[ Upstream commit 86f271f22b ]
Errata #i2037 in AM65x/DRA80xM Processors Silicon Revision 1.0
(SPRZ452D_July 2018_Revised December 2019 [1]) mentions when an
inbound PCIe TLP spans more than two internal AXI 128-byte bursts,
the bus may corrupt the packet payload and the corrupt data may
cause associated applications or the processor to hang.
The workaround for Errata #i2037 is to limit the maximum read
request size and maximum payload size to 128 bytes. Add workaround
for Errata #i2037 here.
The errata and workaround is applicable only to AM65x SR 1.0 and
later versions of the silicon will have this fixed.
[1] -> https://www.ti.com/lit/er/sprz452i/sprz452i.pdf
Link: https://lore.kernel.org/linux-pci/16e1fcae-1ea7-46be-b157-096e05661b15@siemens.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9927c2cac ]
If IORESOURCE_BUS is not provided in Device Tree it will be fabricated in
of_pci_parse_bus_range(), so NULL pointer dereference should not happen
here.
But that's hard to verify, so check for NULL anyway.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Link: https://lore.kernel.org/linux-pci/20240503125705.46055-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a4bbcac11d upstream.
The LS7A chipset can be used as part of a PCIe Root Complex with
Loongson-3C6000 and similar CPUs. In this case, DEV_LS7A_PCIE_PORT5 has a
PCI_CLASS_BRIDGE_HOST class code, and it is a Type 0 Function whose config
space provides access to Root Complex registers.
The DEV_LS7A_PCIE_PORT5 has an MSI Capability, and its MSI Enable bit must
be set before other devices below the Root Complex can use MSI. This is
not the standard PCI behavior of MSI Enable, so the normal PCI MSI code
does not set it.
Set the DEV_LS7A_PCIE_PORT5 MSI Enable bit via a quirk so other devices
below the Root Complex can use MSI.
[kwilczynski: exit early to reduce indentation; commit log]
Link: https://lore.kernel.org/linux-pci/20240612065315.2048110-1-chenhuacai@loongson.cn
Signed-off-by: Sheng Wu <wusheng@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 840b7a5edf upstream.
Rockchip platforms use 'GPIO_ACTIVE_HIGH' flag in the devicetree definition
for ep_gpio. This means, whatever the logical value set by the driver for
the ep_gpio, physical line will output the same logic level.
For instance,
gpiod_set_value_cansleep(rockchip->ep_gpio, 0); --> Level low
gpiod_set_value_cansleep(rockchip->ep_gpio, 1); --> Level high
But while requesting the ep_gpio, GPIOD_OUT_HIGH flag is currently used.
Now, this also causes the physical line to output 'high' creating trouble
for endpoint devices during host reboot.
When host reboot happens, the ep_gpio will initially output 'low' due to
the GPIO getting reset to its POR value. Then during host controller probe,
it will output 'high' due to GPIOD_OUT_HIGH flag. Then during
rockchip_pcie_host_init_port(), it will first output 'low' and then 'high'
indicating the completion of controller initialization.
On the endpoint side, each output 'low' of ep_gpio is accounted for PERST#
assert and 'high' for PERST# deassert. With the above mentioned flow during
host reboot, endpoint will witness below state changes for PERST#:
(1) PERST# assert - GPIO POR state
(2) PERST# deassert - GPIOD_OUT_HIGH while requesting GPIO
(3) PERST# assert - rockchip_pcie_host_init_port()
(4) PERST# deassert - rockchip_pcie_host_init_port()
Now the time interval between (2) and (3) is very short as both happen
during the driver probe(), and this results in a race in the endpoint.
Because, before completing the PERST# deassertion in (2), endpoint got
another PERST# assert in (3).
A proper way to fix this issue is to change the GPIOD_OUT_HIGH flag in (2)
to GPIOD_OUT_LOW. Because the usual convention is to request the GPIO with
a state corresponding to its 'initial/default' value and let the driver
change the state of the GPIO when required.
As per that, the ep_gpio should be requested with GPIOD_OUT_LOW as it
corresponds to the POR value of '0' (PERST# assert in the endpoint). Then
the driver can change the state of the ep_gpio later in
rockchip_pcie_host_init_port() as per the initialization sequence.
This fixes the firmware crash issue in Qcom based modems connected to
Rockpro64 based board.
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Closes: https://lore.kernel.org/mhi/20240402045647.GG2933@thinkpad/
Link: https://lore.kernel.org/linux-pci/20240416-pci-rockchip-perst-fix-v1-1-4800b1d4d954@linaro.org
Reported-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28b8d7793b upstream.
PERST# is active low according to the PCIe specification.
However, the existing pcie-dw-rockchip.c driver does:
gpiod_set_value(..., 0); msleep(100); gpiod_set_value(..., 1);
when asserting + deasserting PERST#.
This is of course wrong, but because all the device trees for this
compatible string have also incorrectly marked this GPIO as ACTIVE_HIGH:
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3568*
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3588*
The actual toggling of PERST# is correct, and we cannot change it anyway,
since that would break device tree compatibility.
However, this driver does request the GPIO to be initialized as
GPIOD_OUT_HIGH, which does cause a silly sequence where PERST# gets
toggled back and forth for no good reason.
Fix this by requesting the GPIO to be initialized as GPIOD_OUT_LOW (which
for this driver means PERST# asserted).
This will avoid an unnecessary signal change where PERST# gets deasserted
(by devm_gpiod_get_optional()) and then gets asserted (by
rockchip_pcie_start_link()) just a few instructions later.
Before patch, debug prints on EP side, when booting RC:
[ 845.606810] pci: PERST# asserted by host!
[ 852.483985] pci: PERST# de-asserted by host!
[ 852.503041] pci: PERST# asserted by host!
[ 852.610318] pci: PERST# de-asserted by host!
After patch, debug prints on EP side, when booting RC:
[ 125.107921] pci: PERST# asserted by host!
[ 132.111429] pci: PERST# de-asserted by host!
This extra, very short, PERST# assertion + deassertion has been reported to
cause issues with certain WLAN controllers, e.g. RTL8822CE.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Link: https://lore.kernel.org/linux-pci/20240417164227.398901-1-cassel@kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fea93a3e5d upstream.
The intent of the code snippet is to always return 0 for both
PCI_INTERRUPT_LINE and PCI_INTERRUPT_PIN.
The check misses PCI_INTERRUPT_PIN. This patch fixes that.
This is discovered by this call in VFIO:
pci_read_config_byte(vdev->pdev, PCI_INTERRUPT_PIN, &pin);
The old code does not set *val to 0 because it misses the check for
PCI_INTERRUPT_PIN. Garbage is returned in that case.
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Link: https://lore.kernel.org/linux-pci/20240701202606.129606-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2a57ee0f2 ]
When PERST# assert and deassert happens on the PERST# supported platforms,
both iATU0 and iATU6 will map inbound window to BAR0. DMA will access the
area that was previously allocated (iATU0) for BAR0, instead of the new
area (iATU6) for BAR0.
Right now, this isn't an issue because both iATU0 and iATU6 should
translate inbound accesses to BAR0 to the same allocated memory area.
However, having two separate inbound mappings for the same BAR is a
disaster waiting to happen.
The mappings between PCI BAR and iATU inbound window are maintained in the
dw_pcie_ep::bar_to_atu[] array. While allocating a new inbound iATU map for
a BAR, dw_pcie_ep_inbound_atu() API checks for the availability of the
existing mapping in the array and if it is not found (i.e., value in the
array indexed by the BAR is found to be 0), it allocates a new map value
using find_first_zero_bit().
The issue is the existing logic failed to consider the fact that the map
value '0' is a valid value for BAR0, so find_first_zero_bit() will return
'0' as the map value for BAR0 (note that it returns the first zero bit
position).
Due to this, when PERST# assert + deassert happens on the PERST# supported
platforms, the inbound window allocation restarts from BAR0 and the
existing logic to find the BAR mapping will return '6' for BAR0 instead of
'0' due to the fact that it considers '0' as an invalid map value.
Fix this issue by always incrementing the map value before assigning to
bar_to_atu[] array and then decrementing it while fetching. This will make
sure that the map value '0' always represents the invalid mapping."
Fixes: 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Closes: https://lore.kernel.org/linux-pci/ZXsRp+Lzg3x%2Fnhk3@x1-carbon/
Link: https://lore.kernel.org/linux-pci/20240412160841.925927-1-Frank.Li@nxp.com
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 912315715d ]
All EP specific resources are enabled during PERST# deassert. As a counter
operation, all resources should be disabled during PERST# assert. There is
no point in skipping that if the link was not enabled.
This will also result in enablement of the resources twice if PERST# got
deasserted again. So remove the check from qcom_pcie_perst_assert() and
disable all the resources unconditionally.
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-1-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c93637e6a4 ]
Avoid large backtrace, it is sufficient to warn the user that there has
been a link problem. Either the link has failed and the system is in need
of maintenance, or the link continues to work and user has been informed.
The message from the warning can be looked up in the sources.
This makes an actual link issue less verbose.
First of all, this controller has a limitation in that the controller
driver has to assist the hardware with transition to L1 link state by
writing L1IATN to PMCTRL register, the L1 and L0 link state switching
is not fully automatic on this controller.
In case of an ASMedia ASM1062 PCIe SATA controller which does not support
ASPM, on entry to suspend or during platform pm_test, the SATA controller
enters D3hot state and the link enters L1 state. If the SATA controller
wakes up before rcar_pcie_wakeup() was called and returns to D0, the link
returns to L0 before the controller driver even started its transition to
L1 link state. At this point, the SATA controller did send an PM_ENTER_L1
DLLP to the PCIe controller and the PCIe controller received it, and the
PCIe controller did set PMSR PMEL1RX bit.
Once rcar_pcie_wakeup() is called, if the link is already back in L0 state
and PMEL1RX bit is set, the controller driver has no way to determine if
it should perform the link transition to L1 state, or treat the link as if
it is in L0 state. Currently the driver attempts to perform the transition
to L1 link state unconditionally, which in this specific case fails with a
PMSR L1FAEG poll timeout, however the link still works as it is already
back in L0 state.
Reduce this warning verbosity. In case the link is really broken, the
rcar_pcie_config_access() would fail, otherwise it will succeed and any
system with this controller and ASM1062 can suspend without generating
a backtrace.
Fixes: 84b5761462 ("PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()")
Link: https://lore.kernel.org/linux-pci/20240511235513.77301-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a231707a91 ]
If IORESOURCE_MEM is not provided in Device Tree due to
any error, resource_list_first_type() will return NULL and
pci_parse_request_of_pci_ranges() will just emit a warning.
This will cause a NULL pointer dereference. Fix this bug by adding NULL
return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f71c60ffd ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/linux-pci/20240505061517.11527-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ffa0e70b2 ]
After 6ab15b5e70 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), ks_pcie_v3_65_add_bus() enabled BAR 0 for both v3.65a and
v4.90a devices. On the AM654x SoC, which uses v4.90a, enabling BAR 0
causes Completion Timeouts when setting up MSI-X. These timeouts delay
boot of the AM654x by about 45 seconds.
Move the BAR 0 initialization to ks_pcie_msi_host_init(), which is only
used for v3.65a devices, and remove ks_pcie_v3_65_add_bus().
[bhelgaas: commit log]
Fixes: 6ab15b5e70 ("PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus")
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-3-s-vadapalli@ti.com
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Niklas Cassel <cassel@kernel.org>
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2dba285cab upstream.
Remove wrong mask on subsys_vendor_id. Both the Vendor ID and Subsystem
Vendor ID are u16 variables and are written to a u32 register of the
controller. The Subsystem Vendor ID was always 0 because the u16 value
was masked incorrectly with GENMASK(31,16) resulting in all lower 16
bits being set to 0 prior to the shift.
Remove both masks as they are unnecessary and set the register correctly
i.e., the lower 16-bits are the Vendor ID and the upper 16-bits are the
Subsystem Vendor ID.
This is documented in the RK3399 TRM section 17.6.7.1.17
[kwilczynski: removed unnecesary newline]
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/linux-pci/20240403144508.489835-1-rick.wertenbroek@gmail.com
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 19326006a2 ]
Tegra194 PCIe probe path is taking failure path in success case for
Endpoint mode. Return success from the switch case instead of going
into the failure path.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/linux-pci/20240408093053.3948634-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5ff74c1ef ]
For a physical PCI device that is passed through to a Hyper-V guest VM,
current code specifies the VMBus ring buffer size as 4 pages. But this
is an inappropriate dependency, since the amount of ring buffer space
needed is unrelated to PAGE_SIZE. For example, on x86 the ring buffer
size ends up as 16 Kbytes, while on ARM64 with 64 Kbyte pages, the ring
size bloats to 256 Kbytes. The ring buffer for PCI pass-thru devices
is used for only a few messages during device setup and removal, so any
space above a few Kbytes is wasted.
Fix this by declaring the ring buffer size to be a fixed 16 Kbytes.
Furthermore, use the VMBUS_RING_SIZE() macro so that the ring buffer
header is properly accounted for, and so the size is rounded up to a
page boundary, using the page size for which the kernel is built. While
w/64 Kbyte pages this results in a 64 Kbyte ring buffer header plus a
64 Kbyte ring buffer, that's the smallest possible with that page size.
It's still 128 Kbytes better than the current code.
Link: https://lore.kernel.org/linux-pci/20240216202240.251818-1-mhklinux@outlook.com
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Ilpo Jarvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72e34b8593 ]
The commit message in commit fc9a77040b ("PCI: designware-ep: Configure
Resizable BAR cap to advertise the smallest size") claims that it modifies
the Resizable BAR capability to only advertise support for 1 MB size BARs.
However, the commit writes all zeroes to PCI_REBAR_CAP (the register which
contains the possible BAR sizes that a BAR be resized to).
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
Set bit 4 in PCI_REBAR_CAP, so that we actually advertise support for a
1 MB BAR size.
Before:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB
BAR 1: current size: 1MB
BAR 2: current size: 1MB
BAR 3: current size: 1MB
BAR 4: current size: 1MB
BAR 5: current size: 1MB
After:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB, supported: 1MB
BAR 1: current size: 1MB, supported: 1MB
BAR 2: current size: 1MB, supported: 1MB
BAR 3: current size: 1MB, supported: 1MB
BAR 4: current size: 1MB, supported: 1MB
BAR 5: current size: 1MB, supported: 1MB
Fixes: fc9a77040b ("PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size")
Link: https://lore.kernel.org/linux-pci/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf79e33cdd ]
Qcom SoCs making use of ARM SMMU require BDF to SID translation table in
the driver to properly map the SID for the PCIe devices based on their BDF
identifier. This is currently achieved with the help of
qcom_pcie_config_sid_1_9_0() function for SoCs supporting the 1_9_0 config.
But With newer Qcom SoCs starting from SM8450, BDF to SID translation is
set to bypass mode by default in hardware. Due to this, the translation
table that is set in the qcom_pcie_config_sid_1_9_0() is essentially
unused and the default SID is used for all endpoints in SoCs starting from
SM8450.
This is a security concern and also warrants swapping the DeviceID in DT
while using the GIC ITS to handle MSIs from endpoints. The swapping is
currently done like below in DT when using GIC ITS:
/*
* MSIs for BDF (1:0.0) only works with Device ID 0x5980.
* Hence, the IDs are swapped.
*/
msi-map = <0x0 &gic_its 0x5981 0x1>,
<0x100 &gic_its 0x5980 0x1>;
Here, swapping of the DeviceIDs ensure that the endpoint with BDF (1:0.0)
gets the DeviceID 0x5980 which is associated with the default SID as per
the iommu mapping in DT. So MSIs were delivered with IDs swapped so far.
But this also means the Root Port (0:0.0) won't receive any MSIs (for PME,
AER etc...)
So let's fix these issues by clearing the BDF to SID bypass mode for all
SoCs making use of the 1_9_0 config. This allows the PCIe devices to use
the correct SID, thus avoiding the DeviceID swapping hack in DT and also
achieving the isolation between devices.
Fixes: 4c93988221 ("PCI: qcom: Add support for configuring BDF to SID mapping for SM8250")
Link: https://lore.kernel.org/linux-pci/20240307-pci-bdf-sid-fix-v1-1-9423a7e2d63c@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org # 5.11
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f70939871 ]
qcom_pcie_config_sid_sm8250() function no longer applies only to SM8250.
So let's rename it to reflect the actual IP version and also move its
definition to keep it sorted as per IP revisions.
Link: https://lore.kernel.org/r/20230316081117.14288-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Stable-dep-of: bf79e33cdd ("PCI: qcom: Enable BDF to SID translation properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17cf8661ee ]
The endpoint controller loses the Maximum Link Width and Supported Link Speed
value from the Link Capabilities Register - initially configured by the Reset
Configuration Word (RCW) - during a link-down or hot reset event.
Address this issue in the endpoint event handler.
Link: https://lore.kernel.org/r/20230720135834.1977616-2-Frank.Li@nxp.com
Fixes: a805770d8a ("PCI: layerscape: Add EP mode support")
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 061cbfab09 ]
Layerscape has PME interrupt, which can be used as linkup notifier. Set
CFG_READY bit of PEX_PF0_CONFIG to enable accesses from root complex when
linkup detected.
Link: https://lore.kernel.org/r/20230515151049.2797105-1-Frank.Li@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b5d1b4b46f upstream.
The "msg_addr" variable is u64. However, the "aligned_offset" is an
unsigned int. This means that when the code does:
msg_addr &= ~aligned_offset;
it will unintentionally zero out the high 32 bits. Use ALIGN_DOWN() to do
the alignment instead.
Fixes: 2217fffcd6 ("PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support")
Link: https://lore.kernel.org/r/af59c7ad-ab93-40f7-ad4a-7ac0b14d37f5@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ccc1318cf ]
When using the fls() helper, the translation table should be a power of
two; otherwise, the resulting value will not be correct.
For example, given fls(0x3e00000) - 1 = 25, the PCIe translation window
size will be set to 0x2000000 instead of the expected size 0x3e00000.
Fix the translation window by splitting the MMIO space into multiple tables
if its size is not a power of two.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231023081423.18559-1-jianjun.wang@mediatek.com
Fixes: d3bf75b579 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12ca110c6 ]
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4e11c29873 upstream.
We found a failure when using the iperf tool during WiFi performance
testing, where some MSIs were received while clearing the interrupt
status, and these MSIs cannot be serviced.
The interrupt status can be cleared even if the MSI status remains pending.
As such, given the edge-triggered interrupt type, its status should be
cleared before being dispatched to the handler of the underling device.
[kwilczynski: commit log, code comment wording]
Link: https://lore.kernel.org/linux-pci/20231211094923.31967-1-jianjun.wang@mediatek.com
Fixes: 43e6409db6 ("PCI: mediatek: Add MSI support for MT2712 and MT7622")
Signed-off-by: qizhong cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: rewrap comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2217fffcd6 upstream.
Commit 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org
Fixes: 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 5.7
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef61a04057 upstream.
This is a partial revert of 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS
increases") for MIPS-based Loongson.
Some MIPS Loongson systems don't support arbitrary Max_Read_Request_Size
(MRRS) settings. 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS
increases") worked around that by (1) assuming that firmware configured
MRRS to the maximum supported value and (2) preventing the PCI core from
increasing MRRS.
Unfortunately, some firmware doesn't set that maximum MRRS correctly, which
results in devices not being initialized correctly. One symptom, from the
Debian report below, is this:
ata4.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6 frozen
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/20:e8:00:f0:e1/00:00:00:00:00/40 tag 29 ncq dma 16384 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
Limit MRRS to 256 because MIPS Loongson with higher MRRS support is
considered rare.
This must be done at device enablement stage because the MRRS setting may
get lost if PCI_COMMAND_MASTER on the parent bridge is cleared, and we are
only sure parent bridge is enabled at this point.
Fixes: 8b3517f88f ("PCI: loongson: Prevent LS7A MRRS increases")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217680
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1035587
Link: https://lore.kernel.org/r/20231201115028.84351-1-jiaxun.yang@flygoat.com
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a07d2497ed ]
The DWC core driver exposes the write_dbi2() callback for writing to the
DBI2 registers in a vendor-specific way.
On the Qcom EP platforms, the DBI_CS2 bit in the ELBI region needs to be
asserted before writing to any DBI2 registers and deasserted once done.
So, let's implement the callback for the Qcom PCIe EP driver so that the
DBI2 writes are correctly handled in the hardware.
Without this callback, the DBI2 register writes like BAR size won't go
through and as a result, the default BAR size is set for all BARs.
[kwilczynski: commit log, renamed function to match the DWC convention]
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231025130029.74693-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Cc: stable@vger.kernel.org # 5.16+
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 83a939f0fd upstream.
With CONFIG_PCI_EXYNOS=y and exynos_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
This fixes the following warning by modpost:
WARNING: modpost: drivers/pci/controller/dwc/pci-exynos: section mismatch in reference: exynos_pcie_driver+0x8 (section: .data) -> exynos_pcie_remove (section: .exit.text)
(with ARCH=x86_64 W=1 allmodconfig).
Fixes: 340cba6092 ("pci: Add PCIe driver for Samsung Exynos")
Link: https://lore.kernel.org/r/20231001170254.2506508-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3064ef2e88 upstream.
With CONFIG_PCIE_KIRIN=y and kirin_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
This fixes the following warning by modpost:
drivers/pci/controller/dwc/pcie-kirin: section mismatch in reference: kirin_pcie_driver+0x8 (section: .data) -> kirin_pcie_remove (section: .exit.text)
(with ARCH=x86_64 W=1 allmodconfig).
Fixes: 000f60db78 ("PCI: kirin: Add support for a PHY layer")
Link: https://lore.kernel.org/r/20231001170254.2506508-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7994db905c upstream.
The __init annotation makes the ks_pcie_probe() function disappear after
booting completes. However a device can also be bound later. In that case,
we try to call ks_pcie_probe(), but the backing memory is likely already
overwritten.
The right thing to do is do always have the probe callback available. Note
that the (wrong) __refdata annotation prevented this issue to be noticed by
modpost.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Link: https://lore.kernel.org/r/20231001170254.2506508-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 200bddbb3f upstream.
With CONFIG_PCIE_KEYSTONE=y and ks_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
Note that this driver cannot be compiled as a module, so ks_pcie_remove()
was always discarded before this change and modpost couldn't warn about
this issue. Furthermore the __ref annotation also prevents a warning.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Link: https://lore.kernel.org/r/20231001170254.2506508-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 408599ec56 ]
mvebu_pcie_setup_hw() setups the Maximum Link Width field in the Link
Capabilities registers using an open-coded variant of FIELD_PREP() with
a literal in shift. Improve readability by using
FIELD_PREP(PCI_EXP_LNKCAP_MLW, ...).
Link: https://lore.kernel.org/r/20230919125648.1920-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 759574abd7 ]
Use FIELD_GET() to extract PCIe Negotiated Link Width field instead of
custom masking and shifting.
Similarly, change custom code that misleadingly used
PCI_EXP_LNKSTA_NLW_SHIFT to prepare value for PCI_EXP_LNKCAP write
to use FIELD_PREP() with correct field define (PCI_EXP_LNKCAP_MLW).
Link: https://lore.kernel.org/r/20230919125648.1920-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5827e17d05 ]
vmd_domain_reset() attempts to find whether the device may contain multiple
functions by checking 0x80 (Multi-Function Device), however, the hdr_type
variable has already been masked with PCI_HEADER_TYPE_MASK so the check can
never true.
To fix the issue, don't mask the read with PCI_HEADER_TYPE_MASK.
Fixes: 6aab562229 ("PCI: vmd: Clean up domain before enumeration")
Link: https://lore.kernel.org/r/20231003125300.5541-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6a878a54d0 upstream.
PARF_SLV_ADDR_SPACE_SIZE_2_3_3 is used by qcom_pcie_post_init_2_3_3().
This PCIe slave address space size register offset is 0x358 but was
incorrectly changed to 0x16c by 39171b33f6 ("PCI: qcom: Remove PCIE20_
prefix from register definitions").
This prevented access to slave address space registers like iATU, etc.,
so the IPQ8074 PCIe controller was not enumerated.
Revert back to the correct 0x358 offset and remove the unused
PARF_SLV_ADDR_SPACE_SIZE_2_3_3.
Fixes: 39171b33f6 ("PCI: qcom: Remove PCIE20_ prefix from register definitions")
Link: https://lore.kernel.org/r/20230919102948.1844909-1-quic_srichara@quicinc.com
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: stable@vger.kernel.org # v6.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 551a60e122 ]
The iMSI-RX module of the DW PCIe controller provides multiple sets of
MSI_CTRL_INT_i_* registers, and each set is capable of handling 32 MSI
interrupts. However, the fu740 PCIe controller driver only enabled one set
of MSI_CTRL_INT_i_* registers, as the total number of supported interrupts
was not specified.
Set the supported number of MSI vectors to enable all the MSI_CTRL_INT_i_*
registers on the fu740 PCIe core, allowing the system to fully utilize the
available MSI interrupts.
Link: https://lore.kernel.org/r/20230807055621.2431-1-yongxuan.wang@sifive.com
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f73eedc90b ]
During domain reset process vmd_domain_reset() clears PCI
configuration space of VMD root ports. But certain platform
has observed following errors and failed to boot.
...
DMAR: VT-d detected Invalidation Queue Error: Reason f
DMAR: VT-d detected Invalidation Time-out Error: SID ffff
DMAR: VT-d detected Invalidation Completion Error: SID ffff
DMAR: QI HEAD: UNKNOWN qw0 = 0x0, qw1 = 0x0
DMAR: QI PRIOR: UNKNOWN qw0 = 0x0, qw1 = 0x0
DMAR: Invalidation Time-out Error (ITE) cleared
The root cause is that memset_io() clears prefetchable memory base/limit
registers and prefetchable base/limit 32 bits registers sequentially.
This seems to be enabling prefetchable memory if the device disabled
prefetchable memory originally.
Here is an example (before memset_io()):
PCI configuration space for 10000:00:00.0:
86 80 30 20 06 00 10 00 04 00 04 06 00 00 01 00
00 00 00 00 00 00 00 00 00 01 01 00 00 00 00 20
00 00 00 00 01 00 01 00 ff ff ff ff 75 05 00 00
...
So, prefetchable memory is ffffffff00000000-575000fffff, which is
disabled. When memset_io() clears prefetchable base 32 bits register,
the prefetchable memory becomes 0000000000000000-575000fffff, which is
enabled and incorrect.
Here is the quote from section 7.5.1.3.9 of PCI Express Base 6.0 spec:
The Prefetchable Memory Limit register must be programmed to a smaller
value than the Prefetchable Memory Base register if there is no
prefetchable memory on the secondary side of the bridge.
This is believed to be the reason for the failure and in addition the
sequence of operation in vmd_domain_reset() is not following the PCIe
specs.
Disable the bridge window by executing a sequence of operations
borrowed from pci_disable_bridge_window() and pci_setup_bridge_io(),
that comply with the PCI specifications.
Link: https://lore.kernel.org/r/20230810215029.1177379-1-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc8b24c28b ]
The i.MX integration for the DesignWare PCI controller has a _host_exit()
operation which undoes everything that the _host_init() operation does but
does not wire this up as the host_deinit callback for the core, or call it
in any path other than suspend. This means that if we ever unwind the
initial probe of the device, for example because it fails, the regulator
core complains that the regulators for the device were left enabled:
imx6q-pcie 33800000.pcie: iATU: unroll T, 4 ob, 4 ib, align 64K, limit 16G
imx6q-pcie 33800000.pcie: Phy link never came up
imx6q-pcie 33800000.pcie: Phy link never came up
imx6q-pcie: probe of 33800000.pcie failed with error -110
------------[ cut here ]------------
WARNING: CPU: 2 PID: 46 at drivers/regulator/core.c:2396 _regulator_put+0x110/0x128
Wire up the callback so that the core can clean up after itself.
Link: https://lore.kernel.org/r/20230731-pci-imx-regulator-cleanup-v2-1-fc8fa5c9893d@kernel.org
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 04bbe86324 upstream.
When a Linux VM with an assigned PCI device runs on Hyper-V, if the PCI
device driver is not loaded yet (i.e. MSI-X/MSI is not enabled on the
device yet), doing a VM hibernation triggers a panic in
hv_pci_restore_msi_msg() -> msi_lock_descs(&pdev->dev), because
pdev->dev.msi.data is still NULL.
Avoid the panic by checking if MSI-X/MSI is enabled.
Link: https://lore.kernel.org/r/20230816175939.21566-1-decui@microsoft.com
Fixes: dc2b453290 ("PCI: hv: Rework MSI handling")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: sathyanarayanan.kuppuswamy@linux.intel.com
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdb50033dd upstream.
A 32-bit mask was used on the 64-bit PCI address used for mapping MSIs.
This would result in the upper 32 bits being unintentionally zeroed and
MSIs getting mapped to incorrect PCI addresses if the address had any
of the upper bits set.
Replace 32-bit mask by appropriate 64-bit mask.
[kwilczynski: use GENMASK_ULL() over GENMASK() for 32-bit compatibility]
Fixes: dc73ed0f1b ("PCI: rockchip: Fix window mapping and address translation for endpoint")
Closes: https://lore.kernel.org/linux-pci/8d19e5b7-8fa0-44a4-90e2-9bb06f5eb694@moroto.mountain
Link: https://lore.kernel.org/linux-pci/20230703085845.2052008-1-rick.wertenbroek@gmail.com
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d473a5a26 ]
The SEC and DED interrupt bits are laid out the wrong way round so the SEC
interrupt handler attempts to mask, unmask, and clear the DED interrupt
and vice versa. Correct the bit offsets so that each interrupt handler
operates properly.
Link: https://lore.kernel.org/r/20230728131401.1615724-2-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9cbc06049 ]
Currently, as part of the qcom_pcie_perst_deassert() function, instead
of writing the updated value to clear PARF_MSTR_AXI_CLK_EN, the variable
"val" is re-read.
This must be fixed to ensure that the master clock supplied to the MHI
bus is correctly gated during L1.1/L1.2 to save power.
Thus, replace the line that re-reads "val" with a line that writes the
updated value to the register to clear PARF_MSTR_AXI_CLK_EN.
[kwilczynski: commit log]
Fixes: c457ac029e ("PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS")
Link: https://lore.kernel.org/linux-pci/20230627141036.11600-1-manivannan.sadhasivam@linaro.org
Reported-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8650c0c2a ]
The apple_pcie_setup_port() function computes ilog2(pcie->nvecs) to set
up the number of MSIs available for each port. However, it's called
before apple_msi_init(), which initializes pcie->nvecs.
Luckily, pcie->nvecs is part of kzalloc()-ed structure and, as such,
initialized as zero. ilog2(0) happens to be 0xffffffff which then simply
configures more MSIs in hardware than we have. This doesn't break
anything because we never hand out those vectors.
Thus, swap the order of the two calls so that the correctly initialized
value is then used.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20230311133453.63246-1-sven@svenpeter.dev
Fixes: 476c41ed45 ("PCI: apple: Implement MSI support")
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ebfde1584d upstream.
After commit 4fb8e46c1b ("PCI: tegra194: Enable support for 256 Byte
payload"), we initialize MPS=256 for tegra194 Root Ports before enumerating
the hierarchy.
Consider an Endpoint that supports only MPS=128. In the default situation
(CONFIG_PCIE_BUS_DEFAULT set and no "pci=pcie_bus_*" parameter), Linux
tries to configure the MPS of every device to match the upstream bridge.
If the Endpoint is directly below the Root Port, Linux can reduce the Root
Port MPS to 128 to match the Endpoint. But if there's a switch in the
middle, Linux doesn't reduce the Root Port MPS because other devices below
the switch may already be configured with MPS larger than 128.
This scenario results in uncorrectable Malformed TLP errors if the Root
Port sends TLPs with payloads larger than 128 bytes. These errors can
be avoided by using the "pci=pcie_bus_safe" parameter, but it doesn't
seem to be a good idea to always have this parameter even for basic
functionality to work.
Revert commit 4fb8e46c1b ("PCI: tegra194: Enable support for 256 Byte
payload") so the Root Ports default to MPS=128, which all devices
support.
If peer-to-peer DMA is not required, one can use "pci=pcie_bus_perf" to
get the benefit of larger MPS settings.
[bhelgaas: commit log; kwilczynski: retain "u16 val_16" declaration at
the top, add missing acked by tag]
Fixes: 4fb8e46c1b ("PCI: tegra194: Enable support for 256 Byte payload")
Link: https://lore.kernel.org/linux-pci/20230619102604.3735001-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org # v6.0-rc1+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 205b3d02d5 ]
Add check to fix the possible array out of bounds violation by
making speed equal to GEN1_CORE_CLK_FREQ when its value is more
than the size of "pcie_gen_freq" array. This array has size of
four but possible speed (CLS) values are from "0 to 0xF". So,
"speed - 1" values are "-1 to 0xE".
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Link: https://lore.kernel.org/lkml/72b9168b-d4d6-4312-32ea-69358df2f2d0@nvidia.com/
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a52587e0be ]
The RK3399 PCIe endpoint controller cannot generate MSI-X IRQs.
This is documented in the RK3399 technical reference manual (TRM)
section 17.5.9 "Interrupt Support".
MSI-X capability should therefore not be advertised. Remove the
MSI-X capability by editing the capability linked-list. The
previous entry is the MSI capability, therefore get the next
entry from the MSI-X capability entry and set it as next entry
for the MSI capability. This in effect removes MSI-X from the list.
Linked list before : MSI cap -> MSI-X cap -> PCIe Device cap -> ...
Linked list now : MSI cap -> PCIe Device cap -> ...
Link: https://lore.kernel.org/r/20230418074700.1083505-11-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc73ed0f1b ]
The RK3399 PCI endpoint core has 33 windows for PCIe space, now in the
driver up to 32 fixed size (1M) windows are used and pages are allocated
and mapped accordingly. The driver first used a single window and allocated
space inside which caused translation issues (between CPU space and PCI
space) because a window can only have a single translation at a given
time, which if multiple pages are allocated inside will cause conflicts.
Now each window is a single region of 1M which will always guarantee that
the translation is not in conflict.
Set the translation register addresses for physical function. As documented
in the technical reference manual (TRM) section 17.5.5 "PCIe Address
Translation" and section 17.6.8 "Address Translation Registers Description"
Link: https://lore.kernel.org/r/20230418074700.1083505-9-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92a9c57c32 ]
Remove write accesses to registers that are marked "unused" (and
therefore read-only) in the technical reference manual (TRM)
(see RK3399 TRM 17.6.8.1)
Link: https://lore.kernel.org/r/20230418074700.1083505-2-rick.wertenbroek@gmail.com
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Stable-dep-of: dc73ed0f1b ("PCI: rockchip: Fix window mapping and address translation for endpoint")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7e6689b34a upstream.
The address translation unit of the rockchip EP controller does not use
the lower 8 bits of a PCIe-space address to map local memory. Thus we
must set the align feature field to 256 to let the user know about this
constraint.
Link: https://lore.kernel.org/r/20230418074700.1083505-12-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8962b2cb39 upstream.
Previously u16 variables were used to access 32-bit registers, this
resulted in not all of the data being read from the registers. Also
the left shift of more than 16-bits would result in moving data out
of the variable. Use u32 variables to access 32-bit registers
Link: https://lore.kernel.org/r/20230418074700.1083505-10-rick.wertenbroek@gmail.com
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
