commit 35abcd4f9f upstream.
This fixes the following warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function
'brcmf_usb_probe_phase2':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:1198:2:
warning: 'devinfo' may be used uninitialized in this function
[-Wmaybe-uninitialized]
mutex_unlock(&devinfo->dev_init_lock);
Fixes: 6d0507a777 ("brcmfmac: add parameter to pass error code in firmware callback")
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 898805e0cd upstream.
The Marvell driver incorrectly provides phydev->lp_advertising as the
logical and of the link partner's advert and our advert. This is
incorrect - this field is supposed to store the link parter's unmodified
advertisment.
This allows ethtool to report the correct link partner auto-negotiation
status.
Fixes: be937f1f89 ("Marvell PHY m88e1111 driver fix")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 833bfade96 upstream.
The generic SPI code calculates how long the issued transfer would take
and adds 100ms in addition to the timeout as tolerance. On my 500 MHz
Lantiq Mips SoC I am getting timeouts from the SPI like this when the
system boots up:
m25p80 spi32766.4: SPI transfer timed out
blk_update_request: I/O error, dev mtdblock3, sector 2
SQUASHFS error: squashfs_read_data failed to read block 0x6e
After increasing the tolerance for the timeout to 200ms I haven't seen
these SPI transfer time outs any more.
The Lantiq SPI driver in use here has an extra work queue in between,
which gets triggered when the controller send the last word and the
hardware FIFOs used for reading and writing are only 8 words long.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2201ac6129 upstream.
The code responsible for splitting periods into chunks that
can be handled by the DMA controller missed to update total_len,
the number of bytes processed in the current period, when there
are more chunks to follow.
Therefore total_len was stuck at 0 and the code didn't work at all.
This resulted in a wrong control block layout and audio issues because
the cyclic DMA callback wasn't executing on period boundaries.
Fix this by adding the missing total_len update.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb1a619735 upstream.
USB PHYs need the MDIO clock divisor enabled earlier to work.
Initialize mdio clock divisor in probe function. The ext bus
bit available in the same register will be used by mdio mux
to enable external mdio.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6232c17438 upstream.
As reported by Felix:
Though protected by an ifdef, introducing an usb symbol dependency in
the rt2x00lib module is a major inconvenience for distributions that
package kernel modules split into individual packages.
Get rid of this unnecessary dependency by calling the usb related
function from a more suitable place.
Cc: Vishal Thanki <vishalthanki@gmail.com>
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7f73850bb upstream.
Companion descriptor is only used for SuperSpeed endpoints,
if the endpoints are HighSpeed or FullSpeed, the Companion
descriptor will not allocated, so we can only access it if
gadget is SuperSpeed.
I can reproduce this issue on Rockchip platform rk3368 SoC
which supports USB 2.0, and use functionfs for ADB. Kernel
build with CONFIG_KASAN=y and CONFIG_SLUB_DEBUG=y report
the following BUG:
==================================================================
BUG: KASAN: slab-out-of-bounds in ffs_func_set_alt+0x224/0x3a0 at addr ffffffc0601f6509
Read of size 1 by task swapper/0/0
============================================================================
BUG kmalloc-256 (Not tainted): kasan: bad access detected
----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in ffs_func_bind+0x52c/0x99c age=1275 cpu=0 pid=1
alloc_debug_processing+0x128/0x17c
___slab_alloc.constprop.58+0x50c/0x610
__slab_alloc.isra.55.constprop.57+0x24/0x34
__kmalloc+0xe0/0x250
ffs_func_bind+0x52c/0x99c
usb_add_function+0xd8/0x1d4
configfs_composite_bind+0x48c/0x570
udc_bind_to_driver+0x6c/0x170
usb_udc_attach_driver+0xa4/0xd0
gadget_dev_desc_UDC_store+0xcc/0x118
configfs_write_file+0x1a0/0x1f8
__vfs_write+0x64/0x174
vfs_write+0xe4/0x200
SyS_write+0x68/0xc8
el0_svc_naked+0x24/0x28
INFO: Freed in inode_doinit_with_dentry+0x3f0/0x7c4 age=1275 cpu=7 pid=247
...
Call trace:
[<ffffff900808aab4>] dump_backtrace+0x0/0x230
[<ffffff900808acf8>] show_stack+0x14/0x1c
[<ffffff90084ad420>] dump_stack+0xa0/0xc8
[<ffffff90082157cc>] print_trailer+0x188/0x198
[<ffffff9008215948>] object_err+0x3c/0x4c
[<ffffff900821b5ac>] kasan_report+0x324/0x4dc
[<ffffff900821aa38>] __asan_load1+0x24/0x50
[<ffffff90089eb750>] ffs_func_set_alt+0x224/0x3a0
[<ffffff90089d3760>] composite_setup+0xdcc/0x1ac8
[<ffffff90089d7394>] android_setup+0x124/0x1a0
[<ffffff90089acd18>] _setup+0x54/0x74
[<ffffff90089b6b98>] handle_ep0+0x3288/0x4390
[<ffffff90089b9b44>] dwc_otg_pcd_handle_out_ep_intr+0x14dc/0x2ae4
[<ffffff90089be85c>] dwc_otg_pcd_handle_intr+0x1ec/0x298
[<ffffff90089ad680>] dwc_otg_pcd_irq+0x10/0x20
[<ffffff9008116328>] handle_irq_event_percpu+0x124/0x3ac
[<ffffff9008116610>] handle_irq_event+0x60/0xa0
[<ffffff900811af30>] handle_fasteoi_irq+0x10c/0x1d4
[<ffffff9008115568>] generic_handle_irq+0x30/0x40
[<ffffff90081159b4>] __handle_domain_irq+0xac/0xdc
[<ffffff9008080e9c>] gic_handle_irq+0x64/0xa4
...
Memory state around the buggy address:
ffffffc0601f6400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0601f6480: 00 00 00 00 00 00 00 00 00 00 06 fc fc fc fc fc
>ffffffc0601f6500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffffffc0601f6580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffffffc0601f6600: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 807c162533 upstream.
With the S25FL127S nor flash part, each writing to the configuration
register takes hundreds of ms. During that time, no more accesses to
the flash should be done (even reads).
This commit adds a wait loop after the register writing until the flash
finishes its work.
This issue could make rootfs mounting fail when the latter was done too
much closely to this quad enable bit setting step. And in this case, a
driver as UBIFS may try to recover the filesystem and may broke it
completely.
Signed-off-by: Joël Esponde <joel.esponde@honeywell.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ec754410c upstream.
An empty __dtb_start to __dtb_end section might result in
initial_boot_params being null for arch/mips/ralink. This showed that the
boot process hangs indefinitely in of_scan_flat_dt().
Signed-off-by: Tobias Wolf <dev-NTEO@vplace.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14605/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52b482b0f4 upstream.
Increase the default display clock on newer asics to
accomodate some high res modes with really high refresh
rates.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=93826
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05b4017b37 upstream.
We were using the wrong structure which lead to an overflow
on some boards.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=101387
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abb85a9b51 upstream.
When iscsi WRITE underflow occurs there are two different scenarios
that can happen.
Normally in practice, when an EDTL vs. SCSI CDB TRANSFER LENGTH
underflow is detected, the iscsi immediate data payload is the
smaller SCSI CDB TRANSFER LENGTH.
That is, when a host fabric LLD is using a fixed size EDTL for
a specific control CDB, the SCSI CDB TRANSFER LENGTH and actual
SCSI payload ends up being smaller than EDTL. In iscsi, this
means the received iscsi immediate data payload matches the
smaller SCSI CDB TRANSFER LENGTH, because there is no more
SCSI payload to accept beyond SCSI CDB TRANSFER LENGTH.
However, it's possible for a malicous host to send a WRITE
underflow where EDTL is larger than SCSI CDB TRANSFER LENGTH,
but incoming iscsi immediate data actually matches EDTL.
In the wild, we've never had a iscsi host environment actually
try to do this.
For this special case, it's wrong to truncate part of the
control CDB payload and continue to process the command during
underflow when immediate data payload received was larger than
SCSI CDB TRANSFER LENGTH, so go ahead and reject and drop the
bogus payload as a defensive action.
Note this potential bug was originally relaxed by the following
for allowing WRITE underflow in MSFT FCP host environments:
commit c72c525022
Author: Roland Dreier <roland@purestorage.com>
Date: Wed Jul 22 15:08:18 2015 -0700
target: allow underflow/overflow for PR OUT etc. commands
Cc: Roland Dreier <roland@purestorage.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 105fa2f44e upstream.
This patch fixes a BUG() in iscsit_close_session() that could be
triggered when iscsit_logout_post_handler() execution from within
tx thread context was not run for more than SECONDS_FOR_LOGOUT_COMP
(15 seconds), and the TCP connection didn't already close before
then forcing tx thread context to automatically exit.
This would manifest itself during explicit logout as:
[33206.974254] 1 connection(s) still exist for iSCSI session to iqn.1993-08.org.debian:01:3f5523242179
[33206.980184] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 2100.772 msecs
[33209.078643] ------------[ cut here ]------------
[33209.078646] kernel BUG at drivers/target/iscsi/iscsi_target.c:4346!
Normally when explicit logout attempt fails, the tx thread context
exits and iscsit_close_connection() from rx thread context does the
extra cleanup once it detects conn->conn_logout_remove has not been
cleared by the logout type specific post handlers.
To address this special case, if the logout post handler in tx thread
context detects conn->tx_thread_active has already been cleared, simply
return and exit in order for existing iscsit_close_connection()
logic from rx thread context do failed logout cleanup.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Tested-by: Gary Guo <ghg@datera.io>
Tested-by: Chu Yuan Lin <cyl@datera.io>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73d4e580cc upstream.
This patch fixes a se_cmd->cmd_kref underflow during CMD_T_ABORTED
when a fabric driver drops it's second reference from below the
target_core_tmr.c based callers of transport_cmd_finish_abort().
Recently with the conversion of kref to refcount_t, this bug was
manifesting itself as:
[705519.601034] refcount_t: underflow; use-after-free.
[705519.604034] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 20116.512 msecs
[705539.719111] ------------[ cut here ]------------
[705539.719117] WARNING: CPU: 3 PID: 26510 at lib/refcount.c:184 refcount_sub_and_test+0x33/0x51
Since the original kref atomic_t based kref_put() didn't check for
underflow and only invoked the final callback when zero was reached,
this bug did not manifest in practice since all se_cmd memory is
using preallocated tags.
To address this, go ahead and propigate the existing return from
transport_put_cmd() up via transport_cmd_finish_abort(), and
change transport_cmd_finish_abort() + core_tmr_handle_tas_abort()
callers to only do their local target_put_sess_cmd() if necessary.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Tested-by: Gary Guo <ghg@datera.io>
Tested-by: Chu Yuan Lin <cyl@datera.io>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a51461fc2 upstream.
When request firmware fails, brcmf_ops_sdio_remove is being called and
brcmf_bus freed. In such circumstancies if you do a suspend/resume cycle
the kernel hangs on resume due a NULL pointer dereference in resume
function. So in brcmf_sdio_firmware_callback() we need to unbind the
driver from both sdio_func devices when firmware load failure is indicated.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03fb0e8393 upstream.
When firmware loading failed the code used to unbind the device provided
by the calling code. However, for the sdio driver two devices are bound
and both need to be released upon failure. The callback has been extended
with parameter to pass error code so add that in this commit upon firmware
loading failure.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d0507a777 upstream.
Extend the parameters in the firmware callback so it can be called
upon success and failure. This allows the caller to properly clear
all resources in the failure path. Right now the error code is
always zero, ie. success.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817ae460c7 upstream.
Without this quirk, the touchpad is not responsive on this product, with
the following message repeated in the logs:
psmouse serio1: bad data from KBC - timeout
Add it to the notimeout list alongside other similar Fujitsu laptops.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3db28271f0 upstream.
This mouse is also known under other IDs. It needs the quirk
ALWAYS_POLL or will disconnect in runlevel 1 or 3.
Signed-off-by: Sebastian Parschauer <sparschauer@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dec6b33163 upstream.
During the module initialisation there is a possible race
(basically race between uld and lld) where neither the uld
nor lld notifies the uP about where to route the ctrl queue
completions. LLD skips notifying uP as the rdma queues were
not created by then (will leave it to ULD to notify the uP).
As the ULD comes up, it also skips notifying the uP as the
flag FULL_INIT_DONE is not set yet (ULD assumes that the
interface is not up yet).
Consequently, this race between uld and lld leaves uP
unnotified about where to send the ctrl queue completions
to, leading to iwarp RI_RES WR failure.
Here is the race:
CPU 0 CPU1
- allocates nic rx queus
- t4_sge_alloc_ctrl_txq()
(if rdma rsp queues exists,
tell uP to route ctrl queue
compl to rdma rspq)
- acquires the mutex_lock
- allocates rdma response queues
- if FULL_INIT_DONE set,
tell uP to route ctrl queue compl
to rdma rspq
- relinquishes mutex_lock
- acquires the mutex_lock
- enable_rx()
- set FULL_INIT_DONE
- relinquishes mutex_lock
This patch fixes the above issue.
Fixes: e7519f9926f1('cxgb4: avoid enabling napi twice to the same queue')
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 089bc0143f upstream.
Rather than constructing a local structure instance on the stack, fill
the fields directly on the shared ring, just like other backends do.
Build on the fact that all response structure flavors are actually
identical (the old code did make this assumption too).
This is XSA-216.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4646441130 upstream.
Today disconnecting xen-blkback is broken in case there are still
I/Os in flight: xen_blkif_disconnect() will bail out early without
releasing all resources in the hope it will be called again when
the last request has terminated. This, however, won't happen as
xen_blkif_free() won't be called on termination of the last running
request: xen_blkif_put() won't decrement the blkif refcnt to 0 as
xen_blkif_disconnect() didn't finish before thus some xen_blkif_put()
calls in xen_blkif_disconnect() didn't happen.
To solve this deadlock xen_blkif_disconnect() and
xen_blkif_alloc_rings() shouldn't use xen_blkif_put() and
xen_blkif_get() but use some other way to do their accounting of
resources.
This at once fixes another error in xen_blkif_disconnect(): when it
returned early with -EBUSY for another ring than 0 it would call
xen_blkif_put() again for already handled rings on a subsequent call.
This will lead to inconsistencies in the refcnt handling.
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38b8f82386 upstream.
The register offset for the lcd1-ch1 clock was incorrectly pointing to
the lcd0-ch1 clock. This resulted in the lcd0-ch1 clock being disabled
when the clk core disables unused clocks. This then stops the simplefb
HDMI output path.
Reported-by: Bob Ham <rah@settrans.net>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31574d321c upstream.
The current code passes the address of tpm_chip as the argument to
dev_get_drvdata() without prior NULL check in
tpm_ibmvtpm_get_desired_dma. This resulted an oops during kernel
boot when vTPM is enabled in Power partition configured in active
memory sharing mode.
The vio_driver's get_desired_dma() is called before the probe(), which
for vtpm is tpm_ibmvtpm_probe, and it's this latter function that
initializes the driver and set data. Attempting to get data before
the probe() caused the problem.
This patch adds a NULL check to the tpm_ibmvtpm_get_desired_dma.
fixes: 9e0d39d8a6 ("tpm: Remove useless priv field in struct tpm_vendor_specific")
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkine <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 990758c53e upstream.
'cdev->os_desc_req' has been allocated with 'usb_ep_alloc_request()' so
'usb_ep_free_request()' should be used to free it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 948588e25b upstream.
Starting from MPU6500, accelerometer dlpf is set in a separate
register named ACCEL_CONFIG_2.
Add this new register in the map and set it for the corresponding
chips.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16443a034 upstream.
Using the syzkaller kernel fuzzer, Andrey Konovalov generated the
following error in gadgetfs:
> BUG: KASAN: use-after-free in __lock_acquire+0x3069/0x3690
> kernel/locking/lockdep.c:3246
> Read of size 8 at addr ffff88003a2bdaf8 by task kworker/3:1/903
>
> CPU: 3 PID: 903 Comm: kworker/3:1 Not tainted 4.12.0-rc4+ #35
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
> Workqueue: usb_hub_wq hub_event
> Call Trace:
> __dump_stack lib/dump_stack.c:16 [inline]
> dump_stack+0x292/0x395 lib/dump_stack.c:52
> print_address_description+0x78/0x280 mm/kasan/report.c:252
> kasan_report_error mm/kasan/report.c:351 [inline]
> kasan_report+0x230/0x340 mm/kasan/report.c:408
> __asan_report_load8_noabort+0x19/0x20 mm/kasan/report.c:429
> __lock_acquire+0x3069/0x3690 kernel/locking/lockdep.c:3246
> lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855
> __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
> _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151
> spin_lock include/linux/spinlock.h:299 [inline]
> gadgetfs_suspend+0x89/0x130 drivers/usb/gadget/legacy/inode.c:1682
> set_link_state+0x88e/0xae0 drivers/usb/gadget/udc/dummy_hcd.c:455
> dummy_hub_control+0xd7e/0x1fb0 drivers/usb/gadget/udc/dummy_hcd.c:2074
> rh_call_control drivers/usb/core/hcd.c:689 [inline]
> rh_urb_enqueue drivers/usb/core/hcd.c:846 [inline]
> usb_hcd_submit_urb+0x92f/0x20b0 drivers/usb/core/hcd.c:1650
> usb_submit_urb+0x8b2/0x12c0 drivers/usb/core/urb.c:542
> usb_start_wait_urb+0x148/0x5b0 drivers/usb/core/message.c:56
> usb_internal_control_msg drivers/usb/core/message.c:100 [inline]
> usb_control_msg+0x341/0x4d0 drivers/usb/core/message.c:151
> usb_clear_port_feature+0x74/0xa0 drivers/usb/core/hub.c:412
> hub_port_disable+0x123/0x510 drivers/usb/core/hub.c:4177
> hub_port_init+0x1ed/0x2940 drivers/usb/core/hub.c:4648
> hub_port_connect drivers/usb/core/hub.c:4826 [inline]
> hub_port_connect_change drivers/usb/core/hub.c:4999 [inline]
> port_event drivers/usb/core/hub.c:5105 [inline]
> hub_event+0x1ae1/0x3d40 drivers/usb/core/hub.c:5185
> process_one_work+0xc08/0x1bd0 kernel/workqueue.c:2097
> process_scheduled_works kernel/workqueue.c:2157 [inline]
> worker_thread+0xb2b/0x1860 kernel/workqueue.c:2233
> kthread+0x363/0x440 kernel/kthread.c:231
> ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:424
>
> Allocated by task 9958:
> save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
> save_stack+0x43/0xd0 mm/kasan/kasan.c:513
> set_track mm/kasan/kasan.c:525 [inline]
> kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:617
> kmem_cache_alloc_trace+0x87/0x280 mm/slub.c:2745
> kmalloc include/linux/slab.h:492 [inline]
> kzalloc include/linux/slab.h:665 [inline]
> dev_new drivers/usb/gadget/legacy/inode.c:170 [inline]
> gadgetfs_fill_super+0x24f/0x540 drivers/usb/gadget/legacy/inode.c:1993
> mount_single+0xf6/0x160 fs/super.c:1192
> gadgetfs_mount+0x31/0x40 drivers/usb/gadget/legacy/inode.c:2019
> mount_fs+0x9c/0x2d0 fs/super.c:1223
> vfs_kern_mount.part.25+0xcb/0x490 fs/namespace.c:976
> vfs_kern_mount fs/namespace.c:2509 [inline]
> do_new_mount fs/namespace.c:2512 [inline]
> do_mount+0x41b/0x2d90 fs/namespace.c:2834
> SYSC_mount fs/namespace.c:3050 [inline]
> SyS_mount+0xb0/0x120 fs/namespace.c:3027
> entry_SYSCALL_64_fastpath+0x1f/0xbe
>
> Freed by task 9960:
> save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
> save_stack+0x43/0xd0 mm/kasan/kasan.c:513
> set_track mm/kasan/kasan.c:525 [inline]
> kasan_slab_free+0x72/0xc0 mm/kasan/kasan.c:590
> slab_free_hook mm/slub.c:1357 [inline]
> slab_free_freelist_hook mm/slub.c:1379 [inline]
> slab_free mm/slub.c:2961 [inline]
> kfree+0xed/0x2b0 mm/slub.c:3882
> put_dev+0x124/0x160 drivers/usb/gadget/legacy/inode.c:163
> gadgetfs_kill_sb+0x33/0x60 drivers/usb/gadget/legacy/inode.c:2027
> deactivate_locked_super+0x8d/0xd0 fs/super.c:309
> deactivate_super+0x21e/0x310 fs/super.c:340
> cleanup_mnt+0xb7/0x150 fs/namespace.c:1112
> __cleanup_mnt+0x1b/0x20 fs/namespace.c:1119
> task_work_run+0x1a0/0x280 kernel/task_work.c:116
> exit_task_work include/linux/task_work.h:21 [inline]
> do_exit+0x18a8/0x2820 kernel/exit.c:878
> do_group_exit+0x14e/0x420 kernel/exit.c:982
> get_signal+0x784/0x1780 kernel/signal.c:2318
> do_signal+0xd7/0x2130 arch/x86/kernel/signal.c:808
> exit_to_usermode_loop+0x1ac/0x240 arch/x86/entry/common.c:157
> prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
> syscall_return_slowpath+0x3ba/0x410 arch/x86/entry/common.c:263
> entry_SYSCALL_64_fastpath+0xbc/0xbe
>
> The buggy address belongs to the object at ffff88003a2bdae0
> which belongs to the cache kmalloc-1024 of size 1024
> The buggy address is located 24 bytes inside of
> 1024-byte region [ffff88003a2bdae0, ffff88003a2bdee0)
> The buggy address belongs to the page:
> page:ffffea0000e8ae00 count:1 mapcount:0 mapping: (null)
> index:0x0 compound_mapcount: 0
> flags: 0x100000000008100(slab|head)
> raw: 0100000000008100 0000000000000000 0000000000000000 0000000100170017
> raw: ffffea0000ed3020 ffffea0000f5f820 ffff88003e80efc0 0000000000000000
> page dumped because: kasan: bad access detected
>
> Memory state around the buggy address:
> ffff88003a2bd980: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> ffff88003a2bda00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> >ffff88003a2bda80: fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb fb
> ^
> ffff88003a2bdb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ffff88003a2bdb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ==================================================================
What this means is that the gadgetfs_suspend() routine was trying to
access dev->lock after it had been deallocated. The root cause is a
race in the dummy_hcd driver; the dummy_udc_stop() routine can race
with the rest of the driver because it contains no locking. And even
when proper locking is added, it can still race with the
set_link_state() function because that function incorrectly drops the
private spinlock before invoking any gadget driver callbacks.
The result of this race, as seen above, is that set_link_state() can
invoke a callback in gadgetfs even after gadgetfs has been unbound
from dummy_hcd's UDC and its private data structures have been
deallocated.
include/linux/usb/gadget.h documents that the ->reset, ->disconnect,
->suspend, and ->resume callbacks may be invoked in interrupt context.
In general this is necessary, to prevent races with gadget driver
removal. This patch fixes dummy_hcd to retain the spinlock across
these calls, and it adds a spinlock acquisition to dummy_udc_stop() to
prevent the race.
The net2280 driver makes the same mistake of dropping the private
spinlock for its ->disconnect and ->reset callback invocations. The
patch fixes it too.
Lastly, since gadgetfs_suspend() may be invoked in interrupt context,
it cannot assume that interrupts are enabled when it runs. It must
use spin_lock_irqsave() instead of spin_lock_irq(). The patch fixes
that bug as well.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2f48f05cd upstream.
When plugging an USB webcam I see the following message:
[106385.615559] xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[106390.583860] handle_tx_event: 913 callbacks suppressed
With this patch applied, I get no more printing of this message.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b72eb8435b upstream.
xHCI host controllers can have both USB 3.1 and 3.0 extended speed
protocol lists. If the USB3.1 speed is parsed first and 3.0 second then
the minor revision supported will be overwritten by the 3.0 speeds and
the USB3 roothub will only show support for USB 3.0 speeds.
This was the case with a xhci controller with the supported protocol
capability listed below.
In xhci-mem.c, the USB 3.1 speed is parsed first, the min_rev of usb3_rhub
is set as 0x10. And then USB 3.0 is parsed. However, the min_rev of
usb3_rhub will be changed to 0x00. If USB 3.1 device is connected behind
this host controller, the speed of USB 3.1 device just reports 5G speed
using lsusb.
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00 01 08 00 00 00 00 00 40 00 00 00 00 00 00 00 00
10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20 02 08 10 03 55 53 42 20 01 02 00 00 00 00 00 00 //USB 3.1
30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40 02 08 00 03 55 53 42 20 03 06 00 00 00 00 00 00 //USB 3.0
50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60 02 08 00 02 55 53 42 20 09 0E 19 00 00 00 00 00 //USB 2.0
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
This patch fixes the issue by only owerwriting the minor revision if
it is higher than the existing one.
[reword commit message -Mathias]
Signed-off-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 816c9311f1 upstream.
This function only has one caller. Freeing "vdev" here leads to a use
after free bug. There are several other error paths in this function
but this is the only one which frees "vdev". It looks like the kfree()
can be safely removed.
Fixes: 61e9c905df ("misc: mic: Enable VOP host side functionality")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1427228d58 upstream.
This fixes the below crash when ath10k probe firmware fails, NAPI polling tries
to access a rx ring resource which was never allocated. An easy way to
reproduce this is easy to remove all the firmware files, load ath10k modules
and ath10k will crash when calling 'rmmod ath10k_pci'. The fix is to call
napi_enable() from ath10k_pci_hif_start() so that it matches with
napi_disable() being called from ath10k_pci_hif_stop().
Big thanks to Mohammed Shafi Shajakhan who debugged this and provided first
version of the fix. In this patch I just fix the actual problem in pci.c
instead of having a workaround in core.c.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: __ath10k_htt_rx_ring_fill_n+0x19/0x230 [ath10k_core]
__ath10k_htt_rx_ring_fill_n+0x19/0x230 [ath10k_core]
Call Trace:
[<ffffffffa113ec62>] ath10k_htt_rx_msdu_buff_replenish+0x42/0x90
[ath10k_core]
[<ffffffffa113f393>] ath10k_htt_txrx_compl_task+0x433/0x17d0
[ath10k_core]
[<ffffffff8114406d>] ? __wake_up_common+0x4d/0x80
[<ffffffff811349ec>] ? cpu_load_update+0xdc/0x150
[<ffffffffa119301d>] ? ath10k_pci_read32+0xd/0x10 [ath10k_pci]
[<ffffffffa1195b17>] ath10k_pci_napi_poll+0x47/0x110 [ath10k_pci]
[<ffffffff817863af>] net_rx_action+0x20f/0x370
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: 3c97f5de1f ("ath10k: implement NAPI support")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd14a3e9b9 upstream.
The timeout for BULK packets was 300ms which is a long time if other
endpoints or devices are waiting for their turn. Changing it to 50ms
greatly increased the overall performance for multi-endpoint devices.
Fixes: 5d3043586d ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f873d857b upstream.
If multiple endpoints on a single device have pending IN URBs and one
endpoint times out due to NAKs (perfectly legal), select a different
endpoint URB to try.
The existing code only checked to see another device address has pending
URBs and ignores other IN endpoints on the current device address. This
leads to endpoints never getting serviced if one endpoint is using NAK as
a flow control method.
Fixes: 5d3043586d ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d81182ce30 upstream.
Flag the first and only port as removable while also leaving the
remaining bits (including the reserved bit zero) unset in accordance
with the specifications:
"Within a byte, if no port exists for a given location, the bit
field representing the port characteristics shall be 0."
Also add a comment marking the legacy PortPwrCtrlMask field.
Fixes: 1cd8fd2887 ("usb: gadget: dummy_hcd: add SuperSpeed support")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6830733d53 upstream.
The driver uses a relatively large data structure on the stack, which
showed up on my radar as we get a warning with the "latent entropy"
GCC plugin:
drivers/media/usb/pvrusb2/pvrusb2-eeprom.c:153:1: error: the frame size of 1376 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
The warning is usually hidden as we raise the warning limit to 2048
when the plugin is enabled, but I'd like to lower that again in the
future, and making this function smaller helps to do that without
build regressions.
Further analysis shows that putting an 'i2c_client' structure on
the stack is not really supported, as the embedded 'struct device'
is not initialized here, and we are only saved by the fact that
the function that is called here does not use the pointer at all.
Fixes: d855497edb ("V4L/DVB (4228a): pvrusb2 to kernel 2.6.18")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec963b412a upstream.
Fix up the root-hub descriptor to accommodate the variable-length
DeviceRemovable and PortPwrCtrlMask fields, while marking all ports as
removable (and leaving the reserved bit zero unset).
Also add a build-time constraint on VHCI_HC_PORTS which must never be
greater than USB_MAXCHILDREN (but this was only enforced through a
KConfig constant).
This specifically fixes the descriptor layout whenever VHCI_HC_PORTS is
greater than seven (default is 8).
Fixes: 04679b3489 ("Staging: USB/IP: add client driver")
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93491ced3c upstream.
Add define for the maximum number of ports on a SuperSpeed hub as per
USB 3.1 spec Table 10-5, and use it when verifying the retrieved hub
descriptor.
This specifically avoids benign attempts to update the DeviceRemovable
mask for non-existing ports (should we get that far).
Fixes: dbe79bbe9d ("USB 3.0 Hub Changes")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 940f538a10 upstream.
This controller disallows to change the PIPE until reading/writing
a packet finishes. However. the previous code is not enough to hold
the lock in some functions. So, this patch fixes it.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 067d6fdc55 upstream.
This patch fixes an issue that this driver is possible to cause
deadlock by double-spinclocked in renesas_usb3_stop_controller().
So, this patch removes spinlock API calling in renesas_usb3_stop().
(In other words, the previous code had a redundant lock.)
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdc876877e upstream.
This patch fixes an issue that this driver is possible to access
the registers before pm_runtime_get_sync() if a gadget driver is
installed first. After that, oops happens on R-Car Gen3 environment.
To avoid it, this patch changes the pm_runtime call timing from
probe/remove to udc_start/udc_stop.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de8d6e02ef upstream.
The logic was broken as it failed to update the response length for
architectures with PAGE_SIZE larger than 4kB. As a result further
extension of the ucontext response struct would fail.
Fixes: d69e3bcf79 ('IB/mlx5: Mmap the HCA's core clock register to user-space')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ba5b437ef upstream.
We should be allocating enough information for a tiadc_device struct
which is about 400 bytes but instead we allocate enough for a second
iio_dev struct which is over 2000 bytes.
Fixes: fea89e2dfc ("iio: adc: ti_am335x_adc: use variable names for sizeof() operator")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6272c0de13 upstream.
According to the datasheet the RCO must be recalibrated
on every power-on-reset. Also remove mutex locking in the
calibration function since callers other than the probe
function (which doesn't need it) will have a lock.
Fixes: 24ddb0e4bb ("iio: Add AS3935 lightning sensor support")
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b211d48ab upstream.
Datasheet of each device (lps331ap, lps25h, lps001wp, lps22hb) says that
the pressure and temperature data is a 2's complement.
I'm sending this the slow way, as negative pressures on these are pretty
unusual and the nature of the fixing of multiple device introduction patches
will make it hard to apply to older kernels - Jonathan.
Fixes: 217494e5b7 ("iio:pressure: Add STMicroelectronics pressures driver")
Fixes: 2f5effcbd0 ("iio: pressure-core: st: Expand and rename LPS331AP's channel descriptor")
Fixes: 7885a8ce68 ("iio: pressure: st: Add support for new LPS001WP pressure sensor")
Fixes: e039e2f5b4 ("iio:st_pressure:initial lps22hb sensor support")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
