[ Upstream commit 3a99cbb6fa ]
In case devlink_dpipe_entry_ctx_prepare() failed, release RTNL that was
previously taken and free the memory allocated by
mlxsw_sp_erif_entry_prepare().
Fixes: 2ba5999f00 ("mlxsw: spectrum: Add Support for erif table entries access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36844c855b ]
When reading the number of gearboxes from the hardware, the driver does
not validate the returned 'device type' field. The driver can therefore
wrongly assume that the queried devices are gearboxes.
On Spectrum-3 systems that support different types of devices, this can
prevent the driver from loading, as it will try to query the
temperature sensors from devices which it assumes are gearboxes and in
fact are not.
For example:
[ 218.129230] mlxsw_minimal 2-0048: Reg cmd access status failed (status=7(bad parameter))
[ 218.138282] mlxsw_minimal 2-0048: Reg cmd access failed (reg_id=900a(mtmp),type=write)
[ 218.147131] mlxsw_minimal 2-0048: Failed to setup temp sensor number 256
[ 218.534480] mlxsw_minimal 2-0048: Fail to register core bus
[ 218.540714] mlxsw_minimal: probe of 2-0048 failed with error -5
Fix this by validating the 'device type' field.
Fixes: 2e265a8b6c ("mlxsw: core: Extend hwmon interface with inter-connect temperature attributes")
Fixes: f14f4e621b ("mlxsw: core: Extend thermal core with per inter-connect device thermal zones")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c77e9f0914 ]
Return -EAGAIN instead of -ENETDOWN to provide a slightly milder
information to user space so that an application will know to retry the
syscall when __I40E_CONFIG_BUSY bit is set on pf->state.
Fixes: b3873a5be7 ("net/i40e: Fix concurrency issues between config flow and XSK")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20200205045834.56795-2-maciej.fijalkowski@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca9c74ae9b ]
Use "%zu" for size_t. Seen on ARM allmodconfig:
drivers/net/ethernet/mellanox/mlx5/core/wq.c: In function 'mlx5_wq_cyc_wqe_dump':
include/linux/kern_levels.h:5:18: warning: format '%ld' expects argument of type 'long int', but argument 5 has type 'size_t' {aka 'unsigned int'} [-Wformat=]
Fixes: 130c7b46c9 ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90f29f0ead ]
It is not an error to unplug a cable from the ENETC port even with TSN
offloads, so don't spam the log with link-related messages from the
tc-taprio offload subsystem, a single notification is sufficient:
[10972.351859] fsl_enetc 0000:00:00.0 eno0: Qbv PSPEED set speed link down.
[10972.360241] fsl_enetc 0000:00:00.0 eno0: Link is Down
Fixes: 2e47cb415f ("enetc: update TSN Qbv PSPEED set according to adjust link speed")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3071c51783 ]
When running in XDP mode, pages come from the page pool, and should
be freed back to the same pool or specifically detached. Currently,
when the driver re-initializes, the page pool destruction is delayed
forever since it thinks there are oustanding pages.
Fixes: 322b87ca55 ("bnxt_en: add page_pool support")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42ae1a5c76 ]
In some configurations, gcc tries too hard to optimize this code:
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c: In function 'mlx5e_grp_sw_update_stats':
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c:302:1: error: the frame size of 1336 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
As was stated in the bug report, the reason is that gcc runs into a corner
case in the register allocator that is rather hard to fix in a good way.
As there is an easy way to work around it, just add a comment and the
barrier that stops gcc from trying to overoptimize the function.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=92657
Cc: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f45ebe0d8 ]
In the case where the hardware gives us a null Rx descriptor, it is
theoretically possible that we could call one of our skb-construction
functions with no data pointer, which would cause a panic.
In real life, this will never happen - we only get null RX
descriptors as the final descriptor in a chain of otherwise-valid
descriptors. When this happens, the skb will be extant and we'll just
call ice_add_rx_frag(), which can deal with empty data buffers.
Unfortunately, Coverity does not have intimate knowledge of our
hardware, so we must add a check here.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f325937735 ]
Some users complained about problems with r8169 and it turned out that
the generic PHY driver was used instead instead of the dedicated one.
In all cases reason was that r8169.ko was in initramfs, but realtek.ko
not. Manually adding realtek.ko to initramfs fixed the issues.
Root cause seems to be that tools like dracut and genkernel don't
consider softdeps. Add a check for loaded Realtek PHY driver module
and provide the user with a hint if it's not loaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d1997db87 ]
This reverts commit 78beef629f ("nfp: abm: fix memory leak in
nfp_abm_u32_knode_replace").
The quoted commit does not fix anything and resulted in a bogus
CVE-2019-19076.
If match is NULL then it is known there is no matching entry in
list, hence, calling nfp_abm_u32_knode_delete() is pointless.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6525b5ef65 ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable]
Fixes: c431047c4e ("enetc: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c83db9ef56 ]
The IXP4xx driver was initializing the MDIO bus before even
probing, in the callbacks supposed to be used for setting up
the module itself, and with the side effect of trying to
register the MDIO bus as soon as this module was loaded or
compiled into the kernel whether the device was discovered
or not.
This does not work with multiplatform environments.
To get rid of this: set up the MDIO bus from the probe()
callback and remove it in the remove() callback. Rename
the probe() and remove() calls to reflect the most common
conventions.
Since there is a bit of checking for the ethernet feature
to be present in the MDIO registering function, making the
whole module not even be registered if we can't find an
MDIO bus, we need something similar: register the MDIO
bus when the corresponding ethernet is probed, and
return -EPROBE_DEFER on the other interfaces until this
happens. If no MDIO bus is present on any of the
registered interfaces we will eventually bail out.
None of the platforms I've seen has e.g. MDIO on EthB
and only uses EthC, there is always a Ethernet hardware
on the NPE (B, C) that has the MDIO bus, we just might
have to wait for it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c26a2c2ddc ]
The driver wrongly assumes that it is the only entity that can set the
SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the
gfar_clean_tx_ring function, where the TX timestamp is collected if
necessary, the aforementioned bit is used to discriminate whether or not
the TX timestamp should be delivered to the socket's error queue.
But a stacked driver such as a DSA switch can also set the
SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in
order to denote that the hardware timestamping process is undergoing.
Therefore, gianfar would misinterpret the "in progress" bit as being its
own, and deliver a second skb clone in the socket's error queue,
completely throwing off a PTP process which is not expecting to receive
it, _even though_ TX timestamping is not enabled for gianfar.
There have been discussions [0] as to whether non-MAC drivers need or
not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2
timestamps, a sw and a hw one, to applications which only expect one).
But as of this patch, there are at least 2 PTP drivers that would break
in conjunction with gianfar: the sja1105 DSA switch and the felix
switch, by way of its ocelot core driver.
So regardless of that conclusion, fix the gianfar driver to not do stuff
based on flags set by others and not intended for it.
[0]: https://www.spinics.net/lists/netdev/msg619699.html
Fixes: f0ee7acfcd ("gianfar: Add hardware TX timestamping support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f90522591 ]
Recent months, our customer reported several kernel crashes all
preceding with following message:
NETDEV WATCHDOG: eth2 (enic): transmit queue 0 timed out
Error message of one of those crashes:
BUG: unable to handle kernel paging request at ffffffffa007e090
After analyzing severl vmcores, I found that most of crashes are
caused by memory corruption. And all the corrupted memory areas
are overwritten by data of network packets. Moreover, I also found
that the tx queues were enabled over watchdog reset.
After going through the source code, I found that in enic_stop(),
the tx queues stopped by netif_tx_disable() could be woken up over
a small time window between netif_tx_disable() and the
napi_disable() by the following code path:
napi_poll->
enic_poll_msix_wq->
vnic_cq_service->
enic_wq_service->
netif_wake_subqueue(enic->netdev, q_number)->
test_and_clear_bit(__QUEUE_STATE_DRV_XOFF, &txq->state)
In turn, upper netowrk stack could queue skb to ENIC NIC though
enic_hard_start_xmit(). And this might introduce some race condition.
Our customer comfirmed that this kind of kernel crash doesn't occur over
90 days since they applied this patch.
Signed-off-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b57e66ad42 ]
For a cyclic work queue, when not requesting a completion per WQE,
a single CQE might indicate the completion of several WQEs.
However, in case some WQE in the batch causes an error, then an error
completion is issued, breaking the batch, and pointing to the offending
WQE in the wqe_counter field.
Hence, WQE-specific error CQE handling (like printing, breaking, etc...)
should be performed only for the last WQE in batch.
Fixes: 130c7b46c9 ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Fixes: fd9b4be800 ("net/mlx5e: RX, Support multiple outstanding UMR posts")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21b5f672fb ]
It turned out that on low performance systems the original change can
cause lower tx performance. On a N3450-based mini-PC tx performance
in iperf3 was reduced from 950Mbps to ~900Mbps. Therefore effectively
revert the original change, just use pcie_set_readrq() now instead of
changing the PCIe capability register directly.
Fixes: 2df49d3654 ("r8169: remove fiddling with the PCIe max read request size")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61c00cca41 ]
Deprecate the generic TLS cap bit, use the new TX-specific
TLS cap bit instead.
Fixes: a12ff35e0f ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0202d293c2 ]
commit cedeac9df4 ("qed: Add support for Timestamping the unicast
PTP packets.") handles the timestamping of L4 ptp packets only.
This patch adds driver changes to detect/timestamp both L2/L4 unicast
PTP packets.
Fixes: cedeac9df4 ("qed: Add support for Timestamping the unicast PTP packets.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 909c1dde67 ]
The recent patch to support passive mode converter did not take care the
phy interface configuration in PCI platform data. Hence, converting all
the PCI platform data from plat->interface to plat->phy_interface as the
default mode is meant for PHY.
Fixes: 0060c87833 ("net: stmmac: implement support for passive mode converters via dt")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f633d5820 ]
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 0efedbf11f ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ba31cd937 ]
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Verma, Aashish <aashishx.verma@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 907a076881 ]
We should always do a read of current value of XGMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: 3cd1cfcba2 ("net: stmmac: Implement VLAN Hash Filtering in XGMAC")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9eeeb3c9de ]
It should always do a read of current value of GMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: c1be0022df ("net: stmmac: Add VLAN HASH filtering support in GMAC4+")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f822e9c4ff ]
GEM_MAX_TX_LEN currently resolves to 0x3FF8 for any IP version supporting
TSO with full 14bits of length field in payload descriptor. But an IP
errata causes false amba_error (bit 6 of ISR) when length in payload
descriptors is specified above 16387. The error occurs because the DMA
falsely concludes that there is not enough space in SRAM for incoming
payload. These errors were observed continuously under stress of large
packets using iperf on a version where SRAM was 16K for each queue. This
errata will be documented shortly and affects all versions since TSO
functionality was added. Hence limit the max length to 0x3FC0 (rounded).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 41c1ef978c ]
The IP TSO implementation does NOT require the length to be a
multiple of 8. That is only a requirement for UFO as per IP
documentation. Hence, exit macb_features_check function in the
beginning if the protocol is not UDP. Only when it is UDP,
proceed further to the alignment checks. Update comments to
reflect the same. Also remove dead code checking for protocol
TCP when calculating header length.
Fixes: 1629dd4f76 ("cadence: Add LSO support.")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 08db2cf577 ]
SA context is allocated at mlx5_fpga_ipsec_create_sa_ctx,
however the counterpart mlx5_fpga_ipsec_delete_sa_ctx function
nullifies sa_ctx pointer without freeing the memory allocated,
hence the memory leak.
Fix by free SA context when the SA is released.
Fixes: d6c4f0298c ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0dc2c534f1 ]
The function mlx5_fpga_esp_validate_xfrm_attrs is wrongly used
with negative negation as zero value indicates success but it
used as failure return value instead.
Fix by remove the unary not negation operator.
Fixes: 05564d0ae0 ("net/mlx5: Add flow-steering commands for FPGA IPSec implementation")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 263a425a48 ]
After a number of suspend and resume cycles, it is possible for the RBUF
to be stuck in Wake-on-LAN mode, despite the MPD enable bit being
cleared which instructed the RBUF to exit that mode.
Avoid creating that problematic condition by clearing the RX_EN and
TX_EN bits in the UniMAC prior to disable the Magic Packet Detector
logic which is guaranteed to make the RBUF exit Wake-on-LAN mode.
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7d10f0774f ]
It forgot to reduce the value of the variable retry in a while loop
in the ethqos_configure() function. It may cause an endless loop and
without timeout.
Fixes: a7c30e62d4 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c35947b8ff ]
Move rx_dropped and rx_errors counters in mvneta_pcpu_stats in order to
avoid possible races updating statistics
Fixes: 562e2f467e ("net: mvneta: Improve the buffer allocation method for SWBM")
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73a21fa817 ]
Stop removing modes that are not supported on the system interface
when the connected PHY is capable of rate adaptation. This addresses
an issue with the LS1046ARDB board 10G interface no longer working
with an 1G link partner after autonegotiation support was added
for the Aquantia PHY on board in
commit 09c4c57f7b ("net: phy: aquantia: add support for auto-negotiation configuration")
Before this commit the values advertised by the PHY were not
influenced by the dpaa_eth driver removal of system-side unsupported
modes as the aqr_config_aneg() was basically a no-op. After this
commit, the modes removed by the dpaa_eth driver were no longer
advertised thus autonegotiation with 1G link partners failed.
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe06bf3d83 upstream.
Clang warns:
../drivers/net/ethernet/dec/tulip/uli526x.c:1812:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
switch (mode) {
^
../drivers/net/ethernet/dec/tulip/uli526x.c:1809:2: note: previous
statement is here
if (cr6set)
^
1 warning generated.
../drivers/net/ethernet/dec/tulip/dmfe.c:2217:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
switch(mode) {
^
../drivers/net/ethernet/dec/tulip/dmfe.c:2214:2: note: previous
statement is here
if (cr6set)
^
1 warning generated.
This warning occurs because there is a space before the tab on these
lines. Remove them so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
While we are here, adjust the default block in dmfe_init_module to have
a proper break between the label and assignment and add a space between
the switch and opening parentheses to avoid a checkpatch warning.
Fixes: e1c3e50140 ("[PATCH] initialisation cleanup for ULI526x-net-driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/795
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c61e22300 upstream.
Clang warns:
../drivers/net/ethernet/smsc/smc911x.c:939:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
if (!lp->ctl_rfduplx)
^
../drivers/net/ethernet/smsc/smc911x.c:936:2: note: previous statement
is here
if (lp->ctl_rspeed != 100)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 0a0c72c911 ("[PATCH] RE: [PATCH 1/1] net driver: Add support for SMSC LAN911x line of ethernet chips")
Link: https://github.com/ClangBuiltLinux/linux/issues/796
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d407302895 ]
The current logic that calls pci_disable_device() in __bnxt_close_nic()
during firmware reset is flawed. If firmware is still alive, we're
disabling the device too early, causing some firmware commands to
not reach the firmware.
Fix it by moving the logic to bnxt_reset_close(). If firmware is
in fatal condition, we call pci_disable_device() before we free
any of the rings to prevent DMA corruption of the freed rings. If
firmware is still alive, we call pci_disable_device() after the
last firmware message has been sent.
Fixes: 3bc7d4a352 ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5ce31b5e1 ]
Be sure to include all the packet type bits in the mask.
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 12de2eadf8 ]
bnxt_ulp_start() needs to be called before SRIOV is re-enabled after
firmware reset. Re-enabling SRIOV may consume all the resources and
may cause the RDMA driver to fail to get MSIX and other resources.
Fix it by calling bnxt_ulp_start() first before calling
bnxt_reenable_sriov().
We re-arrange the logic so that we call bnxt_ulp_start() and
bnxt_reenable_sriov() in proper sequence in bnxt_fw_reset_task() and
bnxt_open(). The former is the normal coordinated firmware reset sequence
and the latter is firmware reset while the function is down. This new
logic is now more straight forward and will now fix both scenarios.
Fixes: f3a6d206c2 ("bnxt_en: Call bnxt_ulp_stop()/bnxt_ulp_start() during error recovery.")
Reported-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c16d4ee0e3 ]
Put the current logic in bnxt_open() to re-enable SRIOV after detecting
firmware reset into a new function bnxt_reenable_sriov(). This call
needs to be invoked in the firmware reset path also in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 14b41a2959 ]
When running v5.5 with a rootfs on NFS, memory abort may happen in
the system resume stage:
Unable to handle kernel paging request at virtual address dead00000000012a
[dead00000000012a] address between user and kernel address ranges
pc : run_timer_softirq+0x334/0x3d8
lr : run_timer_softirq+0x244/0x3d8
x1 : ffff800011cafe80 x0 : dead000000000122
Call trace:
run_timer_softirq+0x334/0x3d8
efi_header_end+0x114/0x234
irq_exit+0xd0/0xd8
__handle_domain_irq+0x60/0xb0
gic_handle_irq+0x58/0xa8
el1_irq+0xb8/0x180
arch_cpu_idle+0x10/0x18
do_idle+0x1d8/0x2b0
cpu_startup_entry+0x24/0x40
secondary_start_kernel+0x1b4/0x208
Code: f9000693 a9400660 f9000020 b4000040 (f9000401)
---[ end trace bb83ceeb4c482071 ]---
Kernel panic - not syncing: Fatal exception in interrupt
SMP: stopping secondary CPUs
SMP: failed to stop secondary CPUs 2-3
Kernel Offset: disabled
CPU features: 0x00002,2300aa30
Memory Limit: none
---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
It's found that stmmac_xmit() and stmmac_resume() sometimes might
run concurrently, possibly resulting in a race condition between
mod_timer() and setup_timer(), being called by stmmac_xmit() and
stmmac_resume() respectively.
Since the resume() runs setup_timer() every time, it'd be safer to
have del_timer_sync() in the suspend() as the counterpart.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18e4960c18 ]
The driver currently only calls netdev_set_tc_queue when the number of
TCs is greater than 1. Instead, the comparison should be greater than
or equal to 1. Even with 1 TC, we need to set the queue mapping.
This bug can cause warnings when the number of TCs is changed back to 1.
Fixes: 7809592d3e ("bnxt_en: Enable MSIX early in bnxt_init_one().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44efc78d0e ]
In order to fix XDP support if sw buffer management is used as fallback
for hw bm devices, define MVNETA_SKB_HEADROOM as maximum between
XDP_PACKET_HEADROOM and NET_SKB_PAD and let the hw aligns the IP header
to 4-byte boundary.
Fix rx_offset_correction initialization if mvneta_bm_port_init fails in
mvneta_resume routine
Fixes: 0db51da7a8 ("net: mvneta: add basic XDP support")
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cda2cab077 ]
Latest kernels get the phys_port_name via devlink, if
ndo_get_phys_port_name is not defined. To provide the phys_port_name
correctly, register devlink before registering netdev.
Also call devlink_port_type_eth_set() after registering netdev as
devlink port updates the netdev structure and notifies user.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6dd4b4f393 ]
An 'alloc_etherdev()' called is not ballanced by a corresponding
'free_netdev()' call in one error handling path.
Slighly reorder the error handling code to catch the missed case.
Fixes: c100e47caa ("mlxsw: minimal: Add ethtool support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02758cb6da ]
Fix xdp_result initialization in netsec_process_rx in order to not
increase rx counters if there is no bpf program attached to the xdp hook
and napi_gro_receive returns GRO_DROP
Fixes: ba2b232108 ("net: netsec: add XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5e82e3c89 ]
Fix possible use-after-free in in netsec_process_rx that can occurs if
the first packet is sent to the normal networking stack and the
following one is dropped by the bpf program attached to the xdp hook.
Fix the issue defining the skb pointer in the 'budget' loop
Fixes: ba2b232108 ("net: netsec: add XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 79572c98c5 ]
Recently XDP Support was added to the mvneta driver
for software buffer management only.
It is still possible to attach an XDP program if
hardware buffer management is used.
It is not doing anything at that point.
The patch disallows attaching XDP programs to mvneta
if hardware buffer management is used.
I am sorry about that. It is my first submission and I am having
some troubles with the format of my emails.
v4 -> v5:
- Remove extra tabs
v3 -> v4:
- Please ignore v3 I accidentally submitted
my other patch with git-send-mail and v4 is correct
v2 -> v3:
- My mailserver corrupted the patch
resubmission with git-send-email
v1 -> v2:
- Fixing the patches indentation
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl4rTdoACgkQSD+KveBX
+j5wiAgAtlGxIVKMpbJN7DIJNQ3rLGwTjPdVUFSRvHB+krVV9/ym02bIBIEphSPu
ZEF53eJMtJ0XIdUjvAyKA+zJg9p12vewbGpYV/LdjBNikHatMPGvR4grDgB9pnqT
tIxH6b4vzh5p/bMcP5l4yuVG6pf/ERdxQqsa93Op9xJzOkMH+A2KA/G32VHL2OmH
619hrWRVA/UVG0wUcOaX6ra+QA5EQ3lhcrvqL702k4JhIZPtG7Ndmm0+Z0nrDiIm
oXfc1236nc3emkijQczEZ+6oYiuYQ7WSKxZeS+8Bnmc3ZZ2w2RZrC7UCOadGzu12
+0XYfMsD2FWwEim52IZK/VMPtykjZw==
=i5Au
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-01-24
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
Merge conflict: once merge with net-next, a contextual conflict will
appear in drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c
since the code moved in net-next.
To resolve, just delete ALL of the conflicting hunk from net.
So sorry for the small mess ..
For -stable v5.4:
('net/mlx5: Update the list of the PCI supported devices')
('net/mlx5: Fix lowest FDB pool size')
('net/mlx5e: kTLS, Fix corner-case checks in TX resync flow')
('net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path')
('net/mlx5: Eswitch, Prevent ingress rate configuration of uplink rep')
('net/mlx5e: kTLS, Remove redundant posts in TX resync flow')
('net/mlx5: DR, Enable counter on non-fwd-dest objects')
('net/mlx5: DR, use non preemptible call to get the current cpu number')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cxgb3 driver for "Chelsio T3-based gigabit and 10Gb Ethernet
adapters" implements a custom ioctl as SIOCCHIOCTL/SIOCDEVPRIVATE in
cxgb_extension_ioctl().
One of the subcommands of the ioctl is CHELSIO_GET_MEM, which appears
to read memory directly out of the adapter and return it to userspace.
It's not entirely clear what the contents of the adapter memory
contains, but the assumption is that it shouldn't be accessible to all
users.
So add a CAP_NET_ADMIN check to the CHELSIO_GET_MEM case. Put it after
the is_offload() check, which matches two of the other subcommands in
the same function which also check for is_offload() and CAP_NET_ADMIN.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 7587935cfa ("net: bcmgenet: move NAPI initialization to
ring initialization") moved the code, this used to be
netif_tx_napi_add(), but we lost that small semantic change in the
process, restore that.
Fixes: 7587935cfa ("net: bcmgenet: move NAPI initialization to ring initialization")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic device API to get phy mode to fix probe failure
with ACPI based devices.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
