[ Upstream commit a4a3203426 ]
The order in which clocks are stopped matters as some of the clock
like NPL are derived from MCLK.
Without this patch, Dragonboard RB5 DSP would crash with below error:
qcom_q6v5_pas 17300000.remoteproc: fatal error received:
ABT_dal.c:278:ABTimeout: AHB Bus hang is detected,
Number of bus hang detected := 2 , addr0 = 0x3370000 , addr1 = 0x0!!!
Turn off fsgen first, followed by npl and then finally mclk, which is exactly
the opposite order of enable sequence.
Fixes: 1dc3459009 ("ASoC: codecs: lpass: register mclk after runtime pm")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Link: https://lore.kernel.org/r/20230323110125.23790-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5e7e398f6 ]
When we run syzkaller we get below Out of Bound.
"KASAN: slab-out-of-bounds Read in regcache_flat_read"
Below is the backtrace of the issue:
dump_backtrace+0x0/0x4c8
show_stack+0x34/0x44
dump_stack_lvl+0xd8/0x118
print_address_description+0x30/0x2d8
kasan_report+0x158/0x198
__asan_report_load4_noabort+0x44/0x50
regcache_flat_read+0x10c/0x110
regcache_read+0xf4/0x180
_regmap_read+0xc4/0x278
_regmap_update_bits+0x130/0x290
regmap_update_bits_base+0xc0/0x15c
snd_soc_component_update_bits+0xa8/0x22c
snd_soc_component_write_field+0x68/0xd4
tx_macro_digital_mute+0xec/0x140
Actually There is no need to have decimator with 32 bits.
By limiting the variable with short type u8 issue is resolved.
Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr@quicinc.com>
Link: https://lore.kernel.org/r/20230304080702.609-1-quic_visr@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0de2cc3707 ]
Without gpiolib, this driver fails to link:
arm-linux-gnueabi-ld: sound/soc/codecs/zl38060.o: in function `chip_gpio_get':
zl38060.c:(.text+0x30): undefined reference to `gpiochip_get_data'
arm-linux-gnueabi-ld: sound/soc/codecs/zl38060.o: in function `zl38_spi_probe':
zl38060.c:(.text+0xa18): undefined reference to `devm_gpiochip_add_data_with_key'
This appears to have been in the driver since the start, but is hard to
hit in randconfig testing since gpiolib is almost always selected by something
else.
Fixes: 52e8a94baf ("ASoC: Add initial ZL38060 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230227085850.2503725-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5bfa7277e ]
The regulators are supposed to be controlled through the
set_bias_level() component callback. Moreover, the regulators are not
enabled during probe and so, this would lead to a regulator unbalanced
use count.
Fixes: ca514c0f12 ("ASOC: Add ADAU7118 8 Channel PDM-to-I2S/TDM Converter driver")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230224104551.1139981-1-nuno.sa@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 771725efe5 ]
When the 'ti,gpio-config' property is not defined, the
device_property_count_u32() will return an error, rather than zero.
The current check, only handles a return value of zero, which assumes that
the property is defined and has nothing defined.
This change extends the check to also check for an error case (most likely
to be hit by the case that the 'ti,gpio-config' is not defined).
In case that the 'ti,gpio-config' and the returned 'gpio_count' is not
correct, there is a 'if (gpio_count != ADCX140_NUM_GPIO_CFGS)' check, a few
lines lower that will return -EINVAL.
This means that someone tried to define 'ti,gpio-config', but with the
wrong number of GPIOs.
Fixes: d521432149 ("ASoC: tlv320adcx140: Add support for configuring GPIO pin")
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230213073805.14640-1-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e762143437 ]
For some reason we ended up with incorrect mclk rate which should be
1920000 instead of 96000, So far we were getting lucky as the same clk
is set to 192000 by wsa and va macro. This issue is discovered when there
is no wsa macro active and only rx or tx path is tested.
Fix this by setting correct rate.
Fixes: c39667ddcf ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Fixes: af3d54b997 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-7-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe1e7e8ce2 ]
Seems like properties parsing and reading was copy-pasted,
so "everest,interrupt-src" and "everest,interrupt-clk" are saved into
the es8326->jack_pol variable. This might lead to wrong settings
being saved into the reg 57 (ES8326_HP_DET).
Fix this by using proper variables while reading properties.
Signed-off-by: Alexey Firago <a.firago@yadro.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com
Link: https://lore.kernel.org/r/20230204195106.46539-1-a.firago@yadro.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2036890282 ]
Modify clock_stop_timeout value for rt715-sdca according to
the requirement of internal clock trimming.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://lore.kernel.org/r/574b6586267a458cac78c5ac4d5b10bd@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e18c6da62e ]
While looking through legacy platform data users, I noticed that
the DT probing never uses data from the DT properties, as the
platform_data structure gets overwritten directly after it
is initialized.
There have never been any boards defining the platform_data in
the mainline kernel either, so this driver so far only worked
with patched kernels or with the default values.
For the benefit of possible downstream users, fix the DT probe
by no longer overwriting the data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230126162203.2986339-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0576cd642 ]
In tas5805m_refresh, we switch pages to update the DSP volume control,
but we need to switch back to page 0 before trying to alter the
soft-mute control. This latter page-switch was missing.
Fixes: ec45268467 ("ASoC: add support for TAS5805M digital amplifier")
Signed-off-by: Daniel Beer <daniel.beer@igorinstitute.com>
Link: https://lore.kernel.org/r/1fea38a71ea6ab0225d19ab28d1fa12828d762d0.1675497326.git.daniel.beer@igorinstitute.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1473237926 ]
There's some setup we need to do in order to get the DSP initialized,
and this can't be done until a bit-clock is ready. In an earlier version
of this driver, this work was done in a DAPM callback.
The DAPM callback doesn't guarantee that the bit-clock is running, so
the work was moved instead to the trigger callback. Unfortunately this
callback runs in atomic context, and the setup code needs to do I2C
transactions.
Here we use a work_struct to kick off the setup in a thread instead.
Fixes: ec45268467 ("ASoC: add support for TAS5805M digital amplifier")
Signed-off-by: Daniel Beer <daniel.beer@igorinstitute.com>
Link: https://lore.kernel.org/r/85d8ba405cb009a7a3249b556dc8f3bdb1754fdf.1675497326.git.daniel.beer@igorinstitute.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 262b42e02d ]
I'm not exactly clear on what strange workflow causes people to do it,
but clearly occasionally some files end up being committed as executable
even though they clearly aren't.
This is a reprise of commit 90fda63fa1 ("treewide: fix up files
incorrectly marked executable"), just with a different set of files (but
with the same trivial shell scripting).
So apparently we need to re-do this every five years or so, and Joe
needs to just keep reminding me to do so ;)
Reported-by: Joe Perches <joe@perches.com>
Fixes: 523375c943 ("drm/vmwgfx: Port vmwgfx to arm64")
Fixes: 5c43993777 ("ASoC: codecs: add support for ES8326")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 472a6309c6 ]
Restore volume after charge pump and PGA activation to ensure
that volume settings are correctly applied when re-enabling codec
from SND_SOC_BIAS_OFF state.
CLASS_W, CHARGE_PUMP and POWER_MANAGEMENT_2 register configuration
affect how the volume register are applied and must be configured first.
Fixes: a91eb199e4 ("ASoC: Initial WM8904 CODEC driver")
Link: https://lore.kernel.org/all/c7864c35-738c-a867-a6a6-ddf9f98df7e7@gmail.com/
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221223080247.7258-1-francesco@dolcini.it
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7161bd540e upstream.
RT9120 uses PM runtime autosuspend to decrease the frequently on/off
spent time. This exists one case, when pcm is closed and dev PM is
waiting for autosuspend time expired to enter runtime suspend state.
At the mean time, system is going to enter suspend, dev PM runtime
suspend won't be called. It makes the rt9120 suspend consumption
current not as expected.
This patch can fix the rt9120 dev PM issue during runtime autosuspend
and system suspend by binding dev PM runtime and ASoC component PM.
Fixes: 80b949f332 ("ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1672301033-3675-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c900dcc3f ]
For some reason rt5670_i2c_probe() does a pm_runtime_put() at the end
of a successful probe. But it has never done a pm_runtime_get() leading
to the following error being logged into dmesg:
rt5670 i2c-10EC5640:00: Runtime PM usage count underflow!
Fix this by removing the unnecessary pm_runtime_put().
Fixes: 64e89e5f55 ("ASoC: rt5670: Add runtime PM support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221213123319.11285-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9529dc167f ]
Fix this by dropping wm8994->accdet_lock while calling
cancel_delayed_work_sync(&wm8994->mic_work) in wm1811_jackdet_irq().
Fixes: c0cc3f1665 ("ASoC: wm8994: Allow a delay between jack insertion and microphone detect")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221209091657.1183-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 953dbd1cef ]
KBL-R RVP platforms also use combojack, so we need to enable that
configuration for them.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221010121955.718168-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97b801be6f ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by going to
err_pm instead of err_clk.
Fixes:f086ba9d5389c ("ASoC: pcm512x: Support mastering BCLK/LRCLK using the PLL")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220928160402.126140-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f52ceddc4 ]
Fix build errors when GPIOLIB is not set/enabled:
../sound/soc/codecs/wsa883x.c: In function 'wsa883x_probe':
../sound/soc/codecs/wsa883x.c:1394:25: error: implicit declaration of function 'devm_gpiod_get_optional'; did you mean 'devm_regulator_get_optional'? [-Werror=implicit-function-declaration]
wsa883x->sd_n = devm_gpiod_get_optional(&pdev->dev, "powerdown",
../sound/soc/codecs/wsa883x.c:1395:49: error: 'GPIOD_FLAGS_BIT_NONEXCLUSIVE' undeclared (first use in this function)
GPIOD_FLAGS_BIT_NONEXCLUSIVE);
../sound/soc/codecs/wsa883x.c:1414:9: error: implicit declaration of function 'gpiod_direction_output'; did you mean 'gpio_direction_output'? [-Werror=implicit-function-declaration]
gpiod_direction_output(wsa883x->sd_n, 1);
Fixes: 43b8c7dc85 ("ASoC: codecs: add wsa883x amplifier support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Banajit Goswami <bgoswami@quicinc.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221108001829.5100-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5dba73f7 ]
The shutdown GPIO is active low (SD_N), but this depends on actual board
layout. Linux drivers should only care about logical state, where high
(1) means shutdown and low (0) means do not shutdown.
Invert the GPIO to match logical value.
Fixes: 43b8c7dc85 ("ASoC: codecs: add wsa883x amplifier support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221110133512.478831-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The table in the datasheet actually shows the volume values in the wrong
order, with the two -3dB values being reversed. This appears to have
caused the lower of the two values to be used in the driver when the
higher should have been, correct this mixup.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221125162348.1288005-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the devm_kcalloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference.
Fixes: 349dd23931 ("ASoC: max98373: don't access volatile registers in bias level off")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20221116082508.17418-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the hardware behavior, it takes some time for CBJ detection/impedance sensing/de-bounce.
The ClockStop_NotFinished flag will be raised until these functions are completed.
In ClockStopMode0 mode case, the SdW controller might check this flag from D3 to D0 when the
jack detection interrupt happened.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221116090318.5017-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit bf2aebccdd ("ASoC: sgtl5000: Fix noise on shutdown/remove"),
the device power control registers are reset when the driver is
removed/shutdown.
This is an issue when the device is configured to use the PLL clock. The
device will stop responding if it is still configured to use the PLL
clock but the PLL clock is powered down.
When rebooting linux, the probe function will show:
sgtl5000 0-000a: Error reading chip id -11
Make sure that the CHIP_CLK_CTRL is reset to its default value before
powering down the device.
Fixes: bf2aebccdd ("ASoC: sgtl5000: Fix noise on shutdown/remove")
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20221110190612.1341469-1-detlev.casanova@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
correct frequency of LRCLK and BCLK. Sometimes the read-only value
can't be updated timely after enabling SYSCLK. This results in wrong
calculation values. Delay is introduced here to wait for newest value
from register. The time of the delay should be at least 500~1000us
according to test.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109121354.123958-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Starting with 6.0-rc1 the CPU DAI is not registered and the sound
card is unavailable. Adding legacy_dai_naming causes it to function
properly again.
Fixes: fc34ece41f ("ASoC: Refactor non_legacy_dai_naming flag")
Signed-off-by: Jason Montleon <jmontleo@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221103144612.4431-2-jmontleo@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Starting with 6.0-rc1 these messages are logged and the sound card
is unavailable. Adding legacy_dai_naming to the rt5514-spi causes
it to function properly again.
[ 16.928454] kbl_r5514_5663_max kbl_r5514_5663_max: ASoC: CPU DAI
spi-PRP0001:00 not registered
[ 16.928561] platform kbl_r5514_5663_max: deferred probe pending
Fixes: fc34ece41f ("ASoC: Refactor non_legacy_dai_naming flag")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216641
Signed-off-by: Jason Montleon <jmontleo@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221103144612.4431-1-jmontleo@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: eae9f9ce18 ("ASoC: add tas2780 driver")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Siarhei Volkau <lis8215@gmail.com>:
The patchset fixes:
- Line In path stays powered off during capturing or
bypass to mixer.
- incorrectly represented dB values in alsamixer, et al.
- incorrect represented Capture input selector in alsamixer
in Playback tab.
- wrong control selected as Capture Master
There are two spelling mistakes in codec routing description. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221019071639.1003730-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates the pad control and checks the
hardware version to set the different preset settings.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221019095731.31101-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If CONFIG_SND_SOC_TLV320ADC3XXX=y:
`.exit.text' referenced in section `.data' of sound/soc/codecs/tlv320adc3xxx.o: defined in discarded section `.exit.text' of sound/soc/codecs/tlv320adc3xxx.o
Fix this by wrapping the adc3xxx_i2c_remove() pointer in __exit_p().
Fixes: e9a3b57efd ("ASoC: codec: tlv320adc3xxx: New codec driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/3225ba4cfe558d9380155e75385954dd21d4e7eb.1665909132.git.geert@linux-m68k.org
Signed-off-by: Mark Brown <broonie@kernel.org>
At the moment Capture source selector appears on Playback
tab in the alsamixer and has a senseless name.
Let's fix that.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-5-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Line In Bypass control is used as Master Capture at the moment
this is completely incorrect.
Current control routed to Mixer instead of ADC, thus can't affect
Capture path. ADC control shall be used instead.
ADC volume control parameters are different, so the patch fixes that
as well. Manual says (16.6.3.2 Programmable input attenuation amplifier:
PGATM) that gain varies in range 0dB..22.5dB with 1.5dB step.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-4-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DAC volume control is the Master Playback Volume at the moment
and it reports wrong levels in alsamixer and other alsa apps.
The patch fixes that, as stated in manual on the jz4725b SoC
(16.6.3.4 Programmable attenuation: GOD) the ctl range varies
from -22.5dB to 0dB with 1.5dB step.
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221016132648.3011729-3-lis8215@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In wm8962 driver, the WM8962_ADDITIONAL_CONTROL_4 is used as a volatile
register, but this register mixes a bunch of volatile status bits and a
bunch of non-volatile control bits. The dapm widgets TEMP_HP and
TEMP_SPK leverages the control bits in this register. After the wm8962
probe, the regmap will bet set to cache only mode, then a read error
like below would be triggered when trying to read the initial power
state of the dapm widgets TEMP_HP and TEMP_SPK.
wm8962 0-001a: ASoC: error at soc_component_read_no_lock
on wm8962.0-001a: -16
In order to fix this issue, we add event handler to actually power
up/down these widgets. With this change, we also need to explicitly
power off these widgets in the wm8962 probe since they are enabled
by default.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Tested-by: Adam Ford <aford173@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221010092014.2229246-1-xiaolei.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Zhang Qilong <zhangqilong3@huawei.com>:
Both the old and new patch have been applied, it will resulted in
redundant calling of pm_runtime_disable when error returns. We Just
revert the old three patches to fix it.
It would be better to keep the pm_runtime enables before the
IRQ and component stuff. Both of those could start triggering
PM runtime events.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221008140522.134912-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
