[ Upstream commit 7d7d065a5e ]
Chelsio cxgb4 HW is big-endian, hence there is need to properly
annotate r2 and stag fields as __be32 and not __u32 to fix the
following sparse warnings.
drivers/infiniband/hw/cxgb4/qp.c:614:16:
warning: incorrect type in assignment (different base types)
expected unsigned int [unsigned] [usertype] r2
got restricted __be32 [usertype] <noident>
drivers/infiniband/hw/cxgb4/qp.c:615:18:
warning: incorrect type in assignment (different base types)
expected unsigned int [unsigned] [usertype] stag
got restricted __be32 [usertype] <noident>
Cc: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca29fd7cce ]
When process the outbound packet of ipv6, we should assign the master
device to output device other than input device.
Signed-off-by: Keefe Liu <liuqifa@huawei.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f7f5551a7 upstream.
System may crash after unloading ipmi_si.ko module
because a timer may remain and fire after the module cleaned up resources.
cleanup_one_si() contains the following processing.
/*
* Make sure that interrupts, the timer and the thread are
* stopped and will not run again.
*/
if (to_clean->irq_cleanup)
to_clean->irq_cleanup(to_clean);
wait_for_timer_and_thread(to_clean);
/*
* Timeouts are stopped, now make sure the interrupts are off
* in the BMC. Note that timers and CPU interrupts are off,
* so no need for locks.
*/
while (to_clean->curr_msg || (to_clean->si_state != SI_NORMAL)) {
poll(to_clean);
schedule_timeout_uninterruptible(1);
}
si_state changes as following in the while loop calling poll(to_clean).
SI_GETTING_MESSAGES
=> SI_CHECKING_ENABLES
=> SI_SETTING_ENABLES
=> SI_GETTING_EVENTS
=> SI_NORMAL
As written in the code comments above,
timers are expected to stop before the polling loop and not to run again.
But the timer is set again in the following process
when si_state becomes SI_SETTING_ENABLES.
=> poll
=> smi_event_handler
=> handle_transaction_done
// smi_info->si_state == SI_SETTING_ENABLES
=> start_getting_events
=> start_new_msg
=> smi_mod_timer
=> mod_timer
As a result, before the timer set in start_new_msg() expires,
the polling loop may see si_state becoming SI_NORMAL
and the module clean-up finishes.
For example, hard LOCKUP and panic occurred as following.
smi_timeout was called after smi_event_handler,
kcs_event and hangs at port_inb()
trying to access I/O port after release.
[exception RIP: port_inb+19]
RIP: ffffffffc0473053 RSP: ffff88069fdc3d80 RFLAGS: 00000006
RAX: ffff8806800f8e00 RBX: ffff880682bd9400 RCX: 0000000000000000
RDX: 0000000000000ca3 RSI: 0000000000000ca3 RDI: ffff8806800f8e40
RBP: ffff88069fdc3d80 R8: ffffffff81d86dfc R9: ffffffff81e36426
R10: 00000000000509f0 R11: 0000000000100000 R12: 0000000000]:000000
R13: 0000000000000000 R14: 0000000000000246 R15: ffff8806800f8e00
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000
--- <NMI exception stack> ---
To fix the problem I defined a flag, timer_can_start,
as member of struct smi_info.
The flag is enabled immediately after initializing the timer
and disabled immediately before waiting for timer deletion.
Fixes: 0cfec916e8 ("ipmi: Start the timer and thread on internal msgs")
Signed-off-by: Yamazaki Masamitsu <m-yamazaki@ah.jp.nec.com>
[Adjusted for recent changes in the driver.]
[Some fairly major changes went into the IPMI driver in 4.15, so this
required a backport as the code had changed and moved to a different
file. The 4.14 version of this patch moved some code under an
if statement causing it to not apply to 4.7-4.13.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upsteam commit bc3ab70584 ]
Commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
reworked how secondary addresses are managed for qeth devices.
Instead of dropping & subsequently re-adding all addresses on every
ndo_set_rx_mode() call, qeth now keeps track of the addresses that are
currently registered with the HW.
On a ndo_set_rx_mode(), we thus only need to do (de-)registration
requests for the addresses that have actually changed.
On L3 devices, the lookup for IPv4 Multicast addresses checks the wrong
hashtable - and thus never finds a match. As a result, we first delete
*all* such addresses, and then re-add them again. So each set_rx_mode()
causes a short period where the IPv4 Multicast addresses are not
registered, and the card stops forwarding inbound traffic for them.
Fix this by setting the ->is_multicast flag on the lookup object, thus
enabling qeth_l3_ip_from_hash() to search the correct hashtable and
find a match there.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d69b1f1eb ]
Using GSO with small MTUs currently results in a substantial throughput
regression - which is caused by how qeth needs to map non-linear skbs
into its IO buffer elements:
compared to a linear skb, each GSO-segmented skb effectively consumes
twice as many buffer elements (ie two instead of one) due to the
additional header-only part. This causes the Output Queue to be
congested with low-utilized IO buffers.
Fix this as follows:
If the MSS is low enough so that a non-SG GSO segmentation produces
order-0 skbs (currently ~3500 byte), opt out from NETIF_F_SG. This is
where we anticipate the biggest savings, since an SG-enabled
GSO segmentation produces skbs that always consume at least two
buffer elements.
Larger MSS values continue to get a SG-enabled GSO segmentation, since
1) the relative overhead of the additional header-only buffer element
becomes less noticeable, and
2) the linearization overhead increases.
With the throughput regression fixed, re-enable NETIF_F_SG by default to
reap the significant CPU savings of GSO.
Fixes: 5722963a8e ("qeth: do not turn on SG per default")
Reported-by: Nils Hoppmann <niho@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0cbff6d454 ]
The current GSO skb size limit was copy&pasted over from the L3 path,
where it is needed due to a TSO limitation.
As L2 devices don't offer TSO support (and thus all GSO skbs are
segmented before they reach the driver), there's no reason to restrict
the stack in how large it may build the GSO skbs.
Fixes: d52aec97e5 ("qeth: enable scatter/gather in layer 2 mode")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45ab4b13e4 ]
The mss variable tracks the last max segment size sent to the TSO
engine. We do not update the hardware as long as we receive skb:s with
the same value in gso_size.
During a network device down/up cycle (mapped to stmmac_release() and
stmmac_open() callbacks) we issue a reset to the hardware and it
forgets the setting for mss. However we did not zero out our mss
variable so the next transmission of a gso packet happens with an
undefined hardware setting.
This triggers a hang in the TSO engine and eventuelly the netdev
watchdog will bark.
Fixes: f748be531d ("stmmac: support new GMAC4")
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a4abd7a80a ]
The qmi_wwan minidriver support a 'raw-ip' mode where frames are
received without any ethernet header. This causes alignment issues
because the skbs allocated by usbnet are "IP aligned".
Fix by allowing minidrivers to disable the additional alignment
offset. This is implemented using a per-device flag, since the same
minidriver also supports 'ethernet' mode.
Fixes: 32f7adf633 ("net: qmi_wwan: support "raw IP" mode")
Reported-and-tested-by: Jay Foster <jay@systech.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83cf79a2fe ]
When the allocation of the addr buffer fails, we need to free
our refcount on the inetdevice before returning.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9409e7f08 ]
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel development
board (EVB). The USB id is added to qmi_wwan.c to allow QMI
communication with the BG96.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31fde034a8 ]
The UMR's QP is created by calling mlx5_ib_create_qp directly, and
therefore the send CQ and the recv CQ on the ibqp weren't assigned.
Assign them right after calling the mlx5_ib_create_qp to assure
that any access to those pointers will work as expected and won't
crash the system as might happen as part of reset flow.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f22a1d87c ]
Maximal message should be used as a limit to the max message payload allowed,
without the headers. The ConnectX-3 check is done against this value includes
the headers. When the payload is 4K this will cause the NIC to drop packets.
Increase maximal message to 8K as workaround, this shouldn't change current
behaviour because we continue to set the MTU to 4k.
To reproduce;
set MTU to 4296 on the corresponding interface, for example:
ifconfig eth0 mtu 4296 (both server and client)
On server:
ib_send_bw -c UD -d mlx4_0 -s 4096 -n 1000000 -i1 -m 4096
On client:
ib_send_bw -d mlx4_0 -c UD <server_ip> -s 4096 -n 1000000 -i 1 -m 4096
Fixes: 6e0d733d92 ("IB/mlx4: Allow 4K messages for UD QPs")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bde533f2ea ]
atm_dev_register() can fail here and passed parameters to free irq
which is not initialised. Initialization of 'dev->irq' happened after
the 'goto out_free_irq'. So using 'irq' insted of 'dev->irq' in
free_irq().
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 67bd523861 ]
hwsim_new_radio_nl() now copies the name attribute in order to add a
null-terminator. mac80211_hwsim_new_radio() (indirectly) copies it
again into the net_device structure, so the first copy is not used or
freed later. Free the first copy before returning.
Fixes: ff4dd73dd2 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e61555c29c ]
The MTR_DRAM_WIDTH macro returns the data width. It is sometimes used
as if it returned a boolean true if the width if 8. Fix the tests where
MTR_DRAM_WIDTH is misused.
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170309011809.8340-1-jeremy.lefaure@lse.epita.fr
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0bc315381f ]
zram can handle at most SECTORS_PER_PAGE sectors in a bio's bvec. When using
the NVMe over Fabrics loopback target which potentially sends a huge bulk of
pages attached to the bio's bvec this results in a kernel panic because of
array out of bounds accesses in zram_decompress_page().
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2501c1bb05 ]
While modifying the driver to use the STOP interrupt, the completion of the
intermediate transfers need to wake the driver back up in order to initiate
the next transfer (restart condition). Otherwise you get never ending
interrupts and only the first transfer sent.
Fixes: 71ccea095e ("i2c: riic: correctly finish transfers")
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07de4bc88c ]
In a regular interrupt handler driver was finishing the crypt/decrypt
request by calling complete on crypto request. This is disallowed since
converting to skcipher in commit b286d8b1a6 ("crypto: skcipher - Add
skcipher walk interface") and causes a warning:
WARNING: CPU: 0 PID: 0 at crypto/skcipher.c:430 skcipher_walk_first+0x13c/0x14c
The interrupt is marked shared but in fact there are no other users
sharing it. Thus the simplest solution seems to be to just use a
threaded interrupt handler, after converting it to oneshot.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 068d9f90a6 ]
The amount of TX/RX buffers that the vNIC driver currently allocates
is different from the amount agreed upon in negotiation with firmware.
Correct that by allocating the requested number of buffers confirmed
by firmware.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 142c0ac445 ]
Use a counter to track the number of outstanding transmissions sent
that have not received completions. If the counter reaches the maximum
number of queue entries, stop transmissions on that queue. As we receive
more completions from firmware, wake the queue once the counter reaches
an acceptable level.
This patch prevents hardware/firmware TX queue from filling up and
and generating errors. Since incorporating this fix, internal testing
has reported that these firmware errors have stopped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78d5505432 ]
On failure to configure a VF MAC/VLAN filter we should not attempt to
rollback filters that we failed to configure with -EEXIST.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 83bd9eb8fc ]
VFs are currently missing the VLAN filtering feature, because we were
checking the PF's acquire response before actually performing the acquire.
Fix it by setting the feature flag later when we have the PF response.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22118d861c ]
It is too late to check for the limit of the number of VF multicast
addresses after they have already been copied to the req->multicast[]
array, possibly overflowing it.
Do the check before copying.
Also fix the error path to not skip unlocking vf2pf_mutex.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 466e8bf10a ]
It is possible to crash the kernel by accessing a PTP device while its
associated bnx2x interface is down. Before the interface is brought up,
the timecounter is not initialized, so accessing it results in NULL
dereference.
Fix it by checking if the interface is up.
Use -ENETDOWN as the error code when the interface is down.
-EFAULT in bnx2x_ptp_adjfreq() did not seem right.
Tested using phc_ctl get/set/adj/freq commands.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4b9de5da7e ]
The 'size' variable is unsigned according to the dt-bindings.
As this variable is used as integer in other places, create a new variable
that allows to fix the following sparse issue (-Wtypesign):
drivers/irqchip/irq-crossbar.c:279:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:279:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:279:52: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d181531bc ]
if REG_VPI fails, the driver was incorrectly issuing INIT_VFI
(a SLI4 command) on a SLI3 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 23456565ac ]
Recent printk changes for KERN_CONT cause this logging to be defectively
emitted on multiple lines. Fix it.
Also reduces object size a trivial amount.
$ size drivers/scsi/qla2xxx/qla_dbg.o*
text data bss dec hex filename
39125 0 0 39125 98d5 drivers/scsi/qla2xxx/qla_dbg.o.new
39164 0 0 39164 98fc drivers/scsi/qla2xxx/qla_dbg.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0580b762a4 ]
ata_sff_qc_issue() expects upper layers to never issue commands on a
command protocol that it doesn't implement. While the assumption
holds fine with the usual IO path, nothing filters based on the
command protocol in the passthrough path (which was added later),
allowing the warning to be tripped with a passthrough command with the
right (well, wrong) protocol.
Failing with AC_ERR_SYSTEM is the right thing to do anyway. Remove
the unnecessary WARN.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Link: http://lkml.kernel.org/r/CACT4Y+bXkvevNZU8uP6X0QVqsj6wNoUA_1exfTSOzc+SmUtMOA@mail.gmail.com
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef5e2fa9f6 ]
In the function scan_dma_completions() there is a reusage of tmp
variable. That coused a wrong value being used in some case when
reading a short packet terminated transaction from an endpoint,
in 2 concecutive reads.
This was my logic for the patch:
The req->td->dmadesc equals to 0 iff:
-- There was a transaction ending with a short packet, and
-- The read() to read it was shorter than the transaction length, and
-- The read() to complete it is longer than the residue.
I believe this is true from the printouts of various cases,
but I can't be positive it is correct.
Entering this if, there should be no more data in the endpoint
(a short packet terminated the transaction).
If there is, the transaction wasn't really done and we should exit and
wait for it to finish entirely. That is the inner if.
That inner if should never happen, but it is there to be on the safe
side. That is why it is marked with the comment /* paranoia */.
The size of the data available in the endpoint is ep->dma->dmacount
and it is read to tmp.
This entire clause is based on my own educated guesses.
If we passed that inner if without breaking in the original code,
than tmp & DMA_BYTE_MASK_COUNT== 0.
That means we will always pass dma bytes count of 0 to dma_done(),
meaning all the requested bytes were read.
dma_done() reports back to the upper layer that the request (read())
was done and how many bytes were read.
In the original code that would always be the request size,
regardless of the actual size of the data.
That did not make sense to me at all.
However, the original value of tmp is req->td->dmacount,
which is the dmacount value when the request's dma transaction was
finished. And that is a much more reasonable value to report back to
the caller.
To recreate the problem:
Read from a bulk out endpoint in a loop, 1024 * n bytes in each
iteration.
Connect the PLX to a host you can control.
Send to that endpoint 1024 * n + x bytes,
such that 0 < x < 1024 * n and (x % 1024) != 0
You would expect the first read() to return 1024 * n
and the second read() to return x.
But you will get the first read to return 1024 * n
and the second one to return 1024 * n.
That is true for every positive integer n.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Raz Manor <Raz.Manor@valens.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df7545719a ]
A call usb_put_phy(udc->transceiver) must be tested for a valid pointer.
Use an already existing test for usb_unregister_notifier call.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6e7aeeaf2 ]
'kbuf' is allocated just a few lines above using 'memdup_user()'.
If the 'if (dev->buf)' test fails, this memory is never released.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38355b2a44 ]
When binding a gadget to a device, "name" is stored in gi->udc_name, but
this does not happen when unregistering and the string is leaked.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f2f10b7e72 ]
Add support for media keys on the keyboard that comes with the
Asus V221ID and ZN241IC All In One computers.
The keys to support here are WLAN, BRIGHTNESSDOWN and BRIGHTNESSUP.
This device is not visibly branded as Chicony, and the USB Vendor ID
suggests that it is a JESS device. However this seems like the right place
to put it: the usage codes are identical to the currently supported
devices, and this driver already supports the ASUS AIO keyboard AK1D.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f759921cfb ]
When a threaded irq handler is chained attached to one of the gpio
pins when configure for level irq the altera_gpio_irq_leveL_high_handler
does not mask the interrupt while being handled by the chained irq.
This resulting in the threaded irq not getting enough cycles to complete
quickly enough before the irq was disabled as faulty. handle_level_irq
should be used in this situation instead of handle_simple_irq.
In gpiochip_irqchip_add set default handler to handle_bad_irq as
per Documentation/gpio/driver.txt. Then set the correct handler in
the set_type callback.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3acc69608 upstream.
The specification says that the Reserved1 field in OS_DESC_EXT_COMPAT
must have the value "1", but when this feature was first implemented we
rejected any non-zero values.
This was adjusted to accept all non-zero values (while now rejecting
zero) in commit 53642399aa ("usb: gadget: f_fs: Fix wrong check on
reserved1 of OS_DESC_EXT_COMPAT"), but that breaks any userspace
programs that worked previously by returning EINVAL when Reserved1 == 0
which was previously the only value that succeeded!
If we just set the field to "1" ourselves, both old and new userspace
programs continue to work correctly and, as a bonus, old programs are
now compliant with the specification without having to fix anything
themselves.
Fixes: 53642399aa ("usb: gadget: f_fs: Fix wrong check on reserved1 of OS_DESC_EXT_COMPAT")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
