ACPI power resources have an order attribute that should be taken
into account when turning them on and off, but it is not used now.
Modify the power resources management code to preserve the
spec-compliant ordering of power resources that power states of
devices depend on (analogous changes will be done separately for
power resources used for wakeup).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 0090def6 (ACPI: Add interface to register/unregister device
to/from power resources) made it possible to indicate to the ACPI
core that if the given device depends on any power resources, then
it should be resumed as soon as all of the power resources required
by it to transition to the D0 power state have been turned on.
Unfortunately, however, this was a mistake, because all devices
depending on power resources should be treated this way (i.e. they
should be resumed when all power resources required by their D0
state have been turned on) and for the majority of those devices
the ACPI core can figure out by itself which (physical) devices
depend on what power resources.
For this reason, replace the code added by commit 0090def6 with a
new, much more straightforward, mechanism that will be used
internally by the ACPI core and remove all references to that code
from kernel subsystems using ACPI.
For the cases when there are (physical) devices that should be
resumed whenever a not directly related ACPI device node goes into
D0 as a result of power resources configuration changes, like in
the SATA case, add two new routines, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), allowing subsystems to manage
such dependencies. Convert the SATA subsystem to use the new
functions accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Daniel writes:
- seqno wrap fixes and debug infrastructure from Mika Kuoppala and Chris
Wilson
- some leftover kill-agp on gen6+ patches from Ben
- hotplug improvements from Damien
- clear fb when allocated from stolen, avoids dirt on the fbcon (Chris)
- Stolen mem support from Chris Wilson, one of the many steps to get to
real fastboot support.
- Some DDI code cleanups from Paulo.
- Some refactorings around lvds and dp code.
- some random little bits&pieces
* tag 'drm-intel-next-2012-12-21' of git://people.freedesktop.org/~danvet/drm-intel: (93 commits)
drm/i915: Return the real error code from intel_set_mode()
drm/i915: Make GSM void
drm/i915: Move GSM mapping into dev_priv
drm/i915: Move even more gtt code to i915_gem_gtt
drm/i915: Make next_seqno debugs entry to use i915_gem_set_seqno
drm/i915: Introduce i915_gem_set_seqno()
drm/i915: Always clear semaphore mboxes on seqno wrap
drm/i915: Initialize hardware semaphore state on ring init
drm/i915: Introduce ring set_seqno
drm/i915: Missed conversion to gtt_pte_t
drm/i915: Bug on unsupported swizzled platforms
drm/i915: BUG() if fences are used on unsupported platform
drm/i915: fixup overlay stolen memory leak
drm/i915: clean up PIPECONF bpc #defines
drm/i915: add intel_dp_set_signal_levels
drm/i915: remove leftover display.update_wm assignment
drm/i915: check for the PCH when setting pch_transcoder
drm/i915: Clear the stolen fb before enabling
drm/i915: Access to snooped system memory through the GTT is incoherent
drm/i915: Remove stale comment about intel_dp_detect()
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
While a privileged program can open a raw socket, attach some
restrictive filter and drop its privileges (or send the socket to an
unprivileged program through some Unix socket), the filter can still
be removed or modified by the unprivileged program. This commit adds a
socket option to lock the filter (SO_LOCK_FILTER) preventing any
modification of a socket filter program.
This is similar to OpenBSD BIOCLOCK ioctl on bpf sockets, except even
root is not allowed change/drop the filter.
The state of the lock can be read with getsockopt(). No error is
triggered if the state is not changed. -EPERM is returned when a user
tries to remove the lock or to change/remove the filter while the lock
is active. The check is done directly in sk_attach_filter() and
sk_detach_filter() and does not affect only setsockopt() syscall.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3e4e4c1f ("ipv6: Introduce ip6_flow_hdr() to fill version,
tclass and flowlabel.) uses ntohl(), which should be htonl().
Found by Fengguang Wu <fengguang.wu@intel.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a tracepoint in ext4_punch_hole.
CC: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cpuidle initialization regression fix from Krzysztof Mazur.
* cpuidle fix for power usage fields handling from Daniel Lezcano.
* ACPI build fix from Yinghai Lu.
-
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=4ifX
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- cpuidle regression fix related to the initialization of state
kobjects from Krzysztof Mazur.
- cpuidle fix removing some not very useful code and making some
user-visible problems go away at the same time. From Daniel Lezcano.
- ACPI build fix from Yinghai Lu.
* tag 'pm+acpi-for-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: remove the power_specified field in the driver
ACPI / glue: Fix build with ACPI_GLUE_DEBUG set
cpuidle: fix number of initialized/destroyed states
The NL80211_ATTR_USE_MFP attribute was originally added for
NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more
useful) with NL80211_CMD_CONNECT, so process that attribute with the
connect command, too.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per email discussion Jouni Malinen pointed out that:
"P2P message exchanges can be executed on the current operating channel
of any operation (both P2P and non-P2P station). These can be on 5 GHz
and even on 60 GHz (so yes, you _can_ do GO Negotiation on 60 GHz).
As an example, it would be possible to receive a GO Negotiation Request
frame on a 5 GHz only radio and then to complete GO Negotiation on that
band. This can happen both when connected to a P2P group (through client
discoverability mechanism) and when connected to a legacy AP (assuming
the station receive Probe Request frame from full scan in the beginning
of P2P device discovery)."
This means that P2P messages can be sent over different radio devices.
However, these should use the same P2P device address so it should be
able to provision this from user-space. This patch adds a parameter for
this to struct vif_params which should only be used during creation of
the P2P device interface.
Cc: Jouni Malinen <j@w1.fi>
Cc: Greg Goldman <ggoldman@broadcom.com>
Cc: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[add error checking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the nl80211_mesh_power_mode enumeration which holds possible
values for the mesh power mode. These modes are unknown, active,
light sleep and deep sleep.
Add power_mode entry to the mesh config structure to hold the
user-configured default mesh power mode. This value will be used
for new peer links.
Add the dot11MeshAwakeWindowDuration value to the mesh config.
The awake window is a duration in TU describing how long the STA
will stay awake after transmitting its beacon in PS mode.
Add access routines to:
- get/set local link-specific power mode (STA)
- get remote STA's link-specific power mode (STA)
- get remote STA's non-peer power mode (STA)
- get/set default mesh power mode (mesh config)
- get/set mesh awake window duration (mesh config)
All config changes may be done at mesh runtime and take effect
immediately.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
[fix commit message line length, error handling in set station]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 1b963c81b1 ("lockdep, rwsem: provide down_write_nest_lock()")
contains a bug in a codepath when CONFIG_DEBUG_LOCK_ALLOC is disabled,
which causes down_read() to be called instead of down_write() by mistake
on such configurations. Fix that.
Reported-and-tested-by: Andrew Clayton <andrew@digital-domain.net>
Reported-and-tested-by: Zlatko Calusic <zlatko.calusic@iskon.hr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull scsi target fixes from Nicholas Bellinger:
"This includes an important >= v3.6 regression bugfix for active I/O
shutdown (Roland), some TMR related failure / corner cases fixes for
long outstanding I/O (Roland), two FCoE target mode fabric fabric role
fixes (MDR), a fix for an incorrect sense code during LUN
communication failure (Dr. Hannes), plus a handful of other minor
fixes.
There are still some outstanding zero-length control CDB regression
fixes that need to be addressed for v3.8, that will be coming in a
follow-up PULL request."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix CmdSN comparison (use cmd->cmd_sn instead of cmd->stat_sn)
target: Release se_cmd when LUN lookup fails for TMR
target: Fix use-after-free in LUN RESET handling
target: Fix missing CMD_T_ACTIVE bit regression for pending WRITEs
tcm_fc: Do not report target role when target is not defined
tcm_fc: Do not indicate retry capability to initiators
target: Use TCM_NO_SENSE for initialisation
target: Introduce TCM_NO_SENSE
target: use correct sense code for LUN communication failure
If the default iosched is built as module, the kernel may deadlock
while trying to load the iosched module on device probe if the probing
was running off async. This is because async_synchronize_full() at
the end of module init ends up waiting for the async job which
initiated the module loading.
async A modprobe
1. finds a device
2. registers the block device
3. request_module(default iosched)
4. modprobe in userland
5. load and init module
6. async_synchronize_full()
Async A waits for modprobe to finish in request_module() and modprobe
waits for async A to finish in async_synchronize_full().
Because there's no easy to track dependency once control goes out to
userland, implementing properly nested flushing is difficult. For
now, make module init perform async_synchronize_full() iff module init
has queued async jobs as suggested by Linus.
This avoids the described deadlock because iosched module doesn't use
async and thus wouldn't invoke async_synchronize_full(). This is
hacky and incomplete. It will deadlock if async module loading nests;
however, this works around the known problem case and seems to be the
best of bad options.
For more details, please refer to the following thread.
http://thread.gmane.org/gmane.linux.kernel/1420814
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the driver's resume function can't completely
restore the configuration in the device, it returns
1 from the callback which will be treated like a HW
restart request, but done directly.
In this case, also call the driver's restart_complete()
function so it can finish the reconfiguration there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building the 80211 DocBook, scripts/kernel-doc reports
the following type of warnings:
Warning(include/net/cfg80211.h:334): No description found for return value of 'cfg80211_get_chandef_type'
These warnings are only reported when scripts/kernel-doc
runs in verbose mode.
To fix these use "Return:" to describe function return values.
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
[adjust for freq_reg_info() change]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current soc-dai.h defines SND_SOC_DAIFMT_NB_NF as (1 << 8),
but normal bit clock / normal frame should be
default settings (= 0).
This patch fixup SND_SOC_DAIFMT_NB_NF as (0 << 8).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update to max77693/max8997 extcon driver:
- Using MHL_TA cable for charging.
- Support JIG cable.
- Support Dock-Audio device for playing music and button of device.
- Support Dock-Smart device for desktop mode with mouse/keyboard.
- Set default UART/USB path on probe().
- Check the state/type of cable after completing initialization.
- Code clean to remove duplicate code and bug fix related to sequence of interrupt.
- Fix irq_flag of max8997/max77693 driver.
Update to arizona extcon driver:
- Headphone measurements.
- Alternative detection mechanism for non-default system designs.
- Microphone clamp integration.
- Support for additional detection pin.
- MICBIAS rise time configuration.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=YOtQ
-----END PGP SIGNATURE-----
Merge tag 'extcon-for-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
This is patch set of extcon for v3.9.
Update to max77693/max8997 extcon driver:
- Using MHL_TA cable for charging.
- Support JIG cable.
- Support Dock-Audio device for playing music and button of device.
- Support Dock-Smart device for desktop mode with mouse/keyboard.
- Set default UART/USB path on probe().
- Check the state/type of cable after completing initialization.
- Code clean to remove duplicate code and bug fix related to sequence of interrupt.
- Fix irq_flag of max8997/max77693 driver.
Update to arizona extcon driver:
- Headphone measurements.
- Alternative detection mechanism for non-default system designs.
- Microphone clamp integration.
- Support for additional detection pin.
- MICBIAS rise time configuration.
Add support for dmaengine API. The drivers can implement the
struct uart_8250_dma member in struct uart_8250_port and
8250.c can take care of the rest.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for polling work mode, i.e. system is perform
periodical check chip status when IRQ-line is not connected to CPU.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
This is the last one: tty_schedule_flip
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One point is to have less places where we actually need tty pointer.
The other is that low_latency is bound to buffer processing and
buffers are now in tty_port. So it makes sense to move low_latency to
tty_port too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty pointer in
many call sites. Only tty_port will be needed and hence no more
tty_port_tty_get calls in those paths.
Now 4 string flipping ones are on turn:
* tty_insert_flip_string_flags
* tty_insert_flip_string_fixed_flag
* tty_prepare_flip_string
* tty_prepare_flip_string_flags
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty pointer in
many call sites. Only tty_port will be needed and hence no more
tty_port_tty_get calls in those paths.
Here we start with tty_buffer_request_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that support for RM9000 and platforms based on it has been removed,
remove the serial driver for it as well. It's really only been a quirk
for an almost 8250 compatible UART anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/tty/serial/8250/8250.c | 70 +----------------------------------------
drivers/tty/serial/8250/Kconfig | 9 ------
include/linux/serial_core.h | 1 -
3 files changed, 1 insertion(+), 79 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core is using power states lifted from ACPI for no
good reason. Remove this reference from the documentation and
alter all users to use an enum specific to the serial core
instead, and define it in <linux/serial_core.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Woithe posted an out of tree enabler/control module for these
cards. Lift the relevant identifiers and put them in the 8250_pci driver
along with code used to control custom registers on these cards.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the function thermal_generate_netlink_event
to receive a thermal zone device instead of a originator id.
This way, the messages will always be bound to a thermal zone.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Make the persistent clock check a kernel config option, so that some
platform can explicitely select it, also make CONFIG_RTC_HCTOSYS and
RTC_SYSTOHC depend on its non-existence, which could prevent the
persistent clock and RTC code from doing similar thing twice during
system's init/suspend/resume phases.
If the CONFIG_HAS_PERSISTENT_CLOCK=n, then no change happens for kernel
which still does the persistent clock check in timekeeping_init().
Cc: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Feng Tang <feng.tang@intel.com>
[jstultz: Added dependency for RTC_SYSTOHC as well]
Signed-off-by: John Stultz <john.stultz@linaro.org>
In current kernel, there are several places which need to check
whether there is a persistent clock for the platform. Current check
is done by calling the read_persistent_clock() and validating its
return value.
So one optimization is to do the check only once in timekeeping_init(),
and use a flag persistent_clock_exist to record it.
v2: Add a has_persistent_clock() helper function, as suggested by John.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The purpose of this option is to allow ARM/etc systems that rely on the
class RTC subsystem to have the same kind of automatic NTP based
synchronization that we have on PC platforms. Today ARM does not
implement update_persistent_clock and makes extensive use of the class
RTC system.
When enabled CONFIG_RTC_SYSTOHC will provide a generic
rtc_update_persistent_clock that stores the current time in the RTC and
is intended complement the existing CONFIG_RTC_HCTOSYS option that loads
the RTC at boot.
Like with RTC_HCTOSYS the platform's update_persistent_clock is used
first, if it works. Platforms with mixed class RTC and non-RTC drivers
need to return ENODEV when class RTC should be used. Such an update for
PPC is included in this patch.
Long term, implementations of update_persistent_clock should migrate to
proper class RTC drivers and use CONFIG_RTC_SYSTOHC instead.
Tested on ARM kirkwood and PPC405
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The pstore RAM backend can get called during resume, and must be defensive
against a suspended time source. Expose getnstimeofday logic that returns
an error instead of a WARN. This can be detected and the timestamp can
be zeroed out.
Reported-by: Doug Anderson <dianders@chromium.org>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The Travel and Carkit adapter should be handled directly by
the charger driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Ignore the low btemp interrupts for ab8500 3.0 and 3.3
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Today the battery recharge is determined with a voltage threshold. This
voltage threshold is only valid when the battery is relaxed. In charging
algorithm the voltage read is the loaded battery voltage and no
compensation is done to get the relaxed voltage. When maintenance
charging is not selected, this makes the recharging condition to almost
immediately activate when there is a discharge present on the battery.
Depending on which vendor the battery comes from this behavior can wear
out the battery much faster than normal.
The fuelgauge driver is responsible to monitor the actual battery
capacity and is able to estimate the remaining capacity. It is better to
use the remaining capacity as a limit to determine when battery should
be recharged.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
When enabling the CCEOC irq we might get false interrupt
from ab8500-driver due to the latched value will be saved
and interpreted as an IRQ when enabled
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Johan Bjornstedt <johan.bjornstedt@stericsson.com>
Signed-off-by: Henrik Solver <henrik.solver@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts arch-vt8500 to make use of CLKSRC_OF. Doing so
removes the need for include/linux/vt8500_timer.h as vt8500_timer_init
no longer needs to be visible outside vt8500_timer.c
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
All legitimate users of this function outside ttm_bo.c are gone, now
it's only an implementation detail.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Instead of dropping everything, waiting for the bo to be unreserved
and trying over, a better strategy would be to do a blocking wait.
This can be mapped a lot better to a mutex_lock-like call.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
There should no longer be assumptions that reserve will always succeed
with the lru lock held, so we can safely break the whole atomic
reserve/lru thing. As a bonus this fixes most lockdep annotations for
reservations.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
We realized that the power usage field is never filled and when it
is filled for tegra, the power_specified flag is not set causing all
of these values to be reset when the driver is initialized with
set_power_state().
However, the power_specified flag can be simply removed under the
assumption that the states are always backward sorted, which is the
case with the current code.
This change allows the menu governor select function and the
cpuidle_play_dead() to be simplified. Moreover, the
set_power_states() function can removed as it does not make sense
any more.
Drop the power_specified flag from struct cpuidle_driver and make
the related changes as described above.
As a consequence, this also fixes the bug where on the dynamic
C-states system, the power fields are not initialized.
[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=42870
References: https://bugzilla.kernel.org/show_bug.cgi?id=43349
References: https://lkml.org/lkml/2012/10/16/518
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>