commit 06f66261a1 upstream.
At least restoring the MST topology during system resume needs to use
AUX before the display HW readout->sanitization sequence is complete,
but on TC ports the PHY may be in the wrong mode for this, resulting in
the AUX transfers to fail.
The initial TC port mode is kept fixed as BIOS left it for the above HW
readout sequence (to prevent changing the mode on an enabled port). If
the port is disabled this initial mode is TBT - as in any case the PHY
ownership is not held - even if a DP-alt sink is connected. Thus, the
AUX transfers during this time will use TBT mode instead of the expected
DP-alt mode and so time out.
Fix the above by connecting the PHY during port initialization if the
port is disabled, which will switch to the expected mode (DP-alt in the
above case).
As the encoder/pipe HW state isn't read-out yet at this point, check if
the port is enabled based on the DDI_BUF enabled flag. Save the read-out
initial mode, so intel_tc_port_sanitize_mode() can check this wrt. the
read-out encoder HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-5-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67165722c2 upstream.
An enabled TC MST port holds one TC port link reference, regardless of
the number of enabled streams on it, but the TC port HW readout takes
one reference for each active MST stream.
Fix the HW readout, taking only one reference for MST ports.
This didn't cause an actual problem, since the encoder HW readout doesn't
yet support reading out the MST HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-3-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a82796a2e3 upstream.
During system resume DP MST requires AUX to be working already before
the HW state readout of the given encoder. Since AUX requires the
encoder/PHY TypeC mode to be initialized, which atm only happens during
HW state readout, these AUX transfers can change the TypeC mode
incorrectly (disconnecting the PHY for an enabled encoder) and trigger
the state check WARNs in intel_tc_port_sanitize().
Fix this by initializing the TypeC mode earlier both during driver
loading and system resume and making sure that the mode can't change
until the encoder's state is read out. While at it add the missing
DocBook comments and rename
intel_tc_port_sanitize()->intel_tc_port_sanitize_mode() for consistency.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922172148.2913088-1-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5c6d52ff4b ]
If the securedisplay TA failed to load the first time, it's unlikely
to work again after a suspend/resume cycle or reset cycle and it appears
to be causing problems in futher attempts.
Fixes: e42dfa66d5 ("drm/amdgpu: Add secure display TA load for Renoir")
Reported-by: Filip Hejsek <filip.hejsek@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2633
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 570b295248 ]
Since adding gang submit we need to take the gang size into account
while reserving fences.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 4624459c84 ("drm/amdgpu: add gang submit frontend v6")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e49de73fb ]
The scenario being fixed here is depicted in the following sequence-
modprobe i915
echo 1 > /sys/class/drm/card0/gt/gt0/slpc_ignore_eff_freq
echo 300 > /sys/class/drm/card0/gt_min_freq_mhz (RPn)
cat /sys/class/drm/card0/gt_cur_freq_mhz --> cur == RPn as expected
echo 1 > /sys/kernel/debug/dri/0/gt0/reset --> reset
cat /sys/class/drm/card0/gt_min_freq_mhz --> cached freq is RPn
cat /sys/class/drm/card0/gt_cur_freq_mhz --> it's not RPn, but RPe!!
When SLPC reinitializes, it sets SLPC min freq to efficient frequency.
Even if we disable efficient freq post that, we should restore the cached
min freq (via H2G) for it to take effect.
v2: Clarify commit message (Ashutosh)
Fixes: 95ccf312a1 ("drm/i915/guc/slpc: Allow SLPC to use efficient frequency")
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230621014257.1769564-1-vinay.belgaumkar@intel.com
(cherry picked from commit da86b2b13f)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5311892a0a ]
Encoder compute config is changing hw.adjusted mode. Uapi.adjusted mode
doesn't get updated before psr compute config gets called. This causes io
and fast wake line calculation using adjusted mode containing values before
encoder adjustments. Fix this by using hw.adjusted mode instead of
uapi.adjusted mode.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8475
Fixes: cb42e8ede5 ("drm/i915/psr: Use calculated io and fast wake lines")
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230620111745.2870706-1-jouni.hogander@intel.com
(cherry picked from commit ef0af9db2a)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d6149086b4 upstream.
This change causes regression when eDP and external display in mirror
mode. When external display supports low resolution than eDP, use eDP
timing to driver external display may cause corruption on external
display.
This reverts commit e749dd10e5.
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2655
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71344a718a ]
The fixed commit listed in the Fixes tag below, introduced a bug in
amdgpu_ras.c::amdgpu_reserve_page_direct(), in that when introducing the new
amdgpu_umc_fill_error_record() and internally in that new function the physical
address (argument "uint64_t retired_page"--wrong name) is right-shifted by
AMDGPU_GPU_PAGE_SHIFT. Thus, in amdgpu_reserve_page_direct() when we pass
"address" to that new function, we should NOT right-shift it, since this
results, erroneously, in the page address to be 0 for first
2^(2*AMDGPU_GPU_PAGE_SHIFT) memory addresses.
This commit fixes this bug.
Cc: Tao Zhou <tao.zhou1@amd.com>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Fixes: 400013b268 ("drm/amdgpu: add umc_fill_error_record to make code more simple")
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Link: https://lore.kernel.org/r/20230610113536.10621-1-luben.tuikov@amd.com
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d50dc746ff ]
Fixes the following gcc with W=1:
In file included from ./include/linux/string.h:253,
from ./include/linux/bitmap.h:11,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/cpumask.h:5,
from ./arch/x86/include/asm/msr.h:11,
from ./arch/x86/include/asm/processor.h:22,
from ./arch/x86/include/asm/cpufeature.h:5,
from ./arch/x86/include/asm/thread_info.h:53,
from ./include/linux/thread_info.h:60,
from ./arch/x86/include/asm/preempt.h:7,
from ./include/linux/preempt.h:78,
from ./include/linux/spinlock.h:56,
from ./include/linux/mmzone.h:8,
from ./include/linux/gfp.h:7,
from ./include/linux/firmware.h:7,
from drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu11/sienna_cichlid_ppt.c:26:
In function ‘fortify_memcpy_chk’,
inlined from ‘sienna_cichlid_append_powerplay_table’ at drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu11/sienna_cichlid_ppt.c:444:2,
inlined from ‘sienna_cichlid_setup_pptable’ at drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu11/sienna_cichlid_ppt.c:506:8,
inlined from ‘sienna_cichlid_setup_pptable’ at drivers/gpu/drm/amd/amdgpu/../pm/swsmu/smu11/sienna_cichlid_ppt.c:494:12:
./include/linux/fortify-string.h:413:4: warning: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
413 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
the compiler complains about the size calculation in the memcpy() -
"sizeof(*smc_dpm_table) - sizeof(smc_dpm_table->table_header)" is much
larger than what fits into table_member.
Hence, reuse 'smu_memcpy_trailing' for nv1x
Fixes: 7077b19a38 ("drm/amd/pm: use macro to get pptable members")
Suggested-by: Evan Quan <Evan.Quan@amd.com>
Cc: Evan Quan <Evan.Quan@amd.com>
Cc: Chengming Gui <Jack.Gui@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa0048a4b1 ]
The DP component's unbind operation walks through the submodules to
unregister and clean things up. But if the unbind happens because the DP
controller itself is being removed, all the memory for those submodules
has just been freed.
Change the order of these operations to avoid the many use-after-free
that otherwise happens in this code path.
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542166/
Link: https://lore.kernel.org/r/20230612220259.1884381-1-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 155fa3a91d ]
Currently, slice_count is being used to calculate word count and
pkt_per_line. Instead, these values should be calculated using slice per
packet, which is not the same as slice_count.
Slice count represents the number of slices per interface, and its value
will not always match that of slice per packet. For example, it is possible
to have cases where there are multiple slices per interface but the panel
specifies only one slice per packet.
Thus, use the default value of one slice per packet and remove slice_count
from the aforementioned calculations.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Fixes: bc6b6ff813 ("drm/msm/dsi: Use DSC slice(s) packet size to compute word count")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/541965/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-5-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82e72fd22a ]
According to downstream /and the comment copied from it/ this comparison
should be the other way around. In other words, when the panel driver
requests to use more slices per packet than what could be sent over this
interface, it is bumped down to only use a single slice per packet (and
strangely not the number of slices that could fit on the interface).
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/515686/
Link: https://lore.kernel.org/r/20221221231943.1961117-4-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Stable-dep-of: 155fa3a91d ("drm/msm/dsi: Remove incorrect references to slice_count")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc6b6ff813 ]
According to downstream the value to use for WORD_COUNT is
bytes_per_pkt, which denotes the number of bytes in a packet based on
how many slices have been configured by the panel driver times the
width of a slice times the number of bytes per pixel.
The DSC panels seen thus far use one byte per pixel, only one slice
per packet, and a slice width of half the panel width leading to the
desired bytes_per_pkt+1 value to be equal to hdisplay/2+1. This however
isn't the case anymore for panels that configure two slices per packet,
where the value should now be hdisplay+1.
Note that the aforementioned panel (on a Sony Xperia XZ3, sdm845) with
slice_count=1 has also been tested to successfully accept slice_count=2,
which would have shown corrupted output previously.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/515694/
Link: https://lore.kernel.org/r/20221221231943.1961117-3-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Stable-dep-of: 155fa3a91d ("drm/msm/dsi: Remove incorrect references to slice_count")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bcfc7b904 ]
We can not support color management without DSPP blocks being provided
in the HW catalog. Do not enable color management for CRTCs if num_dspps
is 0.
Fixes: 4259ff7ae5 ("drm/msm/dpu: add support for pcc color block in dpu driver")
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Tested-by: Yongqin Liu <yongqin.liu@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542141/
Link: https://lore.kernel.org/r/20230612182534.3345805-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 736a932736 ]
The commit 010c8bbad2 ("drm: msm: adreno: Disable preemption on Adreno
510") added special handling for a510 (this SKU doesn't seem to support
preemption, so the driver should clamp nr_rings to 1). However the
gpu->revn is not yet set (it is set later, in adreno_gpu_init()) and
thus the condition is always false. Check config->rev instead.
Fixes: 010c8bbad2 ("drm: msm: adreno: Disable preemption on Adreno 510")
Reported-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Adam Skladowski <a39.skl@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/531511/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f0bcf49e9 ]
This is motivated by OOB access in amdgpu_vm_update_range when
offset_in_bo+map_size overflows.
v2: keep the validations in amdgpu_vm_bo_map
v3: add the validations to amdgpu_vm_bo_map/amdgpu_vm_bo_replace_map
rather than to amdgpu_gem_va_ioctl
Fixes: 9f7eb5367d ("drm/amdgpu: actually use the VM map parameters")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1becc57cd1 ]
Function rv740_get_decoded_reference_divider() may return 0 due to
unpredictable reference divider value calculated in
radeon_atom_get_clock_dividers(). This will lead to
division-by-zero error once that value is used as a divider
in calculating 'clk_s'.
While unlikely, this issue should nonetheless be prevented so add a
sanity check for such cases by testing 'decoded_ref' value against 0.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
v2: minor coding style fixes (Alex)
In practice this should actually happen as the vbios should be
properly populated.
Fixes: 66229b2005 ("drm/radeon/kms: add dpm support for rv7xx (v4)")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b18f05a066 ]
[Why]
When freesync video mode is enabled, switching resolution from native
mode to one of the freesync video compatible modes can trigger continous
artifacts on some eDP panels when running under KDE. The articating can be seen in the
attached bug report.
[How]
Fix this by restricting updates that require full commit by using the same checks
for stream and scaling changes in the the enable pass of dm_update_crtc_state()
along with the check for compatible timings for freesync vide mode.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2162
Fixes: da5e149097 ("drm/amd/display: Fix hang when skipping modeset")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cabbdea1f1 ]
Pointer mqd_mem_obj can be deallocated in kfd_gtt_sa_allocate().
The function then returns non-zero value, which causes the second deallocation.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d1f8f0d17d ("drm/amdkfd: Move non-sdma mqd allocation out of init_mqd")
Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bafc31166a ]
It is likely p1_min_meta_chunk_bytes was expected here, instead of
min_meta_chunk_bytes.
Test the correct variable.
Fixes: dda4fb85e4 ("drm/amd/display: DML changes for DCN32/321")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 960e27a574 ]
It is likely Height was expected here, instead of Width.
Test the correct variable.
Fixes: 17529ea2ac ("drm/amd/display: Optimizations for DML math")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12cef323c9 ]
The CTL_FLUSH register should be programmed with the 22th bit
(DSC_IDX) to flush the DSC hardware blocks, not the literal value of
22 (which corresponds to flushing VIG1, VIG2 and RGB1 instead).
Changes in V12:
-- split this patch out of "separate DSC flush update out of interface"
Changes in V13:
-- rewording the commit text
Changes in V14:
-- drop 'DSC" from "The DSC CTL_FLUSH register" at commit text
Fixes: 77f6da9048 ("drm/msm/disp/dpu1: Add DSC support in hw_ctl")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/539496/
Link: https://lore.kernel.org/r/1685036458-22683-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24b495508 ]
The previous setting was related to the overall dimension and not to the
active display area.
In the "PHYSICAL SPECIFICATIONS" section, the datasheet shows the
following parameters:
----------------------------------------------------------
| Item | Specifications | unit |
----------------------------------------------------------
| Display area | 98.7 (W) x 57.5 (H) | mm |
----------------------------------------------------------
| Overall dimension | 105.5(W) x 67.2(H) x 4.96(D) | mm |
----------------------------------------------------------
Fixes: 966fea78ad ("drm/panel: simple: Add support for Ampire AM-480272H3TMQW-T01H")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: fixed Fixes commit id length]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230516085039.3797303-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd9e329af7 ]
The datasheet describes the following initialization flow including
minimum delay times between each step:
1. DSI data lanes need to be in LP-11 and the clock lane in HS mode
2. toggle EN signal
3. initialize registers
4. enable PLL
5. soft reset
6. enable DSI stream
7. check error status register
To meet this requirement we need to make sure the host bridge's
pre_enable() is called first by using the pre_enable_prev_first
flag.
Furthermore we need to split enable() into pre_enable() which covers
steps 2-5 from above and enable() which covers step 7 and is called
after the host bridge's enable().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: ceb515ba29 ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-3-frieder@fris.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fb912e5e1 ]
DSI sink devices typically want the DSI host powered up and configured
before they are powered up. pre_enable is the place this would normally
happen, but they are called in reverse order from panel/connector towards
the encoder, which is the "wrong" order.
Add a new flag pre_enable_prev_first that any bridge can set
to swap the order of pre_enable (and post_disable) for that and the
immediately previous bridge.
Should the immediately previous bridge also set the
pre_enable_prev_first flag, the previous bridge to that will be called
before either of those which requested pre_enable_prev_first.
eg:
- Panel
- Bridge 1
- Bridge 2 pre_enable_prev_first
- Bridge 3
- Bridge 4 pre_enable_prev_first
- Bridge 5 pre_enable_prev_first
- Bridge 6
- Encoder
Would result in pre_enable's being called as Panel, Bridge 1, Bridge 3,
Bridge 2, Bridge 6, Bridge 5, Bridge 4, Encoder.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20221205173328.1395350-5-dave.stevenson@raspberrypi.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Stable-dep-of: dd9e329af7 ("drm/bridge: ti-sn65dsi83: Fix enable/disable flow to meet spec")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1464e48d69 ]
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=m
CONFIG_BACKLIGHT_PWM=y
and also with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=y
CONFIG_BACKLIGHT_PWM=m
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71450f8c82 ]
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20221118224540.619276-18-uwe@kleine-koenig.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Stable-dep-of: 1464e48d69 ("drm/bridge: anx7625: Prevent endless probe loop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3969eadc8 ]
Recommended way of reading the interface timing gen status is via
status register. Timing gen status register will give a reliable status
of the interface especially during ON/OFF transitions. This support was
added from DPU version 5.0.0.
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/524724/
Link: https://lore.kernel.org/r/1677774797-31063-6-git-send-email-quic_vpolimer@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Stable-dep-of: a7129231ed ("drm/msm/dpu: Set DPU_DATA_HCTL_EN for in INTF_SC7180_MASK")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e0a97f84d ]
If the dispcc uses CLK_OPS_PARENT_ENABLE (e.g. on QCM2290), CCF can try
enabling VCO before the rate has been programmed. This can cause clock
lockups and/or other boot issues. Program the VCO to the minimal PLL
rate if the read rate is 0 Hz.
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reported-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Fixes: f079f6d999 ("drm/msm/dsi: Add PHY/PLL for 8x96")
Patchwork: https://patchwork.freedesktop.org/patch/534813/
Link: https://lore.kernel.org/r/20230501011257.3460103-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab87f558dc ]
Currently, the pixel conversion isn't rounding the fixed-point values
before assigning it to the RGB coefficients, which is causing the IGT
pixel-format tests to fail. So, use the drm_fixp2int_round() fixed-point
helper to round the values when assigning it to the RGB coefficients.
Tested with igt@kms_plane@pixel-format and igt@kms_plane@pixel-format-source-clamping.
[v2]:
* Use drm_fixp2int_round() to fix the pixel conversion instead of
casting the values to s32 (Melissa Wen).
Fixes: 89b03aeaef ("drm/vkms: fix 32bit compilation error by replacing macros")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Arthur Grillo <arthurgrillo@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512104044.65034-2-mcanal@igalia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 322d716a3e ]
Currently, the pixel conversion functions repeat the same loop to
iterate the rows. Instead of repeating the same code for each pixel
format, create a function to wrap the loop and isolate the pixel
conversion functionality.
Suggested-by: Arthur Grillo <arthurgrillo@riseup.net>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Arthur Grillo <arthurgrillo@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230418130525.128733-2-mcanal@igalia.com
Stable-dep-of: ab87f558dc ("drm/vkms: Fix RGB565 pixel conversion")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dee23b2c9e ]
Using current settings causes panel flickering on APQ8074 dragonboard.
Adjust panel settings to follow the vendor-provided mode. This also
enables MIPI_DSI_MODE_VIDEO_SYNC_PULSE, which is also specified by the
vendor dtsi for the mentioned dragonboard.
Fixes: ee01723831 ("drm/panel: Add Sharp LS043T1LE01 MIPI DSI panel")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230507172639.2320934-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 123ee07ba5 ]
Smatch reports:
drivers/gpu/drm/sun4i/sun4i_tcon.c:805 sun4i_tcon_init_clocks() warn:
'tcon->clk' from clk_prepare_enable() not released on lines: 792,801.
In the function sun4i_tcon_init_clocks(), tcon->clk and tcon->sclk0 are
not disabled in the error handling, which affects the release of
these variable. Although sun4i_tcon_bind(), which calls
sun4i_tcon_init_clocks(), use sun4i_tcon_free_clocks to disable the
variables mentioned, but the error handling branch of
sun4i_tcon_init_clocks() ignores the required disable process.
To fix this issue, use the devm_clk_get_enabled to automatically
balance enable and disabled calls. As original implementation use
sun4i_tcon_free_clocks() to disable clk explicitly, we delete the
related calls and error handling that are no longer needed.
Fixes: 9026e0d122 ("drm: Add Allwinner A10 Display Engine support")
Fixes: b14e945bda ("drm/sun4i: tcon: Prepare and enable TCON channel 0 clock at init")
Fixes: 8e92404725 ("drm/sun4i: support TCONs without channel 1")
Fixes: 34d698f6e3 ("drm/sun4i: Add has_channel_0 TCON quirk")
Signed-off-by: XuDong Liu <m202071377@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230430112347.4689-1-m202071377@hust.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bac7842cd1 ]
Correct computation of THS_TRAILCNT register.
This register must be set to a value that ensure that
THS_TRAIL > 60 ns + 4 x UI
and
THS_TRAIL > 8 x UI
and
THS_TRAIL < TEOT
with
TEOT = 105 ns + (12 x UI)
with the actual value of THS_TRAIL being
(1 + THS_TRAILCNT) x ByteClk cycle + ((1 to 2) + 2) xHSBYTECLK cycle +
- (PHY output delay)
with PHY output delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-9-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3666aad818 ]
Correct computation of TXTAGOCNT register.
This register must be set to a value that ensure that the
TTA-GO period = (4 x TLPX)
with the actual value of TTA-GO being
4 x (TXTAGOCNT + 1) x (HSByteClk cycle)
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-8-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77a089328d ]
Correct computation of THS_ZEROCNT register.
This register must be set to a value that ensure that
THS_PREPARE + THS_ZERO > 145ns + 10*UI
with the actual value of (THS_PREPARE + THS_ZERO) being
((1 to 2) + 1 + (TCLK_ZEROCNT + 1) + (3 to 4)) x ByteClk cycle +
+ HSByteClk x (2 + (1 to 2)) + (PHY delay)
with PHY delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-7-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cec5ccef85 ]
Add atomic_get_input_bus_fmts() implementation, tc358768 has a parallel
RGB input interface with the actual bus format depending on the amount
of parallel input data lines.
Without this change when the tc358768 is used with less than 24bit the
color mapping is completely wrong.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230330095941.428122-7-francesco@dolcini.it
Stable-dep-of: ee18698e21 ("drm/bridge: tc358768: fix TCLK_TRAILCNT computation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9cf811374 ]
Correct computation of TCLK_ZEROCNT register.
This register must be set to a value that ensure that
(TCLK-PREPARECNT + TCLK-ZERO) > 300ns
with the actual value of (TCLK-PREPARECNT + TCLK-ZERO) being
(1 to 2) + (TCLK_ZEROCNT + 1)) x HSByteClkCycle + (PHY output delay)
with PHY output delay being about
(2 to 3) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-5-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffd2e4bbea ]
Correctly compute the PLL target frequency, the current formula works
correctly only when the input bus width is 24bit, actually to properly
compute the PLL target frequency what is relevant is the bits-per-pixel
on the DSI link.
No regression expected since the DSI format is currently hard-coded as
MIPI_DSI_FMT_RGB888.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-4-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a4020b4c6 ]
According to Toshiba documentation the PLL input clock after the divider
should be not less than 4MHz, fix the PLL parameters computation
accordingly.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-3-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75a8aeac25 ]
Always enable HS video mode setting the TXMD bit, without this change no
video output is present with DSI sinks that are setting
MIPI_DSI_MODE_LPM flag (tested with LT8912B DSI-HDMI bridge).
Previously the driver was enabling HS mode only when the DSI sink was
not explicitly setting the MIPI_DSI_MODE_LPM, however this is not
correct.
The MIPI_DSI_MODE_LPM is supposed to indicate that the sink is willing
to receive data in low power mode, however clearing the
TC358768_DSI_CONTROL_TXMD bit will make the TC358768 send video in
LP mode that is not the intended behavior.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0be05a75de ]
The address of a data structure member was determined before
a corresponding null pointer check in the implementation of
the function “receive_timing_debugfs_show”.
Thus avoid the risk for undefined behaviour by moving the assignment
for the variable “vid” behind the null pointer check.
This issue was detected by using the Coccinelle software.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://patchwork.freedesktop.org/patch/msgid/fa69384f-1485-142b-c4ee-3df54ac68a89@web.de
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
