commit c93637e6a4 upstream.
Avoid large backtrace, it is sufficient to warn the user that there has
been a link problem. Either the link has failed and the system is in need
of maintenance, or the link continues to work and user has been informed.
The message from the warning can be looked up in the sources.
This makes an actual link issue less verbose.
First of all, this controller has a limitation in that the controller
driver has to assist the hardware with transition to L1 link state by
writing L1IATN to PMCTRL register, the L1 and L0 link state switching
is not fully automatic on this controller.
In case of an ASMedia ASM1062 PCIe SATA controller which does not support
ASPM, on entry to suspend or during platform pm_test, the SATA controller
enters D3hot state and the link enters L1 state. If the SATA controller
wakes up before rcar_pcie_wakeup() was called and returns to D0, the link
returns to L0 before the controller driver even started its transition to
L1 link state. At this point, the SATA controller did send an PM_ENTER_L1
DLLP to the PCIe controller and the PCIe controller received it, and the
PCIe controller did set PMSR PMEL1RX bit.
Once rcar_pcie_wakeup() is called, if the link is already back in L0 state
and PMEL1RX bit is set, the controller driver has no way to determine if
it should perform the link transition to L1 state, or treat the link as if
it is in L0 state. Currently the driver attempts to perform the transition
to L1 link state unconditionally, which in this specific case fails with a
PMSR L1FAEG poll timeout, however the link still works as it is already
back in L0 state.
Reduce this warning verbosity. In case the link is really broken, the
rcar_pcie_config_access() would fail, otherwise it will succeed and any
system with this controller and ASM1062 can suspend without generating
a backtrace.
Fixes: 84b5761462 ("PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()")
Link: https://lore.kernel.org/linux-pci/20240511235513.77301-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b22f62724 upstream.
When bulk delete command is received in the rtnetlink_rcv_msg function,
if bulk delete is not supported, module_put is not called to release
the reference counting. As a result, module reference count is leaked.
Fixes: a6cec0bcd3 ("net: rtnetlink: add bulk delete support flag")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220815024629.240367-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47b2116e54 ]
After an bind/unbind cycle, the acm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
Call trace:
usb_ep_free_request+0x2c/0xec
gs_free_req+0x30/0x44
acm_bind+0x1b8/0x1f4
usb_add_function+0xcc/0x1f0
configfs_composite_bind+0x468/0x588
gadget_bind_driver+0x104/0x270
really_probe+0x190/0x374
__driver_probe_device+0xa0/0x12c
driver_probe_device+0x3c/0x218
__device_attach_driver+0x14c/0x188
bus_for_each_drv+0x10c/0x168
__device_attach+0xfc/0x198
device_initial_probe+0x14/0x24
bus_probe_device+0x94/0x11c
device_add+0x268/0x48c
usb_add_gadget+0x198/0x28c
dwc3_gadget_init+0x700/0x858
__dwc3_set_mode+0x3cc/0x664
process_scheduled_works+0x1d8/0x488
worker_thread+0x244/0x334
kthread+0x114/0x1bc
ret_from_fork+0x10/0x20
Fixes: 1f1ba11b64 ("usb gadget: issue notifications from ACM function")
Cc: stable@kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-4-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-4-4997bf277548@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75a5b8d4dd ]
After an bind/unbind cycle, the ncm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
Call trace:
usb_ep_free_request+0x2c/0xec
ncm_bind+0x39c/0x3dc
usb_add_function+0xcc/0x1f0
configfs_composite_bind+0x468/0x588
gadget_bind_driver+0x104/0x270
really_probe+0x190/0x374
__driver_probe_device+0xa0/0x12c
driver_probe_device+0x3c/0x218
__device_attach_driver+0x14c/0x188
bus_for_each_drv+0x10c/0x168
__device_attach+0xfc/0x198
device_initial_probe+0x14/0x24
bus_probe_device+0x94/0x11c
device_add+0x268/0x48c
usb_add_gadget+0x198/0x28c
dwc3_gadget_init+0x700/0x858
__dwc3_set_mode+0x3cc/0x664
process_scheduled_works+0x1d8/0x488
worker_thread+0x244/0x334
kthread+0x114/0x1bc
ret_from_fork+0x10/0x20
Fixes: 9f6ce4240a ("usb: gadget: f_ncm.c added")
Cc: stable@kernel.org
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-3-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-3-4997bf277548@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 201c53c687 ]
Introduce the free_usb_request() function that frees both the request's
buffer and the request itself.
This function serves as the cleanup callback for DEFINE_FREE() to enable
automatic, scope-based cleanup for usb_request pointers.
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-2-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-2-4997bf277548@google.com
Stable-dep-of: 75a5b8d4dd ("usb: gadget: f_ncm: Refactor bind path to use __free()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bfb1d99d96 ]
Gadget function drivers often have goto-based error handling in their
bind paths, which can be bug-prone. Refactoring these paths to use
__free() scope-based cleanup is desirable, but currently blocked.
The blocker is that usb_ep_free_request(ep, req) requires two
parameters, while the __free() mechanism can only pass a pointer to the
request itself.
Store an endpoint pointer in the struct usb_request. The pointer is
populated centrally in usb_ep_alloc_request() on every successful
allocation, making the request object self-contained.
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250916-ready-v1-1-4997bf277548@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250916-ready-v1-1-4997bf277548@google.com
Stable-dep-of: 75a5b8d4dd ("usb: gadget: f_ncm: Refactor bind path to use __free()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2eead19334 ]
Fix incorrect use of PTR_ERR_OR_ZERO() in topology_parse_cpu_capacity()
which causes the code to proceed with NULL clock pointers. The current
logic uses !PTR_ERR_OR_ZERO(cpu_clk) which evaluates to true for both
valid pointers and NULL, leading to potential NULL pointer dereference
in clk_get_rate().
Per include/linux/err.h documentation, PTR_ERR_OR_ZERO(ptr) returns:
"The error code within @ptr if it is an error pointer; 0 otherwise."
This means PTR_ERR_OR_ZERO() returns 0 for both valid pointers AND NULL
pointers. Therefore !PTR_ERR_OR_ZERO(cpu_clk) evaluates to true (proceed)
when cpu_clk is either valid or NULL, causing clk_get_rate(NULL) to be
called when of_clk_get() returns NULL.
Replace with !IS_ERR_OR_NULL(cpu_clk) which only proceeds for valid
pointers, preventing potential NULL pointer dereference in clk_get_rate().
Cc: stable <stable@kernel.org>
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: b8fe128dad ("arch_topology: Adjust initial CPU capacities with current freq")
Link: https://patch.msgid.link/20250923174308.1771906-1-kaushlendra.kumar@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 630785bfbe ]
The deprecation of the 'attr2' mount option in 6.18 wasn't entirely
successful because nobody noticed that the kernel never printed a
warning about attr2 being set in fstab if the only xfs filesystem is the
root fs; the initramfs mounts the root fs with no mount options; and the
init scripts only conveyed the fstab options by remounting the root fs.
Fix this by making it complain all the time.
Cc: stable@vger.kernel.org # v5.13
Fixes: 92cf7d3638 ("xfs: Skip repetitive warnings about mount options")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
[ Update existing xfs_fs_warn_deprecated() callers ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 42f9c66a6d ]
Tegra already defines all BARs except BAR0 as BAR_RESERVED. This is
sufficient for pci-epf-test to not allocate backing memory and to not call
set_bar() for those BARs. However, marking a BAR as BAR_RESERVED does not
mean that the BAR gets disabled.
The host side driver, pci_endpoint_test, simply does an ioremap for all
enabled BARs and will run tests against all enabled BARs, so it will run
tests against the BARs marked as BAR_RESERVED.
After running the BAR tests (which will write to all enabled BARs), the
inbound address translation is broken. This is because the tegra controller
exposes the ATU Port Logic Structure in BAR4, so when BAR4 is written, the
inbound address translation settings get overwritten.
To avoid this, implement the dw_pcie_ep_ops .init() callback and start off
by disabling all BARs (pci-epf-test will later enable/configure BARs that
are not defined as BAR_RESERVED).
This matches the behavior of other PCIe endpoint drivers: dra7xx, imx6,
layerscape-ep, artpec6, dw-rockchip, qcom-ep, rcar-gen4, and uniphier-ep.
With this, the PCI endpoint kselftest test case CONSECUTIVE_BAR_TEST (which
was specifically made to detect address translation issues) passes.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250922140822.519796-7-cassel@kernel.org
[ changed dw_pcie_ep_ops .init to .ep_init and exported dw_pcie_ep_reset_bar ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0a8f173d9d ]
The pmsr_lock spinlock used to be necessary to synchronize access to the
PMSR register, because that access could have been triggered from either
config space access in rcar_pcie_config_access() or an exception handler
rcar_pcie_aarch32_abort_handler().
The rcar_pcie_aarch32_abort_handler() case is no longer applicable since
commit 6e36203bc1 ("PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read
which triggered an exception"), which performs more accurate, controlled
invocation of the exception, and a fixup.
This leaves rcar_pcie_config_access() as the only call site from which
rcar_pcie_wakeup() is called. The rcar_pcie_config_access() can only be
called from the controller struct pci_ops .read and .write callbacks,
and those are serialized in drivers/pci/access.c using raw spinlock
'pci_lock' . It should be noted that CONFIG_PCI_LOCKLESS_CONFIG is never
set on this platform.
Since the 'pci_lock' is a raw spinlock , and the 'pmsr_lock' is not a
raw spinlock, this constellation triggers 'BUG: Invalid wait context'
with CONFIG_PROVE_RAW_LOCK_NESTING=y .
Remove the pmsr_lock to fix the locking.
Fixes: a115b1bd3a ("PCI: rcar: Add L1 link state fix into data abort hook")
Reported-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Reported-by: Thuan Nguyen <thuan.nguyen-hong@banvien.com.vn>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250909162707.13927-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84b5761462 ]
In case the controller is transitioning to L1 in rcar_pcie_config_access(),
any read/write access to PCIECDR triggers asynchronous external abort. This
is because the transition to L1 link state must be manually finished by the
driver. The PCIe IP can transition back from L1 state to L0 on its own.
Avoid triggering the abort in rcar_pcie_config_access() by checking whether
the controller is in the transition state, and if so, finish the transition
right away. This prevents a lot of unnecessary exceptions, although not all
of them.
Link: https://lore.kernel.org/r/20220312212349.781799-1-marek.vasut@gmail.com
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Stable-dep-of: 0a8f173d9d ("PCI: rcar-host: Drop PMSR spinlock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f8c9ad46b0 ]
The return value from tegra_bpmp_transfer() indicates the success or
failure of the IPC transaction with BPMP. If the transaction succeeded, we
also need to check the actual command's result code.
If we don't have error handling for tegra_bpmp_transfer(), we will set the
pcie->ep_state to EP_STATE_ENABLED even when the tegra_bpmp_transfer()
command fails. Thus, the pcie->ep_state will get out of sync with reality,
and any further PERST# assert + deassert will be a no-op and will not
trigger the hardware initialization sequence.
This is because pex_ep_event_pex_rst_deassert() checks the current
pcie->ep_state, and does nothing if the current state is already
EP_STATE_ENABLED.
Thus, it is important to have error handling for tegra_bpmp_transfer(),
such that the pcie->ep_state can not get out of sync with reality, so that
we will try to initialize the hardware not only during the first PERST#
assert + deassert, but also during any succeeding PERST# assert + deassert.
One example where this fix is needed is when using a rock5b as host.
During the initial PERST# assert + deassert (triggered by the bootloader on
the rock5b) pex_ep_event_pex_rst_deassert() will get called, but for some
unknown reason, the tegra_bpmp_transfer() call to initialize the PHY fails.
Once Linux has been loaded on the rock5b, the PCIe driver will once again
assert + deassert PERST#. However, without tegra_bpmp_transfer() error
handling, this second PERST# assert + deassert will not trigger the
hardware initialization sequence.
With tegra_bpmp_transfer() error handling, the second PERST# assert +
deassert will once again trigger the hardware to be initialized and this
time the tegra_bpmp_transfer() succeeds.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[cassel: improve commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250922140822.519796-8-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d5c4f5c7a ]
Assuming the disk layout as below,
disk0: 0 --- 0x00035abfff
disk1: 0x00035ac000 --- 0x00037abfff
disk2: 0x00037ac000 --- 0x00037ebfff
and we want to read data from offset=13568 having len=128 across the block
devices, we can illustrate the block addresses like below.
0 .. 0x00037ac000 ------------------- 0x00037ebfff, 0x00037ec000 -------
| ^ ^ ^
| fofs 0 13568 13568+128
| ------------------------------------------------------
| LBA 0x37e8aa9 0x37ebfa9 0x37ec029
--- map 0x3caa9 0x3ffa9
In this example, we should give the relative map of the target block device
ranging from 0x3caa9 to 0x3ffa9 where the length should be calculated by
0x37ebfff + 1 - 0x37ebfa9.
In the below equation, however, map->m_pblk was supposed to be the original
address instead of the one from the target block address.
- map->m_len = min(map->m_len, dev->end_blk + 1 - map->m_pblk);
Cc: stable@vger.kernel.org
Fixes: 71f2c82062 ("f2fs: multidevice: support direct IO")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
[ applied fix to f2fs_map_blocks() instead of f2fs_map_blocks_cached() ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4b47a8601b ]
Avoid a crash if a pNFS client should happen to send a LAYOUTCOMMIT
operation on a FlexFiles layout.
Reported-by: Robert Morris <rtm@csail.mit.edu>
Closes: https://lore.kernel.org/linux-nfs/152f99b2-ba35-4dec-93a9-4690e625dccd@oracle.com/T/#t
Cc: Thomas Haynes <loghyr@hammerspace.com>
Cc: stable@vger.kernel.org
Fixes: 9b9960a0ca ("nfsd: Add a super simple flex file server")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
[ removed struct svc_rqst parameter from nfsd4_ff_proc_layoutcommit ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56094ad3ea ]
When user calls open_by_handle_at() on some inode that is not cached, we
will create disconnected dentry for it. If such dentry is a directory,
exportfs_decode_fh_raw() will then try to connect this dentry to the
dentry tree through reconnect_path(). It may happen for various reasons
(such as corrupted fs or race with rename) that the call to
lookup_one_unlocked() in reconnect_one() will fail to find the dentry we
are trying to reconnect and instead create a new dentry under the
parent. Now this dentry will not be marked as disconnected although the
parent still may well be disconnected (at least in case this
inconsistency happened because the fs is corrupted and .. doesn't point
to the real parent directory). This creates inconsistency in
disconnected flags but AFAICS it was mostly harmless. At least until
commit f1ee616214 ("VFS: don't keep disconnected dentries on d_anon")
which removed adding of most disconnected dentries to sb->s_anon list.
Thus after this commit cleanup of disconnected dentries implicitely
relies on the fact that dput() will immediately reclaim such dentries.
However when some leaf dentry isn't marked as disconnected, as in the
scenario described above, the reclaim doesn't happen and the dentries
are "leaked". Memory reclaim can eventually reclaim them but otherwise
they stay in memory and if umount comes first, we hit infamous "Busy
inodes after unmount" bug. Make sure all dentries created under a
disconnected parent are marked as disconnected as well.
Reported-by: syzbot+1d79ebe5383fc016cf07@syzkaller.appspotmail.com
Fixes: f1ee616214 ("VFS: don't keep disconnected dentries on d_anon")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
[ relocated DCACHE_DISCONNECTED propagation from d_alloc_parallel() to d_alloc() ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6df8e84aa6 ]
The atomic variable vm_fault_info_updated is used to synchronize access to
adev->gmc.vm_fault_info between the interrupt handler and
get_vm_fault_info().
The default atomic functions like atomic_set() and atomic_read() do not
provide memory barriers. This allows for CPU instruction reordering,
meaning the memory accesses to vm_fault_info and the vm_fault_info_updated
flag are not guaranteed to occur in the intended order. This creates a
race condition that can lead to inconsistent or stale data being used.
The previous implementation, which used an explicit mb(), was incomplete
and inefficient. It failed to account for all potential CPU reorderings,
such as the access of vm_fault_info being reordered before the atomic_read
of the flag. This approach is also more verbose and less performant than
using the proper atomic functions with acquire/release semantics.
Fix this by switching to atomic_set_release() and atomic_read_acquire().
These functions provide the necessary acquire and release semantics,
which act as memory barriers to ensure the correct order of operations.
It is also more efficient and idiomatic than using explicit full memory
barriers.
Fixes: b97dfa27ef ("drm/amdgpu: save vm fault information for amdkfd")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com>
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ kept kgd_dev parameter and adev cast in amdgpu_amdkfd_gpuvm_get_vm_fault_info ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ed35b4d49 ]
The rcar_msi_irq_unmask() function may be called from a PCI driver
request_threaded_irq() function. This triggers kernel/irq/manage.c
__setup_irq() which locks raw spinlock &desc->lock descriptor lock
and with that descriptor lock held, calls rcar_msi_irq_unmask().
Since the &desc->lock descriptor lock is a raw spinlock, and the rcar_msi
.mask_lock is not a raw spinlock, this setup triggers 'BUG: Invalid wait
context' with CONFIG_PROVE_RAW_LOCK_NESTING=y.
Use scoped_guard() to simplify the locking.
Fixes: 83ed8d4fa6 ("PCI: rcar: Convert to MSI domains")
Reported-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Reported-by: Thuan Nguyen <thuan.nguyen-hong@banvien.com.vn>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250909162707.13927-2-marek.vasut+renesas@mailbox.org
[ replaced scoped_guard() with explicit raw_spin_lock_irqsave()/raw_spin_unlock_irqrestore() calls ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 32be3ca4cf ]
Don't deinitialize and reinitialize the HAL helpers. The dma memory is
deallocated and there is high possibility that we'll not be able to get
the same memory allocated from dma when there is high memory pressure.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.6
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org
Cc: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://patch.msgid.link/20250722053121.1145001-1-usama.anjum@collabora.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f842d3313b ]
The Cadence PCIe Controller integrated in the TI K3 SoCs supports both
Root-Complex and Endpoint modes of operation. The Glue Layer allows
"strapping" the Mode of operation of the Controller, the Link Speed
and the Link Width. This is enabled by programming the "PCIEn_CTRL"
register (n corresponds to the PCIe instance) within the CTRL_MMR
memory-mapped register space. The "reset-values" of the registers are
also different depending on the mode of operation.
Since the PCIe Controller latches onto the "reset-values" immediately
after being powered on, if the Glue Layer configuration is not done while
the PCIe Controller is off, it will result in the PCIe Controller latching
onto the wrong "reset-values". In practice, this will show up as a wrong
representation of the PCIe Controller's capability structures in the PCIe
Configuration Space. Some such capabilities which are supported by the PCIe
Controller in the Root-Complex mode but are incorrectly latched onto as
being unsupported are:
- Link Bandwidth Notification
- Alternate Routing ID (ARI) Forwarding Support
- Next capability offset within Advanced Error Reporting (AER) capability
Fix this by powering off the PCIe Controller before programming the "strap"
settings and powering it on after that. The runtime PM APIs namely
pm_runtime_put_sync() and pm_runtime_get_sync() will decrement and
increment the usage counter respectively, causing GENPD to power off and
power on the PCIe Controller.
Fixes: f3e25911a4 ("PCI: j721e: Add TI J721E PCIe driver")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250908120828.1471776-1-s-vadapalli@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 82c4be4168 ]
The ACSPCIE module is capable of driving the reference clock required by
the PCIe Endpoint device. It is an alternative to on-board and external
reference clock generators. Enabling the output from the ACSPCIE module's
PAD IO Buffers requires clearing the "PAD IO disable" bits of the
ACSPCIE_PROXY_CTRL register in the CTRL_MMR register space.
Add support to enable the ACSPCIE reference clock output using the optional
device-tree property "ti,syscon-acspcie-proxy-ctrl".
Link: https://lore.kernel.org/linux-pci/20240829105316.1483684-3-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: f842d3313b ("PCI: j721e: Fix programming sequence of "strap" settings")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26e5c67deb ]
I observed a hang when running generic/323 against a fuseblk server.
This test opens a file, initiates a lot of AIO writes to that file
descriptor, and closes the file descriptor before the writes complete.
Unsurprisingly, the AIO exerciser threads are mostly stuck waiting for
responses from the fuseblk server:
# cat /proc/372265/task/372313/stack
[<0>] request_wait_answer+0x1fe/0x2a0 [fuse]
[<0>] __fuse_simple_request+0xd3/0x2b0 [fuse]
[<0>] fuse_do_getattr+0xfc/0x1f0 [fuse]
[<0>] fuse_file_read_iter+0xbe/0x1c0 [fuse]
[<0>] aio_read+0x130/0x1e0
[<0>] io_submit_one+0x542/0x860
[<0>] __x64_sys_io_submit+0x98/0x1a0
[<0>] do_syscall_64+0x37/0xf0
[<0>] entry_SYSCALL_64_after_hwframe+0x4b/0x53
But the /weird/ part is that the fuseblk server threads are waiting for
responses from itself:
# cat /proc/372210/task/372232/stack
[<0>] request_wait_answer+0x1fe/0x2a0 [fuse]
[<0>] __fuse_simple_request+0xd3/0x2b0 [fuse]
[<0>] fuse_file_put+0x9a/0xd0 [fuse]
[<0>] fuse_release+0x36/0x50 [fuse]
[<0>] __fput+0xec/0x2b0
[<0>] task_work_run+0x55/0x90
[<0>] syscall_exit_to_user_mode+0xe9/0x100
[<0>] do_syscall_64+0x43/0xf0
[<0>] entry_SYSCALL_64_after_hwframe+0x4b/0x53
The fuseblk server is fuse2fs so there's nothing all that exciting in
the server itself. So why is the fuse server calling fuse_file_put?
The commit message for the fstest sheds some light on that:
"By closing the file descriptor before calling io_destroy, you pretty
much guarantee that the last put on the ioctx will be done in interrupt
context (during I/O completion).
Aha. AIO fgets a new struct file from the fd when it queues the ioctx.
The completion of the FUSE_WRITE command from userspace causes the fuse
server to call the AIO completion function. The completion puts the
struct file, queuing a delayed fput to the fuse server task. When the
fuse server task returns to userspace, it has to run the delayed fput,
which in the case of a fuseblk server, it does synchronously.
Sending the FUSE_RELEASE command sychronously from fuse server threads
is a bad idea because a client program can initiate enough simultaneous
AIOs such that all the fuse server threads end up in delayed_fput, and
now there aren't any threads left to handle the queued fuse commands.
Fix this by only using asynchronous fputs when closing files, and leave
a comment explaining why.
Cc: stable@vger.kernel.org # v2.6.38
Fixes: 5a18ec176c ("fuse: fix hang of single threaded fuseblk filesystem")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e26ee4efbc ]
This removed the need to pass isdir argument to fuse_put_file().
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Stable-dep-of: 26e5c67deb ("fuse: fix livelock in synchronous file put from fuseblk workers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 501302d5ce ]
When seq_nr wraps around, the next reorder job with seq 0 is hashed to
the first CPU in padata_do_serial(). Correspondingly, need reset pd->cpu
to the first one when pd->processed wraps around. Otherwise, if the
number of used CPUs is not a power of 2, padata_find_next() will be
checking a wrong list, hence deadlock.
Fixes: 6fc4dbcf02 ("padata: Replace delayed timer with immediate workqueue in padata_reorder")
Cc: <stable@vger.kernel.org>
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[ moved fix from padata_reorder() to padata_find_next() and adapted cpumask_next_wrap() to 4-argument signature ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0792c1984a ]
Rework the power management in inv_icm42600_core_probe() to use
devm_pm_runtime_set_active_enabled(), which simplifies the runtime PM
setup by handling activation and enabling in one step.
Remove the separate inv_icm42600_disable_pm callback, as it's no longer
needed with the devm-managed approach.
Using devm_pm_runtime_enable() also fixes the missing disable of
autosuspend.
Update inv_icm42600_disable_vddio_reg() to only disable the regulator if
the device is not suspended i.e. powered-down, preventing unbalanced
disables.
Also remove redundant error msg on regulator_disable(), the regulator
framework already emits an error message when regulator_disable() fails.
This simplifies the PM setup and avoids manipulating the usage counter
unnecessarily.
Fixes: 31c24c1e93 ("iio: imu: inv_icm42600: add core of new inv_icm42600 driver")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20250901-icm42pmreg-v3-1-ef1336246960@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 466f7a2fef ]
Do as in suspend, skip resume configuration steps if the device is already
pm_runtime suspended. This avoids reconfiguring a device that is already
in the correct low-power state and ensures that pm_runtime handles the
power state transitions properly.
Fixes: 31c24c1e93 ("iio: imu: inv_icm42600: add core of new inv_icm42600 driver")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20250901-icm42pmreg-v3-3-ef1336246960@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[ Placed early return before regulator enable instead of APEX wakeup logic ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d68886bae7 ]
The data type of loca_last_write_offset is newoffset4 and is switched
on a boolean value, no_newoffset, that indicates if a previous write
occurred or not. If no_newoffset is FALSE, an offset is not given.
This means that client does not try to update the file size. Thus,
server should not try to calculate new file size and check if it fits
into the segment range. See RFC 8881, section 12.5.4.2.
Sometimes the current incorrect logic may cause clients to hang when
trying to sync an inode. If layoutcommit fails, the client marks the
inode as dirty again.
Fixes: 9cf514ccfa ("nfsd: implement pNFS operations")
Cc: stable@vger.kernel.org
Co-developed-by: Konstantin Evtushenko <koevtushenko@yandex.com>
Signed-off-by: Konstantin Evtushenko <koevtushenko@yandex.com>
Signed-off-by: Sergey Bashirov <sergeybashirov@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
[ adapted for direct inode->i_mtime access and 2-parameter proc_layoutcommit callback ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 274365a51d ]
Remove dprintk in nfsd4_layoutcommit. These are not needed
in day to day usage, and the information is also available
in Wireshark when capturing NFS traffic.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sergey Bashirov <sergeybashirov@gmail.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stable-dep-of: d68886bae7 ("NFSD: Fix last write offset handling in layoutcommit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 832738e4b3 ]
Compilers may optimize the layout of C structures, so we should not rely
on sizeof struct and memcpy to encode and decode XDR structures. The byte
order of the fields should also be taken into account.
This patch adds the correct functions to handle the deviceid4 structure
and removes the pad field, which is currently not used by NFSD, from the
runtime state. The server's byte order is preserved because the deviceid4
blob on the wire is only used as a cookie by the client.
Signed-off-by: Sergey Bashirov <sergeybashirov@gmail.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stable-dep-of: d68886bae7 ("NFSD: Fix last write offset handling in layoutcommit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e747883c7d ]
When mounting file systems with a log that was dirtied on i386 on
other architectures or vice versa, log recovery is unhappy:
[ 11.068052] XFS (vdb): Torn write (CRC failure) detected at log block 0x2. Truncating head block from 0xc.
This is because the CRCs generated by i386 and other architectures
always diff. The reason for that is that sizeof(struct xlog_rec_header)
returns different values for i386 vs the rest (324 vs 328), because the
struct is not sizeof(uint64_t) aligned, and i386 has odd struct size
alignment rules.
This issue goes back to commit 13cdc853c519 ("Add log versioning, and new
super block field for the log stripe") in the xfs-import tree, which
adds log v2 support and the h_size field that causes the unaligned size.
At that time it only mattered for the crude debug only log header
checksum, but with commit 0e446be448 ("xfs: add CRC checks to the log")
it became a real issue for v5 file system, because now there is a proper
CRC, and regular builds actually expect it match.
Fix this by allowing checksums with and without the padding.
Fixes: 0e446be448 ("xfs: add CRC checks to the log")
Cc: <stable@vger.kernel.org> # v3.8
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
[ Adjust context and filenames ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b737f4ac1 ]
old_crc is a very misleading name. Rename it to expected_crc as that
described the usage much better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
Stable-dep-of: e747883c7d ("xfs: fix log CRC mismatches between i386 and other architectures")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9daa5a8795 upstream.
Starting with 'commit 2297791c92 ("s390/cio: dont unregister
subchannel from child-drivers")', cio no longer unregisters
subchannels when the attached device is invalid or unavailable.
As an unintended side-effect, the cio_ignore purge function no longer
removes subchannels for devices on the cio_ignore list if no CCW device
is attached. This situation occurs when a CCW device is non-operational
or unavailable
To ensure the same outcome of the purge function as when the
current cio_ignore list had been active during boot, update the purge
function to remove I/O subchannels without working CCW devices if the
associated device number is found on the cio_ignore list.
Fixes: 2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")
Suggested-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c33aa1804 upstream.
Neoverse-V3AE is also affected by erratum #3312417, as described in its
Software Developer Errata Notice (SDEN) document:
Neoverse V3AE (MP172) SDEN v9.0, erratum 3312417
https://developer.arm.com/documentation/SDEN-2615521/9-0/
Enable the workaround for Neoverse-V3AE, and document this.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
[ Ryan: Trivial backport ]
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bbf004c48 upstream.
Add cputype definitions for Neoverse-V3AE. These will be used for errata
detection in subsequent patches.
These values can be found in the Neoverse-V3AE TRM:
https://developer.arm.com/documentation/SDEN-2615521/9-0/
... in section A.6.1 ("MIDR_EL1, Main ID Register").
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
[ Ryan: Trivial backport ]
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7cbce761f upstream.
The Advantech 2-port serial card with PCI vendor=0x13fe and device=0x0018
has a 'XR17V35X' chip installed on the circuit board. Therefore, this
driver can be used instead of theu outdated out-of-tree driver from the
manufacturer.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20250924134115.2667650-1-fe@dev.tdt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8cc9e5fcb upstream.
The early error path in hdm_probe() can jump to err_free_mdev before
&mdev->dev has been initialized with device_initialize(). Calling
put_device(&mdev->dev) there triggers a device core WARN and ends up
invoking kref_put(&kobj->kref, kobject_release) on an uninitialized
kobject.
In this path the private struct was only kmalloc'ed and the intended
release is effectively kfree(mdev) anyway, so free it directly instead
of calling put_device() on an uninitialized device.
This removes the WARNING and fixes the pre-initialization error path.
Fixes: 97a6f772f3 ("drivers: most: add USB adapter driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Victoria Votokina <Victoria.Votokina@kaspersky.com>
Link: https://patch.msgid.link/20251010105241.4087114-3-Victoria.Votokina@kaspersky.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b12709026 upstream.
hdm_disconnect() calls most_deregister_interface(), which eventually
unregisters the MOST interface device with device_unregister(iface->dev).
If that drops the last reference, the device core may call release_mdev()
immediately while hdm_disconnect() is still executing.
The old code also freed several mdev-owned allocations in
hdm_disconnect() and then performed additional put_device() calls.
Depending on refcount order, this could lead to use-after-free or
double-free when release_mdev() ran (or when unregister paths also
performed puts).
Fix by moving the frees of mdev-owned allocations into release_mdev(),
so they happen exactly once when the device is truly released, and by
dropping the extra put_device() calls in hdm_disconnect() that are
redundant after device_unregister() and most_deregister_interface().
This addresses the KASAN slab-use-after-free reported by syzbot in
hdm_disconnect(). See report and stack traces in the bug link below.
Reported-by: syzbot+916742d5d24f6c254761@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Closes: https://syzkaller.appspot.com/bug?extid=916742d5d24f6c254761
Fixes: 97a6f772f3 ("drivers: most: add USB adapter driver")
Signed-off-by: Victoria Votokina <Victoria.Votokina@kaspersky.com>
Link: https://patch.msgid.link/20251010105241.4087114-2-Victoria.Votokina@kaspersky.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87b318ba81 upstream.
The comedi_buf_munge() function performs a modulo operation
`async->munge_chan %= async->cmd.chanlist_len` without first
checking if chanlist_len is zero. If a user program submits a command with
chanlist_len set to zero, this causes a divide-by-zero error when the device
processes data in the interrupt handler path.
Add a check for zero chanlist_len at the beginning of the
function, similar to the existing checks for !map and
CMDF_RAWDATA flag. When chanlist_len is zero, update
munge_count and return early, indicating the data was
handled without munging.
This prevents potential kernel panics from malformed user commands.
Reported-by: syzbot+f6c3c066162d2c43a66c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=f6c3c066162d2c43a66c
Cc: stable@vger.kernel.org
Signed-off-by: Deepanshu Kartikey <kartikey406@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20250924102639.1256191-1-kartikey406@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d90eeb8ecd upstream.
There are no scenarios where a weak increment is invalid on binder_node.
The only possible case where it could be invalid is if the kernel
delivers BR_DECREFS to the process that owns the node, and then
increments the weak refcount again, effectively "reviving" a dead node.
However, that is not possible: when the BR_DECREFS command is delivered,
the kernel removes and frees the binder_node. The fact that you were
able to call binder_inc_node_nilocked() implies that the node is not yet
destroyed, which implies that BR_DECREFS has not been delivered to
userspace, so incrementing the weak refcount is valid.
Note that it's currently possible to trigger this condition if the owner
calls BINDER_THREAD_EXIT while node->has_weak_ref is true. This causes
BC_INCREFS on binder_ref instances to fail when they should not.
Cc: stable@vger.kernel.org
Fixes: 457b9a6f09 ("Staging: android: add binder driver")
Reported-by: Yu-Ting Tseng <yutingtseng@google.com>
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Link: https://patch.msgid.link/20251015-binder-weak-inc-v1-1-7914b092c371@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bbd38fcd2 upstream.
DbC is currently only enabled back if it's in configured state during
suspend.
If system is suspended after DbC is enabled, but before the device is
properly enumerated by the host, then DbC would not be enabled back in
resume.
Always enable DbC back in resume if it's suspended in enabled,
connected, or configured state
Cc: stable <stable@kernel.org>
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37b9dd0d11 upstream.
Drop the check on the maximum transfer length in Raw Gadget for both
control and non-control transfers.
Limiting the transfer length causes a problem with emulating USB devices
whose full configuration descriptor exceeds PAGE_SIZE in length.
Overall, there does not appear to be any reason to enforce any kind of
transfer length limit on the Raw Gadget side for either control or
non-control transfers, so let's just drop the related check.
Cc: stable <stable@kernel.org>
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://patch.msgid.link/a6024e8eab679043e9b8a5defdb41c4bda62f02b.1761085528.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfc2cf4dca upstream.
The list of Huawei LTE modules needing the quirk fixing spurious wakeups
was missing the IDs of the Huawei ME906S module, therefore suspend did not
work.
Cc: stable <stable@kernel.org>
Signed-off-by: Tim Guttzeit <t.guttzeit@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://patch.msgid.link/20251020134304.35079-1-wse@tuxedocomputers.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 706136c572 upstream.
Add a final dma_wmb() barrier before triggering the transmit request
(TCCR_TSRQ) to ensure all descriptor and buffer writes are visible to
the DMA engine.
According to the hardware manual, a read-back operation is required
before writing to the doorbell register to guarantee completion of
previous writes. Instead of performing a dummy read, a dma_wmb() is
used to both enforce the same ordering semantics on the CPU side and
also to ensure completion of writes.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Cc: stable@vger.kernel.org
Co-developed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20251017151830.171062-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
