Commit graph

79,425 commits

Author SHA1 Message Date
Yinghai Lu
5993c4670e ACPI: update ej_event interface to take acpi_device
Should use acpi_device pointer directly instead of use handle and
get the device pointer again later.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-01-15 13:24:59 +01:00
Rafael J. Wysocki
ae281795ec ACPI / scan: Drop the second argument of acpi_bus_trim()
All callers of acpi_bus_trim() pass 1 (true) as the second argument
of it, so remove that argument entirely and change acpi_bus_trim()
to always behave as though it were 1.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
2013-01-15 13:23:53 +01:00
Rafael J. Wysocki
6af9a803f4 ACPI: Remove the ops field from struct acpi_device
The ops field in struct acpi_device is not used anywhere, so remove
it.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
2013-01-15 13:23:33 +01:00
Mark Brown
689557d3c7 mfd: wm5102: Add microphone clamp control registers
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
2013-01-15 15:42:18 +09:00
Mark Brown
1eda6aa7ce extcon: arizona: Support direct microphone measurement via HPDET
With some GPIO control it is possible to detect microphones in a wider
range of configurations by directly measuring the microphone impedance
when the HPDET method cannot distinguish between the behaviour of the
two grounds. Allow a GPIO to be provided in platform data and use it to
implement this behaviour.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
2013-01-15 15:42:18 +09:00
Mark Brown
dd235eea4e extcon: arizona: Support HPDET based accessory identification
The accessory detection functionality in Arizona devices is flexible and
supports several system designs in addition to the default one implemented
by the existing driver. One such design uses the HPDET feature to determine
what kind of accessory is present by comparing measurements taken with the
two headphone grounds available on the device, implement that if selected
by platform data.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
2013-01-15 15:42:18 +09:00
Mark Brown
4f34033382 extcon: arizona: Enable basic headphone identification
Use the headphone detection to identify if the accessory is a headphone or
line load. There are two different revisions of the IP with different
register layouts, support both.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
2013-01-15 15:42:17 +09:00
Mark Brown
92a49871b3 extcon: arizona: Support use of GPIO5 as an input to jack detection
Some system designs provide an input on GPIO5 which in conjunction with
the jack detection feature indicates the presence of an accessory.
Support such systems, using the microphone clamp feature to minimise
wakeups of the processor.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
2013-01-15 15:42:17 +09:00
Mark Brown
dab63eb25c extcon: arizona: Use microphone clamp function if available
Newer Arizona devices include a microphone clamp function which is tied to
jack detect. Activate this feature when present in order to ensure best
performance of the subsystem.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
2013-01-15 15:42:17 +09:00
Mark Brown
b17e54625c extcon: arizona: Allow configuration of MICBIAS rise time
Allow configuration of the rise time for MICBIAS via platform data, the
delay required depends on things like the external component selection.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
2013-01-15 15:42:17 +09:00
Chanwoo Choi
2b75799f5a extcon: max77693: Set default uart/usb path by using platform data
This patch determine default uart/usb path by using platform data.
The MAX77693 MUIC device can possibliy set USB/UART/AUDIO/USB_AUX
/UART_AUX to internal h/w path of MUIC device. So, drvier should
determine default uart/usb path.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
2013-01-15 15:42:16 +09:00
Chanwoo Choi
297620fd1e extcon: max77693: Check the state/type of cable after boot completed
This patch check the state/type of cable after completing the initialization
of platform and notify platform of cable state/type through extcon. If extcon
provider driver notify the state/type of cable before completing platform boot,
this uevent is unused and ignored.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
2013-01-15 15:42:15 +09:00
Chanwoo Choi
154f757fd3 extcon: max77693: Remove duplicate code by making function
This patch make max77693-muic_get_cable_type() function to remove
duplicate code because almost internal function need to read
adc/adc1k/adclow/chg_type value of MUIC register. Also, this patch
add description of internal function move field constant of muic device
from extcon-max77693 driver to max77693 header file because of it
is needed for masking some interrupt through platform data.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
2013-01-15 15:42:14 +09:00
Stephen Warren
c1b724f665 ARM: bcm2835: make use of CLKSRC_OF
Using CLKSRC_OF enables deletion of the SoC-specific header
bcm2835_timer.h, replacing the custom function bcm2835_timer_init() with
the standardized automatic clocksource_of_init().

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2013-01-14 21:45:58 -07:00
Stephen Warren
b2fc382aad Merge remote-tracking branch 'korg_arm-soc/timer/cleanup' into cleanup 2013-01-14 21:44:27 -07:00
Olof Johansson
f8060f5446 Initial irqchip init infrastructure and GIC and VIC clean-ups
This creates irqchip initialization infrastructure from Thomas
 Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
 and adapted to use the new infrastructure. All DT enabled platforms
 using GIC and VIC are converted over to use the new irqchip_init.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQEcBAABAgAGBQJQ8ZobAAoJEMhvYp4jgsXiihIH/2VvxmSHZb0e3jN6AR0B42b7
 9EwX0IE0B23t91hNTwdzzmTJQYA7pMmWkgHNfd3vIeqSepJAmrVv/gp4iM9CtPwE
 KNh+kDWOK2ZsOH4Vb0lYRJHN8WQOIQHuCUr9+MdYLNOgf/pPL6G/Y9kv9A1e7fTC
 W+tFRjC5N1ilZMGyowX12L1wnwDk6kHzed6YV6bskC17cZ9/pg8PhSVbM4A/3kAv
 NXYKqbXJb+eCsWGXg/knZXOL6V9gBwvVYoe4O9X3nQ0226AWB9caad8l8tchAjRB
 fmrYF1tbkpOWPnLxhvQy5b5MJichJgTMJHh7RgiEcc/3f63kOljjlx4QKiqHvT0=
 =q7gm
 -----END PGP SIGNATURE-----

Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux into next/cleanup

From Rob Herring:

Initial irqchip init infrastructure and GIC and VIC clean-ups

This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.

* tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux:
  irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
  ARM: picoxcell: use common irqchip_init function
  ARM: spear: use common irqchip_init function
  irqchip: Move ARM VIC to drivers/irqchip
  ARM: samsung: remove unused tick.h
  ARM: remove unneeded vic.h includes
  ARM: remove mach .handle_irq for VIC users
  ARM: VIC: set handle_arch_irq in VIC initialization
  ARM: VIC: shrink down vic.h
  irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
  ARM: use common irqchip_init for GIC init
  irqchip: Move ARM GIC to drivers/irqchip
  ARM: remove mach .handle_irq for GIC users
  ARM: GIC: set handle_arch_irq in GIC initialization
  ARM: GIC: remove direct use of gic_raise_softirq
  ARM: GIC: remove assembly ifdefs from gic.h
  ARM: mach-ux500: use SGI0 to wake up the other core
  arm: add set_handle_irq() to register the parent IRQ controller handler function
  irqchip: add basic infrastructure
  irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS

Fixed up massive merge conflicts with the timer cleanup due to adjacent changes:

Signed-off-by: Olof Johansson <olof@lixom.net>

Conflicts:
	arch/arm/mach-bcm/board_bcm.c
	arch/arm/mach-cns3xxx/cns3420vb.c
	arch/arm/mach-ep93xx/adssphere.c
	arch/arm/mach-ep93xx/edb93xx.c
	arch/arm/mach-ep93xx/gesbc9312.c
	arch/arm/mach-ep93xx/micro9.c
	arch/arm/mach-ep93xx/simone.c
	arch/arm/mach-ep93xx/snappercl15.c
	arch/arm/mach-ep93xx/ts72xx.c
	arch/arm/mach-ep93xx/vision_ep9307.c
	arch/arm/mach-highbank/highbank.c
	arch/arm/mach-imx/mach-imx6q.c
	arch/arm/mach-msm/board-dt-8960.c
	arch/arm/mach-netx/nxdb500.c
	arch/arm/mach-netx/nxdkn.c
	arch/arm/mach-netx/nxeb500hmi.c
	arch/arm/mach-nomadik/board-nhk8815.c
	arch/arm/mach-picoxcell/common.c
	arch/arm/mach-realview/realview_eb.c
	arch/arm/mach-realview/realview_pb1176.c
	arch/arm/mach-realview/realview_pb11mp.c
	arch/arm/mach-realview/realview_pba8.c
	arch/arm/mach-realview/realview_pbx.c
	arch/arm/mach-socfpga/socfpga.c
	arch/arm/mach-spear13xx/spear1310.c
	arch/arm/mach-spear13xx/spear1340.c
	arch/arm/mach-spear13xx/spear13xx.c
	arch/arm/mach-spear3xx/spear300.c
	arch/arm/mach-spear3xx/spear310.c
	arch/arm/mach-spear3xx/spear320.c
	arch/arm/mach-spear3xx/spear3xx.c
	arch/arm/mach-spear6xx/spear6xx.c
	arch/arm/mach-tegra/board-dt-tegra20.c
	arch/arm/mach-tegra/board-dt-tegra30.c
	arch/arm/mach-u300/core.c
	arch/arm/mach-ux500/board-mop500.c
	arch/arm/mach-ux500/cpu-db8500.c
	arch/arm/mach-versatile/versatile_ab.c
	arch/arm/mach-versatile/versatile_dt.c
	arch/arm/mach-versatile/versatile_pb.c
	arch/arm/mach-vexpress/v2m.c
	include/asm-generic/vmlinux.lds.h
2013-01-14 19:55:03 -08:00
David S. Miller
47fb3a26e2 Merge branch 'master' of git://1984.lsi.us.es/nf
Pablo Neira Ayuso says:

====================
The following patchset contains netfilter fixes for 3.8-rc3,
they are:

* fix possible BUG_ON if several netns are in use and the nf_conntrack
  module is removed, initial patch from Gao feng, final patch from myself.

* fix unset return value if conntrack zone are disabled at
  compile-time, reported by Borislav Petkov, fix from myself.

* fix display error message via dmesg for arp_tables, from Jan Engelhardt.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 18:26:41 -05:00
Paul Moore
5dbbaf2de8 tun: fix LSM/SELinux labeling of tun/tap devices
This patch corrects some problems with LSM/SELinux that were introduced
with the multiqueue patchset.  The problem stems from the fact that the
multiqueue work changed the relationship between the tun device and its
associated socket; before the socket persisted for the life of the
device, however after the multiqueue changes the socket only persisted
for the life of the userspace connection (fd open).  For non-persistent
devices this is not an issue, but for persistent devices this can cause
the tun device to lose its SELinux label.

We correct this problem by adding an opaque LSM security blob to the
tun device struct which allows us to have the LSM security state, e.g.
SELinux labeling information, persist for the lifetime of the tun
device.  In the process we tweak the LSM hooks to work with this new
approach to TUN device/socket labeling and introduce a new LSM hook,
security_tun_dev_attach_queue(), to approve requests to attach to a
TUN queue via TUNSETQUEUE.

The SELinux code has been adjusted to match the new LSM hooks, the
other LSMs do not make use of the LSM TUN controls.  This patch makes
use of the recently added "tun_socket:attach_queue" permission to
restrict access to the TUNSETQUEUE operation.  On older SELinux
policies which do not define the "tun_socket:attach_queue" permission
the access control decision for TUNSETQUEUE will be handled according
to the SELinux policy's unknown permission setting.

Signed-off-by: Paul Moore <pmoore@redhat.com>
Acked-by: Eric Paris <eparis@parisplace.org>
Tested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 18:16:59 -05:00
Olof Johansson
175dbc1eea Move arch-vt8500/timer.c to drivers/clocksource/vt8500-timer.c
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQEcBAABAgAGBQJQ85D4AAoJEAKiPfwuf9N/H54IAKG3Z1cimwst/lS04C0IHvDt
 v//BqaXjTDkYe1bfTp4ButILVW024hQru0MVNNpQanE5H9EUGuGQ98NxkRGuj0na
 7mmWNJypL6+8ajA1256hQD40dYDnn7rx6tXjFPZ2DICJ9gnpGJTkjbnP/Qxeljgl
 s8dYigEN51sUvAdTx07IQ8fOb+W3KQCs5kHAork8NqtHHzYyOPhs5IvV/a+Ti9Ms
 v1KLOhX9F9iV5LURycnM900/bpz7/gHKWXw+shFnt3GwPzyB2beS+Mi2rxrrUOhq
 Q8zHcn52tD9tljiOSVtJDCsUBo1xOJ0HFuhal6rAvX1L5HnFEU8bHcRA8jNLFyE=
 =/DHH
 -----END PGP SIGNATURE-----

Merge tag 'vt8500/timer' of git://server.prisktech.co.nz/git/linuxwmt into next/cleanup

From Tony Prisk:
Move arch-vt8500/timer.c to drivers/clocksource/vt8500-timer.c

* tag 'vt8500/timer' of git://server.prisktech.co.nz/git/linuxwmt:
  timer: vt8500: Move timer code to drivers/clocksource

Signed-off-by: Olof Johansson <olof@lixom.net>
2013-01-14 14:13:48 -08:00
Florian Fainelli
f9a8f83b04 net: phy: remove flags argument from phy_{attach, connect, connect_direct}
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.

Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 15:11:50 -05:00
Nathan Hintz
6bf2e54614 bcma: fix bcm4716/bcm4748 i2s irqflag
The default irqflag assignment for the I2S core on some Broadcom
4716/4748 devices is invalid and needs to be corrected (from the
Broadcom SDK).

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-14 15:10:40 -05:00
Benjamin LaHaise
c1b52739e4 pkt_sched: namespace aware act_mirred
Eric Dumazet pointed out that act_mirred needs to find the current net_ns,
and struct net pointer is not provided in the call chain.  His original
patch made use of current->nsproxy->net_ns to find the network namespace,
but this fails to work correctly for userspace code that makes use of
netlink sockets in different network namespaces.  Instead, pass the
"struct net *" down along the call chain to where it is needed.

This version removes the ifb changes as Eric has submitted that patch
separately, but is otherwise identical to the previous version.

Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 15:09:36 -05:00
John W. Linville
50c2f5e8f9 This is the first NFC patchset targeted at the 3.9 merge window.
It brings the following goodies:
 
 - LLCP socket timestamping (To be used e.g with the recently released nfctool
   application for a more efficient skb timestamping when sniffing).
 - A pretty big pn533 rework from Waldemar, preparing the driver to support
   more flavours of pn533 based devices.
 - HCI changes from Eric in preparation for the microread driver support.
 - Some LLCP memory leak fixes, cleanups and slight improvements.
 - pn544 and nfcwilink move to the devm_kzalloc API.
 - An initial Secure Element (SE) API.
 - An nfc.h license change from the original author, allowing non GPL
   application code to safely include it.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJQ8+7TAAoJEIqAPN1PVmxKHQIP/3dfFPQsOxQRj6sIkFVE/Yzh
 AomeiBh5oGsZkxWzGEolWvHU+DEYTZFz/TKyhneHtWIENTj8+ueo1dh5i35DcKvL
 NiZJT3ASqyJV1ipwQG102y6J511pJsVoQkFSh0Xb/yTDNjwZnL9Jp2N3vsb3rJyN
 DzqNHOx+oCZvjeoGaUzRyjgndcWzeVw0f5IuyRJlCUdh9bj3Er1uP6ugCMiUkMBH
 FcY3Qwdc4WbgtpyYv+Y79/vny1kQ+JPf0Rk9VlylcFZ5RsLEc7K3G3rrTQZktlAT
 /fCVxURotu8XdFf6lj0qRHLnrnTICj1sDcApVOm2XtoXicOtw0q9GaUJVvgPChkc
 vJ2bAYrWMeQ1FZJQt5DaQdsfsglq64ROiAlI8/s9upKP3+Pt0HNnKqUXEZVYTnxZ
 wgFVj20nO2vl5tmI3Z65ZyA1cJ1uSsOcCH8sB7V+OJYQoSKWVyxJw5AOHHh3tHz7
 +JfNrfTvIYG5woUivFmpdVslOHXMCe+lUfrXbvNCfF1PFsTUaQWa/dpxq6/pD991
 eTn5uP+UoJqL5oiYQJzwbKMvQ+3qGPxQuaVhbicRQRiCYA3yflg43iN8aSe4ARzs
 5dxY66WZgmAG1gamKxx7tJiPmkmgrrd/jAztLHdEZLmYnDUr+yQoazkaTOcWUCBt
 J7RoY3HcZsiDYwuB/D14
 =YeWq
 -----END PGP SIGNATURE-----

Merge tag 'nfc-next-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next

Samuel Ortiz <sameo@linux.intel.com> says:

"This is the first NFC patchset targeted at the 3.9 merge window.

It brings the following goodies:

- LLCP socket timestamping (To be used e.g with the recently released nfctool
  application for a more efficient skb timestamping when sniffing).
- A pretty big pn533 rework from Waldemar, preparing the driver to support
  more flavours of pn533 based devices.
- HCI changes from Eric in preparation for the microread driver support.
- Some LLCP memory leak fixes, cleanups and slight improvements.
- pn544 and nfcwilink move to the devm_kzalloc API.
- An initial Secure Element (SE) API.
- An nfc.h license change from the original author, allowing non GPL
  application code to safely include it."

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-14 15:08:52 -05:00
YOSHIFUJI Hideaki / 吉藤英明
6059283378 ipv6 netevent: Remove old_neigh from netevent_redirect.
The only user is cxgb3 driver.

old_neigh is used to check device change, but it must not happen
on redirect.  In this sense, we can remove old_neigh argument.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 15:04:59 -05:00
Linus Torvalds
9bbcbad438 Sound fixes for 3.8-rc4
Most of commits found here are for ASoC device specific fixes,
 arizona, cs4271, wm5102, wm2200, etc, in addition to a couple of
 memory leak fixes in ASoC core.
 
 Other than that, regression fixes in HD-audio and USB-audio, and
 a fix for new Realtek codecs.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIcBAABAgAGBQJQ88mfAAoJEGwxgFQ9KSmkbXkP/3NGkP2N7DX6qK9pJ00sR9dY
 gMmu0yM+W/jJZ0Xf2yU7x/sZdWrUbtICOZ67cOrG7M9W3DIOzMtvaiMCIh12+LUH
 xU1KRPfVe+oLGy6eQBR5o45z4DNNwgNZ9LpKv8/DySrRMJ60hJ4jxJKSnMmTyCe7
 vMlp9k1nJP41jkZX1rRW3JrBBSMB9NHWiltm+GIZJ3VKqM3+uiJJZaMAWcjnMiYy
 tnVOxomJzNPCxv9Bv2GzgD0MII0G8olYhXeVJP3B76EnNbK6G5PbxmkTp+/oKVQf
 fU2Z5FheqqT3mjYeYo++vj0E5Dau+iYU02z0uHMMErUCpKTvwGa2szBH1PPOqcHU
 H85EBJ12OQt8vNNpGSKdPBtAqqOJm9C1jcT1387Dubq9Oz2X113Zl7QI3xH5u91s
 8lDhJI4XhlDwjSe5SUCHsdIwG4uQM9UOdc8hEJkCMemu2cFQTJUN5mwRJsd9B6Po
 ACB231GwNsRRq28nh1AxtroWUlO7exWOpsbqwoF6zuhwtUzR1Vm87Vd4go/T2wTD
 Lvyt5rDSnhFHWELkVBTk3/U/6fn0aQ8pR0wuScF1VoQCF1vphlEBWuHUOnorFmd+
 gt1T4pp4jc/xmCZLdMXlCcsctPb+5HRVO+DkfCh9RYDvanh8HfgUF/WlhF361qXr
 Vu4uLsazWMJSFX/gXTzn
 =iVG2
 -----END PGP SIGNATURE-----

Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
 "Most of commits found here are for ASoC device specific fixes,
  arizona, cs4271, wm5102, wm2200, etc, in addition to a couple of
  memory leak fixes in ASoC core.

  Other than that, regression fixes in HD-audio and USB-audio, and a fix
  for new Realtek codecs."

* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
  ALSA: usb-audio: Fix NULL dereference by access to non-existing substream
  ALSA: hda - Add support of new codec ALC284
  ALSA: usb-audio: Make ebox44_table static
  ALSA: hdspm - Fix wordclock status on AES32
  Revert "ALSA: hda - Shut up pins at power-saving mode with Conexnat codecs"
  ALSA: hda - Disable runtime D3 for Intel CPT & co
  ALSA: pxa27x: fix ac97 warm reset
  ALSA: pxa27x: fix ac97 cold reset
  ASoC: wm_adsp: Ensure that block writes are from DMA aligned addresses
  ASoC: wm2000: Fix sense of speech clarity enable
  ASoC: wm5100: Remove DSP B and left justified formats
  ASoC: arizona: Remove DSP B and left justified AIF modes
  ASoC: wm2200: Remove DSP B and left justified AIF modes
  ASoC: wm5102: Improve speaker enable performance
  ASoC: core: fix the memory leak in case of remove_aux_dev()
  ASoC: core: fix the memory leak in case of device_add() failure
  ASoC: cs42l52: Catch no-match case in cs42l52_get_clk
  ASoC: lm49453: Update lm49453_reg_defs values as per LM49453 HW revision-B
  ASoC: lm49453: Fix adc, mic and sidetone volume ranges
  ASoC: arizona: Correct FLL source definitions
  ...
2013-01-14 10:56:05 -08:00
David Milburn
1757d902b0 libata: export host controller number thru /sys
As low-level drivers register their host controller(s), keep track
of the number of controllers and export thru /sys in a <host.port>
format so that udev can better match up port numbers with a
specific controller.

# pwd
/sys/devices/pci0000:00
# find . -name 'ata*' -print

(2nd controller with port multiplier attached)

./0000:00:1e.0/0000:05:01.0/ata2.7
./0000:00:1e.0/0000:05:01.0/ata2.7/link7/dev7.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.0/dev7.0.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.0/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.1/dev7.1.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.1/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.2/dev7.2.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.2/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.3/dev7.3.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.3/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.4/dev7.4.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.4/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.5/dev7.5.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.5/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.6/dev7.6.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.6/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.7/dev7.7.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.7/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.8/dev7.8.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.8/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.9/dev7.9.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.9/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/ata_port
./0000:00:1e.0/0000:05:01.0/ata2.7/ata_port/ata2.7
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.10/dev7.10.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.10/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.11/dev7.11.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.11/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.12/dev7.12.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.12/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.13/dev7.13.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.13/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.14/dev7.14.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.7/link7.14/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.8
./0000:00:1e.0/0000:05:01.0/ata2.8/link8/dev8.0/ata_device
./0000:00:1e.0/0000:05:01.0/ata2.8/link8/ata_link
./0000:00:1e.0/0000:05:01.0/ata2.8/ata_port
./0000:00:1e.0/0000:05:01.0/ata2.8/ata_port/ata2.8

(1st controller)

./0000:00:1f.2/ata1.1
./0000:00:1f.2/ata1.1/link1/dev1.0/ata_device
./0000:00:1f.2/ata1.1/link1/ata_link
./0000:00:1f.2/ata1.1/ata_port
./0000:00:1f.2/ata1.1/ata_port/ata1.1
./0000:00:1f.2/ata1.2
./0000:00:1f.2/ata1.2/link2/dev2.0/ata_device
./0000:00:1f.2/ata1.2/link2/ata_link
./0000:00:1f.2/ata1.2/ata_port
./0000:00:1f.2/ata1.2/ata_port/ata1.2
./0000:00:1f.2/ata1.3
./0000:00:1f.2/ata1.3/link3/dev3.0/ata_device
./0000:00:1f.2/ata1.3/link3/ata_link
./0000:00:1f.2/ata1.3/ata_port
./0000:00:1f.2/ata1.3/ata_port/ata1.3
./0000:00:1f.2/ata1.4
./0000:00:1f.2/ata1.4/link4/dev4.0/ata_device
./0000:00:1f.2/ata1.4/link4/ata_link
./0000:00:1f.2/ata1.4/ata_port
./0000:00:1f.2/ata1.4/ata_port/ata1.4
./0000:00:1f.2/ata1.5
./0000:00:1f.2/ata1.5/link5/dev5.0/ata_device
./0000:00:1f.2/ata1.5/link5/ata_link
./0000:00:1f.2/ata1.5/ata_port
./0000:00:1f.2/ata1.5/ata_port/ata1.5
./0000:00:1f.2/ata1.6
./0000:00:1f.2/ata1.6/link6/dev6.0/ata_device
./0000:00:1f.2/ata1.6/link6/ata_link
./0000:00:1f.2/ata1.6/ata_port
./0000:00:1f.2/ata1.6/ata_port/ata1.6

Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-01-14 13:31:21 -05:00
Shane Huang
803739d25c [libata] replace sata_settings with devslp_timing
NCQ capability was used to check availability of SATA Settings page
from Identify Device Data Log, which contains DevSlp timing variables.
It does not work on some HDDs and leads to error messages.

IDENTIFY word 78 bit 5(Hardware Feature Control) can't work either
because it is only the sufficient condition of Identify Device data
log, not the necessary condition.

This patch replaced ata_device->sata_settings with ->devslp_timing
to only save DevSlp timing variables(8 bytes), instead of the whole
SATA Settings page(512 bytes).

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=51881

Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-01-14 13:29:15 -05:00
Olof Johansson
8d84981e39 Merge branch 'clocksource/cleanup' into next/cleanup
Clockevent cleanup series from Shawn Guo.

Resolved move/change conflict in mach-pxa/time.c due to the sys_timer
cleanup.

* clocksource/cleanup:
  clocksource: use clockevents_config_and_register() where possible
  ARM: use clockevents_config_and_register() where possible
  clockevents: export clockevents_config_and_register for module use
  + sync to Linux 3.8-rc3

Signed-off-by: Olof Johansson <olof@lixom.net>

Conflicts:
	arch/arm/mach-pxa/time.c
2013-01-14 10:20:02 -08:00
YOSHIFUJI Hideaki / 吉藤英明
38675170e4 ipv6: 64bit version of ipv6_prefix_equal().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 13:17:01 -05:00
YOSHIFUJI Hideaki / 吉藤英明
2ef9733203 ipv6: Remove __ipv6_prefix_equal().
ipv6_prefix_equal() just casts its arguments and it is the only
user of __ipv6_prefix_equal().

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 13:17:01 -05:00
YOSHIFUJI Hideaki / 吉藤英明
5206c579da ipv6: 64bit version of ipv6_addr_set().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 13:17:01 -05:00
YOSHIFUJI Hideaki / 吉藤英明
a04d40b895 ipv6: 64bit version of ipv6_addr_v4mapped().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 13:17:00 -05:00
YOSHIFUJI Hideaki / 吉藤英明
e287656b36 ipv6: 64bit version of ipv6_addr_loopback().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 13:17:00 -05:00
YOSHIFUJI Hideaki / 吉藤英明
9f2e73345a ipv6: 64bit version of ipv6_addr_diff().
Introduce __ipv6_addr_diff64() to to find the first different
bit between two addresses on 64bit architectures.

32bit version is still available as __ipv6_addr_diff32(),
and __ipv6_addr_diff() automatically selects appropriate
version.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-14 13:17:00 -05:00
Daniel Mack
ccf04c5100 mtd: omap-nand: pass device_node in platform data
Pass an optional device_node pointer in the platform data, which in turn
will be put into a mtd_part_parser_data. This way, code that sets up the
platform devices can pass along the node from DT so that the partitions
can be parsed.

For non-DT boards, this change has no effect.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-01-14 09:55:19 -08:00
Linus Torvalds
3441f0d26d Driver core fixes for 3.8-rc3
Here are two patches for 3.8-rc3.
 
 One removes the __dev* defines from init.h now that all usages of it are gone
 from your tree.  The other fix is for debugfs's paramater that was using the
 wrong base for the option.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iEYEABECAAYFAlDzjcAACgkQMUfUDdst+ykJVwCcDqiKrO9p0dcH9WXN5aukBWX/
 N8EAoK786v7PjtiVyNOJ/cPUDU8OHUpg
 =U4nL
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg Kroah-Hartman:
 "Here are two patches for 3.8-rc3.

  One removes the __dev* defines from init.h now that all usages of it
  are gone from your tree.  The other fix is for debugfs's paramater
  that was using the wrong base for the option.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'driver-core-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  debugfs: convert gid= argument from decimal, not octal
  Remove __dev* markings from init.h
2013-01-14 09:07:11 -08:00
Linus Torvalds
6843cc0e0f Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) Fix regression allowing IP_TTL setting of zero, fix from Cong Wang.

 2) Fix leak regressions in tunap, from Jason Wang.

 3) be2net driver always returns IRQ_HANDLED in INTx handler, fix from
    Sathya Perla.

 4) qlge doesn't really support NETIF_F_TSO6, don't set that flag.  Fix
    from Amerigo Wang.

 5) Add 802.11ad Atheros wil6210 driver, from Vladimir Kondratiev.

 6) Fix MTU calculations in mac80211 layer, from T Krishna Chaitanya.

 7) Station info layer of mac80211 needs to use del_timer_sync(), from
    Johannes Berg.

 8) tcp_read_sock() can loop forever, because we don't immediately stop
    when recv_actor() returns zero.  Fix from Eric Dumazet.

 9) Fix WARN_ON() in tcp_cleanup_rbuf().  We have to use sk_eat_skb() in
    tcp_recv_skb() to handle the case where a large GRO packet is split
    up while it is use by a splice() operation.  Fix also from Eric
    Dumazet.

10) addrconf_get_prefix_route() in ipv6 tests flags incorrectly, it
    does:

        if (X && (p->flags & Y) != 0)

    when it really meant to go:

        if (X && (p->flags & X) != 0)

    fix from Romain Kuntz.

11) Fix lost Kconfig dependency for bfin_mac driver hardware
    timestamping.  From Lars-Peter Clausen.

12) Fix regression in handling of RST without ACK in TCP, from Eric
    Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
  be2net: fix unconditionally returning IRQ_HANDLED in INTx
  tuntap: fix leaking reference count
  tuntap: forbid calling TUNSETIFF when detached
  tuntap: switch to use rtnl_dereference()
  net, wireless: overwrite default_ethtool_ops
  qlge: remove NETIF_F_TSO6 flag
  tcp: accept RST without ACK flag
  net: ethernet: xilinx: Do not use NO_IRQ in axienet
  net: ethernet: xilinx: Do not use axienet on PPC
  bnx2x: Allow management traffic after boot from SAN
  bnx2x: Fix fastpath structures when memory allocation fails
  bfin_mac: Restore hardware time-stamping dependency on BF518
  tun: avoid owner checks on IFF_ATTACH_QUEUE
  bnx2x: move debugging code before the return
  tuntap: refuse to re-attach to different tun_struct
  ipv6: use addrconf_get_prefix_route for prefix route lookup [v2]
  ipv6: fix the noflags test in addrconf_get_prefix_route
  tcp: fix splice() and tcp collapsing interaction
  tcp: splice: fix an infinite loop in tcp_read_sock()
  net: prevent setting ttl=0 via IP_TTL
  ...
2013-01-14 08:27:10 -08:00
Tejun Heo
9fb0a7da0c writeback: add more tracepoints
Add tracepoints for page dirtying, writeback_single_inode start, inode
dirtying and writeback.  For the latter two inode events, a pair of
events are defined to denote start and end of the operations (the
starting one has _start suffix and the one w/o suffix happens after
the operation is complete).  These inode ops are FS specific and can
be non-trivial and having enclosing tracepoints is useful for external
tracers.

This is part of tracepoint additions to improve visiblity into
dirtying / writeback operations for io tracer and userland.

v2: writeback_dirty_inode[_start] TPs may be called for files on
    pseudo FSes w/ unregistered bdi.  Check whether bdi->dev is %NULL
    before dereferencing.

v3: buffer dirtying moved to a block TP.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2013-01-14 15:00:36 +01:00
Tejun Heo
5305cb8308 block: add block_{touch|dirty}_buffer tracepoint
The former is triggered from touch_buffer() and the latter
mark_buffer_dirty().

This is part of tracepoint additions to improve visiblity into
dirtying / writeback operations for io tracer and userland.

v2: Transformed writeback_dirty_buffer to block_dirty_buffer and made
    it share TP definition with block_touch_buffer.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2013-01-14 15:00:36 +01:00
Tejun Heo
f0059afd3e buffer: make touch_buffer() an exported function
We want to add a trace point to touch_buffer() but macros and inline
functions defined in header files can't have tracing points.  Move
touch_buffer() to fs/buffer.c and make it a proper function.

The new exported function is also declared inline.  As most uses of
touch_buffer() are inside buffer.c with nilfs2 as the only other user,
the effect of this change should be negligible.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2013-01-14 15:00:36 +01:00
Tejun Heo
8c1cf6bb02 block: add @req to bio_{front|back}_merge tracepoints
bio_{front|back}_merge tracepoints report a bio merging into an
existing request but didn't specify which request the bio is being
merged into.  Add @req to it.  This makes it impossible to share the
event template with block_bio_queue - split it out.

@req isn't used or exported to userland at this point and there is no
userland visible behavior change.  Later changes will make use of the
extra parameter.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2013-01-14 15:00:36 +01:00
Tejun Heo
3a366e614d block: add missing block_bio_complete() tracepoint
bio completion didn't kick block_bio_complete TP.  Only dm was
explicitly triggering the TP on IO completion.  This makes
block_bio_complete TP useless for tracers which want to know about
bios, and all other bio based drivers skip generating blktrace
completion events.

This patch makes all bio completions via bio_endio() generate
block_bio_complete TP.

* Explicit trace_block_bio_complete() invocation removed from dm and
  the trace point is unexported.

* @rq dropped from trace_block_bio_complete().  bios may fly around
  w/o queue associated.  Verifying and accessing the assocaited queue
  belongs to TP probes.

* blktrace now gets both request and bio completions.  Make it ignore
  bio completions if request completion path is happening.

This makes all bio based drivers generate blktrace completion events
properly and makes the block_bio_complete TP actually useful.

v2: With this change, block_bio_complete TP could be invoked on sg
    commands which have bio's with %NULL bi_bdev.  Update TP
    assignment code to check whether bio->bi_bdev is %NULL before
    dereferencing.

Signed-off-by: Tejun Heo <tj@kernel.org>
Original-patch-by: Namhyung Kim <namhyung@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2013-01-14 15:00:36 +01:00
Jiang Liu
115c9ad854 ACPI: remove unused acpi_op_bind and acpi_op_unbind
With commit f2a33cde55a03 "ACPI: Drop ACPI device .bind() and .unbind()
callbacks", acpi_op_bind and acpi_op_unbind are not used any more. So
remove them.

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-01-14 13:55:41 +01:00
Lauro Ramos Venancio
d3710e74cf NFC: Change nfc.h license
nfc.h being GPL makes it quite controversial for non GPL applications to
include it.
Moreover, nfc.h only includes structures and API definitions that are hardly
copyrightable.

Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-14 12:28:54 +01:00
Luis R. Rodriguez
0c0280bd0b wireless: make the reg_notifier() void
The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.

Also make lbs_reg_notifier static.

Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-14 11:32:44 +01:00
Fabio Baltieri
7407048bec dmaengine: ste_dma40: add software lli support
This patch add support to manage LLI by SW for select phy channels.

There is a HW issue in certain controllers due to which on certain
occassions HW LLI cannot be used on some physical channels.  To avoid
the HW issue on a specific phy channel, the phy channel number can be
added to the list of soft_lli_channels and there after all the transfers
on that channel will use software LLI, for peripheral to memory
transfers.

SoftLLI introduces relink overhead, that could impact performace for
certain use cases.

This is based on a previous patch of Narayanan Gopalakrishnan.

Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
2013-01-14 10:51:08 +01:00
Fabio Baltieri
762eb33fde dmaengine: ste_dma40: add missing kernel-doc entry
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
2013-01-14 10:50:56 +01:00
Gerald Baeza
47db92f4a6 dmaengine: ste_dma40: physical channels number correction
DMAC_ICFG[0:2]=SCHNB only allows to count 'multiple of 4' physical
channels so it was ok with platforms having 8 channels but cannot be
used for next versions (with 10 or 14 channels).  This patch allows to
provide the number of physical channels for a DMA device via
platform_data, or still rely on SCHNB if platform_data announces 0
channel.

Signed-off-by: Gerald Baeza <gerald.baeza@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
2013-01-14 10:50:44 +01:00
Gleb Natapov
aa11e3a8a6 Merge branch 'kvm-ppc-next' of https://github.com/agraf/linux-2.6 into queue 2013-01-14 11:01:26 +02:00
Tony Prisk
ff7ec345f0 timer: vt8500: Move timer code to drivers/clocksource
This patch moves arch-vt8500/timer.c into drivers/clocksource and
updates the necessary Kconfig/Makefile options.

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
2013-01-14 17:58:21 +13:00