[ Upstream commit 855d75cf83 ]
There is a potential delay in notifying Linux USB drivers of downstream
USB bus activity when connecting a high-speed or superSpeed device via the
Microchip USB491x hub. This delay is due to the fixed bInterval value of
12 in the silicon of the Microchip USB491x hub.
Microchip requested to ignore the device descriptor and decrease that
value to 9 as it was too late to modify that in silicon.
This patch speeds up the USB enummeration process that helps to pass
Apple Carplay certifications and improve the User experience when utilizing
the USB device via Microchip Multihost USB491x Hub.
A new hub quirk HUB_QUIRK_REDUCE_FRAME_INTR_BINTERVAL speeds up
the notification process for Microchip USB491x hub by limiting
the maximum bInterval value to 9.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231205181829.127353-2-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6666ea93d2 ]
This patch replaces the hardcoded quirk value in the macro with
BIT().
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231205181829.127353-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 730e12fbec ]
Current EP0 dequeue path will share the same as other EPs. However, there
are some special considerations that need to be made for EP0 transfers:
- EP0 transfers never transition into the started_list
- EP0 only has one active request at a time
In case there is a vendor specific control message for a function over USB
FFS, then there is no guarantee on the timeline which the DATA/STATUS stage
is responded to. While this occurs, any attempt to end transfers on
non-control EPs will end up having the DWC3_EP_DELAY_STOP flag set, and
defer issuing of the end transfer command. If the USB FFS application
decides to timeout the control transfer, or if USB FFS AIO path exits, the
USB FFS driver will issue a call to usb_ep_dequeue() for the ep0 request.
In case of the AIO exit path, the AIO FS blocks until all pending USB
requests utilizing the AIO path is completed. However, since the dequeue
of ep0 req does not happen properly, all non-control EPs with the
DWC3_EP_DELAY_STOP flag set will not be handled, and the AIO exit path will
be stuck waiting for the USB FFS data endpoints to receive a completion
callback.
Fix is to utilize dwc3_ep0_reset_state() in the dequeue API to ensure EP0
is brought back to the SETUP state, and ensures that any deferred end
transfer commands are handled. This also will end any active transfers
on EP0, compared to the previous implementation which directly called
giveback only.
Fixes: fcd2def663 ("usb: dwc3: gadget: Refactor dwc3_gadget_ep_dequeue")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231206201814.32664-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c7af52c76 ]
There is a scenario where DWC3 runtime suspend is blocked due to the
dwc->connected flag still being true while PM usage_count is zero after
DWC3 giveback is completed and the USB gadget session is being terminated.
This leads to a case where nothing schedules a PM runtime idle for the
device.
The exact condition is seen with the following sequence:
1. USB bus reset is issued by the host
2. Shortly after, or concurrently, a USB PD DR SWAP request is received
(sink->source)
3. USB bus reset event handler runs and issues
dwc3_stop_active_transfers(), and pending transfer are stopped
4. DWC3 usage_count decremented to 0, and runtime idle occurs while
dwc->connected == true, returns -EBUSY
5. DWC3 disconnect event seen, dwc->connected set to false due to DR
swap handling
6. No runtime idle after this point
Address this by issuing an asynchronous PM runtime idle call after the
disconnect event is completed, as it modifies the dwc->connected flag,
which is what blocks the initial runtime idle.
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Cc: <stable@vger.kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240103214946.2596-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f40fc0808 ]
Several sequences utilize the same routine for forcing the control endpoint
back into the SETUP phase. This is required, because those operations need
to ensure that EP0 is back in the default state.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230420212759.29429-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 3c7af52c76 ("usb: dwc3: gadget: Queue PM runtime idle on disconnect event")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 017dbfc05c ]
For Gen1 isoc-in transfer, host still send out unexpected ACK after device
finish the burst with a short packet, this will cause an exception on the
connected device, such as, a usb 4k camera.
It can be fixed by setting rxfifo depth less than 4k bytes, prefer to use
3k here, the side-effect is that may cause performance drop about 10%,
including bulk transfer.
Fixes: 926d60ae64 ("usb: xhci-mtk: modify the SOF/ITP interval for mt8195")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20240104061640.7335-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66aad7d8d3 ]
In ACM support for sending breaks to devices is optional.
If a device says that it doenot support sending breaks,
the host must respect that.
Given the number of optional features providing tty operations
for each combination is not practical and errors need to be
returned dynamically if unsupported features are requested.
In case a device does not support break, we want the tty layer
to treat that like it treats drivers that statically cannot
support sending a break. It ignores the inability and does nothing.
This patch uses EOPNOTSUPP to indicate that.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 9e98966c7b ("tty: rework break handling")
Link: https://lore.kernel.org/r/20231207132639.18250-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2dd23cc4d0 upstream.
In mon_bin_vma_fault():
offset = vmf->pgoff << PAGE_SHIFT;
if (offset >= rp->b_size)
return VM_FAULT_SIGBUS;
chunk_idx = offset / CHUNK_SIZE;
pageptr = rp->b_vec[chunk_idx].pg;
The code is executed without holding any lock.
In mon_bin_vma_close():
spin_lock_irqsave(&rp->b_lock, flags);
rp->mmap_active--;
spin_unlock_irqrestore(&rp->b_lock, flags);
In mon_bin_ioctl():
spin_lock_irqsave(&rp->b_lock, flags);
if (rp->mmap_active) {
...
} else {
...
kfree(rp->b_vec);
rp->b_vec = vec;
rp->b_size = size;
...
}
spin_unlock_irqrestore(&rp->b_lock, flags);
Concurrent execution of mon_bin_vma_fault() with mon_bin_vma_close() and
mon_bin_ioctl() could lead to atomicity violations. mon_bin_vma_fault()
accesses rp->b_size and rp->b_vec without locking, risking array
out-of-bounds access or use-after-free bugs due to possible modifications
in mon_bin_ioctl().
This possible bug is found by an experimental static analysis tool
developed by our team, BassCheck[1]. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations. The above
possible bug is reported when our tool analyzes the source code of
Linux 6.2.
To address this issue, it is proposed to add a spin lock pair in
mon_bin_vma_fault() to ensure atomicity. With this patch applied, our tool
never reports the possible bug, with the kernel configuration allyesconfig
for x86_64. Due to the lack of associated hardware, we cannot test the
patch in runtime testing, and just verify it according to the code logic.
[1] https://sites.google.com/view/basscheck/
Fixes: 19e6317d24 ("usb: mon: Fix a deadlock in usbmon between ...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Link: https://lore.kernel.org/r/20240105052412.9377-1-2045gemini@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5962ded777 upstream.
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released is a plug evaluates
against the released altmode's partner instead of the calling altmode, so
change adev in typec_altmode_put_partner to properly refer to the altmode
being released.
Because typec_altmode_set_partner calls get_device() on the port altmode,
add partner_adev that points to the port altmode in typec_put_partner to
call put_device() on. typec_altmode_set_partner is not called for port
altmodes, so add a check in typec_altmode_release to prevent
typec_altmode_put_partner() calls on port altmode release.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: <stable@vger.kernel.org>
Co-developed-by: Christian A. Ehrhardt <lk@c--e.de>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Tested-by: Christian A. Ehrhardt <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240103181754.2492492-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c304109e upstream.
Supposed DMA cross 4k bounder problem should be fixed at DEV_VER_V2, but
still met problem when do ISO transfer if sg enabled.
Data pattern likes below when sg enabled, package size is 1k and mult is 2
[UVC Header(8B) ] [data(3k - 8)] ...
The received data at offset 0xd000 will get 0xc000 data, len 0x70. Error
happen position as below pattern:
0xd000: wrong
0xe000: wrong
0xf000: correct
0x10000: wrong
0x11000: wrong
0x12000: correct
...
To avoid DMA cross 4k bounder at ISO transfer, reduce burst len according
to start DMA address's alignment.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-4-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92f02efa1d upstream.
ISO basic transfer is
ITP(SOF) Package_0 Package_1 ... Package_n
CDNS3 DMA start dma transfer from memmory to internal FIFO when get SOF,
controller will transfer data to usb bus from internal FIFO when get IN
token.
According USB spec defination:
Maximum number of packets = (bMaxBurst + 1) * (Mult + 1)
Internal memory should be the same as (bMaxBurst + 1) * (Mult + 1). DMA
don't fetch data advance when ISO transfer, so only reserve
(bMaxBurst + 1) * (Mult + 1) internal memory for ISO transfer.
Need save Mult and bMaxBurst information and set it into EP_CFG register,
otherwise only 1 package is sent by controller, other package will be
lost.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-3-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b8be5ecff upstream.
When IP version >= DEV_VER_V2, gadget:sg_supported is true. So uvc gadget
function driver will use sg to equeue data, first is 8bytes header, the
second is 1016bytes data.
cdns3_prepare_trb: ep2in: trb 0000000000ac755f, dma buf: 0xbf455000, size: 8, burst: 128 ctrl: 0x00000415 (C=1, T=0, ISP, CHAIN, Normal)
cdns3_prepare_trb: ep2in: trb 00000000a574e693, dma buf: 0xc0200fe0, size: 1016, burst: 128 ctrl: 0x00000405 (C=1, T=0, ISP, Normal)
But cdns3_ep_run_transfer() can't correctly handle this case, which only
support one TRB for ISO transfer.
The controller requires duplicate the TD for each SOF if priv_ep->interval
is not 1. DMA will read data from DDR to internal FIFO when get SOF. Send
data to bus when receive IN token. DMA always refill FIFO when get SOF
regardless host send IN token or not. If host send IN token later, some
frames data will be lost.
Fixed it by below major steps:
1. Calculate numembers of TRB base on sg_nums and priv_ep->interval.
2. Remove CHAIN flags for each end TRB of TD when duplicate TD.
3. The controller requires LINK TRB must be first TRB of TD. When check
there are not enough TRBs lefts, just fill LINK TRB for left TRBs.
.... CHAIN_TRB DATA_TRB, CHAIN_TRB DATA_TRB, LINK_TRB ... LINK_TRB
^End of TRB List
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 128d849074 upstream.
After the chipidea driver introduce extcon for id and vbus, it's able
to wakeup from another irq source, in case the system with extcon ID
cable, wakeup from usb ID cable and device removal, the usb device
disconnect irq may come firstly before the extcon notifier while system
resume, so we will get 2 "wakeup" irq, one for usb device disconnect;
and one for extcon ID cable change(real wakeup event), current driver
treat them as 2 successive wakeup irq so can't handle it correctly, then
finally the usb irq can't be enabled. This patch adds a check to bypass
further usb events before controller resume finished to fix it.
Fixes: 1f874edcb7 ("usb: chipidea: add runtime power management support")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20231228110753.1755756-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afe28cd686 upstream.
This reverts commit e835c0a4e2.
Don't omit soft-reset. During initialization, the driver may need to
perform a soft reset to ensure the phy is ready when the controller
updates the GCTL.PRTCAPDIR or other settings by issuing phy soft-reset.
Many platforms often have access to DCTL register for soft-reset despite
being host-only. If there are actual reported issues from the platforms
that don't expose DCTL registers, then we will need to revisit (perhaps
to teach dwc3 to perform xhci's soft-reset USBCMD.HCRST).
Cc: <stable@vger.kernel.org>
Fixes: e835c0a4e2 ("usb: dwc3: don't reset device side if dwc3 was configured as host-only")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/7668ab11a48f260820825274976eb41fec7f54d1.1703282469.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9d40b215e upstream.
Current implementation blocks the running operations when Plug-out and
Plug-In is performed continuously, process gets stuck in
dwc3_thread_interrupt().
Code Flow:
CPU1
->Gadget_start
->dwc3_interrupt
->dwc3_thread_interrupt
->dwc3_process_event_buf
->dwc3_process_event_entry
->dwc3_endpoint_interrupt
->dwc3_ep0_interrupt
->dwc3_ep0_inspect_setup
->dwc3_ep0_stall_and_restart
By this time if pending_list is not empty, it will get the next request
on the given list and calls dwc3_gadget_giveback which will unmap request
and call its complete() callback to notify upper layers that it has
completed. Currently dwc3_gadget_giveback status is set to -ECONNRESET,
whereas it should be -ESHUTDOWN based on condition if not dwc->connected
is true.
Cc: <stable@vger.kernel.org>
Fixes: d742220b35 ("usb: dwc3: ep0: giveback requests on stall_and_restart")
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20231222094704.20276-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff2b89de47 upstream.
When CONFIG_USB_OTG is not set, mxs_phy_is_otg_host() will always return
false. This behaviour is wrong. Since phy.last_event will always be set
for either host or device mode. Therefore, CONFIG_USB_OTG condition
can be removed.
Fixes: 5eda42aebb ("usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20231228110753.1755756-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7fbcd195e2 ]
Here "temp" is the number of characters that we have written and "size"
is the size of the buffer. The intent was clearly to say that if we have
written to the end of the buffer then stop.
However, for that to work the comparison should have been done on the
original "size" value instead of the "size -= temp" value. Not only
will that not trigger when we want to, but there is a small chance that
it will trigger incorrectly before we want it to and we break from the
loop slightly earlier than intended.
This code was recently changed from using snprintf() to scnprintf(). With
snprintf() we likely would have continued looping and passed a negative
size parameter to snprintf(). This would have triggered an annoying
WARN(). Now that we have converted to scnprintf() "size" will never
drop below 1 and there is no real need for this test. We could change
the condition to "if (temp <= 1) goto done;" but just deleting the test
is cleanest.
Fixes: 7d50195f6c ("usb: host: Faraday fotg210-hcd driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/ZXmwIwHe35wGfgzu@suswa
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 513d88a88e upstream.
Update the constant names for unused USB PIDs (product identifiers) to
reflect the new products now using the PIDs.
Signed-off-by: Mark Glover <mark.glover@actisense.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 772685c147 upstream.
This flash drive reports write protect during the first mode sense.
In the past this was not an issue as the kernel called revalidate twice,
thus asking the device for its write protect status twice, with write
protect being disabled in the second mode sense.
However, since commit 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") that is no longer the case, thus the
device shows up read only.
[490891.289495] sd 12:0:0:0: [sdl] Write Protect is on
[490891.289497] sd 12:0:0:0: [sdl] Mode Sense: 2b 00 80 08
This does not appear to be a timing issue, as enabling the usbcore quirk
USB_QUIRK_DELAY_INIT has no effect on write protect.
Fixes: 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable <stable@kernel.org>
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231207134441.298131-1-tasos@tasossah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73ea73affe upstream.
The KOBJ_CHANGE uevent is sent before gadget unbind is actually
executed, resulting in inaccurate uevent emitted at incorrect timing
(the uevent would have USB_UDC_DRIVER variable set while it would
soon be removed).
Move the KOBJ_CHANGE uevent to the end of the unbind function so that
uevent is sent only after the change has been made.
Fixes: 2ccea03a8f ("usb: gadget: introduce UDC Class")
Cc: stable@vger.kernel.org
Signed-off-by: Roy Luo <royluo@google.com>
Link: https://lore.kernel.org/r/20231128221756.2591158-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b17b7fe6dd upstream.
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released evaluates against the
released altmode's partner instead of the calling altmode itself, so change
adev in typec_altmode_put_partner to properly refer to the altmode being
released.
typec_altmode_set_partner is not run for port altmodes, so also add a check
in typec_altmode_release to prevent typec_altmode_put_partner() calls on
port altmode release.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231129192349.1773623-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24be0b3c40 upstream.
This reverts commit 4baf121815.
Enabling runtime pm as default for all AMD xHC 1.1 controllers caused
regression. An initial attempt to fix those was done in commit a5d6264b63
("xhci: Enable RPM on controllers that support low-power states") but new
issues are still seen.
Revert this to get those AMD xHC 1.1 systems working
This patch went to stable an needs to be reverted from there as well.
Fixes: 4baf121815 ("xhci: Loosen RPM as default policy to cover for AMD xHC 1.1")
Link: https://lore.kernel.org/linux-usb/55c50bf5-bffb-454e-906e-4408c591cb63@molgen.mpg.de
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20231205090548.1377667-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61890dc28f upstream.
The commit 89ff3dfac6 ("usb: gadget: f_hid: fix f_hidg lifetime vs
cdev") has introduced a bug that leads to hid device corruption after
the replug operation.
Reverse device managed memory allocation for the report descriptor
to fix the issue.
Tested:
This change was tested on the AMD EthanolX CRB server with the BMC
based on the OpenBMC distribution. The BMC provides KVM functionality
via the USB gadget device:
- before: KVM page refresh results in a broken USB device,
- after: KVM page refresh works without any issues.
Fixes: 89ff3dfac6 ("usb: gadget: f_hid: fix f_hidg lifetime vs cdev")
Cc: stable@vger.kernel.org
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Link: https://lore.kernel.org/r/20231206080744.253-2-aladyshev22@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 974bba5c11 ]
The BOS descriptor defines a root descriptor and is the base descriptor for
accessing a family of related descriptors.
Function 'usb_get_bos_descriptor()' encounters an iteration issue when
skipping the 'USB_DT_DEVICE_CAPABILITY' descriptor type. This results in
the same descriptor being read repeatedly.
To address this issue, a 'goto' statement is introduced to ensure that the
pointer and the amount read is updated correctly. This ensures that the
function iterates to the next descriptor instead of reading the same
descriptor repeatedly.
Cc: stable@vger.kernel.org
Fixes: 3dd550a2d3 ("USB: usbcore: Fix slab-out-of-bounds bug during device reset")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231115121325.471454-1-niklas.neronin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a09c12697 ]
It has been pointed out that the kernel log messages warning about
problems in USB configuration and related descriptors are vexing for
users. The warning log level has a fairly high priority, but the user
can do nothing to fix the underlying errors in the device's firmware.
To reduce the amount of useless information produced by tools that
filter high-priority log messages, we can change these warnings to
notices, i.e., change dev_warn() to dev_notice(). The same holds for
a few messages that currently use dev_err(): Unless they indicate a
failure that might make a device unusable (such as inability to
transfer a config descriptor), change them to dev_notice() also.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216630
Suggested-by: Artem S. Tashkinov <aros@gmx.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Y2KzPx0h6z1jXCuN@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 974bba5c11 ("usb: config: fix iteration issue in 'usb_get_bos_descriptor()'")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16b7e0cccb ]
Commits 7b8ef22ea5 ("usb: xhci: plat: Add USB phy support") and
9134c1fd05 ("usb: xhci: plat: Add USB 3.0 phy support") added support
for looking up legacy PHYs from the sysdev devicetree node and
initialising them.
This broke drivers such as dwc3 which manages PHYs themself as the PHYs
would now be initialised twice, something which specifically can lead to
resources being left enabled during suspend (e.g. with the
usb_phy_generic PHY driver).
As the dwc3 driver uses driver-name matching for the xhci platform
device, fix this by only looking up and initialising PHYs for devices
that have been matched using OF.
Note that checking that the platform device has a devicetree node would
currently be sufficient, but that could lead to subtle breakages in case
anyone ever tries to reuse an ancestor's node.
Fixes: 7b8ef22ea5 ("usb: xhci: plat: Add USB phy support")
Fixes: 9134c1fd05 ("usb: xhci: plat: Add USB 3.0 phy support")
Cc: stable@vger.kernel.org # 4.1
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Stanley Chang <stanley_chang@realtek.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Tested-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20231103164323.14294-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 41f5a09732 upstream.
The Qualcomm glue driver is overriding the interrupt trigger types
defined by firmware when requesting the wakeup interrupts during probe.
This can lead to a failure to map the DP/DM wakeup interrupts after a
probe deferral as the firmware defined trigger types do not match the
type used for the initial mapping:
irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
irq: type mismatch, failed to map hwirq-15 for interrupt-controller@b220000!
Fix this by not overriding the firmware provided trigger types when
requesting the wakeup interrupts.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231120161607.7405-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9feefbf57d upstream.
Make sure to remove the software node also on (ACPI) probe errors to
avoid leaking the underlying resources.
Note that the software node is only used for ACPI probe so the driver
unbind tear down is updated to match probe.
Fixes: 8dc6e6dd1b ("usb: dwc3: qcom: Constify the software node")
Cc: stable@vger.kernel.org # 5.12
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10d510abd0 upstream.
The default mode, configurable by DT, shall be set before usb role switch
driver is registered. Otherwise there is a race between default mode
and mode set by usb role switch driver.
Fixes: 98ed256a4d ("usb: dwc3: Add support for role-switch-default-mode binding")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231025095110.2405281-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0583bc776c upstream.
dwc2_hc_n_intr() writes back INTMASK as read but evaluates it
with intmask applied. In stress testing this causes spurious
interrupts like this:
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 7 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 0 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_update_urb_state_abn(): trimming xfer length
Applying INTMASK prevents this. The issue exists in all versions of the
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Ivan Ivanov <ivan.ivanov@suse.com>
Tested-by: Andrea della Porta <andrea.porta@suse.com>
Link: https://lore.kernel.org/r/20231115144514.15248-1-oneukum@suse.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58f2fcb3a8 upstream.
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
cc: stable@vger.kernel.org
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20231108093125.224963-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9cf87666fc ]
Make sure to free the "urs" platform device, which is created for some
ACPI platforms, on probe errors and on driver unbind.
Compile-tested only.
Fixes: c25c210f59 ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20231117173650.21161-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51392a1879 ]
The driver needs to deregister and free the newly allocated dwc3 core
platform device on ACPI probe errors (e.g. probe deferral) and on driver
unbind but instead it leaked those resources while erroneously dropping
a reference to the parent platform device which is still in use.
For OF probing the driver takes a reference to the dwc3 core platform
device which has also always been leaked.
Fix the broken ACPI tear down and make sure to drop the dwc3 core
reference for both OF and ACPI.
Fixes: 8fd95da2cf ("usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()")
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 9cf87666fc ("USB: dwc3: qcom: fix ACPI platform device leak")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a5d6264b63 upstream.
Use the low-power states of the underlying platform to enable runtime PM.
If the platform doesn't support runtime D3, then enabling default RPM will
result in the controller malfunctioning, as in the case of hotplug devices
not being detected because of a failed interrupt generation.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-16-mathias.nyman@linux.intel.com
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a04224da1f ]
Previously, gadget assignment to the net device occurred exclusively
during the initial binding attempt.
Nevertheless, the gadget pointer could change during bind/unbind
cycles due to various conditions, including the unloading/loading
of the UDC device driver or the detachment/reconnection of an
OTG-capable USB hub device.
This patch relocates the gether_set_gadget() function out from
ncm_opts->bound condition check, ensuring that the correct gadget
is assigned during each bind request.
The provided logs demonstrate the consistency of ncm_opts throughout
the power cycle, while the gadget may change.
* OTG hub connected during boot up and assignment of gadget and
ncm_opts pointer
[ 2.366301] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105
[ 2.366304] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.366306] usb 2-1.5: Product: H2H Bridge
[ 2.366308] usb 2-1.5: Manufacturer: Aptiv
[ 2.366309] usb 2-1.5: SerialNumber: 13FEB2021
[ 2.427989] usb 2-1.5: New USB device found, VID=2996, PID=0105
[ 2.428959] dabridge 2-1.5:1.0: dabridge 2-4 total endpoints=5, 0000000093a8d681
[ 2.429710] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed
[ 2.429714] dabridge 2-1.5:1.0: Hub 2-2 P(0151) V(06.87)
[ 2.429956] dabridge 2-1.5:1.0: All downstream ports in host mode
[ 2.430093] gadget 000000003c414d59 ------> gadget pointer
* NCM opts and associated gadget pointer during First ncm_bind
[ 34.763929] NCM opts 00000000aa304ac9
[ 34.763930] NCM gadget 000000003c414d59
* OTG capable hub disconnecte or assume driver unload.
[ 97.203114] usb 2-1: USB disconnect, device number 2
[ 97.203118] usb 2-1.1: USB disconnect, device number 3
[ 97.209217] usb 2-1.5: USB disconnect, device number 4
[ 97.230990] dabr_udc deleted
* Reconnect the OTG hub or load driver assaign new gadget pointer.
[ 111.534035] usb 2-1.1: New USB device found, idVendor=2996, idProduct=0120, bcdDevice= 6.87
[ 111.534038] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 111.534040] usb 2-1.1: Product: Vendor
[ 111.534041] usb 2-1.1: Manufacturer: Aptiv
[ 111.534042] usb 2-1.1: SerialNumber: Superior
[ 111.535175] usb 2-1.1: New USB device found, VID=2996, PID=0120
[ 111.610995] usb 2-1.5: new high-speed USB device number 8 using xhci-hcd
[ 111.630052] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105, bcdDevice=21.02
[ 111.630055] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 111.630057] usb 2-1.5: Product: H2H Bridge
[ 111.630058] usb 2-1.5: Manufacturer: Aptiv
[ 111.630059] usb 2-1.5: SerialNumber: 13FEB2021
[ 111.687464] usb 2-1.5: New USB device found, VID=2996, PID=0105
[ 111.690375] dabridge 2-1.5:1.0: dabridge 2-8 total endpoints=5, 000000000d87c961
[ 111.691172] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed
[ 111.691176] dabridge 2-1.5:1.0: Hub 2-6 P(0151) V(06.87)
[ 111.691646] dabridge 2-1.5:1.0: All downstream ports in host mode
[ 111.692298] gadget 00000000dc72f7a9 --------> new gadget ptr on connect
* NCM opts and associated gadget pointer during second ncm_bind
[ 113.271786] NCM opts 00000000aa304ac9 -----> same opts ptr used during first bind
[ 113.271788] NCM gadget 00000000dc72f7a9 ----> however new gaget ptr, that will not set
in net_device due to ncm_opts->bound = true
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20231020153324.82794-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e72fc8d6a1 ]
In Synopsys's dwc3 data book:
To avoid underrun and overrun during the burst, in a high-latency bus
system (like USB), threshold and burst size control is provided through
GTXTHRCFG and GRXTHRCFG registers.
In Realtek DHC SoC, DWC3 USB 3.0 uses AHB system bus. When dwc3 is
connected with USB 2.5G Ethernet, there will be overrun problem.
Therefore, setting TX/RX thresholds can avoid this issue.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230912041904.30721-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5f928db59 ]
If this driver enables the xHC clocks while resuming from sleep, it calls
clk_prepare_enable() without checking for errors and blithely goes on to
read/write the xHC's registers -- which, with the xHC not being clocked,
at least on ARM32 usually causes an imprecise external abort exceptions
which cause kernel oops. Currently, the chips for which the driver does
the clock dance on suspend/resume seem to be the Broadcom STB SoCs, based
on ARM32 CPUs, as it seems...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: 8bd954c561 ("usb: host: xhci-plat: suspend and resume clocks")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4baf121815 ]
The AMD USB host controller (1022:43f7) isn't going into PCI D3 by default
without anything connected. This is because the policy that was introduced
by commit a611bf473d ("xhci-pci: Set runtime PM as default policy on all
xHC 1.2 or later devices") only covered 1.2 or later.
The 1.1 specification also has the same requirement as the 1.2
specification for D3 support. So expand the runtime PM as default policy
to all AMD 1.1 devices as well.
Fixes: a611bf473d ("xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices")
Link: https://composter.com.ua/documents/xHCI_Specification_for_USB.pdf
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9747576348 ]
If a hub is disconnected that has device(s) that's attached to the usbip layer
the disconnect function might fail because it tries to release the port
on an already disconnected hub.
Fixes: 6080cd0e92 ("staging: usbip: claim ports used by shared devices")
Signed-off-by: Jonas Blixt <jonas.blixt@actia.se>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230615092810.1215490-1-jonas.blixt@actia.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
