedule()"
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 873ffe154a upstream.
In commit a269913c52 ("rtlwifi: Rework rtl_lps_leave() and
rtl_lps_enter() to use work queue"), the tests for enter/exit
power-save mode were inverted. With this change applied, the
wifi connection becomes much more stable.
Fixes: a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Signed-off-by: Wang YanQing <udknight@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baa1702290 upstream.
The previous patch added an option to rtl8723be to manually select the
antenna for those cases when only a single antenna is present, and the
on-board EEPROM is incorrectly programmed. This patch implements the
necessary changes in the Bluetooth coexistence driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c18d8f5095 upstream.
A number of new laptops have been delivered with only a single antenna.
In principle, this is OK; however, a problem arises when the on-board
EEPROM is programmed to use the other antenna connection. The option
of opening the computer and moving the connector is not always possible
as it will void the warranty in some cases. In addition, this solution
breaks the Windows driver when the box dual boots Linux and Windows.
A fix involving a new module parameter has been developed. This commit
adds the new parameter and implements the changes needed for the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
