[ Upstream commit c8b8a3c601 ]
The MT7530 switch from the MT7621 SoC has 2 ports which can be set up as
internal: port 5 and 6. Arınç reports that the GMAC1 attached to port 5
receives corrupted frames, unless port 6 (attached to GMAC0) has been
brought up by the driver. This is true regardless of whether port 5 is
used as a user port or as a CPU port (carrying DSA tags).
Offline debugging (blind for me) which began in the linked thread showed
experimentally that the configuration done by the driver for port 6
contains a step which is needed by port 5 as well - the write to
CORE_GSWPLL_GRP2 (note that I've no idea as to what it does, apart from
the comment "Set core clock into 500Mhz"). Prints put by Arınç show that
the reset value of CORE_GSWPLL_GRP2 is RG_GSWPLL_POSDIV_500M(1) |
RG_GSWPLL_FBKDIV_500M(40) (0x128), both on the MCM MT7530 from the
MT7621 SoC, as well as on the standalone MT7530 from MT7623NI Bananapi
BPI-R2. Apparently, port 5 on the standalone MT7530 can work under both
values of the register, while on the MT7621 SoC it cannot.
The call path that triggers the register write is:
mt753x_phylink_mac_config() for port 6
-> mt753x_pad_setup()
-> mt7530_pad_clk_setup()
so this fully explains the behavior noticed by Arınç, that bringing port
6 up is necessary.
The simplest fix for the problem is to extract the register writes which
are needed for both port 5 and 6 into a common mt7530_pll_setup()
function, which is called at mt7530_setup() time, immediately after
switch reset. We can argue that this mirrors the code layout introduced
in mt7531_setup() by commit 42bc4fafe3 ("net: mt7531: only do PLL once
after the reset"), in that the PLL setup has the exact same positioning,
and further work to consolidate the separate setup() functions is not
hindered.
Testing confirms that:
- the slight reordering of writes to MT7530_P6ECR and to
CORE_GSWPLL_GRP1 / CORE_GSWPLL_GRP2 introduced by this change does not
appear to cause problems for the operation of port 6 on MT7621 and on
MT7623 (where port 5 also always worked)
- packets sent through port 5 are not corrupted anymore, regardless of
whether port 6 is enabled by phylink or not (or even present in the
device tree)
My algorithm for determining the Fixes: tag is as follows. Testing shows
that some logic from mt7530_pad_clk_setup() is needed even for port 5.
Prior to commit ca366d6c88 ("net: dsa: mt7530: Convert to PHYLINK
API"), a call did exist for all phy_is_pseudo_fixed_link() ports - so
port 5 included. That commit replaced it with a temporary "Port 5 is not
supported!" comment, and the following commit 38f790a805 ("net: dsa:
mt7530: Add support for port 5") replaced that comment with a
configuration procedure in mt7530_setup_port5() which was insufficient
for port 5 to work. I'm laying the blame on the patch that claimed
support for port 5, although one would have also needed the change from
commit c3b8e07909 ("net: dsa: mt7530: setup core clock even in TRGMII
mode") for the write to be performed completely independently from port
6's configuration.
Thanks go to Arınç for describing the problem, for debugging and for
testing.
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/netdev/f297c2c4-6e7c-57ac-2394-f6025d309b9d@arinc9.com/
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230307155411.868573-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea9dd2e5c6 ]
NDC caches contexts of frequently used queue's (Rx and Tx queues)
contexts. Due to a HW errata when NDC detects fault/poision while
accessing contexts it could go into an illegal state where a cache
line could get locked forever. To makesure all cache lines in NDC
are available for optimum performance upon fault/lockerror/posion
errors scan through all cache lines in NDC and clear the lock bit.
Fixes: 4a3581cd59 ("octeontx2-af: NPA AQ instruction enqueue support")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f5c5a790e ]
With older compilers like gcc-9, the calculation of the vlan
priority field causes a false-positive warning from the byteswap:
In file included from drivers/net/ethernet/intel/ice/ice_tc_lib.c:4:
drivers/net/ethernet/intel/ice/ice_tc_lib.c: In function 'ice_parse_cls_flower':
include/uapi/linux/swab.h:15:15: error: integer overflow in expression '(int)(short unsigned int)((int)match.key-><U67c8>.<U6698>.vlan_priority << 13) & 57344 & 255' of type 'int' results in '0' [-Werror=overflow]
15 | (((__u16)(x) & (__u16)0x00ffU) << 8) | \
| ~~~~~~~~~~~~^~~~~~~~~~~~~~~~~
include/uapi/linux/swab.h:106:2: note: in expansion of macro '___constant_swab16'
106 | ___constant_swab16(x) : \
| ^~~~~~~~~~~~~~~~~~
include/uapi/linux/byteorder/little_endian.h:42:43: note: in expansion of macro '__swab16'
42 | #define __cpu_to_be16(x) ((__force __be16)__swab16((x)))
| ^~~~~~~~
include/linux/byteorder/generic.h:96:21: note: in expansion of macro '__cpu_to_be16'
96 | #define cpu_to_be16 __cpu_to_be16
| ^~~~~~~~~~~~~
drivers/net/ethernet/intel/ice/ice_tc_lib.c:1458:5: note: in expansion of macro 'cpu_to_be16'
1458 | cpu_to_be16((match.key->vlan_priority <<
| ^~~~~~~~~~~
After a change to be16_encode_bits(), the code becomes more
readable to both people and compilers, which avoids the warning.
Fixes: 34800178b3 ("ice: Add support for VLAN priority filters in switchdev")
Suggested-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef3f92e8a ]
When creating the TLV to send to the FW for configuring DSCP mode PFC,the
PFCENABLE field was being masked with a 4 bit mask (0xF), but this is an 8
bit bitmask for enabled classes for PFC. This means that traffic classes
4-7 could not be enabled for PFC.
Remove the mask completely, as it is not necessary, as we are assigning 8
bits to an 8 bit field.
Fixes: 2a87bd73e5 ("ice: Add DSCP support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 193250ace2 ]
Fix data corruption issue with SerDes connected PHYs operating at 1.25
Gbps speed where we could previously observe about 30% packet loss while
the bad packet counter was increasing.
As almost all boards with MediaTek MT7622 or MT7986 use either the MT7531
switch IC operating at 3.125Gbps SerDes rate or single-port PHYs using
rate-adaptation to 2500Base-X mode, this issue only got exposed now when
we started trying to use SFP modules operating with 1.25 Gbps with the
BananaPi R3 board.
The fix is to set bit 12 which disables the RX FIFO clear function when
setting up MAC MCR, MediaTek SDK did the same change stating:
"If without this patch, kernel might receive invalid packets that are
corrupted by GMAC."[1]
[1]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/d8a2975939a12686c4a95c40db21efdc3f821f63
Fixes: 42c03844e9 ("net-next: mediatek: add support for MediaTek MT7622 SoC")
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/138da2735f92c8b6f8578ec2e5a794ee515b665f.1677937317.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58aac3a2ef ]
Currently link up can't be detected in forced mode if polling
isn't used. Only link up interrupt source we have is aneg
complete which isn't applicable in forced mode. Therefore we
have to use energy-on as link up indicator.
Fixes: 7365494550 ("net: phy: smsc: skip ENERGYON interrupt if disabled")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit accd7e2369 ]
The driver needs to keep track of all the possible concurrent TPA (GRO/LRO)
completions on the aggregation ring. On P5 chips, the maximum number
of concurrent TPA is 256 and the amount of memory we allocate is order-5
on systems using 4K pages. Memory allocation failure has been reported:
NetworkManager: page allocation failure: order:5, mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null),cpuset=/,mems_allowed=0-1
CPU: 15 PID: 2995 Comm: NetworkManager Kdump: loaded Not tainted 5.10.156 #1
Hardware name: Dell Inc. PowerEdge R660/0M1CC5, BIOS 0.2.25 08/12/2022
Call Trace:
dump_stack+0x57/0x6e
warn_alloc.cold.120+0x7b/0xdd
? _cond_resched+0x15/0x30
? __alloc_pages_direct_compact+0x15f/0x170
__alloc_pages_slowpath.constprop.108+0xc58/0xc70
__alloc_pages_nodemask+0x2d0/0x300
kmalloc_order+0x24/0xe0
kmalloc_order_trace+0x19/0x80
bnxt_alloc_mem+0x1150/0x15c0 [bnxt_en]
? bnxt_get_func_stat_ctxs+0x13/0x60 [bnxt_en]
__bnxt_open_nic+0x12e/0x780 [bnxt_en]
bnxt_open+0x10b/0x240 [bnxt_en]
__dev_open+0xe9/0x180
__dev_change_flags+0x1af/0x220
dev_change_flags+0x21/0x60
do_setlink+0x35c/0x1100
Instead of allocating this big chunk of memory and dividing it up for the
concurrent TPA instances, allocate each small chunk separately for each
TPA instance. This will reduce it to order-0 allocations.
Fixes: 79632e9ba3 ("bnxt_en: Expand bnxt_tpa_info struct to support 57500 chips.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9334b702a ]
When MAC is not support PMT, driver will check PHY's WoL capability
and set device wakeup capability in stmmac_init_phy(). We can enable
the WoL through ethtool, the driver would enable the device wake up
flag. Now the device_may_wakeup() return true.
But if there is a way which enable the PHY's WoL capability derectly,
like in BIOS. The driver would not know the enable thing and would not
set the device wake up flag. The phy_suspend may failed like this:
[ 32.409063] PM: dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x50 returns -16
[ 32.409065] PM: Device stmmac-1:00 failed to suspend: error -16
[ 32.409067] PM: Some devices failed to suspend, or early wake event detected
Add to set the device wakeup enable flag according to the get_wol
function result in PHY can fix the error in this scene.
v2: add a Fixes tag.
Fixes: 1d8e5b0f3f ("net: stmmac: Support WOL with phy")
Signed-off-by: Rongguang Wei <weirongguang@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e57cf3639c ]
Move the LAN7800 internal phy (phy ID 0x0007c132) specific register
accesses to the phy driver (microchip.c).
Fix the error reported by Enguerrand de Ribaucourt in December 2022,
"Some operations during the cable switch workaround modify the register
LAN88XX_INT_MASK of the PHY. However, this register is specific to the
LAN8835 PHY. For instance, if a DP8322I PHY is connected to the LAN7801,
that register (0x19), corresponds to the LED and MAC address
configuration, resulting in unapropriate behavior."
I did not test with the DP8322I PHY, but I tested with an EVB-LAN7800
with the internal PHY.
Fixes: 14437e3fa2 ("lan78xx: workaround of forced 100 Full/Half duplex mode error")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230301154307.30438-1-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81563d8548 ]
When the police was removed from the port, then it was trying to
remove the police from the police id and not from the actual
police index.
The police id represents the id of the police and police index
represents the position in HW where the police is situated.
The port police id can be any number while the port police index
is a number based on the port chip port.
Fix this by deleting the police from HW that is situated at the
police index and not police id.
Fixes: 5390334b59 ("net: lan966x: Add port police support using tc-matchall")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f99e6d7c4e ]
While bringing hardware up we should perform a full reset including the
switch bit (BGMAC_BCMA_IOCTL_SW_RESET aka SICF_SWRST). It's what
specification says and what reference driver does.
This seems to be critical for the BCM5358. Without this hardware doesn't
get initialized properly and doesn't seem to transmit or receive any
packets.
Originally bgmac was calling bgmac_chip_reset() before setting
"has_robosw" property which resulted in expected behaviour. That has
changed as a side effect of adding platform device support which
regressed BCM5358 support.
Fixes: f6a95a2495 ("net: ethernet: bgmac: Add platform device support")
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230227091156.19509-1-zajec5@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 940af26132 ]
The blamed commit did not properly convert the resource start/end format
into the DEFINE_RES_MEM_NAMED() start/length format, resulting in a
resource for vsc9959_imdio_res which is much longer than expected:
$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
1f8140000-1f815ffff : 0000:00:00.5
1f8148030-1f815006f : imdio
vs (correct)
$ cat /proc/iomem
1f8000000-1f815ffff : pcie@1f0000000
1f8140000-1f815ffff : 0000:00:00.5
1f8148030-1f814803f : imdio
Luckily it's not big enough to exceed the size of the parent resource
(pci_resource_end(pdev, VSC9959_IMDIO_PCI_BAR)), and it doesn't overlap
with anything else that the Linux driver uses currently, so the larger
than expected size isn't a practical problem that I can see. Although it
is clearly wrong in the /proc/iomem output.
Fixes: 044d447a80 ("net: dsa: felix: use DEFINE_RES_MEM_NAMED for resources")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0322ef49c1 ]
During the refactoring in the commit below, vsc9953_mdio_read() was
replaced with mscc_miim_read(), which has one extra step: it checks for
the MSCC_MIIM_DATA_ERROR bits before returning the result.
On T1040RDB, there are 8 QSGMII PCSes belonging to the switch, and they
are organized in 2 groups. First group responds to MDIO addresses 4-7
because QSGMIIACR1[MDEV_PORT] is 1, and the second group responds to
MDIO addresses 8-11 because QSGMIIBCR1[MDEV_PORT] is 2. I have double
checked that these values are correctly set in the SERDES, as well as
PCCR1[QSGMA_CFG] and PCCR1[QSGMB_CFG] are both 0b01.
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 8 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 8 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 9 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 9 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 10 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 10 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 11 reg 0x1 MIIM_DATA 0x2d
mscc_miim_read: phyad 11 reg 0x5 MIIM_DATA 0x5801
mscc_miim_read: phyad 4 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 4 reg 0x5 MIIM_DATA 0x3da01, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 5 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 5 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 6 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 6 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
mscc_miim_read: phyad 7 reg 0x1 MIIM_DATA 0x3002d, ERROR
mscc_miim_read: phyad 7 reg 0x5 MIIM_DATA 0x35801, ERROR
As can be seen, the data in MIIM_DATA is still valid despite having the
MSCC_MIIM_DATA_ERROR bits set. The driver as introduced in commit
84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953
switch") was ignoring these bits, perhaps deliberately (although
unbeknownst to me).
This is an old IP and the hardware team cannot seem to be able to help
me track down a plausible reason for these failures. I'll keep
investigating, but in the meantime, this is a direct regression which
must be restored to a working state.
The only thing I can do is keep ignoring the errors as before.
Fixes: b996584523 ("net: dsa: ocelot: felix: utilize shared mscc-miim driver for indirect MDIO access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d28a06d7db ]
On success, mlx5_geneve_tlv_option_create returns non negative
Geneve object id. In case the object id is positive value the
caller functions will handle it as an error (non zero) and
will fail to offload the Geneve rule.
Fix this by changing caller function ,mlx5_geneve_tlv_option_add,
to return 0 in case valid non negative object id was provided.
Fixes: 0ccc171ea6 ("net/mlx5: Geneve, Manage Geneve TLV options")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1ed30c8c0 ]
Currently, during the early stages of their unloading, particularly
during SRIOV disablement, PFs/ECPFs wait on the release of all of
their VFs memory pages. Furthermore, ECPFs are considered the page
supplier for host VFs, hence the host VFs memory pages are freed only
during ECPF cleanup when host interfaces get disabled.
Thus, disabling SRIOV early in unload timeline causes the DPU ECPF
to stall on driver unload while waiting on the release of host VF pages
that won't be freed before host interfaces get disabled later on.
Therefore, for ECPFs, wait on the release of VFs pages only after the
disablement of host PFs during ECPF cleanup flow. Then, host PFs and VFs
are disabled and their memory shall be freed accordingly.
Fixes: 143a41d762 ("net/mlx5: Disable SRIOV before PF removal")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a50cf1e8e ]
Fifo indexes are not checked during pop operations and it leads to
potential use-after-free when poping from empty queue. Such case was
possible during re-sync action. WARN_ON_ONCE covers future cases.
There were out-of-order cqe spotted which lead to drain of the queue and
use-after-free because of lack of fifo pointers check. Special check and
counter are added to avoid resync operation if SKB could not exist in the
fifo because of OOO cqe (skb_id must be between consumer and producer
index).
Fixes: 58a518948f ("net/mlx5e: Add resiliency for PTP TX port timestamp")
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e435941b1d ]
During ptp resync operation SKBs were poped from the fifo but were never
freed neither by napi_consume nor by dev_kfree_skb_any. Add call to
napi_consume_skb to properly free SKBs.
Another leak was happening because mlx5e_skb_fifo_has_room() had an error
in the check. Comparing free running counters works well unless C promotes
the types to something wider than the counter. In this case counters are
u16 but the result of the substraction is promouted to int and it causes
wrong result (negative value) of the check when producer have already
overlapped but consumer haven't yet. Explicit cast to u16 fixes the issue.
Fixes: 58a518948f ("net/mlx5e: Add resiliency for PTP TX port timestamp")
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee0a735fd9 ]
devm_request_region is for I/O regions. Use devm_request_mem_region
instead. This fixes the driver failing to probe since 99df45c9e0
("sunhme: fix an IS_ERR() vs NULL check in probe"), which checked the
result.
Fixes: 914d9b2711 ("sunhme: switch to devres")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230222204242.2658247-1-seanga2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edea0c5a99 ]
When checksum offload is disabled in the driver via ethtool,
the PTP 1-step sync packets contain incorrect checksum, since
the stack calculates the checksum before driver updates
PTP timestamp field in the packet. This results in PTP packets
getting dropped at the other end. This patch fixes the issue by
re-calculating the UDP checksum after updating PTP
timestamp field in the driver.
Fixes: 2958d17a89 ("octeontx2-pf: Add support for ptp 1-step mode on CN10K silicon")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Link: https://lore.kernel.org/r/20230222113600.1965116-1-saikrishnag@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aaa3c08ee0 upstream.
Even after commit 908d4bb7c5 ("qede: fix interrupt coalescing
configuration"), some entries of the coal_entry array may theoretically
be used uninitialized:
1. qede_alloc_fp_array() allocates QEDE_MAX_RSS_CNT entries for
coal_entry. The initial allocation uses kcalloc, so everything is
initialized.
2. The user sets a small number of queues (ethtool -L).
coal_entry is reallocated for the actual small number of queues.
3. The user sets a bigger number of queues.
coal_entry is reallocated bigger. The added entries are not
necessarily initialized.
In practice, the reallocations will actually keep using the originally
allocated region of memory, but we should not rely on it.
The reallocation is unnecessary. coal_entry can always have
QEDE_MAX_RSS_CNT entries.
Fixes: 908d4bb7c5 ("qede: fix interrupt coalescing configuration")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Nacked-by: Manish Chopra <manishc@marvell.com>
Acked-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 908d4bb7c5 upstream.
On default driver load device gets configured with unexpected
higher interrupt coalescing values instead of default expected
values as memory allocated from krealloc() is not supposed to
be zeroed out and may contain garbage values.
Fix this by allocating the memory of required size first with
kcalloc() and then use krealloc() to resize and preserve the
contents across down/up of the interface.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Fixes: b0ec5489c4 ("qede: preserve per queue stats across up/down of interface")
Cc: stable@vger.kernel.org
Cc: Bhaskar Upadhaya <bupadhaya@marvell.com>
Cc: David S. Miller <davem@davemloft.net>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2160054
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c15430822 upstream.
When ath11k runs into internal errors upon suspend,
it returns an error code to pci_pm_suspend, which
aborts the entire system suspend.
The driver should not abort system suspend, but should
keep its internal errors to itself, and allow the system
to suspend. Otherwise, a user can suspend a laptop
by closing the lid and sealing it into a case, assuming
that is will suspend, rather than heating up and draining
the battery when in transit.
In practice, the ath11k device seems to have plenty of transient
errors, and subsequent suspend cycles after this failure
often succeed.
https://bugzilla.kernel.org/show_bug.cgi?id=216968
Fixes: d1b0c33850 ("ath11k: implement suspend for QCA6390 PCI devices")
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230201183201.14431-1-len.brown@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a86aa9a18 upstream.
The Realtek rate control algorithm goes back and forth a lot between
the highest and the lowest rate it's allowed to use. This is due to
a lot of frames being dropped because the retry limits set by
IEEE80211_CONF_CHANGE_RETRY_LIMITS are too low. (Experimentally, they
are 4 for long frames and 7 for short frames.)
The vendor drivers hardcode the value 48 for both retry limits (for
station mode), which makes dropped frames very rare and thus the rate
control is more stable.
Because most Realtek chips handle the rate control in the firmware,
which can't be modified, ignore the limits set by
IEEE80211_CONF_CHANGE_RETRY_LIMITS and use the value 48 (set during
chip initialisation), same as the vendor drivers.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/477d745b-6bac-111d-403c-487fc19aa30d@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a267bc5ea upstream.
Use power state to decide whether we can enter or leave IPS accurately,
and then prevent to power on/off twice.
The commit 6bf3a08340 ("wifi: rtw88: add flag check before enter or leave IPS")
would like to prevent this as well, but it still can't entirely handle all
cases. The exception is that WiFi gets connected and does suspend/resume,
it will power on twice and cause it failed to power on after resuming,
like:
rtw_8723de 0000:03:00.0: failed to poll offset=0x6 mask=0x2 value=0x2
rtw_8723de 0000:03:00.0: mac power on failed
rtw_8723de 0000:03:00.0: failed to power on mac
rtw_8723de 0000:03:00.0: leave idle state failed
rtw_8723de 0000:03:00.0: failed to leave ips state
rtw_8723de 0000:03:00.0: failed to leave idle state
rtw_8723de 0000:03:00.0: failed to send h2c command
To fix this, introduce new flag RTW_FLAG_POWERON to reflect power state,
and call rtw_mac_pre_system_cfg() to configure registers properly between
power-off/-on.
Reported-by: Paul Gover <pmw.gover@yahoo.co.uk>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217016
Fixes: 6bf3a08340 ("wifi: rtw88: add flag check before enter or leave IPS")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230216053633.20366-1-pkshih@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6015bf3ff upstream.
Fixing transmission failure which results in
"authentication with ... timed out". This can be
fixed by disable the REG_TXPAUSE.
Signed-off-by: Jun ASAKA <JunASAKA@zzy040330.moe>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221217030659.12577-1-JunASAKA@zzy040330.moe
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dca5161f9b ]
Completion responses to SEND_RNDIS_PKT messages are currently processed
regardless of the status in the response, so that resources associated
with the request are freed. While this is appropriate, code bugs that
cause sending a malformed message, or errors on the Hyper-V host, go
undetected. Fix this by checking the status and outputting a rate-limited
message if there is an error.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1676264881-48928-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c074da21dd ]
Only 8852C chip has valid pages on RTW89_DBG_SEL_MAC_30. To other chips,
this section is an address hole. It will lead to crash if trying to access
this section on chips except for 8852C. So, we avoid that.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230119063529.61563-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b88b47e89 ]
Free rx_head skb in mt76_dma_rx_cleanup routine in order to avoid
possible memory leak at module unload.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c0862c2c9 ]
Occasionnaly we may get oversized packets from the hardware which
exceed the nomimal 2KiB buffer size we allocate SKBs with. Add an early
check which drops the packet to avoid invoking skb_over_panic() and move
on to processing the next packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a8d013e90 ]
There were a few places we had missed checking the VSI type to make sure
it was definitely a PF VSI, before calling setup functions intended only
for the PF VSI.
This doesn't fix any explicit bugs but cleans up the code in a few
places and removes one explicit != vsi->type check that can be
superseded by this code (it's a super set)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aa4318c3a ]
The PHY provides only 39b timestamp. With current timing
implementation, we discard lower 7b, leaving 32b timestamp.
The driver reconstructs the full 64b timestamp by correlating the
32b timestamp with cached_time for performance. The reconstruction
algorithm does both forward & backward interpolation.
The 32b timeval has overflow duration of 2^32 counts ~= 4.23 second.
Due to interpolation in both direction, its now ~= 2.125 second
IIRC, going with at least half a duration, the cached_time is updated
with periodic thread of 1 second (worst-case) periodicity.
But the 1 second periodicity is based on System-timer.
With PPB adjustments, if the 1588 timers increments at say
double the rate, (2s in-place of 1s), the Nyquist rate/half duration
sampling/update of cached_time with 1 second periodic thread will
lead to incorrect interpolations.
Hence we should restrict the PPB adjustments to at least half duration
of cached_time update which translates to 500,000,000 PPB.
Since the periodicity of the cached-time system thread can vary,
it is good to have some buffer time and considering practicality of
PPB adjustments, limiting the max_adj to 100,000,000.
Signed-off-by: Siddaraju DH <siddaraju.dh@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 323d91d468 ]
ath11k fails to load if there are multiple ath11k PCI devices with same name:
ath11k_pci 0000:01:00.0: Hardware name qcn9074 hw1.0
debugfs: Directory 'ath11k' with parent '/' already present!
ath11k_pci 0000:01:00.0: failed to create ath11k debugfs
ath11k_pci 0000:01:00.0: failed to create soc core: -17
ath11k_pci 0000:01:00.0: failed to init core: -17
ath11k_pci: probe of 0000:01:00.0 failed with error -17
Fix this by creating a directory for each ath11k device using schema
<bus>-<devname>, for example "pci-0000:06:00.0". This directory created under
the top-level ath11k directory, for example /sys/kernel/debug/ath11k.
The reference to the toplevel ath11k directory is not stored anymore within ath11k, instead
it's retrieved using debugfs_lookup(). If the directory does not exist it will
be created. After the last directory from the ath11k directory is removed, for
example when doing rmmod ath11k, the empty ath11k directory is left in place,
it's a minor cosmetic issue anyway.
Here's an example hierarchy with one WCN6855:
ath11k
`-- pci-0000:06:00.0
|-- mac0
| |-- dfs_block_radar_events
| |-- dfs_simulate_radar
| |-- ext_rx_stats
| |-- ext_tx_stats
| |-- fw_dbglog_config
| |-- fw_stats
| | |-- beacon_stats
| | |-- pdev_stats
| | `-- vdev_stats
| |-- htt_stats
| |-- htt_stats_reset
| |-- htt_stats_type
| `-- pktlog_filter
|-- simulate_fw_crash
`-- soc_dp_stats
I didn't have a test setup where I could connect multiple ath11k devices to the
same the host, so I have only tested this with one device.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221220121231.20120-1-kvalo@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8f185e39b ]
The call "skb_copy_from_linear_data(skb, inl + 1, spc)" triggers a FORTIFY
memcpy() warning on ppc64 platform:
In function ‘fortify_memcpy_chk’,
inlined from ‘skb_copy_from_linear_data’ at ./include/linux/skbuff.h:4029:2,
inlined from ‘build_inline_wqe’ at drivers/net/ethernet/mellanox/mlx4/en_tx.c:722:4,
inlined from ‘mlx4_en_xmit’ at drivers/net/ethernet/mellanox/mlx4/en_tx.c:1066:3:
./include/linux/fortify-string.h:513:25: error: call to ‘__write_overflow_field’ declared with
attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()?
[-Werror=attribute-warning]
513 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Same behaviour on x86 you can get if you use "__always_inline" instead of
"inline" for skb_copy_from_linear_data() in skbuff.h
The call here copies data into inlined tx destricptor, which has 104
bytes (MAX_INLINE) space for data payload. In this case "spc" is known
in compile-time but the destination is used with hidden knowledge
(real structure of destination is different from that the compiler
can see). That cause the fortify warning because compiler can check
bounds, but the real bounds are different. "spc" can't be bigger than
64 bytes (MLX4_INLINE_ALIGN), so the data can always fit into inlined
tx descriptor. The fact that "inl" points into inlined tx descriptor is
determined earlier in mlx4_en_xmit().
Avoid confusing the compiler with "inl + 1" constructions to get to past
the inl header by introducing a flexible array "data" to the struct so
that the compiler can see that we are not dealing with an array of inl
structs, but rather, arbitrary data following the structure. There are
no changes to the structure layout reported by pahole, and the resulting
machine code is actually smaller.
Reported-by: Josef Oskera <joskera@redhat.com>
Link: https://lore.kernel.org/lkml/20230217094541.2362873-1-joskera@redhat.com
Fixes: f68f2ff915 ("fortify: Detect struct member overflows in memcpy() at compile-time")
Cc: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20230218183842.never.954-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7515af9fb ]
When the bcmgenet_mii_config() code was refactored it was missed
that the LED control for the MoCA interface got overwritten by
the port_ctrl value. Its previous programming is restored here.
Fixes: 4f8d81b77e ("net: bcmgenet: Refactor register access in bcmgenet_mii_config")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9684b000a8 ]
Start a rework initiated by Vincents remarks "You should not report
the greatest of txerr and rxerr but the one which actually increased."
[1] and "As far as I understand, those flags should be set only when
the threshold is reached" [2] .
Therefore make use of can_change_state() to (among others) set the
flags CAN_ERR_CRTL_[RT]X_WARNING and CAN_ERR_CRTL_[RT]X_PASSIVE,
maintain CAN statistic counters for error_warning, error_passive and
bus_off.
Relocate testing alloc_can_err_skb() for NULL to the end of
esd_usb_rx_event(), to have things like can_bus_off(),
can_change_state() working even in out of memory conditions.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: [1] https://lore.kernel.org/all/CAMZ6RqKGBWe15aMkf8-QLf-cOQg99GQBebSm+1wEzTqHgvmNuw@mail.gmail.com/
Link: [2] https://lore.kernel.org/all/CAMZ6Rq+QBO1yTX_o6GV0yhdBj-RzZSRGWDZBS0fs7zbSTy4hmA@mail.gmail.com/
Link: https://lore.kernel.org/all/20230216190450.3901254-3-frank.jungclaus@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 118469f881 ]
Move the supply for cf->data[3] (bit stream position of CAN error), in
case of a bus- or protocol-error, outside of the "switch (ecc &
SJA1000_ECC_MASK){}"-statement, because this bit stream position is
independent of the error type.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: https://lore.kernel.org/all/20230216190450.3901254-2-frank.jungclaus@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cfb7df24c ]
This code re-uses "i" to be the iterator for both the inside and outside
loops. It means the outside loop will exit earlier than intended.
Fixes: d219b7eb37 ("mwifiex: handle BT coex event to adjust Rx BA window size")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/Y+ERnaDaZD7RtLvX@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26e6775f75 ]
Add the check for the return value of the create_singlethread_workqueue()
in order to avoid NULL pointer dereference.
Fixes: b481de9ca0 ("[IWLWIFI]: add iwlwifi wireless drivers")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230209010748.45454-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fdeb8b9f2 ]
Add the check for the return value of the create_singlethread_workqueue
in order to avoid NULL pointer dereference.
Fixes: b481de9ca0 ("[IWLWIFI]: add iwlwifi wireless drivers")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230208063032.42763-2-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
