[ Upstream commit 3a99cbb6fa ]
In case devlink_dpipe_entry_ctx_prepare() failed, release RTNL that was
previously taken and free the memory allocated by
mlxsw_sp_erif_entry_prepare().
Fixes: 2ba5999f00 ("mlxsw: spectrum: Add Support for erif table entries access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36844c855b ]
When reading the number of gearboxes from the hardware, the driver does
not validate the returned 'device type' field. The driver can therefore
wrongly assume that the queried devices are gearboxes.
On Spectrum-3 systems that support different types of devices, this can
prevent the driver from loading, as it will try to query the
temperature sensors from devices which it assumes are gearboxes and in
fact are not.
For example:
[ 218.129230] mlxsw_minimal 2-0048: Reg cmd access status failed (status=7(bad parameter))
[ 218.138282] mlxsw_minimal 2-0048: Reg cmd access failed (reg_id=900a(mtmp),type=write)
[ 218.147131] mlxsw_minimal 2-0048: Failed to setup temp sensor number 256
[ 218.534480] mlxsw_minimal 2-0048: Fail to register core bus
[ 218.540714] mlxsw_minimal: probe of 2-0048 failed with error -5
Fix this by validating the 'device type' field.
Fixes: 2e265a8b6c ("mlxsw: core: Extend hwmon interface with inter-connect temperature attributes")
Fixes: f14f4e621b ("mlxsw: core: Extend thermal core with per inter-connect device thermal zones")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c77e9f0914 ]
Return -EAGAIN instead of -ENETDOWN to provide a slightly milder
information to user space so that an application will know to retry the
syscall when __I40E_CONFIG_BUSY bit is set on pf->state.
Fixes: b3873a5be7 ("net/i40e: Fix concurrency issues between config flow and XSK")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20200205045834.56795-2-maciej.fijalkowski@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12d47f0ea5 ]
Fix a kernel panic by checking that the sta is not NULL.
This could happen during a reconfig flow, as mac80211 moves the sta
between all the states without really checking if the previous state was
successfully set. So, if for some reason we failed to add back the
station, subsequent calls to sta_state() callback will be done when the
station is NULL. This would result in a following panic:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000040
IP: iwl_mvm_cfg_he_sta+0xfc/0x690 [iwlmvm]
[..]
Call Trace:
iwl_mvm_mac_sta_state+0x629/0x6f0 [iwlmvm]
drv_sta_state+0xf4/0x950 [mac80211]
ieee80211_reconfig+0xa12/0x2180 [mac80211]
ieee80211_restart_work+0xbb/0xe0 [mac80211]
process_one_work+0x1e2/0x610
worker_thread+0x4d/0x3e0
[..]
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baa6cf8450 ]
Use a unique name when registering a thermal zone. Otherwise, with
multiple NICS, we hit the following warning during the unregistration.
WARNING: CPU: 2 PID: 3525 at fs/sysfs/group.c:255
RIP: 0010:sysfs_remove_group+0x80/0x90
Call Trace:
dpm_sysfs_remove+0x57/0x60
device_del+0x5a/0x350
? sscanf+0x4e/0x70
device_unregister+0x1a/0x60
hwmon_device_unregister+0x4a/0xa0
thermal_remove_hwmon_sysfs+0x175/0x1d0
thermal_zone_device_unregister+0x188/0x1e0
iwl_mvm_thermal_exit+0xe7/0x100 [iwlmvm]
iwl_op_mode_mvm_stop+0x27/0x180 [iwlmvm]
_iwl_op_mode_stop.isra.3+0x2b/0x50 [iwlwifi]
iwl_opmode_deregister+0x90/0xa0 [iwlwifi]
__exit_compat+0x10/0x2c7 [iwlmvm]
__x64_sys_delete_module+0x13f/0x270
do_syscall_64+0x5a/0x110
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2f9a4e4a5 ]
The loop counter addr is a u16 where as the upper limit of the loop
is an int. In the unlikely event that the il->cfg->eeprom_size is
greater than 64K then we end up with an infinite loop since addr will
wrap around an never reach upper loop limit. Fix this by making addr
an int.
Addresses-Coverity: ("Infinite loop")
Fixes: be663ab670 ("iwlwifi: split the drivers for agn and legacy devices 3945/4965")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4f84ff837 ]
Sometimes the TX queue may be empty and we could possible
dequeue a NULL pointer, crash the kernel. If the skb is NULL
then there is nothing to do, just leave the ISR.
And the TX queue should not be empty here, so print an error
to see if there is anything wrong for DMA ring.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b61156fba7 ]
Clang warns:
../drivers/net/wireless/intersil/hostap/hostap_ap.c:2511:3: warning:
misleading indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
if (sta->tx_supp_rates & WLAN_RATE_5M5)
^
../drivers/net/wireless/intersil/hostap/hostap_ap.c:2509:2: note:
previous statement is here
if (sta->tx_supp_rates & WLAN_RATE_2M)
^
1 warning generated.
This warning occurs because there is a space before the tab on this
line. Remove it so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
Fixes: ff1d2767d5 ("Add HostAP wireless driver.")
Link: https://github.com/ClangBuiltLinux/linux/issues/813
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca9c74ae9b ]
Use "%zu" for size_t. Seen on ARM allmodconfig:
drivers/net/ethernet/mellanox/mlx5/core/wq.c: In function 'mlx5_wq_cyc_wqe_dump':
include/linux/kern_levels.h:5:18: warning: format '%ld' expects argument of type 'long int', but argument 5 has type 'size_t' {aka 'unsigned int'} [-Wformat=]
Fixes: 130c7b46c9 ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90f29f0ead ]
It is not an error to unplug a cable from the ENETC port even with TSN
offloads, so don't spam the log with link-related messages from the
tc-taprio offload subsystem, a single notification is sufficient:
[10972.351859] fsl_enetc 0000:00:00.0 eno0: Qbv PSPEED set speed link down.
[10972.360241] fsl_enetc 0000:00:00.0 eno0: Link is Down
Fixes: 2e47cb415f ("enetc: update TSN Qbv PSPEED set according to adjust link speed")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3071c51783 ]
When running in XDP mode, pages come from the page pool, and should
be freed back to the same pool or specifically detached. Currently,
when the driver re-initializes, the page pool destruction is delayed
forever since it thinks there are oustanding pages.
Fixes: 322b87ca55 ("bnxt_en: add page_pool support")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42ae1a5c76 ]
In some configurations, gcc tries too hard to optimize this code:
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c: In function 'mlx5e_grp_sw_update_stats':
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c:302:1: error: the frame size of 1336 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
As was stated in the bug report, the reason is that gcc runs into a corner
case in the register allocator that is rather hard to fix in a good way.
As there is an easy way to work around it, just add a comment and the
barrier that stops gcc from trying to overoptimize the function.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=92657
Cc: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d266f19f3a ]
If we fail to locate GPIO for any reason other than deferral or
not-found-GPIO, we try to print device tree node info, however if might
be freed already as we called of_node_put() on it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f45ebe0d8 ]
In the case where the hardware gives us a null Rx descriptor, it is
theoretically possible that we could call one of our skb-construction
functions with no data pointer, which would cause a panic.
In real life, this will never happen - we only get null RX
descriptors as the final descriptor in a chain of otherwise-valid
descriptors. When this happens, the skb will be extant and we'll just
call ice_add_rx_frag(), which can deal with empty data buffers.
Unfortunately, Coverity does not have intimate knowledge of our
hardware, so we must add a check here.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aec743d69 ]
RGMII requires a delay of 2ns between the data and the clock signal.
There are at least three ways this can happen. One possibility is by
having the PHY generate this delay.
This is a common source for problems (for example with slow TX speeds or
packet loss when sending data). The TX delay configuration of the
RTL8211F PHY can be set either by pin-strappping the RXD1 pin (HIGH
means enabled, LOW means disabled) or through configuring a paged
register. The setting from the RXD1 pin is also reflected in the
register.
Add debug logging to the TX delay configuration on RTL8211F so it's
easier to spot these issues (for example if the TX delay is enabled for
both, the RTL8211F PHY and the MAC).
This is especially helpful because there is no public datasheet for the
RTL8211F PHY available with all the RX/TX delay specifics.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c705f9fc6a ]
In ezusb_init, if upriv is NULL, the code crashes. However, the caller
in ezusb_probe can handle the error and print the failure message.
The patch replaces the BUG_ON call to error return.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f325937735 ]
Some users complained about problems with r8169 and it turned out that
the generic PHY driver was used instead instead of the dedicated one.
In all cases reason was that r8169.ko was in initramfs, but realtek.ko
not. Manually adding realtek.ko to initramfs fixed the issues.
Root cause seems to be that tools like dracut and genkernel don't
consider softdeps. Add a check for loaded Realtek PHY driver module
and provide the user with a hint if it's not loaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d1997db87 ]
This reverts commit 78beef629f ("nfp: abm: fix memory leak in
nfp_abm_u32_knode_replace").
The quoted commit does not fix anything and resulted in a bogus
CVE-2019-19076.
If match is NULL then it is known there is no matching entry in
list, hence, calling nfp_abm_u32_knode_delete() is pointless.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6525b5ef65 ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable]
Fixes: c431047c4e ("enetc: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 148587a59f ]
Qiang Zhao points out that these offsets get written to 16-bit
registers, and there are some QE platforms with more than 64K
muram. So it is possible that qe_muram_alloc() gives us an allocation
that can't actually be used by the hardware, so detect and reject
that.
Reported-by: Qiang Zhao <qiang.zhao@nxp.com>
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e01cc82c4d ]
the tlv len is set to the total len of the wmi cmd, it will trigger
firmware crash, correct the tlv len.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1 and QCA6174
PCIE with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Fixes: ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c8e60fb86 ]
Commit 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling
brcmf_bus_started()") changed the initialization order of the brcmfmac
SDIO driver. Unfortunately since brcmf_sdiod_intr_register() is now
called before the sdiodev->bus_if initialization, it reads the wrong
chip ID and fails to initialize the GPIO on brcm43362. Thus the chip
cannot send interrupts and fails to probe:
[ 12.517023] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
[ 12.531214] ieee80211 phy0: brcmf_bus_started: failed: -110
[ 12.536976] ieee80211 phy0: brcmf_attach: dongle is not responding: err=-110
[ 12.566467] brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
Initialize the bus interface earlier to ensure that
brcmf_sdiod_intr_register() properly sets up the OOB interrupt.
BugLink: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908438
Fixes: 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling brcmf_bus_started()")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a68fa5f9 ]
The rate mask is used to tell firmware the supported rate depends on
negotiation. We loop 2 times for all VHT/HT 2SS rate mask first, and then
only keep the part according to chip's NSS.
This commit fixes the logic error of '&' operations for VHT/HT rate, and
we should run this logic before adding legacy rate.
To access HT MCS map, index 0/1 represent MCS 0-7/8-15 respectively. Use
NL80211_BAND_xxx is incorrect, so fix it as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ba8b3b6bd ]
The management packets, send to firmware via WMI, are
mapped using the direction DMA_TO_DEVICE. Currently in
case of wmi cleanup, these buffers are being unmapped
using an incorrect DMA direction. This can cause unwanted
behavior when the host driver is handling a restart
of the wlan firmware.
We might see a trace like below
[<ffffff8008098b18>] __dma_inv_area+0x28/0x58
[<ffffff8001176734>] ath10k_wmi_mgmt_tx_clean_up_pending+0x60/0xb0 [ath10k_core]
[<ffffff80088c7c50>] idr_for_each+0x78/0xe4
[<ffffff80011766a4>] ath10k_wmi_detach+0x4c/0x7c [ath10k_core]
[<ffffff8001163d7c>] ath10k_core_stop+0x58/0x68 [ath10k_core]
[<ffffff800114fb74>] ath10k_halt+0xec/0x13c [ath10k_core]
[<ffffff8001165110>] ath10k_core_restart+0x11c/0x1a8 [ath10k_core]
[<ffffff80080c36bc>] process_one_work+0x16c/0x31c
Fix the incorrect DMA direction during the wmi
management tx buffer cleanup.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: dc405152bb ("ath10k: handle mgmt tx completion event")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 953c4a08df ]
o call skb_reset_network_header() before hdlc->xmit()
o change skb proto to HDLC (0x0019) before hdlc->xmit()
o call dev_queue_xmit_nit() before hdlc->xmit()
This changes make it possible to trace (tcpdump) outgoing layer2
(ETH_P_HDLC) packets
Additionally call skb_reset_network_header() after each skb_push() /
skb_pull().
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c83db9ef56 ]
The IXP4xx driver was initializing the MDIO bus before even
probing, in the callbacks supposed to be used for setting up
the module itself, and with the side effect of trying to
register the MDIO bus as soon as this module was loaded or
compiled into the kernel whether the device was discovered
or not.
This does not work with multiplatform environments.
To get rid of this: set up the MDIO bus from the probe()
callback and remove it in the remove() callback. Rename
the probe() and remove() calls to reflect the most common
conventions.
Since there is a bit of checking for the ethernet feature
to be present in the MDIO registering function, making the
whole module not even be registered if we can't find an
MDIO bus, we need something similar: register the MDIO
bus when the corresponding ethernet is probed, and
return -EPROBE_DEFER on the other interfaces until this
happens. If no MDIO bus is present on any of the
registered interfaces we will eventually bail out.
None of the platforms I've seen has e.g. MDIO on EthB
and only uses EthC, there is always a Ethernet hardware
on the NPE (B, C) that has the MDIO bus, we just might
have to wait for it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c26a2c2ddc ]
The driver wrongly assumes that it is the only entity that can set the
SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the
gfar_clean_tx_ring function, where the TX timestamp is collected if
necessary, the aforementioned bit is used to discriminate whether or not
the TX timestamp should be delivered to the socket's error queue.
But a stacked driver such as a DSA switch can also set the
SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in
order to denote that the hardware timestamping process is undergoing.
Therefore, gianfar would misinterpret the "in progress" bit as being its
own, and deliver a second skb clone in the socket's error queue,
completely throwing off a PTP process which is not expecting to receive
it, _even though_ TX timestamping is not enabled for gianfar.
There have been discussions [0] as to whether non-MAC drivers need or
not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2
timestamps, a sw and a hw one, to applications which only expect one).
But as of this patch, there are at least 2 PTP drivers that would break
in conjunction with gianfar: the sja1105 DSA switch and the felix
switch, by way of its ocelot core driver.
So regardless of that conclusion, fix the gianfar driver to not do stuff
based on flags set by others and not intended for it.
[0]: https://www.spinics.net/lists/netdev/msg619699.html
Fixes: f0ee7acfcd ("gianfar: Add hardware TX timestamping support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 216b44000a ]
The brcmu_pkt_buf_free_skb() function frees "pkt" so it leads to a
static checker warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1974 brcmf_sdio_readframes()
error: dereferencing freed memory 'pkt'
It looks like there was supposed to be a continue after we free "pkt".
Fixes: 4754fceeb9 ("brcmfmac: streamline SDIO read frame routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cc509aa83 ]
In the implementation of brcmf_p2p_create_p2pdev() the allocated memory
for p2p_vif is leaked when the mac address is the same as primary
interface. To fix this, go to error path to release p2p_vif via
brcmf_free_vif().
Fixes: cb746e4783 ("brcmfmac: check p2pdev mac address uniqueness")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b1413f00b ]
There is a check on the retry counter invalid_buf_id_retry that is always
false because invalid_buf_id_retry is initialized to zero on each iteration
of a while-loop. Fix this by initializing the retry counter before the
while-loop starts.
Addresses-Coverity: ("Logically dead code")
Fixes: b4a967b7d0 ("wil6210: reset buff id in status message after completion")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8a595a87e ]
When ath10k_qmi_init() fails, the error handling does not free the irq
resources, which causes an issue if we EPROBE_DEFER as we'll attempt to
(re-)register irqs which are already registered.
Fix this by doing a power off since we just powered on the hardware, and
freeing the irqs as error handling.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f90522591 ]
Recent months, our customer reported several kernel crashes all
preceding with following message:
NETDEV WATCHDOG: eth2 (enic): transmit queue 0 timed out
Error message of one of those crashes:
BUG: unable to handle kernel paging request at ffffffffa007e090
After analyzing severl vmcores, I found that most of crashes are
caused by memory corruption. And all the corrupted memory areas
are overwritten by data of network packets. Moreover, I also found
that the tx queues were enabled over watchdog reset.
After going through the source code, I found that in enic_stop(),
the tx queues stopped by netif_tx_disable() could be woken up over
a small time window between netif_tx_disable() and the
napi_disable() by the following code path:
napi_poll->
enic_poll_msix_wq->
vnic_cq_service->
enic_wq_service->
netif_wake_subqueue(enic->netdev, q_number)->
test_and_clear_bit(__QUEUE_STATE_DRV_XOFF, &txq->state)
In turn, upper netowrk stack could queue skb to ENIC NIC though
enic_hard_start_xmit(). And this might introduce some race condition.
Our customer comfirmed that this kind of kernel crash doesn't occur over
90 days since they applied this patch.
Signed-off-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1754c4f60a ]
Commit e5e884b426 ("libertas: Fix two buffer overflows at parsing bss
descriptor") introduced a bounds check on the number of supplied rates to
lbs_ibss_join_existing() and made it to return on overflow.
However, the aforementioned commit doesn't set the return value accordingly
and thus, lbs_ibss_join_existing() would return with zero even though it
failed.
Make lbs_ibss_join_existing return -EINVAL in case the bounds check on the
number of supplied rates fails.
Fixes: e5e884b426 ("libertas: Fix two buffer overflows at parsing bss descriptor")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7bf1fb7dd ]
Commit e5e884b426 ("libertas: Fix two buffer overflows at parsing bss
descriptor") introduced a bounds check on the number of supplied rates to
lbs_ibss_join_existing().
Unfortunately, it introduced a return path from within a RCU read side
critical section without a corresponding rcu_read_unlock(). Fix this.
Fixes: e5e884b426 ("libertas: Fix two buffer overflows at parsing bss descriptor")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b70261a288 ]
mwifiex_cmd_append_vsie_tlv() calls memcpy() without checking
the destination size may trigger a buffer overflower,
which a local user could use to cause denial of service
or the execution of arbitrary code.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Qing Xu <m1s5p6688@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a9b153c55 ]
mwifiex_ret_wmm_get_status() calls memcpy() without checking the
destination size.Since the source is given from remote AP which
contains illegal wmm elements , this may trigger a heap buffer
overflow.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Qing Xu <m1s5p6688@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8526ad9646 upstream.
nsim_dev_take_snapshot_write() uses nsim_dev and nsim_dev->dummy_region.
So, during this function, these data shouldn't be removed.
But there is no protecting stuff in this function.
There are two similar cases.
1. reload case
reload could be called during nsim_dev_take_snapshot_write().
When reload is being executed, nsim_dev_reload_down() is called and it
calls nsim_dev_reload_destroy(). nsim_dev_reload_destroy() calls
devlink_region_destroy() to destroy nsim_dev->dummy_region.
So, during nsim_dev_take_snapshot_write(), nsim_dev->dummy_region()
would be removed.
At this point, snapshot_write() would access freed pointer.
In order to fix this case, take_snapshot file will be removed before
devlink_region_destroy().
The take_snapshot file will be re-created by ->reload_up().
2. del_device_store case
del_device_store() also could call nsim_dev_reload_destroy()
during nsim_dev_take_snapshot_write(). If so, panic would occur.
This problem is actually the same problem with the first case.
So, this problem will be fixed by the first case's solution.
Test commands:
modprobe netdevsim
while :
do
echo 1 > /sys/bus/netdevsim/new_device &
echo 1 > /sys/bus/netdevsim/del_device &
devlink dev reload netdevsim/netdevsim1 &
echo 1 > /sys/kernel/debug/netdevsim/netdevsim1/take_snapshot &
done
Splat looks like:
[ 45.564513][ T975] general protection fault, probably for non-canonical address 0xdffffc000000003a: 0000 [#1] SMP DEI
[ 45.566131][ T975] KASAN: null-ptr-deref in range [0x00000000000001d0-0x00000000000001d7]
[ 45.566135][ T975] CPU: 1 PID: 975 Comm: bash Not tainted 5.5.0+ #322
[ 45.569020][ T975] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 45.569026][ T975] RIP: 0010:__mutex_lock+0x10a/0x14b0
[ 45.570518][ T975] Code: 08 84 d2 0f 85 7f 12 00 00 44 8b 0d 10 23 65 02 45 85 c9 75 29 49 8d 7f 68 48 b8 00 00 00 0f
[ 45.570522][ T975] RSP: 0018:ffff888046ccfbf0 EFLAGS: 00010206
[ 45.572305][ T975] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 45.572308][ T975] RDX: 000000000000003a RSI: ffffffffac926440 RDI: 00000000000001d0
[ 45.576843][ T975] RBP: ffff888046ccfd70 R08: ffffffffab610645 R09: 0000000000000000
[ 45.576847][ T975] R10: ffff888046ccfd90 R11: ffffed100d6360ad R12: 0000000000000000
[ 45.578471][ T975] R13: dffffc0000000000 R14: ffffffffae1976c0 R15: 0000000000000168
[ 45.578475][ T975] FS: 00007f614d6e7740(0000) GS:ffff88806c400000(0000) knlGS:0000000000000000
[ 45.581492][ T975] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 45.582942][ T975] CR2: 00005618677d1cf0 CR3: 000000005fb9c002 CR4: 00000000000606e0
[ 45.584543][ T975] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 45.586633][ T975] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 45.589889][ T975] Call Trace:
[ 45.591445][ T975] ? devlink_region_snapshot_create+0x55/0x4a0
[ 45.601250][ T975] ? mutex_lock_io_nested+0x1380/0x1380
[ 45.602817][ T975] ? mutex_lock_io_nested+0x1380/0x1380
[ 45.603875][ T975] ? mark_held_locks+0xa5/0xe0
[ 45.604769][ T975] ? _raw_spin_unlock_irqrestore+0x2d/0x50
[ 45.606147][ T975] ? __mutex_unlock_slowpath+0xd0/0x670
[ 45.607723][ T975] ? crng_backtrack_protect+0x80/0x80
[ 45.613530][ T975] ? wait_for_completion+0x390/0x390
[ 45.615152][ T975] ? devlink_region_snapshot_create+0x55/0x4a0
[ 45.616834][ T975] devlink_region_snapshot_create+0x55/0x4a0
[ ... ]
Fixes: 4418f862d6 ("netdevsim: implement support for devlink region and snapshots")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5b878e36c upstream.
I changed the API for asking for a session protection but
I omitted the TDLS flows. Fix that now.
Note that for the TDLS flow, we need to block until the
session protection actually starts, so add this option
to iwl_mvm_schedule_session_protection.
This patch fixes a firmware assert in the TDLS flow since
the old TIME_EVENT_CMD is not supported anymore by newer
firwmare versions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: fe959c7b20 ("iwlwifi: mvm: use the new session protection command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc4255eff5 upstream.
When a FTM request is aborted, the driver sends the abort command to
the fw and waits for a response. When the response arrives, the driver
calls cfg80211_pmsr_complete() for that request.
However, cfg80211 frees the requested data immediately after sending
the abort command, so this may lead to use after free.
Fix it by clearing the request data in the driver when the abort
command arrives and ignoring the fw notification that will come
afterwards.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Fixes: fc36ffda32 ("iwlwifi: mvm: support FTM initiator")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d239380196 upstream.
ath10k_pci_dump_memory_reg() will try to access memory of type
ATH10K_MEM_REGION_TYPE_IOREG however, if a hardware restart is in progress
this can crash a system.
Individual ioread32() time has been observed to jump from 15-20 ticks to >
80k ticks followed by a secure-watchdog bite and a system reset.
Work around this corner case by only issuing the read transaction when the
driver state is ATH10K_STATE_ON.
Tested-on: QCA9988 PCI 10.4-3.9.0.2-00044
Fixes: 219cc084c6 ("ath10k: add memory dump support QCA9984")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b57e66ad42 ]
For a cyclic work queue, when not requesting a completion per WQE,
a single CQE might indicate the completion of several WQEs.
However, in case some WQE in the batch causes an error, then an error
completion is issued, breaking the batch, and pointing to the offending
WQE in the wqe_counter field.
Hence, WQE-specific error CQE handling (like printing, breaking, etc...)
should be performed only for the last WQE in batch.
Fixes: 130c7b46c9 ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Fixes: fd9b4be800 ("net/mlx5e: RX, Support multiple outstanding UMR posts")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
